Search NASA⌕ Search

SEARCH · Search NASA

Results for “NISAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Aboveground Biomass Estimation Using NISAR Simulated ALOS-2 Time Series Data

Aboveground biomass (AGB) is a critical parameter to better understand the global carbon cycle and to develop sustainable forest management. However, a large uncertainty prevails. L-band SAR data have demonstrated strong potential to accurately retrieve AGB over low-biomass regions (<100 Mg ha-1). The upcoming NASA-ISRO Synthetic Aperture Radar mission will collect data at L- and S-band over earth’s landmass with a repeat period of 12 days, allowing us to have ample data for monitoring biomass and its dynamics. One of the key science requirements of the mission is to produce annual AGB maps at 1-ha resolution with RMS accuracy of 20 Mg/ha for 80 percentage of area over low-biomass regions in Calibration/Validation sites. The NISAR biomass algorithm will generate AGB maps based on the parameterization of semi-empirical model along with NISAR time-series dual pol data (HH and HV). To calibrate and validate the model for mission requirements, the mission will use reference estimates of AGB produced from ground inventory plots and airborne LiDAR data collected over selected sites distributed across different global ecoregions. This paper presents the initial results of the calibration/validation of the NISAR AGB retrieval algorithm over the Lenoir Landing (LENO), Alabama, USA site using NISAR simulated ALOS-2 time series data. Five multi-temporal dual-pol HH and HV NISAR Simulated ALOS 2 data collections were used as input to assess the performance of the model. The model AGB retrieval results shows that the NISAR model was able to achieve RMS accuracy within 20 Mg/ha.

Ramachandran, Naveen [Jet Propulsion Laboratory, C↗
DOE OSTI2024

Ecosystem Science with NISAR: Final Preparations in The Pre-Launch Period

The NISAR mission which in its most recent round of launch preparations was set to launch in the spring of 2024, and now delayed until later in the fall or early spring of 2025, will serve as an unprecedented resource for the Remote Sensing of Ecosystems Science community. The two frequency, L- and S-band will full-polarimetric capability over a 250 km wide swath using the SweepSAR technique [1] will collect reliable set of observations (60 per year; 30 each for ascending and descending passes) on a continuing basis that will allow for the modeling and observation of time-varying processes that are prevalent in the living environment broadly described as Ecosystems. Among the prime science goals of the NISAR Ecosystems disciplines are in the characterization of agriculture, disturbance, biomass, forest structure and water dynamics seen in the world’s rivers, coasts, and permafrost regions. In this paper we provide an overview of the Ecosystem science that will be enabled by the NISAR mission and give a status of the basic algorithms that are being used to provide a basic set of tools to the community to make use of the data that NISAR will provide.

Siqueira, Paul↗
DOE OSTI2024

The NASA ISRO SAR (NISAR) Mission - Validation of Science Measurement Requirements

The NASA ISRO Synthetic Aperture Radar (NISAR) is scheduled for launch early in 2024 from the Satish Dhawan Space Centre (SDSC), at Sriharikota, near Chennai, India. This mission is the result of a collaboration between NASA and Indian Space Research Organization (ISRO), where NASA has contributed elements of the mission such as an L-band SAR, and ISRO has contributed other elements, such as an S-band SAR. After successful launch, the NISAR mission will collect left-looking L-band SAR data over most of the Earth’s land areas twice during every 12-day exact repeat orbit. (once while in an ascending orbit direction and once while in a descending orbit direction). NASA and ISRO have individual and joint requirements on the mission that include the performance of the imaging radars onboard the spacecraft. For example, NASA must demonstrate that this L-band SAR will achieve a set of identified science measurement accuracy requirements that span Ecosystem science, Solid Earth science, and Cryosphere science disciplines. Likewise, ISRO has several applications objectives on both the L-band and S-band data from NISAR that the ISRO science team and project will be developing and testing. Pre-launch and post-launch activities have been planned to validate that these requirements are met. Here, we will discuss how the NASA plans are being executed and will present any initial results at the conference.

Chapman, Bruce↗
DOE OSTI2024

Preparing an on-Demand Cloud Processing Workflow for NISAR Ecosystems Science Products

In preparation for the NISAR launch and data collection in 2024, the NISAR Project Science Team is building workflows for each Science Team discipline (Ecosystems, Cryosphere, and Solid Earth). This abstract focuses on the Ecosystem disciplines and the development of on-demand cloud-processing workflows for wetlands inundation, forest biomass, agricultural active crop area, and forest disturbance. The workflow simulates NISAR data using UAVSAR or ALOS-2 Single Look Complex data, which are processed to Level 2 geocoded polarimetric covariance matrix products using InSAR Scientific Computing Environment 3.0 software and to Level 3 science products using the Algorithm Theoretical Basis Documents. In this presentation, we describe these workflows and efforts to improve efficiency and data accessibility by using a cloud processing system. We present preliminary sample products from each Ecosystem discipline: inundation, forest biomass, crop area, and forest disturbance.

Christensen, Alexandra↗
DOE OSTI2026

Exploring the potential of using L-Band InSAR for the mapping of flooded vegetation in tropical wetlands

Wetlands play a critical role in global water and carbon cycles, yet monitoring their water extent remains difficult, particularly beneath dense vegetation. SAR-based techniques such as backscatter thresholding are limited by complex scattering mechanisms, while fully polarimetric SAR (PolSAR) data capable of detecting doublebounce scattering remain scarce. To address these challenges, this study evaluates the potential of Interferometric SAR (InSAR) for mapping water surfaces beneath vegetation, termed flooded vegetation, using the Atrato floodplain in Colombia as a case study. We develop an automated workflow combining InSAR fringe detection with local phase homogeneity analysis and random sampling of processing parameters to generate probabilistic flooded vegetation maps. Applied to ALOS PALSAR-1 L-band image pairs from 2007–2011, the workflow captures seasonal fluctuations in flooded extent ranging from 500 to 1,500 km2. Compared to other L-band SAR inundation products, the InSAR-based maps identify broader flooded areas, with ~70% agreement in pairwise comparisons. Around 84% of detections align with existing wetland inventories and seasonal changes correspond with regional hydrological indicators, including terrestrial water storage anomalies and water gauge measurements. PolSAR analysis shows that InSAR complements backscatter-based methods by detecting inundation in areas with weak double-bounce signals. These findings suggest that combining InSAR with backscatter-based methods can improve detection of flooded vegetation, which is especially relevant for the upcoming NISAR mission that will offer frequent global L-band observations.

Coastal inundation↗
DOE OSTI2023

Fracture‐Resistant and Thermally Insulating Ultrahigh‐Temperature Carbide Foams

Dense ultrahigh‐temperature ceramics (UHTCs) carbides are recognized as potential materials for thermal protection systems (TPS) owing to properties beyond existing structural materials’ capabilities. Recent advances in UHTCs have enabled the development of multiscale porous microstructures. Herein, it is highlighted that the porosity in UHTCs are no longer treated as a defect but as a functional property specifically tailored for thermal insulation. It is a promising solution to design and fabricate bulk UHTC foams via a freeze‐drying (FD) approach followed by calibrated pressureless spark plasma sintering. Herein, monolithic TaC and HfC UHTC foams and their composite show the partial solid–solution formation of (Ta, Hf)C with porosity ≥50%. TaC–HfC foam (≈80–92 N) shows an intermediate load‐bearing capability compared to monolithic TaC (≈120–135 N) and HfC (≈28–35 N) foams, with no evident cracking on the sample surface. The thermal conductivity of partial solid‐solution TaC–HfC foam increases up to fivefold compared to parent UHTC foams. In the results, solid solutions’ efficacy and pores’ unidirectionality in providing thermal insulation to TaC–HfC while maintaining its high‐load bearing capability are illustrated. In conclusion, the developed technique establishes a new paradigm shift in UHTCs, expanding their potential for TPS in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Valuation of Anode Materials for High-Performance Lithium Batteries: From Graphite to Lithium Metal and Beyond

Lithium-ion batteries have revolutionized energy storage, yet advanced technologies such as electric vehicles and eVTOLs demand even higher performance and safety. Anodes, the negative electrodes, are crucial in enhancing batteries’ safety, lifespan, and fast-charging capabilities. This review paper comprehensively evaluates the progression of anode materials from traditional graphite to advanced anodes like lithium metal. Graphite anodes, with a capacity of 372 mAh g −1 , enabled the first commercial lithium-ion batteries, but future applications require higher energy densities and fast-charging capabilities. Emerging anode materials, including alloying, and conversion types, as well as lithium metal, offer significantly higher capacities, with lithium metal offering a theoretical capacity of 3 860 mAh g −1 . However, these advanced anodes face challenges such as volume expansion, high surface reactivity, sluggish Li+ kinetics, and unstable lithium deposition morphologies. Here, this review critically examines the electrochemical performance, interfacial properties, mechanical attributes, and stability issues of various anode materials. It further discusses solid electrolyte interphase (SEI) formation, strategies for enhancing interface stability, and the requirements of anodes for solid-state batteries. Additionally, the review explores potential solutions for limitations with each anode type, highlights innovative anode-free architectures, and evaluates the current and future trends of battery anode industries. Ultimately, this paper aims to guide the development of high-performance anode materials, paving the way for the next generation of efficient, reliable lithium batteries.

Alloying anodes↗
DOE OSTI2025

The imaging Time-of-Propagation detector at Belle II

Here, we report on the construction, operation, and performance of the Time-of-Propagation detector with imaging used for the Belle II experiment running at the Super-KEKB e + e - collider. This detector is located in the central barrel region and uses Cherenkov light to provide particle identification among hadrons. The Cherenkov light is radiated in highly polished bars of synthetic fused silica (quartz) and transported to the ends of the bars via total internal reflection. One bar end is instrumented with finely segmented micro-channel-plate photomultiplier tubes to record the light, while the other end has a mirror attached to reflect the photons back to the instrumented end. Both the propagation times and hit positions of the Cherenkov photons are measured; these depend on the Cherenkov angle and together provide good discrimination among charged pions, kaons, and protons with momenta up to around 4 GeV/ c . To date, the detector has been used to record and analyze almost 600 fb −1 of Belle II data.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Enhancing Hydrogen Production from Bioenergy Crops via Photoreforming

Photoreforming perennial bioenergy crops (willow, Miscanthus , and poplar) has the potential to produce H 2 with reduced environmental impacts. To understand the compositional effects of the biomass on the average rate of H 2 production over the first 30 min of reaction ( r H 2 ), the r H 2 values of model biomass component (i.e., cellulose, hemicellulose, and lignin) mixtures were compared with those from the raw biomass. The higher cellulose or hemicellulose content in multicomponent mixtures resulted in higher r H 2 , whereas lignin reduced the hydrogen production rate. However, with raw biomass, the ratio of biomass components alone did not determine the r H 2 via photoreforming, with rates of hydrogen production for different varieties of willow ranging between 1.9 μmol h -1 and 12.3 μmol h -1 , 11.8 μmol h -1 for a poplar, and 6.8 μmol h -1 for a miscanthus biomass. In addition, comparable r H 2 values of raw poplar and its extracted cellulose via an IonoSolv treatment indicated the possibility of using raw biomass materials without delignification for generating H 2 via photoreforming. Importantly, r H 2 was positively correlated with the interaction between water and the biomass, as assessed by NMR relaxation via an examination of the T 1 /T 2 ratio. A stronger water-biomass interaction resulted in a higher r H 2 . Genetic modification of biomass has been suggested as a putative way to improve the r H 2 of biomass with an enhanced interaction with water. This research enhances the understanding of factors influencing H 2 production from lignocellulosic biomass by photoreforming and supports the breeding and management of perennial biomass crops to maximize H 2 yields while minimizing land area requirements.

biomass↗
DOE OSTI2025

Intrinsically Bifunctional and Tunable Tungsten Carbide Catalysts Enable Efficient PVC-Compatible Polyolefin Hydrocracking

Hydrocracking is a promising route for the chemical recycling of polyolefins (PO), converting them into short hydrocarbons over bifunctional catalysts with metal sites for hydrogenation and dehydrogenation, and Brønsted acid sites (BAS) for isomerization and C–C bond cleavage. However, PO feedstocks containing polyvinyl chloride (PVC) can release chlorine (Cl) under reaction conditions, deactivating conventional noble metal/zeolite catalysts. Moreover, the lack of site intimacy and the presence of micropores within conventional catalysts create challenges around the transport of high-molecular-weight, sterically encumbered polymer intermediates. Here, in this study, we report tungsten carbides (W x C) as a novel type of bifunctional catalysts that address these challenges. W/W 2 C phases on W x C offer “metal” sites, and −OH on WO x species introduces BAS in close proximity. The “metal”:BAS ratio can be tuned through carburization temperature, leading to a volcano-shaped activity trend reflecting the requirement for metal–BAS balance. Kinetic data demonstrate that each PO chain undergoes sequential cleavage, while trends in cracking ideality and selectivity follow those in short-alkane hydrocracking. On the per-BAS basis, W x C is more efficient than conventional bifunctional catalysts by more than an order of magnitude, due to enhanced polymer transport. They maintain or show increased activity with 10 wt % PVC in the substrate. This work establishes transition-metal carbides as earth-abundant bifunctional catalysts with unique site proximity and heteroatom compatibility. These features, along with the broad structure space for rational tuning, make them promising options to tackle specific challenges that polymer feedstocks present in hydrocracking.

Nwachukwu, Uchenna C. [Univ. of Akron, OH (United ↗
DOE OSTI2023

Ultra-high temperature carbide foams and methods of fabricating the same

Ultra-high temperature carbide (UHTC) foams and methods of fabricating and using the same are provided. The UHTC foams are produced in a three-step process, including UHTC slurry preparation, freeze-drying, and spark plasma sintering (SPS). The fabrication methods allow for the production of any kind of single- or multi-component UHTC foam, while also providing flexibility in the shape and size of the UHTC foams to produce near-net-shape components.

Agarwal, Arvind↗