Search NASA⌕ Search

SEARCH · Search NASA

Results for “NOISE MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Quiet Clean Short-haul Experimental Engine (QCSEE). Core engine noise measurements

Noise measurements were taken on a turbofan engine which uses the same core, with minor modifications, employed on the quiet clean short-haul experimental engine (QCSEE) propulsion systems. Both nearfield and farfield noise measurements were taken in order to determine the core internally generated noise levels. The resulting noise measurements were compared to predicted combustor and turbine noise levels, to verify or improve the predicted QCSEE combustor and turbine noise levels.

Sowers, H. D.↗
NASA NTRS1976

Investigation of the effects of a moving acoustic medium on jet noise measurements

Noise from an unheated sonic jet in the presence of an external flow is measured in a free-jet wind tunnel using microphones located both inside and outside the flow. Comparison of the data is made with results of similar studies. The results are also compared with theoretical predictions of the source strength for jet noise in the presence of flow and of the effects of sound propagation through a shear layer.

Cole, J. E., III↗
NASA NTRS1967

Edge-type connectors evaluated by electrical noise measurement

Electrical noise measurement system measures noise generated by edge-type connectors and circuit cards when they are subjected to sinusoidal vibration. It provides a signal across the contact area and monitors the signal change during vibration. Noise measured can be expressed as a varying change in total contact resistance.

Brummett, S. L.↗
NASA NTRS2011

High-Tc Superconducting Bolometer Noise Measurement Using Low Noise Transformers - Theory and Optimization

Care must always be taken when performing noise measurements on high-Tc superconducting materials to ensure that the results are not from the measurement system itself. One situation likely to occur is with low noise transformers. One of the least understood devices, it provides voltage gain for low impedance inputs (< 100 ), e.g., YBaCuO and GdBaCuO thin films, with comparatively lower noise levels than other devices for instance field effect and bipolar junction transistors. An essential point made in this paper is that because of the complex relationships between the transformer ports, input impedance variance alters the transformer s transfer function in particular, the low frequency cutoff shift. The transfer of external and intrinsic transformer noise to the output along with optimization and precautions are treated; all the while, we will cohesively connect the transfer function shift, the load impedance, and the actual noise at the transformer output.

Aslam, Shahid↗
NASA NTRS2016

Measured Noise from Small Unmanned Aerial Vehicles

Proposed uses of small unmanned aerial vehicles (UAVs), including home package delivery, have the potential to expose large portions of communities to a new noise source. This paper discusses results of flyover noise measurements of four small UAVs, including an internal combustion-powered model airplane and three battery-powered multicopters. Basic noise characteristics of these vehicles are discussed, including spectral properties and sound level metrics such as sound pressure level, effective perceived noise level, and sound exposure level. The size and aerodynamic characteristics of the multicopters in particular make their flight path susceptible to atmospheric disturbances such as wind gusts. These gusts, coupled with a flight control system that varies rotor speed to maintain vehicle stability, create an unsteady acoustic signature. The spectral variations resulting from this unsteadiness are explored, in both hover and flyover conditions for the multicopters. The time varying noise, which differs from the relatively steady noise generated by large transport aircraft, may complicate the prediction of human annoyance using conventional sound level metrics.

Cabell, Randolph↗
NASA NTRS1975

Measured noise reductions resulting from modified approach procedures for business jet aircraft

Five business jet airplanes were flown to determine the noise reductions that result from the use of modified approach procedures. The airplanes tested were a Gulfstream 2, JetStar, Hawker Siddeley 125-400, Sabreliner-60 and LearJet-24. Noise measurements were made 3, 5, and 7 nautical miles from the touchdown point. In addition to a standard 3 deg glide slope approach, a 4 deg glide slope approach, a 3 deg glide slope approach in a low-drag configuration, and a two-segment approach were flown. It was found that the 4 deg approach was about 4 EPNdB quieter than the standard 3 deg approach. Noise reductions for the low-drag 3 deg approach varied widely among the airplanes tested, with an average of 8.5 EPNdB on a fleet-weighted basis. The two-segment approach resulted in noise reductions of 7 to 8 EPNdB at 3 and 5 nautical miles from touchdown, but only 3 EPNdB at 7 nautical miles from touchdown when the airplanes were still in level flight prior to glide slope intercept. Pilot ratings showed progressively increasing workload for the 4 deg, low-drag 3 deg, and two-segment approaches.

Burcham, F. W., Jr.↗
NASA NTRS1972

Measured noise of model fan-under-wing and fan-on-flap jet flap configurations

Noise measurements were made on two jet flap systems proposed for STOL aircraft. In one case a 14.0-cm- (5.5-in.-) diameter fan was mounted under the wing such that the exhaust impinged on downwardly deflected flap segments. In the other case, the fan was located on the upper surface of the flap such that fan and flap moved as a unit, with no exhaust impingement. Results for takeoff and approach fan speeds and flap deflections were used to estimate STOL airplane perceived noise levels. Internally generated noise directivity corresponded with fan axis orientation for the fan-on-flap, but no consistent redirection of internal noise was observed with changes in flap angle for the fan-under-wing. With the fan-on-flap arrangement, the wing shielded some fan inlet noise from the ground. Since no impingement of the exhaust on solid surfaces occurred, the external noise was jet noise alone. In contrast, for the fan-under-wing, the jet/flap interaction noise dominated the external noise except at angles near the jet axis even with no flap deflection. If internal noise is reduced by fan design and acoustic treatment, the jet/flap interaction noise will dominate.

Groeneweg, J. F.↗
NASA NTRS2010

Data Quality Assurance for Supersonic Jet Noise Measurements

The noise created by a supersonic aircraft is a primary concern in the design of future high-speed planes. The jet noise reduction technologies required on these aircraft will be developed using scale-models mounted to experimental jet rigs designed to simulate the exhaust gases from a full-scale jet engine. The jet noise data collected in these experiments must accurately predict the noise levels produced by the full-scale hardware in order to be a useful development tool. A methodology has been adopted at the NASA Glenn Research Center s Aero-Acoustic Propulsion Laboratory to insure the quality of the supersonic jet noise data acquired from the facility s High Flow Jet Exit Rig so that it can be used to develop future nozzle technologies that reduce supersonic jet noise. The methodology relies on mitigating extraneous noise sources, examining the impact of measurement location on the acoustic results, and investigating the facility independence of the measurements. The methodology is documented here as a basis for validating future improvements and its limitations are noted so that they do not affect the data analysis. Maintaining a high quality jet noise laboratory is an ongoing process. By carefully examining the data produced and continually following this methodology, data quality can be maintained and improved over time.

Brown, Clifford A.↗
NASA NTRS1987

Rotor noise measurement using a directional microphone array

A directional array of microphones was used to measure the noise from a 40 percent scale model rotor in a large aeroacoustic wind tunnel. The development and design of this directional array is described. A design goal was that the array focus on a constant sensing area over a broad frequency range. The implementation of the array design is presented, followed by sample results for several different rotor test conditions. The directional array spectral results are compared with predictions of broadband self noise, and with total rotor noise measurements obtained from individual microphones of the array. The directional array is demonstrated to be a useful tool in examining noise source distributions.

Marcolini, Michael A.↗
NASA NTRS1974

Jet transport noise - A comparison of predicted and measured noise for ILS and two-segment approaches

Centerline noise measured during standard ILS and two-segment approaches in DC-8-61 aircraft were compared with noise predicted for these procedures using an existing noise prediction technique. Measured data is considered to be in good agreement with predicted data. Ninety EPNdB sideline locations were calculated from flight data obtained during two-segment approaches and were compared with predicted 90 EPNdB contours that were computed using three different models for excess ground attenuation and a contour with no correction for ground attenuation. The contour not corrected for ground attenuation was in better agreement with the measured data.

White, K. C.↗
NASA NTRS1974

Noise measurements obtained during engineering evaluation of two-segment approaches in a 727-200 aircraft

A series of noise measurements were made during engineering evaluation tests of two-segment approaches in a 727-200 aircraft equipped with acoustically treated nacelles. A two-segment approach having a 6-degree upper glide slope angle intercepting the Instrument Landing System (ILS) 2.9-degree glide slope at an altitude of 690 feet gave a 5-EPNdB decrease in measured noise at distances greater than 3 nautical miles from the runway threshold when compared with a normal ILS approach. Several of the noise measurements were taken under adverse weather conditions which were outside the specified limits of FAR Part 36. This may introduce uncertainties into the data from several approaches.

Tanner, C. S.↗
NASA NTRS1983

Identification of structural systems using naturally induced vibration data in the presence of measurement noise

The method of instrument variables for the identification of the parameters of structural systems excited by white noise in the presence of white measurement noise is applied. The requisite equations and the resulting consistent estimator are derived and simulation results for least squares and instrumental variables methods, for light and heavy damping, are compared. The present method gave better results than least squares when measurement noise was presented, and verified the fact that least squares yields an inconsistent estimator unless the measurement noise is zero.

Huan, S.-L.↗
NASA NTRS1972

Noise measurements obtained during visual approach monitor evaluation in 747 aircraft

The results are reported of acoustic measurements made on the 747 aircraft during visual approach monitor evaluation approaches. This display is designed to improve approach and landing precision under visual flight rule conditions. The purpose of the acoustic portion of the test was to measure, evaluate, and identify the noise levels during various types of aircraft approaches. Six noise measurement sites were positioned on the centerline of the approach ground track. The six noise measurement stations on the approach ground track were positioned between approximately 1 and 6 nautical miles from runway threshold. The 1-nautical mile point was chosen as the beginning of the ground track because it is specified as the approach measurement point in the FAA noise certification requirements. The 6-nautical mile point was chosen for its proximity to the point where the approach is initiated.

Tanner, C. S.↗
NASA NTRS2021

Noise Measurements from Ground Tests of the Moog SureFly Vehicle

Noise measurements from a ground test of a small vertical lift research vehicle are presented. The proof-of-concept all-electric vehicle called “SureFly” was developed by Moog, Inc. A cooperative effort between NASA and Moog, Inc. has led to one of the first acoustic test datasets from an Urban Air Mobility (UAM) vehicle being developed for passenger and cargo. Results show propeller and possibly motor tones are important for the overall noise levels. The vehicle has four support arms each with a pair of contra-rotating propellers. Noise measurements show higher noise levels from the lower propellers, likely due to inflow distortion from the arms and top propellers. Possible motor noise was identified by calculating harmonics of the line frequency and comparing to the tones in the narrowband acoustic spectra and phased microphone array data. The acoustic far field was found to be about 100 ft away from the vehicle, but additional microphones are needed to provide a better assessment. Results show the presence of modulation for some test conditions. The work reported here is only for ground tests.

Acoustics↗
NASA NTRSDate not supplied

Noise Measurements from Ground Tests of the Moog SureFly Vehicle

Noise measurements from a ground test of a small vertical lift research vehicle are presented. The proof-of-concept all-electric vehicle called “SureFly” was developed by Moog, Inc. A cooperative effort between NASA and Moog, Inc. has led to one of the first acoustic test datasets from an Urban Air Mobility (UAM) vehicle being developed for passenger and cargo. Results show propeller and possibly motor tones are important for the overall noise levels. The vehicle has four support arms each with a pair of contra-rotating propellers. Noise measurements show higher noise levels from the lower propellers, likely due to inflow distortion from the arms and top propellers. Possible motor noise was identified by calculating harmonics of the line frequency and comparing to the tones in the narrowband acoustic spectra and phased microphone array data. The acoustic far field was found to be about 100 feet away from the vehicle, but additional microphones are needed to provide a better assessment. Results show the presence of modulation for some test conditions. The work reported here is only for ground tests.

Acoustics↗