Search NASA⌕ Search

SEARCH · Search NASA

Results for “NbSN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

Materials Data on Tb(NbSn)6 by Materials Project

Tb(NbSn)6 crystallizes in the hexagonal P6/mmm space group. The structure is three-dimensional. Tb is bonded to eight Sn atoms to form distorted edge-sharing TbSn8 hexagonal bipyramids. There are two shorter (3.18 Å) and six longer (3.36 Å) Tb–Sn bond lengths. Nb is bonded in a 12-coordinate geometry to six Sn atoms. There are a spread of Nb–Sn bond distances ranging from 2.92–3.01 Å. There are three inequivalent Sn sites. In the first Sn site, Sn is bonded in a 6-coordinate geometry to six equivalent Nb atoms. In the second Sn site, Sn is bonded in a 12-coordinate geometry to three equivalent Tb and six equivalent Nb atoms. In the third Sn site, Sn is bonded in a 8-coordinate geometry to one Tb, six equivalent Nb, and one Sn atom. The Sn–Sn bond length is 3.25 Å.

36 MATERIALS SCIENCE↗

Materials Data on NbSN by Materials Project

Computed materials data using density functional theory calculations. These calculations determine the electronic structure of bulk materials by solving approximations to the Schrodinger equation. For more information, see https://materialsproject.org/docs/calculations

36 MATERIALS SCIENCE↗

Thermodynamic re-modelling of the Cu–Nb–Sn system: Integrating the nausite phase

Currently available Cu–Nb–Sn phase diagrams lack the recently discovered nausite phase (Cu,Nb)Sn 2 , which is an important intermediate in the course of thermal processing of superconducting Nb 3 Sn wires. Processing decisively determines the resulting microstructure of Nb 3 Sn and, thus, its superconducting properties. Lack of suitable and complete phase diagrams, however, obstructs rational design of such thermal processing procedures. To close this gap and to obtain valid knowledge of homogeneity and stability range of nausite, various Cu–Nb–Sn samples, which are heat-treated between 300 °C and 500 °C, are investigated. By means of energy-dispersive X-ray spectroscopy (EDX), a temperature-dependent homogeneity range of nausite is observed, which covers average mole fractions of Cu between 0.09 and 0.15. This is correlated with a change in the mean atomic volume and can be seen in the lattice parameters determined by X-ray diffraction (XRD). Additionally performed first-principles calculations on different CuSn 2 and NbSn 2 model structures confirm this trend. Furthermore, the peritectic decomposition of nausite to NbSn 2 and liquid at 586 °C is determined by means of in situ XRD and differential scanning calorimetry (DSC). By using the CALPHAD (CALculation of PHase Diagrams) approach, all these findings are used to extend a previous thermodynamic description of the Cu–Nb–Sn system by including the nausite as an additional phase. Finally, with this noteworthy integration, the updated modelling of the Cu–Nb–Sn system can be used for optimizing the multistage heat-treatment steps during processing superconducting Nb 3 Sn wires.

36 MATERIALS SCIENCE↗

Controlling Cu–Sn mixing so as to enable higher critical current densities in RRP ® Nb 3 Sn wires

Dipole magnets for the proposed Future Circular Collider (FCC) demand specifications significantly beyond the limits of all existing Nb 3 Sn wires, in particular a critical current density (J c ) of more than 1500 A mm -2 at 16 T and 4.2 K with an effective filament diameter (D eff ) of less than 20 μm. The restacked-rod-process (RRP ® ) is the technology closest to meeting these demands, with a J c (16 T) of up to 1400 A mm -2 , residual resistivity ratio > 100, for a sub-element size D s of 58 μm (which in RRP ® wires is essentially the same as D eff ). An important present limitation of RRP ® is that reducing the sub-element size degrades J c to as low as 900 A mm -2 at 16 T for D s = 35 μm. To gain an understanding of the sources of this J c degradation, we have made a detailed study of the phase evolution during the Cu–Sn 'mixing' stages of the wire heat treatment that occur prior to Nb 3 Sn formation. Using extensive microstructural quantification, we have identified in this paper the critical role that the Sn–Nb–Cu ternary phase (Nausite) can play. The Nausite forms as a well-defined ring between the Sn source and the Cu/Nb filament pack, and acts as an osmotic membrane in the 300 °C–400 °C range—greatly inhibiting Sn diffusion into the Cu/Nb filament pack while supporting a strong Cu counter-diffusion from the filament pack into the Sn core. This converts the Sn core into a mixture of the low melting point (408 °C) η phase (Cu 6 Sn 5 ) and the more desirable ε phase (Cu 3 Sn), which decomposes at 676 °C. After the mixing stages, when heated above 408 °C towards the Nb 3 Sn reaction, any residual η liquefies to form additional irregular Nausite on the inside of the membrane. All Nausite decomposes into NbSn 2 on further heating, and ultimately transforms into coarse-grain (and often disconnected) Nb 3 Sn which has little contribution to current transport. Understanding this critical Nausite reaction pathway has allowed us to simplify the mixing heat treatment to only one stage at 350 °C for 400 h which minimizes Nausite formation while encouraging the formation of the higher melting point ε phase through better Cu–Sn mixing. Finally, at a D s of 41 μm, the Nausite control heat treatment increases the J c at 16 T by 36%, reaching 1300 A mm -2 (i.e. 2980 A mm -2 at 12 T), and moving RRP ® closer to the FCC targets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improvement of small to large grain A15 ratio in Nb 3 Sn PIT wires by inverted multistage heat treatments

The next generation of superconducting accelerator magnets for the Large Hadron Collider at CERN will require large amounts of Nb 3 Sn superconducting wires and the Powder-In-Tube (PIT) process, which utilizes a NbSn 2 -rich powder core within tubes of Nb(7.5wt%Ta) contained in a stabilizing Cu matrix, is a potential candidate. But, the critical current density, J c , is limited by the formation of a large grain (LG) A15 layer which does not contribute to transport current, but occupies 25-30% of the total A15 area. Thus it is important to understand how this layer forms, and if it can be minimized in favor of the beneficial small grain (SG) A15 morphology which carries the supercurrent. The ratio of SG/LG A15 is our metric here, where an increase signals improvement in the wires A15 morphology distribution. We have made a critical new observation that the initiation of the LG A15 formation can be controlled at a wide range of temperatures relative to the formation of the small grain (SG) A15. The LG A15 can be uniquely identified as a decomposition product of the Nb6Sn5(Cu x ), surrounded by a layer of rejected Cu, thus the LG A15 is not only of low pin density, but is not continuous grain to grain. We have found that in single stage reactions limited to 630 °C - 690 °C, the maximum SG A15 layer thickness prior to LG A15 formation is very sensitive to temperature, with a maximum around 670 °C. This result led to the design of four novel heat treatments which all included a short, high temperature stage early in the reaction, followed by a slow cooling to a more typical reaction temperature of 630 °C. We also found that this heat treatment (HT) modification increased the SG A15 layer thickness while simultaneously suppressing LG A15 morphology, with no additional consumption of the diffusion barrier. In the best heat treatment the SG/LG A15 ratio improved by 30%. Unfortunately, J c values suffered slightly, however further exploration of this high temperature reaction region is required to understand the limits to A15 formation in Nb3Sn PIT conductors.

36 MATERIALS SCIENCE↗

Thermodynamic modeling of the Ti-Nb-Sn system and its preliminary applications in aging precipitation and solidification simulations

Abstract Gasping the thermodynamic and phase diagram of the materials being studied is essential for further guiding the development process, like composition design, heat treatment optimization and so on. Nb and Sn are common alloying elements in Ti-based biomedical alloys. In this work, the Ti-Nb-Sn system has been thermodynamically assessed based on experimental phase equilibria. A self-consistent thermodynamic description for the Ti-Nb-Sn system including two ternary compounds Ti 3 Nb 3 Sn 2 and Ti 3 NbSn has been obtained. Based on the comparison between the calculated and experimental phase equilibria, the reliability of the presently obtained thermodynamic description has been verified. The influence of Nb and Sn contents on the precipitation temperature and amount of hcp α -Ti phase in bcc β -(Ti, Nb) has been investigated based on thermodynamic calculations. Results show that the increase of Nb or Sn content in Ti-based alloys would significantly reduce the precipitation amount and transformation temperature of hcp α -Ti phase in bcc β -(Ti, Nb) and the influence of Nb content is more effective than that of Sn. The solidified phases in several as-cast alloys have been thermodynamically predicted based on Scheil solidification simulations. The presently developed thermodynamic description of the Ti-Nb-Sn system can serve as a sub-ternary one in the thermodynamic database for multicomponent Ti-based biomedical alloys.

Peng, Yingbiao↗