Search NASA⌕ Search

SEARCH · Search NASA

Results for “Numerical simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Carbon Dioxide Dispersion in the Combustion Integrated Rack Simulated Numerically

When discharged into an International Space Station (ISS) payload rack, a carbon dioxide (CO2) portable fire extinguisher (PFE) must extinguish a fire by decreasing the oxygen in the rack by 50 percent within 60 sec. The length of time needed for this oxygen reduction throughout the rack and the length of time that the CO2 concentration remains high enough to prevent the fire from reigniting is important when determining the effectiveness of the response and postfire procedures. Furthermore, in the absence of gravity, the local flow velocity can make the difference between a fire that spreads rapidly and one that self-extinguishes after ignition. A numerical simulation of the discharge of CO2 from PFE into the Combustion Integrated Rack (CIR) in microgravity was performed to obtain the local velocity and CO2 concentration. The complicated flow field around the PFE nozzle exits was modeled by sources of equivalent mass and momentum flux at a location downstream of the nozzle. The time for the concentration of CO2 to reach a level that would extinguish a fire anywhere in the rack was determined using the Fire Dynamics Simulator (FDS), a computational fluid dynamics code developed by the National Institute of Standards and Technology specifically to evaluate the development of a fire and smoke transport. The simulation shows that CO2, as well as any smoke and combustion gases produced by a fire, would be discharged into the ISS cabin through the resource utility panel at the bottom of the rack. These simulations will be validated by comparing the results with velocity and CO2 concentration measurements obtained during the fire suppression system verification tests conducted on the CIR in March 2003. Once these numerical simulations are validated, portions of the ISS labs and living areas will be modeled to determine the local flow conditions before, during, and after a fire event. These simulations can yield specific information about how long it takes for smoke and combustion gases produced by a fire to reach a detector location, how large the fire would be when the detector alarms, and the behavior of the fire until it has been extinguished. This new capability could then be used to optimize the location of fire detectors and fire-suppression ports as well as to evaluate the effectiveness of fire suppressants and response strategies. Numerical data collected from these simulations could also be used to develop a virtual reality fire event for crew training and fire safety awareness. This work is funded by NASA's Bioastronautics Initiative, which has the objective of ensuring and enhancing the health, safety, and performance of humans in space. As part of this initiative, the Microgravity Combustion Science Branch at the NASA Glenn Research Center is conducting spacecraft fire safety research to significantly improve fire safety on inhabited spacecraft.

Wu, Ming-Shin↗
NASA NTRS1990

Large eddy simulations and direct numerical simulations of high speed turbulent reacting flows

This research is involved with the implementation of advanced computational schemes based on large eddy simulations (LES) and direct numerical simulations (DNS) to study the phenomenon of mixing and its coupling with chemical reactions in compressible turbulent flows. In the efforts related to LES, a research program to extend the present capabilities of this method was initiated for the treatment of chemically reacting flows. In the DNS efforts, the focus is on detailed investigations of the effects of compressibility, heat release, and non-equilibrium kinetics modelings in high speed reacting flows. Emphasis was on the simulations of simple flows, namely homogeneous compressible flows, and temporally developing high speed mixing layers.

Givi, Peyman↗
NASA NTRS1991

Large eddy simulations and direct numerical simulations of high speed turbulent reacting flows

This research is involved with the implementations of advanced computational schemes based on large eddy simulations (LES) and direct numerical simulations (DNS) to study the phenomenon of mixing and its coupling with chemical reactions in compressible turbulent flows. In the efforts related to LES, a research program was initiated to extend the present capabilities of this method for the treatment of chemically reacting flows, whereas in the DNS efforts, focus was on detailed investigations of the effects of compressibility, heat release, and nonequilibrium kinetics modeling in high speed reacting flows. The efforts to date were primarily focussed on simulations of simple flows, namely, homogeneous compressible flows and temporally developing hign speed mixing layers. A summary of the accomplishments is provided.

Givi, Peyman↗
NASA NTRS1991

Large eddy simulations and direct numerical simulations of high speed turbulent reacting flows

The main objective is to extend the boundaries within which large eddy simulations (LES) and direct numerical simulations (DNS) can be applied in computational analyses of high speed reacting flows. In the efforts related to LES, we were concerned with developing reliable subgrid closures for modeling of the fluctuation correlations of scalar quantities in reacting turbulent flows. In the work on DNS, we focused our attention to further investigation of the effects of exothermicity in compressible turbulent flows. In our previous work, in the first year of this research, we have considered only 'simple' flows. Currently, we are in the process of extending our analyses for the purpose of modeling more practical flows of current interest at LaRC. A summary of our accomplishments during the third six months of the research is presented.

Givi, P.↗
NASA NTRS1992

Large eddy simulations and direct numerical simulations of high speed turbulent reacting flows

The basic objective of this research is to extend the capabilities of Large Eddy Simulations (LES) and Direct Numerical Simulations (DNS) for the computational analyses of high speed reacting flows. In the efforts related to LES, we were primarily involved with assessing the performance of the various modern methods based on the Probability Density Function (PDF) methods for providing closures for treating the subgrid fluctuation correlations of scalar quantities in reacting turbulent flows. In the work on DNS, we concentrated on understanding some of the relevant physics of compressible reacting flows by means of statistical analysis of the data generated by DNS of such flows. In the research conducted in the second year of this program, our efforts focused on the modeling of homogeneous compressible turbulent flows by PDF methods, and on DNS of non-equilibrium reacting high speed mixing layers. Some preliminary work is also in progress on PDF modeling of shear flows, and also on LES of such flows.

Givi, P.↗
NASA NTRS1993

Large eddy simulations and direct numerical simulations of high speed turbulent reacting flows

The primary objective of this research is to extend current capabilities of Large Eddy Simulations (LES) and Direct Numerical Simulations (DNS) for the computational analyses of high speed reacting flows. Our efforts in the first two years of this research have been concentrated on a priori investigations of single-point Probability Density Function (PDF) methods for providing subgrid closures in reacting turbulent flows. In the efforts initiated in the third year, our primary focus has been on performing actual LES by means of PDF methods. The approach is based on assumed PDF methods and we have performed extensive analysis of turbulent reacting flows by means of LES. This includes simulations of both three-dimensional (3D) isotropic compressible flows and two-dimensional reacting planar mixing layers. In addition to these LES analyses, some work is in progress to assess the extent of validity of our assumed PDF methods. This assessment is done by making detailed companions with recent laboratory data in predicting the rate of reactant conversion in parallel reacting shear flows. This report provides a summary of our achievements for the first six months of the third year of this program.

Givi, P.↗
NASA NTRS1993

Large eddy simulation and direct numerical simulation of high speed turbulent reacting flows

The objective of this research is to make use of Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS) for the computational analyses of high speed reacting flows. Our efforts in the first phase of this research conducted within the past three years have been directed in several issues pertaining to intricate physics of turbulent reacting flows. In our previous 5 semi-annual reports submitted to NASA LaRC, as well as several technical papers in archival journals, the results of our investigations have been fully described. In this progress report which is different in format as compared to our previous documents, we focus only on the issue of LES. The reason for doing so is that LES is the primary issue of interest to our Technical Monitor and that our other findings were needed to support the activities conducted under this prime issue. The outcomes of our related investigations, nevertheless, are included in the appendices accompanying this report. The relevance of the materials in these appendices are, therefore, discussed only briefly within the body of the report. Here, results are presented of a priori and a posterior analyses for validity assessments of assumed Probability Density Function (PDF) methods as potential subgrid scale (SGS) closures for LES of turbulent reacting flows. Simple non-premixed reacting systems involving an isothermal reaction of the type A + B yields Products under both chemical equilibrium and non-equilibrium conditions are considered. A priori analyses are conducted of a homogeneous box flow, and a spatially developing planar mixing layer to investigate the performance of the Pearson Family of PDF's as SGS models. A posteriori analyses are conducted of the mixing layer using a hybrid one-equation Smagorinsky/PDF SGS closure. The Smagorinsky closure augmented by the solution of the subgrid turbulent kinetic energy (TKE) equation is employed to account for hydrodynamic fluctuations, and the PDF is employed for modeling the effects of scalar fluctuations. The implementation of the model requires the knowledge of the local values of the first two SGS moments. These are provided by additional modeled transport equations. In both a priori and a posteriori analyses, the predicted results are appraised by comparison with subgrid averaged results generated by DNS. Based on these results, the paths to be followed in future investigations are identified.

Adumitroaie, V.↗
NASA NTRS1982

Calculation of pressure statistics in turbulent free shear flows by direct numerical simulation

Accurate numerical simulations of turbulent free shear flows were performed in order to study the behavior of certain critical turbulence quantities which have been difficult to measure in the laboratory. The three-dimensional time-dependent nonlinear Navier-Stokes equations are solved by the direct numerical simulation technique without turbulence modeling or ad hoc closure assumptions. The pressure interaction terms were factored into diffusion and return-to-isotropy components according to two models. Simulations of the evolution of a turbulent wake with and without swirl present were performed at sufficiently high Reynolds numbers to insure that the flows were strongly nonlinear and turbulent, but low enough so that all scales of motion containing significant energy are adequately resolved. It is noted that the presence of swirl tends to enhance the amplitude of the rms pressure levels.

Metcalfe, R. W.↗
NASA NTRS1987

Numerical simulations of aerodynamic contribution of flows about a space-plane-type configuration

The slightly supersonic viscous flow about the space-plane under development at the National Aerospace Laboratory (NAL) in Japan was simulated numerically using the LU-ADI algorithm. The wind-tunnel testing for the same plane also was conducted with the computations in parallel. The main purpose of the simulation is to capture the phenomena which have a great deal of influence to the aerodynamic force and efficiency but is difficult to capture by experiments. It includes more accurate representation of vortical flows with high angles of attack of an aircraft. The space-plane shape geometry simulated is the simplified model of the real space-plane, which is a combination of a flat and slender body and a double-delta type wing. The comparison between experimental results and numerical ones will be done in the near future. It could be said that numerical results show the qualitatively reliable phenomena.

Matsushima, Kisa↗
NASA NTRS1974

Thermal relaxation of a two dimensional plasma in a dc magnetic field. Part 2: Numerical simulation

The thermal relaxation process for a spatially uniform two dimensional plasma in a uniform dc magnetic field is simulated numerically. Thermal relaxation times are defined in terms of the time necessary for the numerically computer Boltzman H-function to decrease through a given part of the distance to its minimum value. Dependence of relaxation time on two parameters is studied: number of particles per Debye square and ratio of gyrofrequency to plasma frequency.

Hsu, J. Y.↗
NASA NTRS1983

Three-dimensional flow over a conical afterbody containing a centered propulsive jet - A numerical simulation

The supersonic flow field over a body of revolution incident to the free stream is simulated numerically on a large, array processor (the CDC Cyber 205). The configuration is composed of a cone-cylinder forebody followed by a conical afterbody from which emanates a centered, supersonic propulsive jet. The free-stream Mach number is 2, the jet-exit Mach number is 2.5, and the jet-to-free-stream static pressure ratio is 3. Both the external flow and the exhaust are ideal air at a common total temperature. The thin-layer approximation to the time-dependent, compressible, Reynolds-averaged Navier-Stokes equations are solved using an implicit finite-difference algorithm. The data base, of 5 million words, is structured in a 'pencil' format so that efficient use of the array processor can be realized. The computer code is completely vectorized to take advantage of the data structure. Turbulence closure is achieved using an empirical algebraic eddy-viscosity model. The configuration and flow conditions correspond to published experimental tests and the computed solutions are consistent with the experimental data.

Deiwert, G. S.↗
NASA NTRS1984

Three-dimensional flow over a conical afterbody containing a centered propulsive jet: A numerical simulation

The supersonic flow field over a body of revolution incident to the free stream is simulated numerically on a large, array processor (the CDC CYBER 205). The configuration is composed of a cone-cylinder forebody followed by a conical afterbody from which emanates a centered, supersonic propulsive jet. The free-stream Mach number is 2, the jet-exist Mach number is 2.5, and the jet-to-free-stream static pressure ratio is 3. Both the external flow and the exhaust are ideal air at a common total temperature.

Deiwert, G. S.↗
NASA NTRS1984

Direct numerical simulation of curved turbulent channel flow

Low Reynolds number, mildly curved, turbulent channel flow has been simulated numerically without subgrid scale models. A new spectral numerical method developed for this problem was used, and the computations were performed with 2 million degrees of freedom. A variety of statistical and structural information has been extracted from the computed flow fields. These include mean velocity, turbulence stresses, velocity skewness, and flatness factors, space time correlations and spectra, all the terms in the Reynolds stress balance equations, and contour and vector plots of instantaneous velocity fields. The effects of curvature on this flow were determined by comparing the concave and convex sides of the channel. The observed effects are consistent with experimental observations for mild curvature. The most significant difference in the turbulence statistics between the concave and convex sides was in the Reynolds shear stress. This was accompanied by significant differences in the terms of the Reynolds shear stress balance equations. In addition, it was found that stationary Taylor-Gortler vortices were present and that they had a significant effect on the flow by contributing to the mean Reynolds shear stress, and by affecting the underlying turbulence.

Moser, R. D.↗
NASA NTRS1987

Numerical simulation of single and multiple jet interaction within a combustor

Single and multiple jet interaction in a combustor is simulated numerically to determine the effects of various k-epsilon models and boundary conditions as part of an attempt to understand the physics of the flow field inside the preburner of the Space Shuttle Main Engine. Due to the complexity of the physical and chemical phenomena involved, the model is simplified to two dimensions and a single-component nonreacting fluid. The computer code used is the modified TEACH code, which is a steady state isothermal fluid code using the SIMPLE algorithm. The physical validity and numerical accuracy of the model are established through comparisons with experimentally determined isothermal flow fields in a combustor.

Bai, S. Don↗
NASA NTRS1989

The dynamics of charged particles in the near wake of a very negatively charged body - Laboratory experiment and numerical simulation

A numerical simulation that is cylindrical in configuration space and three-dimensional in velocity space has been initiated to test a model for the near-wake dynamics of a very negatively charged body, with reference to the plasma environment around spacecraft. The simulation parameters were closely matched to those of a laboratory experiment so that the results can be compared directly. The laboratory study showed that the electrons and ions can display different temporal features in the filling-in of the wake; and that they can both be found within one body diameter of an object with a highly negative body potential. It was also found that the temperature of the electrons in the very near wake could be somewhat colder than the ambient value, suggesting the possibility of a filtering mechanism being operative there. The simulation results to date largely corroborate the density findings.

Morgan, M. Alvin↗
NASA NTRS1998

An Object Model for a Rocket Engine Numerical Simulator

Rocket Engine Numerical Simulator (RENS) is a packet of software which numerically simulates the behavior of a rocket engine. Different parameters of the components of an engine is the input to these programs. Depending on these given parameters the programs output the behaviors of those components. These behavioral values are then used to guide the design of or to diagnose a model of a rocket engine "built" by a composition of these programs simulating different components of the engine system. In order to use this software package effectively one needs to have a flexible model of a rocket engine. These programs simulating different components then should be plugged into this modular representation. Our project is to develop an object based model of such an engine system. We are following an iterative and incremental approach in developing the model, as is the standard practice in the area of object oriented design and analysis of softwares. This process involves three stages: object modeling to represent the components and sub-components of a rocket engine, dynamic modeling to capture the temporal and behavioral aspects of the system, and functional modeling to represent the transformational aspects. This article reports on the first phase of our activity under a grant (RENS) from the NASA Lewis Research center. We have utilized Rambaugh's object modeling technique and the tool UML for this purpose. The classes of a rocket engine propulsion system are developed and some of them are presented in this report. The next step, developing a dynamic model for RENS, is also touched upon here. In this paper we will also discuss the advantages of using object-based modeling for developing this type of an integrated simulator over other tools like an expert systems shell or a procedural language, e.g., FORTRAN. Attempts have been made in the past to use such techniques.

Mitra, D.↗
NASA NTRS1996

Analysis of Subgrid Eddy Diffusivity in Turbulence Using Direct Numerical Simulation Databases

Direct numerical simulation data in isotropic turbulence at Taylor-scale Reynolds number 90 are used to compute subgrid transfer and spectral eddy diffusivities for passive scalars at Schmidt numbers 1 and 1/8. The results are consistent with spectral transfer processes dominated by a local forward cascade in wavenumber space which is a consequence of moderately nonlocal interactions in the scalar fields. Data decompositions show that resolvable-subgrid interactions make (in general) substantially stronger contributions than fully-subgrid interactions to the eddy diffusivity, which has a non-negligible inverse cascade, or backscatter, component. The eddy diffusivity has a strong cusp at wavenumbers close to the cutoff value separating resolvable and subgrid ranges. At low wavenumbers the eddy diffusivity is generally small, but there the details depend on Schmidt number. The behavior of the subgrid turbulent Schmidt number (the ratio of effective eddy viscosity to eddy diffusivity) is observed to depend strongly on Schmidt number. In interpreting the results at a given spectral cutoff it is important to note that the spectrum of less diffusive scalars (of higher Schmidt number) has more high-wavenumber content.

Yeung, P. K.↗