SEARCH · Search NASA

Results for “Open circuit voltage characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2021

Experimental Data on Open Circuit Voltage Characterization for Li-Ion Batteries

In this article, we present the datasets collected from nine different Li-ion batteries. These datasets contain voltage, current and time measurements during a full charge-discharge cycle of a battery at very low current (that is nearly at �/30 rate). Such low current rate data is suitable for open circuit voltage characterization. The collection of this data was done through the use of an Arbin battery cycler and a thermal chamber was used to control the test temperature. Data were collected over a wide range of temperatures from −25∘C to 50∘C.

Battery management system↗

NASA NTRS1984

Characterization of Open Circuit Voltage and Capacity as a Function of Time

It is noted from the data presented that Li/BCX cells lose approximately 8% of their rated capacity in the first 2 months of storage. After this period of time, little difference is noted in the average realized capacity; however, a significant increase in the range is observed. Over the same period of time the OCV falls at a rate of 0.02V per 1,000 hours. After a period of 8,000 hours the OCV appears stabilize at a value of approximately 3.75V. This may be related to changes in Cl2 concentration due to self-discharge or other reactions. These data indicate that no correlation exists between the reduced open circuit voltage and the realized capacity.

Krehl, P. W.↗

NASA NTRS1976

Studies of silicon p-n junction solar cells

Single crystal silicon p-n junction solar cells made with low resistivity substrates show poorer solar energy conversion efficiency than traditional theory predicts. The physical mechanisms responsible for this discrepancy are identified and characterized. The open circuit voltage in shallow junction cells of about 0.1 ohm/cm substrate resistivity is investigated under AMO (one sun) conditions.

Lindholm, F. A.↗

DOE OSTI2020

Microbial sensor system for the assessment of subsurface environments

A microbial sensor, system, and method that can be used to determine a chemical environment and/or substrate concentrations in anaerobic or aerobic environments, such as soils, sediments and ground waters, are disclosed. An exemplary system uses one or more (e.g., inert) measurement electrodes and a reference electrode. The reference electrode can include an electrode exposed to atmospheric oxygen (e.g., a cathode) or an electrode exposed to stable anaerobic or aerobic conditions. The exemplary microbial sensor system measures open-circuit voltage to characterize the chemical (oxidizing or reducing) environment and/or recovery voltage to measure substrate concentrations in the subsurface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Microbial sensor system for the assessment of subsurface environments

Burge, Scott R.↗

DOE OSTI2024

Contactless Production Testing of Silicon Solar Cells

Critical cost reductions in silicon solar cells are made by minimizing silver usage in their metal contacts. The reason why is both clear and unavoidable—silver is not only expensive, but also a potential limiting resource for scale-up (the PV industry alone used 10.3 % of the global silver supply in 2020 [1]). The result is solar cells with vanishing electrical contact area that are extremely difficult to test prior to module manufacture, when they must be sorted for quality to maximize power output and reliability of the subsequent modules. This project developed a new measurement instrument that enables the transition to solar cells with very low silver content, including cell designs with both minimal busbars and no busbars at all to electrically contact. The resulting instrument at project completion demonstrated the ability to sort cells with comparable—or better—results than existing technology. Compared to existing cell-test instruments, the new tool has minimal contacting requirements, which lowers the maintenance costs and use of consumable parts. We demonstrated innovative, yet pragmatic, solutions for reporting a comprehensive set of measurement results useful for both cell sorting (going forward in the line for module manufacture) and process control (looking backward in the line to identify cell manufacturing issues from wafer to cell-test). In addition to the traditional current-voltage characterization at cell test—short circuit current, open-circuit voltage, power, efficiency and fill factor—the new tool maintains all the advanced parameter characterization of our existing product line such as a substrate doping measurement, carrier recombination (lifetime) analysis, and surface recombination analysis.

14 SOLAR ENERGY↗

DOE OSTI2020

Precursor Reaction Method With High Ga Cu(In,Ga)(S,Se)$_{2}$ to Achieve Increased Open-Circuit Voltage

The precursor reaction process for the fabrication of Cu(In,Ga)Se 2 solar cells potentially allows for low-cost fabrication and scalable processing for manufacturing. Additionally, this process has yielded record efficiencies in lab-scale experiments. Thus far, research on the precursor reaction method has been restricted to relatively low Ga compositions with Ga/(In+Ga) ≈ 25%. By increasing the ratio of Ga, it is possible to increase the bandgap, and thus, increase the open-circuit voltage. This work develops and characterizes the precursor reaction process for use with Ga/(In+Ga) ≈ 50%, with the goal of improving the open-circuit voltage and efficiency. It is shown that with an increased Ga ratio, increased V ∞ is achieved, but the rate of conversion from the precursor to absorber phases is decreased. Additionally, increased Ga improves the film adhesion at increased selenization temperatures as well as improving the film morphology.

14 SOLAR ENERGY↗

NASA NTRS2006

Reliability of Radioisotope Stirling Convertor Linear Alternator

Onboard radioisotope power systems being developed and planned for NASA s deep-space missions would require reliable design lifetimes of up to 14 years. Critical components and materials of Stirling convertors have been undergoing extensive testing and evaluation in support of a reliable performance for the specified life span. Of significant importance to the successful development of the Stirling convertor is the design of a lightweight and highly efficient linear alternator. Alternator performance could vary due to small deviations in the permanent magnet properties, operating temperature, and component geometries. Durability prediction and reliability of the alternator may be affected by these deviations from nominal design conditions. Therefore, it is important to evaluate the effect of these uncertainties in predicting the reliability of the linear alternator performance. This paper presents a study in which a reliability-based methodology is used to assess alternator performance. The response surface characterizing the induced open-circuit voltage performance is constructed using 3-D finite element magnetic analysis. Fast probability integration method is used to determine the probability of the desired performance and its sensitivity to the alternator design parameters.

Shah, Ashwin↗

DOE OSTI2025

The detrimental ratio ( ρ ): A critical metric complementing coulombic loss for long calendar-life silicon-based lithium-ion batteries

Silicon (Si) is a promising high-capacity anode in lithium-ion batteries but suffers from chronic chemical degradation and capacity fading during calendar aging, greatly hindering its automobile applications. Electrolyte engineering currently relies on conventional evaluation criteria of reducing coulombic consumption, which implicitly presume its equivalence to irreversible capacity loss and complicates battery development. Here, we introduce the detrimental ratio p to quantify the fraction of parasitic species that permanently degrades active material. This metric is independent and crucially complements total coulombic consumption for accurate performance evaluation. We systematically investigate multiple electrolyte formulations using high-precision leakage current measurements, open-circuit-voltage experiments, and post-mortem characterizations. Although some electrolytes exhibit similarly low coulombic consumption, they diverge significantly incapacity retention and p. Especially, dimethyl-carbonate-based localized-high concentration electrolyte can synergically achieve low coulombic consumption and detrimental ratio p during calendar aging, owing to its chemically inert and structurally resilient solidelectrolyte interface with minimal isolated Si material. By contrast, increasing fluoroethylene carbonate (FEC) additive content suppresses electrolyte breakdown but suffers aggravated chemical degradation of more LixSi isolation for irreversible capacity loss with arising p. This study critically reveals that the chemistry-characteristic detrimental ratio p establishes physically informed performance evaluation to pave the way for accelerating battery development.

Calendar aging↗

NASA NTRS1977

Measurement of material parameters that limit the open-circuit voltage in P-N-junction silicon solar cells

The greatest gains in solar energy conversion efficiency of p-n-junction silicon solar cells come from increasing the open-circuit voltage V sub OC; it is important to understand and characterize the material parameters that limit the V sub OC. Strong experimental evidence exists to support the assertion that either an anomalously large minority carrier charge storage or an anomalously small minority carrier lifetime in the quasi-neutral emitter region limits the open circuit voltage. A method is presented for measuring charge storage and effective lifetime. Static and transient measurements are analyzed using physical models of the solar cell characteristics. This analysis yields the emitter charge storage and life-time, which then can be related to the various physical mechanisms, such as energy band gap shrinkage, that have been proposed earlier as responsible for limiting V sub OC.

Lindholm, F. A.↗

NASA NTRS1987

Test results of a 60 volt bipolar nickel-hydrogen battery

In July, l986, a high-voltage nickel-hydrogen battery was assembled at the NASA Lewis Research Center. This battery incorporated bipolar construction techniques to build a 50-cell stack with approximately 1.0 A-hr capacity (C) and an open-circuit voltage of 65 V. The battery was characterized at both low and high current rates prior to pulsed and nonpulsed discharges. Pulse discharges at 5 and 10 C were performed before placing the battery on over 1400, 40% depth-of-discharge, low-earth-orbit cycles. The successful demonstration of a high-voltage bipolar battery in one containment vessel has advanced the technology to where nickel-hydrogen high-voltage systems can be constructed of several modules instead of hundreds of individual cells.

Cataldo, Russell L.↗

NASA NTRS1987

Test results of a 60 volt bipolar nickel-hydrogen battery

In July 1986, a high-voltage nickel-hydrogen battery was assembled at the NASA Lewis Research Center. This battery incorporated bipolar construction techniques to build a 50-cell stack with approximately 1.0 A-hr capacity (C) and an open-circuit voltage of 65 V. The battery was characterized at both low and high current rates prior to pulsed and nonpulsed discharges. Pulse discharges at 5 and 10 C were performed before placing the battery on over 1400, 40-percent depth-of-discharge, low-earth-orbit cycles. The successful demonstration of a high-voltage bipolar battery in one containment vessel has advanced the technology to where nickel-hydrogen high-voltage systems can be constructed of several modules instead of hundreds of individual cells.

Cataldo, Robert L.↗

DOE OSTI2024

Impedance sources (Z sources) with inherent fault protection for resilient and fire-free electricity grids

Modern societies would not survive without electricity and at the same time electrical faults could cause and have caused many catastrophes—mainly deadly fires—to our societies. There are two types of electricity sources: the voltage source such as generators, charged batteries and capacitors, and the current source such as charged inductors, current-regulated rectifiers, and superconducting magnetic energy storage. An “ideal” voltage source—that is often-sought-or-intentionally engineered—generates a constant voltage irrespective of its load current, and an “ideal” current source injects a constant current irrespective of its load voltage. However, two problems exist: (1) voltage or current sources do not represent many emerging natural/renewable energy sources such as wind turbine generators, photovoltaic cells, and fuel cells, whose output voltage and current are strongly dependent on each other, and (2) a short-circuit fault to an artificially-made and controlled “ideal” voltage source or an open-circuit fault to an “ideal” current source can cause catastrophic failures of the source itself and its surrounding circuits due to large (theoretically infinite) short-circuit current or open-circuit voltage. Here we introduce an impedance source concept to represent, characterize, and model those electricity sources whose output voltage and current are strongly dependent on each other. First, we found that many electric sources with no feedback (or active) control of their output voltage and/or current are a natural impedance source with inherent fault protection at short-circuit or open-circuit faults. Second, any electrical source can be artificially controlled to mimic a natural impedance source. Finally, we show how to apply natural impedance sources and nature-mimicking artificially-controlled sources to the electricity grid—the most complex machine ever made by human beings—to realize electricity grids that are naturally stable, self-protected against electrical faults, and resilient to natural and human-made events.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2024

The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells

Electrode cracks in polymer electrolyte membrane fuel cells (PEMFCs) are correlated with early onset failures. Here, in this work we investigate the influence of cracked gas diffusion electrodes (GDEs) on the durability of the membrane electrode assembly (MEA) using a combined chemical-mechanical accelerated stress test (AST). Electrode crack dimensions were systematically tuned using ink formulations and material selection strategies. A parameter to describe the crack width areal density (Φ CW ) was used to quantify the degree of discontinuity in the electrode surfaces. Open circuit voltage (OCV) transient analyses were used to benchmark and characterize the failure mechanisms in the MEAs as a function of the Φ CW . While smaller electrode-level cracks, on the order of microns, yielded a 28 % decrease in operating lifetime, larger cracks that propagated from a discontinuous, microporous layer (MPL) coating, decreased the operating lifetime by 56 %. This work emphasizes the need for material processing strategies that consider defect tolerances to limit membrane failures in PEMFCs.

08 HYDROGEN↗

DOE OSTI2023

Critical Contribution of Imbalanced Charge Loss to Performance Deterioration of Si-Based Lithium-Ion Cells during Calendar Aging

Increasing the energy density of lithium-ion batteries, and thereby reducing costs, is a major target for industry and academic research. One of the best opportunities is to replace the traditional graphite anode with a high-capacity anode material, such as silicon. However, Si-based lithium-ion batteries have been widely reported to suffer from a limited calendar life for automobile applications. Heretofore, there lacks a fundamental understanding of calendar aging for rationally developing mitigation strategies. Both open-circuit voltage and voltage-hold aging protocols were utilized to characterize the aging behavior of Si-based cells. Particularly, a high-precision leakage current measurement was applied to quantitatively measure the rate of parasitic reactions at the electrode/electrolyte interface. The rate of parasitic reactions at the Si anode was found 5 times and 15 times faster than those of LiNi 0.8 Mn 0.1 Co 0.1 O 2 and LiFePO 4 cathodes, respectively. Here, the imbalanced charge loss from parasitic reactions plays a critical role in exacerbating performance deterioration. In addition, a linear relationship between capacity loss and charge consumption from parasitic reactions provides fundamental support to assess calendar life through voltage-hold tests. These new findings imply that longer calendar life can be achieved by suppressing parasitic reactions at the Si anode to balance charge consumption during calendar aging.

25 ENERGY STORAGE↗

DOE OSTI2025

ZnTiN 2 as an Electron-Selective, Protective Layer on Si Photocathodes

Photoelectrochemical production of fuels requires photoelectrodes that efficiently convert sunlight to electrochemical energy by producing photovoltage and photocurrent and maintain this ability over time under a variety of pH, illumination, and applied bias conditions. Work in the photovoltaic community has demonstrated that interfaces with high charge carrier selectivity provide high photovoltages. This offers a co-design opportunity to create semiconductor photoelectrodes with contact layers that are both carrier-selective and offer protection from degradation in aqueous solutions. In this work, we explored the ternary nitride ZnTiN 2 as an electronselective, protective layer for Si-based photocathodes. We demonstrated that ZnTiN 2 formed a heterojunction with p-type Si that facilitated electron movement toward the ZnTiN 2 surface for light-driven reduction reactions. Across a variety of electrolyte conditions, ZnTiN 2 /Si produced an open circuit voltage of ca. 400 mV vs the solution potential, while bare Si produced 220−480 mV vs the solution potential depending on conditions. ZnTiN 2 was also shown to protect Si over 72 h at open circuit in the dark in 0.1 M KHCO 3 aqueous solution at pH 10.5, with a 2.4% loss in open circuit voltage compared to a 17% loss for unprotected Si. A protective effect was also observed under illumination during methyl viologen reduction at pH 3.5 for 21 h, with a 2.5% loss in open circuit voltage observed for ZnTiN 2 /Si compared to a 25% loss in open circuit voltage for unprotected Si under the same conditions. Elemental characterization revealed the presence of oxides on the surface of ZnTiN 2 that are consistent with the Pourbaix diagram after photoelectrochemical operation; these oxides appeared to support durability without hindering charge carrier extraction to drive electrochemical work. This work highlights the promise of ZnTiN 2 for durable photoelectrochemical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1975

Studies of silicon PN junction solar cells

Silicon pn junction solar cells made with low-resistivity substrates show poorer performance than traditional theory predicts. The purpose of this research was to identify and characterize the physical mechanisms responsible for the discrepancy. Attention was concentrated on the open circuit voltage in shallow junction cells of 0.1 ohm-cm substrate resistivity. A number of possible mechanisms that can occur in silicon devices were considered. Two mechanisms which are likely to be of main importance in explaining the observed low values of open-circuit voltage were found: (1) recombination losses associated with defects introduced during junction formation, and (2) inhomogeneity of defects and impurities across the area of the cell. To explore these theoretical anticipations, various diode test structures were designed and fabricated and measurement configurations for characterizing the defect properties and the areal inhomogeneity were constructed.

Lindholm, F. A.↗

DOE OSTI2021

Low-Cost Handle Study for Photovoltaics on Transfer Printed Virtual Substrates

This work expands upon previous research related to transfer printed virtual substrates: a technique for generating low-cost engineered substrates that is not based on wafer reuse. Here, silicon and sapphire are evaluated as candidate low-cost handle materials, validated by metal organic chemical vapor deposition regrowth of GaAs single-junction solar cells. Resulting devices are studied via materials and electrical characterization techniques, including concentration measurements that indicate GaAs//sapphire TPVS open-circuit voltage at >10 suns comparable with identical devices grown on a prime GaAs substrate.

41 EE - Solar Energy Technologies Office (EE-4S)↗