Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxidation Penetration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Oxidation Penetration in Nuclear Graphite

Study results are presented for seven grades of graphite where 21 cylindrical samples were oxidized to a nominal level of mass loss. Low mass loss samples exhibited ~3% oxidative mass loss, intermediate ~8%, and high ~11%. Flat sample surfaces were covered during oxidation to minimize oxidation penetration at the top and bottom of each sample. Oxidized samples had their diameters reduced stepwise in 1 mm or 2 mm increments. Residual samples were weighed, geometric dimensions were recorded, and Archimedes measurements were taken at each step. Preliminary comparative graphical analysis is presented to illustrate the resultant density gradients observed. Raw tabular data are also provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Deformation band corrosion as a result of applied stress and cold-work in 304 stainless steel in simulated pressurized water reactor primary water conditions

Stainless steels like 304SS are commonly used in pressurized water reactor primary water environments due to their excellent resistance to stress corrosion cracking (SCC). However, SCC susceptibility has been observed in cold-worked 304SS. Cold-rolling introduces a high density of defects, such as deformation bands or dislocations, into the microstructure; applied stress, even if macroscopically below the yield stress, can result in regions with high localized stresses. Cold-worked and non-cold-worked samples were exposed to 360 °C simulated PWR primary water for 1500 h with and without active loading. Corrosion susceptibility of dislocations and deformation bands induced by cold-rolling and/or applied stress was studied using high-resolution (analytical) transmission electron microscopy. Deformation bands were generated in all specimens examined in the study. Penetrative oxidation was observed in some deformation bands in each specimen. The depth of penetrative deformation band oxidation frequently exceeded the depth of grain boundary oxidation in all specimens. However, deformation band oxides generally were narrowly confined to the deformation band plane. Highly Ni-rich regions were observed beyond all oxidation fronts. Surface oxides were thicker in the specimens exposed under active loading. In conclusion, the implications of these findings at surfaces for deformation bands intersecting stress corrosion crack paths are discussed.

EFTEM↗
DOE OSTI2024

Graphite Oxidation Activities

Graphite Oxidation Activities to include introduction, rate determination, strength after oxidation, penetration depth analysis, strategic partnership projects, and summary and continuing work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Corrosion analysis of Al-Ce-Ni and Al-Cu-Ce cast alloys in dilute boric acid at room and elevated temperatures

Two Al-Ce-Ni cast alloys, and an Al-Cu-Ce cast alloy, as candidate wet storage materials for spent nuclear fuels, were tested in 0.23 wt% H 3 BO 3 solution to assess the alloy corrosion resistance. Electrochemical and gravimetric corrosion data suggest that the three Al alloys are unlikely to undergo any severe corrosion in dilute H 3 BO 3 at or below 50 °C. Post-exposure characterization of the three Al alloys, including scanning and transmission electron microscopy and electron dispersive spectroscopy, revealed a corrosion product layer, mostly Al 2 O 3 , on the exposed surface and local penetration of oxygen into the alloy matrix. The degree of oxide layer growth and oxygen penetration is greater at 80 °C than the temperature at/below 50 °C. The Al-Cu-Ce alloy is considered less corrosion resistant than the other two alloys studied.

Al-Ce alloy↗
DOE OSTI2026

Elucidating the impact of stress states on grain boundary passivation in Ni-5Cr using the Rhines pack method

The oxidation behavior of a Ni–5Cr (at.%) alloy was evaluated at 420 ° C using the Rhines pack method and simultaneous tensile and compressive stress states via a miniature four-point bending fixture. At this moderate temperature, grain boundaries dominate mass transport and the resulting oxidation response. Oxidation produced approximately 1μ⁢m-wide protective Cr 2 O 3 films capping some grain boundaries and penetrative, intergranular Cr-rich oxides at other grain boundaries. Externally applied tensile and compressive stress during oxidation increased the prevalence of Cr 2 O 3 cap formation compared to no applied stress, with tensile stress resulting in more Cr 2 O 3 caps than compressive stress. The observed oxide cap morphology was similar across all test conditions. Regions under compressive stress showed an order of magnitude greater Cr depletion depth along the grain boundary. Chromium nitrides (CrN), likely from N contamination of the Rhines pack cell, were observed both at the oxide–metal interface and intergranularly within the alloy. Collectively these results demonstrate that applied stress promotes localized protective oxide cap formation over grain boundaries, with compressive stress additionally promoting deeper Cr depletion. Furthermore the experimental approach helped separate out the effects of stress on local oxide formation and grain boundary passivation.

4 point bend↗
DOE OSTI2025

Sustainable upcycling of polyethylene waste to compatibilizers and valuable chemicals

Controllable functionalization of polyethylene (PE) waste could generate new polymeric materials that are generally difficult to manufacture sustainably while also addressing the growing plastics waste problem. However, these modifications remain challenging due to the inherent stability of the PE backbone. Non-thermal atmospheric plasma enables molecular activation under mild conditions while utilizing renewable energy but is primarily employed for surface modification, as plasmas do not penetrate the bulk of materials. Herein, controllable bulk oxidative functionalization of PE wax (PEW) and low-density PE (LDPE) of varying molecular weights was achieved, with up to 6 mol% oxygen incorporation, by manipulating melt viscosity. This functionalization was accomplished either through temperature adjustment or by introducing a melt viscosity modifier, removable via simple extraction methods, to reduce LDPE viscosity, enhance diffusion and chain mobility, and enable bulk oxidation. The oxidized LDPE induces compatibilization in blends of poly(lactic acid) (PLA) and LDPE with improved interfacial adhesion and mechanical properties, such as a 70% increase in elongation-at-break values vs. the control. These findings pave the way for catalyst-free upcycling of direct plastics waste and plastics waste-derived products, enabling the creation of high-value products across various markets.

Plastic upcycling↗
DOE OSTI2025

Chromium segregation-induced oxide evolution in Ni-10Cr alloys during high-temperature oxidation

The oxidation behavior of a Ni-10(wt%)Cr alloy under high-temperature O 2 conditions is investigated using transmission electron microscopy and first-principles calculations. Results reveal that chromium segregation plays a central role in driving the evolution of complex oxide phase structures during oxidation. At low Cr concentrations, Cr preferentially segregates to NiO grain boundaries or internal pores, substituting for Ni atoms and forming Ni(Cr)O solid solutions. As Cr content increases, enhanced diffusion promotes Cr penetration into the NiO lattice, leading to the formation of multiphase oxide structures. First-principles modeling corroborates these findings: at low Cr concentrations, Cr atoms favor surface and grain-boundary segregation, while higher concentrations lead to Cr aggregation within the NiO bulk. Furthermore, the integrated experimental-theoretical approach provides atomistic insights into Cr-mediated mass transport mechanisms during alloy oxidation and offers valuable guidance for controlling oxide growth kinetics and phase stability in Ni-Cr alloys, with implications for improving oxidation resistance in high-temperature structural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Market optimization and technoeconomic analysis of hydrogen-electricity coproduction systems

Decarbonization efforts across North America, Europe, and beyond rely on variable renewable energy sources such as wind and solar, as well as alternative fuels, such as hydrogen, to support the sustainable energy transition. These advancements have prompted a need for more flexibility in the electric grid to complement non-dispatchable energy sources and increased demand from electrification. Integrated energy systems are well suited to provide this flexibility, but conventional technoeconomic modeling paradigms neglect the time-varying dynamic nature of the grid and thus undervalue resource flexibility. In this work, we develop a computational optimization framework for dynamic market-based technoeconomic comparison of integrated energy systems that coproduce low-carbon electricity and hydrogen (e.g., solid oxide fuel cells, solid oxide electrolysis) against technologies that only produce electricity (e.g., natural gas combined cycle with carbon capture) or only produce hydrogen. Our framework starts with rigorous physics-based process models, built in the open-source Institute for the Design of Advanced Energy Systems (IDAES) modeling and optimization platform, for six energy process concepts. Using these rigorous models and a workflow to optimally design each technology, the framework is shown to be capable of evaluating new and emerging technologies in varying energy markets under a plethora of future scenarios (i.e., renewables penetration, carbon tax, etc.). Ultimately, our framework finds that solid oxide fuel cell-based coproduction systems achieve positive profits for 85% of the analyzed market scenarios. From these market optimization results, we use multivariate linear regression (R 2 values up to 0.99) to determine which electricity price statistics are most significant to predict the optimized annual profit of each system. The proposed framework provides a powerful tool for directly comparing flexible, multi-product energy process concepts to help discern optimal technology and integration options.

08 HYDROGEN↗
DOE OSTI2024

Oxide dissolution and oxygen diffusion scenarios in niobium and implications on the Bean–Livingston barrier in superconducting cavities

We generalize a native Nb2O5 dissolution model [G. Ciovati, Appl. Phys. Lett. 89, 022507 (2006)] to sequential overlayer dissolutions, multilayer dissolution, and realistic temperature profiles, which may be applicable to other materials. The model is applied to secondary ion mass spectrometry depth profile measurements for varying temperature profiles and two-step oxide dissolution in Nb and found to agree well. In the context of the Meissner screening response due to impurity profiles on the length scale of the London penetration depth, the shallow diffusion of O impurities results in a substantial decrease in the peak supercurrent density near the surface. In this framework, oxide dissolution and oxygen diffusion can account for a rise in peak supportable magnetic field in SRF cavities with baking time and a suppression after the optimal baking time is reached, in good agreement with peak-field baking temperatures and times as well as recent quench field measurements.

Lechner, Eric↗
DOE OSTI2025

Precise Linker Length and Dynamic Bond Exchange Control Penetrant Diffusion in Dense Vitrimers

Polymer networks with dynamic covalent bonds have been investigated for their self-healing ability, recyclability, and potential as more sustainable materials. Recent results have indicated that in some cases, bond exchange can enhance the transport of penetrants in dense networks, pointing to their potential for separations of membranes. Here, imine dynamic bonds in ethylene oxide (EO) networks with precise linker lengths were synthesized to investigate the transport of N,N′-bis(2,5-di-tert-butylphenyl)-3,4,9,10-perylenedicarboximide (BTBP), a large, anisotropic dye molecule. Networks with mesh sizes smaller than, comparable to, and greater than the size of the penetrant axes were investigated to probe the effects of bond exchange and network confinement on transport. Mesh sizes, which ranged from 0.5 to 1.62 nm, were determined from shear rheology, glass transitions by calorimetry, and probe diffusion coefficients by fluorescence recovery after photobleaching. Permanent networks with identical EO chain lengths were prepared as control samples, and up to a 3 orders of magnitude increase in diffusion coefficient is observed in the dynamic systems for short linkers containing 13 backbone atoms. The longest linkers with 71 backbone atoms show no difference between the permanent and dynamic networks. Linkers shorter than 11 backbone atoms, corresponding to a mesh size smaller than the penetrant small axis, diffusion is no longer observable on the experimental time scale, indicating a sharp cutoff attributed to the precise linkers and narrow mesh size distribution. The dynamic imine exchange time scales were compared to the diffusive hopping times of penetrants and indicate that exchange can occur during a diffusive displacement. Furthermore, these findings provide insights into the factors affecting penetrant transport in dense polymers and inspire the development of next-generation selective polymer membranes.

Diffusion↗
DOE OSTI2024

Towards a quantitative understanding of bonding in supersonic single particle impacts: A three-dimensional FIB-SEM exploration

Particle bonding is crucial to coating quality in cold spray, but it has been a challenge to accurately quantify bonding even in single particle impacts. This paper uses FIB-SEM to explicitly map the particle-substrate interface for Cu-on-Cu single microparticle impacts in a full 3D rendering that spans a wide range of impact velocities. This approach permits a detailed quantification of the total bonding area and all of its associated components. In addition to revealing why prior 2D characterization efforts have missed important details about impact bonding, these data quantitatively reveal the evolution of bonding from its onset at the “critical velocity” V cr (where bonding is generally poor, ∼6 %) to its peak at around 1.3‧V cr (where almost 90 % of the particle bonds). Further increase in the velocity to 1.5‧V cr and beyond finds the onset of hydrodynamic penetration and a decrease in bonding. These data then support the development of a simple analytical model based on oxide rarefication and extrusion of bare metal through gaps in the oxide layer as driving the development of bonding. As a result, the model reproduces the experiments and provides guidance on optimization of bonding as a function of material and process parameters.

Analytical methods↗
DOE OSTI2026

Oxide nucleation via threshold-driven volume instability in Ni oxidation

Oxide nucleation dictates the onset of metal oxidation, yet the atomistic pathways bridging initial oxygen adsorption to bulk phase transformation remain elusive. Here, we utilize in-situ atomic-resolution imaging to directly capture the nucleation of nickel oxide, revealing a threshold-driven, cooperative transformation of Ni into NiO. Our observations identify a distinct incubation period during which oxygen progressively accumulates in subsurface layers. Once a critical concentration and penetration depth are reached, a collective lattice reconfiguration is triggered, abruptly converting multiple Ni layers into NiO. Atomistic simulations corroborate this mechanism, identifying a cooperative lattice instability induced by subsurface oxygen saturation. These results establish subsurface oxygen incorporation as the missing mechanistic link between surface adsorption and three-dimensional oxide formation, providing an atomistic framework to understand and control reactive phase transformations in materials synthesis, catalysis, and degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Speciation and diffusive dynamics in hydrated grain boundaries of complex oxide Gd2Ti2O7

Abstract Grain boundaries in polycrystalline materials significantly affect their properties, such as ionic transport, corrosion, and chemical durability. The pyrochlore compound (Gd 2 Ti 2 O 7 ) is employed as a model for complex oxides and is known for its diverse applications, including nuclear waste immobilization. Density functional theory-based first-principles molecular dynamics simulations were performed at different temperatures on the hydrated grain boundary system. The results show extensive transformations within the grain boundaries among hydrous water species (OH − , H 2 O, and H 3 O + ). The temperature dependence of self-diffusion coefficients follows Arrhenius behavior, with an activation energy of 35.9 kJ/mol for hydrogen and 46.3 kJ/mol for oxygen. The lifetime of OH − is about three to four times longer than that of H 2 O at temperatures from 800 to 2100 K, suggesting the greater stability of OH − over H 2 O, a unique characteristic of the grain boundaries. The estimated lifetime of the hydrous species decreases as the temperature increases, with an activation energy of 9.9 kJ/mol for OH − and 13.4 kJ/mol for H 2 O. While Gd 3 + is more mobile than Ti 4+ , both the Gd 3 + and Ti 4+ cations are orders of magnitude less mobile than the water species. The results suggest that water species are much more mobile within grain boundaries than in the bulk crystal and have the potential to penetrate deep into polycrystalline materials through grain boundaries, leading to grain boundary degradation and dissolution. The different mobilities of cations in complex oxides can lead to leaching of certain cations and incongruent dissolution during the chemical weathering of Earth and industrial materials.

B. Ghosh, Dipta↗
DOE OSTI2024

Dielectric and magnetic properties of microwave-absorbing FeAl x O y catalysts fabricated via solution combustion synthesis

Iron-based alumina (FeAl x O y ) nanocomposites are microwave-absorbers and catalysts, which makes them promising for emerging microwave-assisted thermocatalytic technologies. Solution combustion synthesis (SCS) has been used to synthesize FeAl x O y powders, and prior work has demonstrated that adjusting SCS parameters significantly changes phase composition and specific surface area of the products. However, it is unclear how synthesis parameters affect their microwave-absorbing properties, which are essential for optimizing microwave-assisted technologies. To address this challenge, in the present work, twelve different FeAl x O y products were synthesized at different combinations of the SCS parameters such as two fuels (citric acid and glycine), two heating modes (hotplate and muffle furnace), and three Fe:Al molar ratios (2:1, 1:1, 1:2). Dielectric and magnetic properties of the products were characterized using a network analyzer and a vibrating sample magnetometer. Based on the measured permittivity and permeability, penetration depth and reflection loss were calculated as a function of frequency and bed thickness. The products were heated by microwaves at 2.45 GHz and then examined with X-ray diffraction (XRD) analysis. For all products, the magnetic saturation was lower than for bulk iron oxides because of the small crystallite size and aluminum substitution. The use of glycine induced high dielectric losses and enabled fast microwave-heating rates compared to citric acid. Higher Fe:Al ratio also led to higher dielectric and magnetic losses. With glycine fuel, SCS in a furnace induced larger penetration depth and lower microwave absorption than SCS on a hotplate. The minimization of reflected power was more sensitive to the thickness of the product bed than to the frequency of the electromagnetic field. Post-heating XRD analysis revealed different phase transformations in the FeAl x O y powders depending on the SCS parameters. As a result, an FeAl x O y material, synthesized via incipient wetness impregnation, lacked magnetic losses and did not heat well as compared to the SCS products.

Combustion synthesis↗
DOE OSTI2025

Computational Modeling of Molten Salt Infiltration and Oxidation in Nuclear Graphite

Graphite is utilized as a moderator and reflector in advanced nuclear reactor designs due to its high thermal conductivity, neutron moderation properties, and resistance to radiation damage. However, its longterm performance and reliability are challenged by degradation mechanisms such as molten salt infiltration in molten salt reactors (MSRs) and oxidation in gas-cooled reactors (GCRs). These mechanisms can compromise the structural integrity and operational lifetime of graphite components, necessitating a more detailed assessment of their physical behavior. This report focuses on the development of computational models for molten salt infiltration and oxidation of graphite to aid the design and performance analysis of graphite components. For molten salt infiltration, a computational framework is developed that couples incompressible Navier-Stokes and phase-field model to simulate the penetration of molten salt into graphite?s interconnected pore structure. Initial model verification is performed using two-phase flows in two dimensions, demonstrating the models ability to capture fundamental physical behavior and agree with analytical solution. This framework is then applied to a realistic IG110 nuclear graphite , where a computed tomography extracted pore geometry is used to analyse the infiltration behavior of FLiNaK molten salt. This model provides insights into how the microstructure and other relevant parameters influence the transport pathways of molten salt into graphite, potentially offering a means to rapidly evaluate a graphite grade?s resistance to infiltration. For oxidation, the report details pore-scale mass and heat transport models, describing the diffusion of gases, reaction kinetics, and thermal effects. Additionally, this report highlights inconsistencies in the existing volume-averaged macroscopic model, particularly in upscaling of reaction kinetics and flux terms, and surface to volume transformations. These inconsistencies suggest that current formulations may not accurately capture the experimentally observed graphite oxidation process, highlighting the need for improved model development. This work advances the development of physics-based computational models for graphite degradation, contributing to improved predictive models for next-generation nuclear reactor designs. Future efforts will focus on refining the infiltration model to address non-physical behaviors and enhance its robustness. Additionally, for oxidation, further studies will employ the principles of volume averaging to rigorously derive the upscaled equations, potentially in collaboration with subject matter experts.

Computational Modeling of Molten Salt Infiltration↗
DOE OSTI2026

Electrospun Ti–Zr Oxide Heterostructures Enable Strongly Anchored Ultralow-Ir Anodes for Durable Acidic Oxygen Evolution

Proton-exchange-membrane water electrolysis (PEMWE) requires acidic oxygen-evolution-reaction (OER) anodes that combine high activity, high durability, and low Ir loading. Here, we report a Ti-Zr composite electrospun oxide (ESO) nanorod support that enables ultralow-Ir anodes for high-performance PEMWE. Zr-containing Ti oxide heterostructures stabilize anatase-rich TiO2, tune the local oxygen-coordination environment, and strengthen interfacial anchoring of IrOx under acidic anodic conditions. The electrospun nanorod network further creates an open, mechanically coherent catalyst layer that improves Ir utilization, ionomer penetration, and mass transport. At an anode loading of 0.2 mgIr cm-2, the optimized Ir/TiZr20-ESO anode delivers a PEMWE mass activity of 0.99 A mgIr-1 at 1.45 V, 28.3 and 43.0 times higher than commercial Ir black and commercial IrO2/TiO2, respectively. The same anode reaches 3.0 and 4.0 A cm-2 at 1.75 and 1.83 V, respectively, and sustains 2000 h operation at 2.0 A cm-2. Also, accelerated stress tests up to 525 hours over 31,500 cycles confirm promising long-term durability, with an insignificant performance decay of 0.4 μV per cycle. Density functional theory indicates that the Ti-Zr oxide heterostructure suppresses Ti demetallation and strengthens IrO2 interfacial binding, rationalizing the improved high-current-density stability.

25 ENERGY STORAGE↗
DOE OSTI2023

Nonlinear Loss Engineering in Near‐Zero‐Index Bulk Materials

Transparent conducting oxides (TCOs) show unprecedented optical nonlinearities in the near infrared wavelength range, where the real part of their linear refractive index approaches zero. More specifically, the Kerr nonlinearities of these materials have sparked widespread attention due to their magnitude and speed. However, due to the absorptive nature of these nonlinear processes, it is of fundamental interest to further investigate the imaginary component of the nonlinear index. The present work studies the nonlinear optical absorption properties of aluminium‐doped zinc oxide (AZO) thin films in their near‐zero‐index (NZI) spectral window. It is found that the imaginary part of the refractive index is reduced under optical excitation such that the field penetration depth more than doubles. An optically induced shift of the NZI bandwidth of ≈120 nm for a pump intensity of 1.3 TW cm −2 is also demonstrated. Looking into the optically induced spectral redistribution of the probe signal, local net gain is recorded, which is ascribed to a nonlinear adiabatic energy transfer. The present study adds key information about the fundamental interplay between real and imaginary nonlinear indices in NZI media, while advancing parametric amplification as viable direction for loss compensation.

36 MATERIALS SCIENCE↗