SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Metallic Pd and/or reduced Pd oxide on Pd–TiO 2 is found to be the intrinsic active site for O 2 removal.
Molten chloride salts (including MgCl 2 , KCl, NaCl, and ZnCl 2 ) are being considered for heat transfer media for renewable (solar) and nuclear power generators, as fuel carrier for nuclear reactors, and as thermal energy storage media. Impurities such as oxygen, hydroxides, moisture, and sulfur are known to negatively influence the corrosion of materials in contact with the salt (e.g., structural metals). Commercially available chloride salts come with a range of impurities. Before using the chloride salts at high temperature, it is desirable to remove the impurities to increase the performance of the salt and reduce corrosion. In this study, we tested the use of thionyl chloride vaporized into a stream of argon to react with oxygenated impurities in a mixture of MgCl 2 -KCl-NaCl, removing them as HCl and SO 2 . The reagent was bubbled through the salt when both above and below the melting point. The reaction was followed using thermocouple data from the salt and by Fourier transform infrared (FTIR) spectroscopy on the exhaust of the reactor. The reaction kinetics were followed by comparing the peaks from SO 2 product to SOCl 2 reagent in the FTIR spectra. The purity of the salt was assessed at the end of the purification process by x-ray diffraction and inductively coupled plasma analysis. Although the process was effective in removing the oxygen content of the mixture, ternary compounds were formed in the process, including KNiCl 3 and KMgCl 3 . The nickel in KNiCl 3 came from the reaction between the salt and the nickel vessel. Thus, these experiments suggest that improvements to the process must be made before using SOCl 2 vapors for the purification of chloride salts.
Here this work reports an efficient method for facile synthesis of hierarchically porous carbon (WB-AC) utilizing wheat bran waste. Obtained carbon showed 2.47 mmol g -1 CO 2 capture capacity with good CO 2 /N 2 selectivity and 27.35 to 29.90 kJ mol -1 isosteric heat of adsorption. Rapid removal of MO dye was observed with a capacity of ~555 mg g -1 . Moreover, WB-AC demonstrated a good OER activity with 0.35 V low overpotential at 5 mA cm -2 and a Tafel slope of 115 mV dec -1 . It also exhibited high electrocatalytic HER activity with 57 mV overpotential at 10 mA cm -2 and a Tafel slope of 82.6 mV dec -1 . The large SSA (757 m 2 g -1 ) and total pore volume (0.3696 cm 3 g -1 ) result from N 2 activation contributing to selective CO 2 uptake, high and rapid dye removal capacity and superior electrochemical activity (OER/HER), suggesting the use of WB-AC as cost effective adsorbent and metal free electrocatalyst.
Oxy-combustion systems result in enriched CO 2 in exhaust gases; however, the utilization of the concentrated CO 2 stream from oxy-combustion is limited by remnant O 2 . CH 4 oxidation using Pd catalysts has been found to have high O 2 -removal efficiency. Here, in this study, the effect of excess CO 2 in the feed stream on O 2 removal with CH 4 oxidation is investigated by combining experimental and theoretical approaches. Experimental results reveal complete CH 4 oxidation without any side-products, and a monotonic increase in the rate of CO 2 generation with an increase in CO 2 concentration in the feed stream. Density-functional theory calculations show that high surface coverage of CO 2 on Pd leads to a reduction in the activation energy for the initial dissociation of CH 4 into CH 3 and H, and also the subsequent oxidation reactions. A CO 2 -rich environment in oxy-combustion systems is therefore beneficial for the reduction of oxygen in exhaust gases.
Not Available
The redox properties of Fe 3 O 4 surfaces are central to many catalytic processes and enable dynamic, reduction-induced morphological restructuring during reactions. Here, we investigate the structural changes of the Fe 3 O 4 (001) surface during the decomposition of formic and acetic acids using scanning tunneling microscopy, X-ray photoelectron spectroscopy, and density functional theory (DFT) calculations. Both acids readily deprotonate, forming ordered carboxylate overlayers on the surface. Product formation pathways involve the removal of lattice oxygen, resulting in extensive surface restructuring. For formic acid, only a modest level of surface oxygen removal (∼3%) is observed, resulting in elongated pits along the octahedral Fe rows and exhibiting an aspect ratio of ∼3. In contrast, acetic acid induces more extensive reduction, with the removal of ∼20% of surface oxygen, yielding significantly larger pits while maintaining a similar aspect ratio. Repeated exposure to acetic acid further enlarges the pits, indicating preferential etching at step edges. DFT calculations reveal a mechanistic sequence in which lattice oxygen removal destabilizes adjacent Fe atoms, promoting their migration into the bulk and subsequent pit propagation and step edge formation. Together, these findings provide atomistic insights into the coupling between carboxylic acid conversion and oxide surface restructuring, underscoring the strong interplay between redox chemistry and morphological changes on catalytically active Fe 3 O 4 surfaces.
Flue gas purification is important for pressurized oxy-combustion systems to produce pure carbon dioxide (CO 2 ) streams ready for storage or utilization. A catalytic approach to removing oxygen (O 2 ) impurities from pressurized oxy-combustion flue gas via reduction with methane (CH 4 ) was investigated in this work. Two types of catalysts were studied: palladium (Pd)-based catalysts supported on titania (TiO 2 ) prepared by incipient wetness impregnation and cobalt–manganese (CoMn) composite catalysts prepared by coprecipitation. The performance of the catalysts was evaluated in a high-pressure–high-temperature, fixed-bed reactor at a pressure of 15 bar and a gas hourly space velocity of 30 000 h –1 (standard conditions), with a simulated feeding gas composed of 3 vol % O 2 , 1.5 vol % CH 4 , and CO 2 as the balance gas. Among the Pd catalysts, 5% Pd/TiO 2 achieved the maximum 86% O 2 removal at ≥350 °C. The CoMn oxide catalysts displayed comparable or better activities for O 2 reduction compared with the Pd catalysts. Among them, the Co 40 Mn 1 catalyst exhibited the best performance, able to reduce 99.9% of O 2 impurities at ~370 °C with negligible carbon monoxide (CO) formation (<10 ppmv). Both trivalent and divalent Co and Mn were detected on the catalyst surface, and the superior activity of Co 40 Mn 1 might be associated with the resultant disordered structure. Furthermore, the activity of the catalyst was not affected by the presence of a trace amount of nitric oxide (NO) gas contaminant. Results of this study provide the basis for scale-up studies in both the synthesis and performance of non-noble metal catalysts.
Palm oil, one of the most widely used vegetable oils, offers significant potential as a sustainable feedstock for biofuel production. This study explores the deoxygenation of palm oil using glycerol as a hydrogen donor, with nickel-molybdenum (NiMo) catalysts supported on commercial alumina (Al 2 O 3 ), and zeolite (HZSM-5) comparing with self-prepared zirconia (ZrO 2 ). The catalysts were synthesized via incipient wetness impregnation and evaluated for their performance in biofuel production. NiMo/Al 2 O 3 exhibited the lowest oxygen removal efficiency (68.5 %), while NiMo/HZSM-5 achieved a higher oxygen removal (74.3 %) but also demonstrated the highest coke formation. The type of support material influenced the resulting biofuel range, with NiMo/HZSM-5 and NiMo/ZrO 2 favoring jet fuel production, whereas NiMo/Al 2 O 3 was more suitable for diesel production. Notably, NiMo/ZrO 2 exhibited the highest performance in palm oil deoxygenation while minimizing coke formation. These findings highlight NiMo/ZrO 2 as a promising catalyst for efficient and stable biofuel production, with the support material significantly influencing product yield and fuel quality.
The overall objective of this work is to develop a new chemical absorbent-based, high pressure, CO 2 purification system to remove the residual oxygen that currently contaminates the recovered CO 2 , and to optimize the Pressurized Oxy-Combustion (POxC) process to minimize the Cost of Electricity (COE) generated in this advanced combustion process. TDA developed and validated the performance of the oxygen removal system for CO 2 purification. In collaboration with the Advanced Power & Energy Program (APEP) of University of California, Irvine (UCI), we optimized the POxC process, including thermal management, heat integration, and power cycle optimization using process design and modeling supported with Aspen Plus® process simulations. The techno-economic analysis results indicate that the pressurized oxycombustion coal power plant with Ion-transport membrane (ITM) air separation unit (ASU) (Case 2 – 30.55%) does not show an advantage over a cryogenic ASU (Case 1 – 31.24%) while TDA’s sorption-based ASU (Case 4 - 32.61%) shows a significant advantage over the cryogenic ASU (Case 1 – 331.24%). The specific plant costs show a wide range with a low of $2544/kW for Case 11C (TDA ASU, co-sequestering the SO x , and ultra-supercritical steam cycle) to a high of $2975/kW for Case 12A (cryogenic ASU and sCO 2 cycle). In general, the ITM ASU based cases have lower specific plant costs than the corresponding cryogenic ASU based cases while the TDA ASU based cases show the lowest specific plant costs. The main reason for lowering these costs is the higher overall plant thermal efficiency which decreases the plant cost on a $ per kW basis. Next comparing the cases with different power cycle working fluid conditions in terms of temperature and pressure while all utilizing steam, similar trends as the plant costs may be observed. However, with the supercritical CO 2 (sCO 2 ) cycle, the increase in thermal efficiency of the sCO 2 cycle was not able to offset its increase in plant cost making the plant costs higher than those of the corresponding steam cycle cases. The Cost of Electricity (COE) again shows similar trends as the specific plant costs. The COE for Case 11C at $110.1/MWh is also the lowest, but among all cases that do not co-sequester the SO x , Case 12C (TDA ASU and sCO 2 cycle) has the lowest COE at $\$$117.5/MWh while the highest is for Case 8A (cryogenic ASU and supercritical steam cycle) at $130.4/MWh.
Actinide chalcogenides are of interest for fundamental studies of the behavior of 5f electrons in actinides located in a soft ligand coordination environment. As actinides exhibit an extremely high affinity for oxygen, the synthesis of phase pure actinide chalcogenide materials free of oxide impurities is a great challenge and, moreover, requires the availability and use of oxygen free starting materials. Herein, we report a new method, the Boron-Chalcogen Mixture (BCM) method, for the synthesis of phase pure uranium chalcogenides based on the use of a boron/chalcogen mixture, where boron functions as an “oxygen sponge” to remove oxygen from an oxide precursor and where the elemental chalcogen effects transformation of the oxide precursor into an oxygen free chalcogenide reagent. Here, the boron oxide can be separated from the reaction mixture that is left to react to form the desired chalcogenide product. Several syntheses are presented that demonstrate the broad functionali-ty of the technique and thermodynamic calculations that show the underlying driving force are discussed. Specifically, three classes of chalcogenides that include both new (rare earth uranium sulfides and alkali-thorium thiophosphates) and previously reported compounds were prepared to validate the approach: binary uranium and thorium sulfides, oxide to sulfide transfor-mation in solid state reactions, and in situ generation of actinide chalcogenides in flux crystal growth reactions.
The primary goal of this project was to develop and validate advanced catalytic materials and systems for purifying the flue gas generated from pressurized oxy-combustors in an effort to achieve the purity specifications of carbon dioxide (CO 2 ) streams required by the U.S. Department of Energy (USDOE) for application in enhanced oil recovery. The technology has shown great potential for improving energy efficiency, simplifying process complexity, and lowering costs compared with current state-of-the-art oxy-combustion flue gas purification technologies. Laboratory studies were conducted for the development, characterization, and screening of metal catalysts for residual oxygen (O 2 ) reduction with methane (CH 4 ) and multifunctional carbon catalysts for combined nitrogen oxides (NO x ), sulfur oxides (SO x ), and mercury (Hg) removal. A bench-scale reverse-flow fixed-bed (RFFB) reactor and a trickle-bed direct-contact cooler (DCC) reactor capable of treating 15 standard liters per min of pressurized oxy-combustion flue gas were fabricated and tested with both a simulated flue gas in the laboratory and a slipstream of actual flue gas at a 100 kW th Staged, Pressurized Oxy-Combustion (SPOC) pilot facility. Process simulation and techno-economic studies were performed to evaluate the energy efficiency and cost of the developed catalytic flue gas purification process integrated into a conceptual 550-MWe SPOC power plant. The goal and objectives of the project have been successfully accomplished. A cobalt-manganese (CoMn) oxide catalyst was developed and demonstrated in the bench-scale RFFB reactor in either a reverse-flow or one-direction flow mode of operation that met the success criterion of performance for residual O 2 reduction. A carbon catalyst was developed and demonstrated in the bench-scale DCC reactor that met the success criterion of performance for combined NO x /SO x /Hg removal. Slipstream testing of the integrated DCC-RFFB system at the SPOC pilot facility demonstrated stable operation and verified the superior performance obtained in the laboratory. The techno-economic analysis showed that a 550-MWe SPOC plant integrated with the catalytic flue gas purification process would result in costs of electricity of $\$$96.94/MWh and $\$$80.27/MWh in two assessed cases compared with $\$$91.07/MWh reported for the USDOE’s Current Technology Case, which generated only a partially pure CO 2 stream. On the basis of the results and findings from this project, scale-up studies of materials production and system demonstration and optimization studies of reactors and processes are recommended at the next stage of technology development.
Solid base metal oxide catalysts such as MgO offer utility in a wide variety of syntheses from pharmaceuticals to fuels. The (111) facet of MgO shows enhanced, unique properties relative to the other facets. Carbon coatings have emerged as a promising modification to impart metal oxide catalyst stability. Here, we report the synthesis, characterization, and catalytic properties of commercial MgO, MgO(111), and carbon coated derivatives thereof for 2-pentanone condensation. The dimer and trimer products of this reaction can be used as precursors for biofuels upon oxygen removal and thus have relevance in environmental sustainability. Additionally, MgO(111) maintained impressive selectivity towards the dimer product after carbon coating, whereas the other catalysts experienced a decrease in conversion and selectivity as a consequence of the carbon coating. Our findings highlight the catalytic efficacy of MgO(111), provide insight into carbon coating for catalyst stability, and pave the way for continued mechanistic investigations.
Nanoscale iron oxides (e.g., hematite (a-Fe 2 O 3 )) have unique properties, such as enhanced chemical reactivity and high surface area, when compared with their bulk counterparts. These nanoscale surfaces can be more reactive due to the presence of defects (e.g., oxygen vacancies). In this work, we probed the surface chemistry of bulk and nanoscale hematite via X-ray photoelectron spectroscopy, electron microscopy, and powder X-ray diffraction. Oxygen exposure and vacuum annealing experiments were conducted to add or remove oxygen vacancies and remove adventitious carbon. In the absence of the oxygen annealing step, vacuum annealing resulted in partial reduction of Fe(III) to Fe(II) on all hematite surfaces. This was a size-dependent effect with the extent of reduction increasing as the crystallite size decreased. In addition, the atomic concentrations of carbon increased on all iron oxide surfaces after vacuum annealing. Oxygen annealing almost completely removed carbon from sample surfaces, and no Fe(III) reduction was observed in the absence of carbon. Under these conditions, the results reveal that carbonaceous material enhances oxygen vacancy formation, which then facilitates the reduction of Fe(III) on hematite surfaces. We provide new insights into the mechanisms of Fe(III) reduction on both bulk and nanoscale hematite surfaces and establish the major role of carbon in oxygen vacancy formation.
Understanding the reduction mechanism of ZnO/CuO x interfaces by hydrogen is of great importance for advancing the performance of industrial catalysts for CO 2 hydrogenation to methanol. Here, the reduction of pristine and ZnO-modified CuO x /Cu(111) by H 2 was investigated using ambient pressure scanning tunnelling microscopy (AP-STM), ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and density functional theory (DFT). The morphological changes and reaction rates seen for the reduction of CuO x /Cu(111) and ZnO/CuO x /Cu(111) are very different. On CuO x /Cu(111), perfect "44" and "29" structures displayed a very low reactivity towards H 2 at room temperature. A long induction period associated with an autocatalytic process was observed to enable the reduction by the removal of chemisorbed non-lattice oxygen initially and lattice oxygen sequentially at the CuO x -Cu interface, which led to formation of oxygen deficient "5-7" hex and honeycomb structures. In the final stages of the reduction process, regions of residual oxygen species and metallic Cu were seen. The addition of ZnO particles to CuO x /Cu(111) opened new reaction channels. On the ZnO sites, the dissociation of H 2 was fast and H adatoms easily migrated to adjacent regions of copper oxide. This hydrogen spillover substantially enhanced the rate of oxygen removal, resulting in the rapid reduction of the copper oxide located in the periphery of the zinc oxide islands with no signs for the reduction of ZnO. The deposited ZnO completely modified the dynamics for H 2 dissociation and hydrogen migration, providing an excellent source for CO 2 hydrogenation processes on the inverse oxide/metal system.
Amine oxidation is a major risk in the deployment of amine scrubbing for CO2 capture from post-combustion flue gas. Oxidation probably occurs by dissolved oxygen at elevated temperature, Fe(III)/Fe(II) shuttling between the absorber and the stripper, and by NO2 in the absorber. Amine selection, dissolved oxygen removal, and solvent reclaiming mitigate oxidation due to dissolved oxygen and iron shuttle mechanism, but not by NO2. This work examines piperazine (PZ) oxidation by NO2 in a bench-scale high gas flow reactor (HGF). PZ is an effective second-generation solvent with high CO2 capacity, fast capture rate, good thermal stability, and good resistance to oxidation. Flue gas typically contains 0.5–5 ppm NO2 and 10–100 ppm NO. NO2 at 1 ppm in the flue gas appears to cause significant amine oxidation in pilot plant testing. PZ solution can easily absorb NO2, and it is hypothesized that NO2 can catalytically oxidize PZ through free-radical propagation. The issue may not be solved by a NO2 pre-scrubber since the coexistence of NO and O2 in the flue gas will keep producing non-negligible amounts of NO2 in the ductwork and the absorber after the NO2 incoming with the flue gas has been scrubbed. In addition, NO2 may not only oxidize PZ but also the intermediate degradation products, and it is unknown if the existence of dissolved iron influences the oxidation by NO2. Previous workers have also shown that NO2 is the stoichiometric source of nitrosamine. A comprehensive analysis of NO2 oxidation is needed to address solvent management and its health/environmental impact. The new high gas flow (HGF) reactor focuses only on the absorber environment and is simpler to interpret because it does not include oxidation at high temperatures and by dissolved metal catalysts from corrosion. This paper presents the results of HGF experiments and shows evidence to support a hypothesis of amine oxidation catalyzed by NO2, presents the synergic effect of NO2 and iron on amine oxidation, points out the different effects of NO2 in clean and degraded solvents, and demonstrates that NO2 not only can oxidize amines but also their degradation products.
Captured carbon dioxide (CO 2 ) streams contain impurities that must be removed to meet specifications for safe transport, storage, and utilization. Among these impurities, oxygen poses challenges due to its high reactivity and potential to cause corrosion, motivating stringent purity limits below 10 ppmv. Building on recent experimental demonstrations of catalytic oxygen removal using hydrogen (H 2 ), carbon monoxide (CO), methanol (CH 3 OH), and methane (CH 4 ) as reducing agents, this study presents a technoeconomic (TEA) and life cycle assessment (LCA) of these four catalytic purification pathways. Process flowsheets were developed and simulated in Aspen Plus for CO 2 streams representative of both low-temperature and high-temperature capture processes, with integrated heat recovery and energy optimization. Results showed that total purification costs were dominated by feedstock procurement and electricity consumption. Among the studied reducing agents, the CH 4 -assisted route achieved the lowest purification cost and highest CO 2 recovery. Sensitivity analyses showed that the H 2 route became competitive at H 2 prices below $\$$0.56/kg to $\$$0.84/kg, depending on the CO 2 feed temperature conditions. In conclusion, environmental impacts were primarily driven by indirect CO 2 emissions from raw material production and utility consumption.
Systems and methods for energy storage and energy recovery are provided. An electrical-to-electrical energy storage system includes a thermochemical energy storage device, a blower, a compressor, a turbine, and an electrical generator. The TCES device includes a vessel, a porous bed, and a heater. The porous bed is disposed within an interior volume of the vessel. The porous bed comprises a reactive material. The reactive material is configured to release oxygen upon being heated to a reduction temperature, and generate heat when exposed to oxygen. The heater is in thermal contact with the reactive material. The blower is configured to remove oxygen from the interior volume. The compressor is configured to flow oxygen into the interior volume. The turbine is configured to receive a heated, oxygen-depleted gas from the interior volume. The generator is configured to be powered by the turbine to generate electricity.
Systems and methods for energy storage and energy recovery are provided. An electrical-to-electrical energy storage system includes a thermochemical energy storage device, a blower, a compressor, a turbine, and an electrical generator. The TCES device includes a vessel, a porous bed, and a heater. The porous bed is disposed within an interior volume of the vessel. The porous bed comprises a reactive material. The reactive material is configured to release oxygen upon being heated to a reduction temperature, and generate heat when exposed to oxygen. The heater is in thermal contact with the reactive material. The blower is configured to remove oxygen from the interior volume. The compressor is configured to flow oxygen into the interior volume. The turbine is configured to receive a heated, oxygen-depleted gas from the interior volume. The generator is configured to be powered by the turbine to generate electricity.