SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
System converts phase changes at optical frequencies to equal phase changes at RF. This system operates in conjunction with either a Michelson interferometer or conventional interferometers.
Phase change thermal control coating system as practical approach to space vehicle temperature control, discussing material and pigment selection
The phase change coating technique is used to obtain peak heating measurements in shock interference flow regions with high surface shear and heating. This technique provides heat transfer coefficients which are determined by measuring the time for a point on the surface to reach the phase change temperature of the thin fusible coating. Measurements were conducted on a 5.08-cm diameter hemisphere-cylinder made of silica based epoxy at Mach 6 for free stream Reynolds numbers of 3.3 to 25.6 million per meter. A sketch of the shock interference pattern produced by a flat plate shock generator is included. Heating data obtained on a 5.08-cm diameter stainless steel hemispherical model instrumented with thermocouples is presented for the purpose of comparing the phase change technique with the thermocouple-calorimeter technique.
Aluminum-based Al–Si alloys are widely used as phase change materials (PCMs) in thermal energy storage (TES) systems owing to their high volumetric latent heat and superior thermal conductivity. However, their long-term reliability is limited by degradation processes that remain insufficiently understood. In this work, we employ a multimodal, correlative characterization framework to systematically resolve the degradation behavior of eutectic Al–Si PCMs in contact with SS304 containers under repeated thermal cycling. By integrating high-resolution electron microscopy, three-dimensional X-ray fluorescence (3D XRF) imaging, and differential scanning calorimetry (DSC), we directly link spatially resolved compositional and microstructural evolution to changes in thermophysical properties. The correlative analysis reveals that elemental leaching of Fe, Cr, and Ni from the stainless-steel container into the PCM drives the formation of intermetallic compounds (IMCs) both at the interface and within the bulk PCM, leading to pronounced compositional heterogeneity. These interfacial reactions and diffusion-induced transformations progressively destabilize the Al–Si eutectic, reducing the effective phase-transforming fraction. Consistent with these observations, DSC measurements show a decrease in melting temperature and latent heat of fusion with thermal cycling. These results underscore the critical influence of interfacial reactions and material compatibility on the stability, durability, and overall performance of Al–Si-based TES systems.
Here, the present study examines the thermal energy storage (TES) effectiveness and printability of microencapsulated phase-change material (MEPCM) combined with thermoplastic polyurethane (TPU) for fused filament fabrication (FFF). Two formulations were assessed: 24D MEPCM, which changes phase at 24 ° C, compounded with TPU pellets and 43D MEPCM, which changes phase at 43 ° C, integrated with TPU powder. These combinations are designed to evaluate the effectiveness of the form of the TPU (pellets versus powder) in the FFF process. The investigation includes a comprehensive analysis of thermal characteristics, encompassing phase-change temperature, latent heat of fusion, thermal conductivity, and thermal decomposition, which are assessed through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, mechanical properties, including stress-strain behavior, are examined to evaluate material suitability for TES applications, while microstructural visualization is used to provide deeper insights into material performance, structural integrity, and the quality of printed components. The 24D MEPCM and TPU pellets formulation experienced a significant loss of approximately 39.6% of PCM during filament extrusion and printing, resulting in a reduced effective latent heat. Therefore, further characterization of the pellet formulation was discontinued due to excessive leakage. In contrast, the 43D MEPCM and TPU powder formulation demonstrated minimal PCM loss, with the 60 wt.% composition achieving an effective latent heat of 132 J/g. This value represents the highest effective latent heat currently documented in the literature for PCM-polymer-composite materials produced using an FFF-based additive manufacturing process.
Utilizing phase change materials (PCMs) within construction materials improves the thermal energy storage capabilities in the built environment. Notably, integrating PCMs into drywalls presents a promising avenue to reduce building energy use. However, incorporating PCMs into drywalls poses challenges, particularly reduced mechanical properties and workability limitations as it can adversely affect the hardening and cohesiveness of gypsum composites. To address these challenges, this study explores a novel strategy to incorporate PCMs into gypsum composites through fly ash cenosphere-encapsulated PCM, namely CenoPCM, aiming to enhance the mechanical properties and thermal conductivity over existing commercial counterparts. An experimental program was conducted to study the impact of the inclusion of CenoPCM on the mechanical and thermal performance of gypsum composites, and the results were compared to those of commercially available polymerencapsulated PCM benchmark (Micronal). The findings highlighted that PCM-charged samples exhibited up to 95.90 J/g (CenoPCM) of latent heat with 70 % CenoPCM loading. The results of mechanical tests also showed that CenoPCM outperformed its polymer-encapsulated counterpart, achieving 55 % higher mechanical strength on average. Here, this improvement is attributed to the rigid shell of fly ash cenosphere (FAC) serving as a PCM carrier, providing a skeleton-like structure to gypsum composites for higher load-bearing capacity. Additionally, hotbox tests demonstrated that the CenoPCM-charged wall panels yielded a 20 % higher thermal conductivity and a 22 % increased time lag compared to Micronal PCM-charged panels, indicating its potential to shift the peak load in buildings.
Phase change solidification phenomena in n- hexadecane for spacecraft thermal control systems, considering two or three dimensional models
The phase-change coating technique presents itself as a valuable tool in determining the heat transfer rate over the surface of small complex wind tunnel models. A numerical technique is described which shows that an effective thermophysical property - the square root of the product of thermal conductivity, density, and specific heat - may significantly improve the accuracy of the phase-change coating technique with allowance for model inhomogeneity and temperature dependency in a transient environment. Results of the measured steady-state variation of the effective thermophysical property with temperature and the effect of surface heating rate on the effective thermophysical property are plotted for a representative homogeneous model material and for an extreme nonhomogeneous model material. The use of an effective thermophysical property to reduce phase-change paint data is recommended. The analysis also confirms that the apparatus described by Corwin and Kramer (1975) can be used to measure directly this effective thermophysical property for use in wind tunnel model heat-transfer measurements.
Strongly correlated materials exhibiting phase transitions which can be controlled through external stimuli, such as electric fields, are promising for future computing technologies beyond conventional semiconductor transistors. Devices that take advantage of structural phase transitions have inherent built‐in memory, reminiscent of synapses and neurons, and are thus natural candidates for neuromorphic computing. Of particular interest are phase‐change oxides, which allow for control over the metal‐to‐insulator transition. Here, X‐ray nano‐diffraction structural imaging of micro‐devices fabricated with the archetypal phase‐change material vanadium sesquioxide (V 2 O 3 ) is reported. The devices contain a Ga ion‐irradiated region where the metal‐to‐insulator transition critical temperature is lowered, a useful feature for controlling neuron‐like spiking behavior. Results show that strain, induced by crystal lattice mismatch between the pristine and irradiated material, leads to a suppression of the metal‐to‐insulator‐transition. Suppression occurs within the irradiated region or along its edges, depending on the defect‐distribution and the size of the region. The observed self‐straining effect can extend to other phase‐change oxides and dominate as device dimensions are reduced and become too small to dissipate strain within the irradiated region. The findings are important for phase engineering in phase‐change devices and highlight the necessity to study phase transitions at the nanoscale.
A phase change material heat capacitor prototype, designed and built under a NASA Small Business Innovation Research grant by Mezzo Technologies, was tested through coolant thermal cycling within the expected flow rates and temperature range of the Orion spacecraft’s propylene glycol-water mixture coolant system. Testing was performed with the phase change material contained under sealed conditions after a degassing procedure and exposed to atmosphere without prior degassing. The useful heat storage capacitance was measured and compared to Orion spacecraft requirements and theoretical N-Pentadecane storage capacity.
Comprehensive survey is given of the thermal aspects of phase change material devices. Fundamental mechanisms of heat transfer within the phase change device are discussed. Performance in zero-g and one-g fields are examined as it relates to such a device. Computer models for phase change materials, with metal fillers, undergoing conductive and convective processes are detailed. Using these models, extensive parametric data are presented for a hypothetical configuration with a rectangular phase change housing, using straight fins as the filler, and paraffin as the phase change material. These data are generated over a range of realistic sizes, material properties, and thermal boundary conditions. A number of illustrative examples are given to demonstrate use of the parametric data. Also, a complete listing of phase change material property data are reproduced herein as an aid to the reader.
Phase change materials (PCMs) store and release large amounts of thermal energy because of their high latent energy storage capacity. However, long-term cyclic stability, supercooling and performance-scalability are some of the major challenges for their use in building thermal energy storage (TES) applications. Here, in this study, we present a comprehensive multiscale characterization of two commercially available organic PCMs, Puretemp 18 and Puretemp 23. At the microscale, differential scanning calorimetry (DSC) was used to characterize phase change temperature, specific heat, and latent heat. At the mesoscale, a heat flow meter apparatus (HFMA), following the ASTM C1784 standard, was employed to measure the phase change temperature, specific heat, and latent heat properties. A comparative analysis of latent heat as a function of temperature was conducted by integrating the DSC and HFMA results. At the macroscale, the thermal performance and cyclic stability of the TES system was evaluated using Puretemp 23. The TES system consisted of a finned tube heat exchanger with a storage volume of 0.0189 m 3 (5 gal), which represents a compact, real-world TES solution suitable for building energy storage. The results showed consistent thermal stability of the PCM over 200 cycles, and the supercooling temperature remained within 0.2 °C, which was not detected in smaller-scale characterization methods. Additionally, the macroscale testing methodology of the PCM revealed that the TES is able to charge and discharge stored latent energy within 2 h under a temperature differential of 16.67 °C measured between the inlet water temperature and the phase transition temperature of the PCM. The proposed multiscale PCM characterization method provides a systematic basis for comparing important thermal storage properties while also investigating the scalability, reliability and integration challenges in large scale TES applications.
Handbook describes relationship between phase-change materials and more conventional thermal control techniques and discusses materials' space and terrestrial applications. Material properties of most promising phase-change materials and purposes and uses of metallic filler materials in phase-change material composites are provided.
The procedures used in the application of the phase change technique to the phase B shuttle configuration are discussed along with factors which may affect data accuracy. These factors include variation of thermal properties of phase change model material, sensitivity of measured heat transfer coefficients to the assumed value of the adiabatic to total temperature ratio, and wall temperature effects. These sensitivities are illustrated in sample calculations for a shuttle geometry. Factors which may affect the visual clarity and interpretation of phase change data are discussed, and a method of improving photographic data quality through the use of polarized light is presented.
Ramsey's (1948, 1949, 1950, 1954) arguments for the phase-change interpretation of the nature of the terrestrial core are summarized. Some of the successes of the phase-change theory in accounting for hitherto unexplained properties of earth's interior are discussed. Evidence in favor of the phase-change theory is reviewed, and calculations are examined which indicate that the liquid-core material is far more compressible at any relevant pressure than is the mantle material. Implications of the phase-change theory for Venus, Mars, Mercury, and the moon are considered.
Natural convection effects in phase change thermal control devices were studied. A mathematical model was developed to evaluate natural convection effects in a phase change test cell undergoing solidification. Although natural convection effects are minimized in flight spacecraft, all phase change devices are ground tested. The mathematical approach to the problem was to first develop a transient two-dimensional conduction heat transfer model for the solidification of a normal paraffin of finite geometry. Next, a transient two-dimensional model was developed for the solidification of the same paraffin by a combined conduction-natural-convection heat transfer model. Throughout the study, n-hexadecane (n-C16H34) was used as the phase-change material in both the theoretical and the experimental work. The models were based on the transient two-dimensional finite difference solutions of the energy, continuity, and momentum equations.
Phase-change materials play a critical role in industrial energy storage applications to drive efficiency improvements, thermal energy management, and carbon emissions reductions. Recently, it has been shown that rapid solidification of alloys with metastable immiscibility in the liquid phase has the potential to form unique microstructures in which a low-melting phase is uniformly distributed in a high-melting matrix. This feature can be exploited using additive manufacturing to produce components with complex geometries containing such unique phase-change microstructures. Phase-field simulations utilizing high-performance computing were used to provide a detailed description of the evolution of the active phase during service in terms of their morphology and composition in different polycrystalline matrix grain morphologies that are typically produced during additive manufacturing. Phase field simulations were performed using, MEUMAPPS-SL (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid Liquid) code that was developed in-house by the Oak Ridge National Laboratory. The simulations utilized the capabilities of the Kestrel supercomputer at the National Renewable Energy Laboratory. The simulation results were compared with experimental results generated at Siemens Energy, Inc. The results indicate that the kinetics of liquid spreading along grain boundaries is largely determined by the mobility of the triple line along the intersection of the grain boundary liquid and the grain boundary plane.
Energy storage technologies, particularly those utilizing phase change materials (PCMs), have gained attention for their high energy density and efficient thermal management. PCMs, which store energy through solid-liquid phase transitions, can efficiently capture and release thermal energy, but face the challenge of leakage during the phase change process. Inorganic PCMs, such as salt hydrates, offer high energy storage capacity, but are difficult to encapsulate due to their corrosive nature. Conventional encapsulation techniques for inorganic PCMs are limited, particularly for scalable applications. In this work, we present an innovative method for the encapsulation of salt hydrate-based inorganic PCMs (CaCl 2 ·6H 2 O) using co-axial electrospinning. The process involves the creation of co-axial fibers, with salt hydrate as the core and polymer (e.g., PVP) as the outer shell, effectively preventing leakage and improving the stability of the PCM. This approach demonstrates the potential for scalable microencapsulation of inorganic PCMs, marking the first report of using co-axial electrospinning for this purpose. This novel technique could contribute to enhancing the performance and applicability of PCMs in thermal energy storage systems and other energy efficiency applications.