Search NASA⌕ Search

SEARCH · Search NASA

Results for “PHYSICAL PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Evaluation of Hanford 200 West Area Tank Farms (241-S/241-SX-/241-U tank farms) Physical Properties Data for Use in Development of West Area Tank Treatment (WATT) Processing

With the recent acceptance of West Area Tank Treatment disposition alternative for 200 West Area tanks at the Hanford Site by the State of Washington and the U.S. Department of Energy, a review was initiated to identify the physical properties data available in the literature for the Hanford 241-S, 241-SX, and 241-U tank farms. The literature reviewed indicated that there is a relatively small set of useful data on physical properties of 200 West Area tanks, and the data that do exist are biased around a narrow range of tank samples. Much of the testing between the 1990s and mid-2010s was intended to support either enhanced sludge washing or feed delivery to the Pretreatment Facility at the Hanford Waste Treatment and Immobilization Plant. As such, some physical properties of 200 West Area samples were measured under conditions that are no longer relevant. Because of the distinctly different nature of many past processes at the 200 West Area compared to the 200 East Area, insight from waste testing in the 200 East Area waste should be used with caution, as there may be significantly different qualities in the physical properties data between these two areas (both in situ and as measured in laboratory analyses). Based on this assessment, there is a need to collect additional physical property data to support planning for 200 West Area retrievals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Effects of Recovery Conditions and Aggregation Mechanisms on the Chemical and Physical Properties of Hybrid Poplar and Corn Stover Lignins

Heterogeneity in the physical properties and processing behavior of lignins recovered from biorefining process streams can hinder their effective utilization and industrial valorization. This work investigates lignin recovery by acidification from alkaline pretreatment liquors of varying sources (corn stover and hybrid poplar), compositions, solid contents, and incubation temperatures prior to filtration. Recovered lignins were characterized for filtration performance, mass yield, chemical composition, particle size and morphology, and color. A transition temperature was identified corresponding to marked shifts in lignin physical properties and was a function of the solid content and liquor source. Filtration below this temperature yielded slow-filtering, dark, brittle lignins with smoother particle surfaces, whereas precipitation above this threshold yielded fast-filtering, lighter, powdery lignins with rougher particle surfaces. The impact of temperature and concentration on universal cluster aggregation mechanisms was proposed to explain the differences between lignin particle properties and filtration behavior.

Aggregation↗
DOE OSTI2024

Physical Properties of Hilti HIT-RE 500 V3 After Irradiation: Slant Shear, Tensile, Flexural, and Compressive

There are various applications in which epoxy adhesives may be used within hot-cell environments. These epoxies currently see limited use within hot cells since it is known that organics see degradation after small doses even as low as 50 kilogray (kGy). These losses in physical property strengths limit the use of these epoxies to non-structural applications. In modern construction, however, the use of epoxies to bond structural components such as rebar or threaded anchors is becoming increasingly prevalent. To employ these types of materials the Idaho National Laboratory (INL) has begun investigating the specific degradation properties of epoxies for use in structural applications in environments where radiation is present. Hilti HIT-RE 500 V3 is used extensively in new construction and renovation projects across the world. The INL has conducted various tests on this epoxy for low dose environments. These tests include tensile, flexural, compression, and slant shear tests following the American Society for Testing Material International (ASTM) standards D638, D790, D695, and C882/882M respectively. Two sample sets for each test were created where the baseline specimens were not irradiated, and another set was irradiated to an accumulated dose of approximately 50-60 kGy. All the samples were destructively tested and analyzed focusing on the change in physical properties, examples of these tests are shown in Figures 1-4. Tensile testing results indicate a 0.9% loss in maximum load capacity, a 0.5% loss in tensile stress at maximum load, a 1.4% loss in tensile strain at break, and a 15% decrease in modulus of elasticity. Flexural testing results display an increase in all the following: 12% in strain at maximum load, 10% in maximum load capacity, 5% in stress at maximum load, and 3% in young’s modulus. The compressive physical properties after irradiation display a 1% increase in maximum load, a 3% decrease in stress at yield, and a 5% decrease in modulus of elasticity. The maximum compressive stress saw no measurable change after irradiation. The slant shear specimens after irradiation displayed a 2% increase in maximum load capacity and maximum compressive stress. Though a structural analysis would have to be completed as is normal for building design the increases and decreases in the measured physical properties indicate that this material may be used for structural applications in low dose hot-cell environments without adhesive failure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Value-added catalog of physical properties for more than 1.3 million galaxies from the DESI survey

We present an extensive catalog of the physical properties of more than a million galaxies investigated with the Dark Energy Spectroscopic Instrument (DESI), one of the largest spectroscopic surveys to date. Spanning a full range of target types, including emission-line galaxies, luminous red galaxies, and quasars, our survey encompasses an unprecedented range of spectroscopic redshifts, all the way from 0 to 6. The physical properties, such as stellar masses and star formation rates, were derived via the CIGALE spectral energy distribution (SED) fitting code accounting for the contribution coming from active galactic nuclei (AGNs). Based on the modeling of the optical-mid-infrared (grz supplemented with WISE photometry) SEDs, we studied the galaxy properties with respect to their location on the main sequence. We have revised the dependence of stellar mass estimates on model choices and on the availability of WISE photometry. Indeed, the WISE data are required to minimize the misclassification of star-forming galaxies as AGNs. The lack of WISE bands in SED fits leads to elevated AGN fractions for 68% of star-forming galaxies identified using emission line diagnostic diagrams, but this does not significantly affect their stellar mass or star formation estimates.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Physical properties, internal structure, and the three‐dimensional petrography of CI chondrites

physical properties and the nature of their breccation, we investigated nine samples of the Ivuna and Orgueil CI chondrites ranging in size from 1 mm to 4 cm in approximate diameter. The combined mass of unique material investigated in this work is 113 g. For our investigations, we use ideal gas pycnometry, 3-D laser scanning, x-ray computed microtomography (μCT), and accompanying digital data extraction techniques. We found that the bulk density of the samples ranged from 1.61 to 2.10 g cm −3 . Larger samples tend to have a lower bulk density. Grain density (ranging from 2.44 to 2.55 g cm −3 ) is significantly less variable than the bulk density in our samples and the quantity of porosity (ranging from 14.6% to 33.8%) is the dominant factor in determining the bulk density of CI chondrite material. Our μCT results show that the visible porosity across all sizes of our CI chondrite samples is in the form of cracks, but these cracks can account for less than two-thirds of the porosity in the CI chondrites. Other porosity is not visible, even at μCT resolutions of 2.7 μm voxel edge −1 and we conclude that it is sub-micron in nature. It is not clear if the cracks seen in our samples are indigenous to the chondrites or are a result of terrestrial processes. We also find that the CI chondrites are excellent examples of the fractal-like nature of brecciation, where clasts can be observed at all scales we imaged. The breccias are composed of sub-equant-shaped and sub-rounded-textured clasts like melt-free impact breccias on other solar system bodies. From our μCT volume and digital data extraction, we determine that the Ivuna CI chondrite breccia is organized: the mostly sub-equant clasts within our ~2 cm chunk of Ivuna have a mean diameter of 1.33 mm and their aligned longest axes define a lineation structure. We speculate that the lineation was imparted after fragmentation of the clasts by slight shear on the parent asteroid which could be the result of seismic-related granular flow or mild non-axial impact-related compaction. These data will help to place returned asteroidal material from asteroids 162173 Ryugu and 101955 Bennu and the CI chondrites into a mutual geological context.

CI chondrite↗
DOE OSTI2026

Ultrasonic-Assisted Extrusion Processing for Enhancing Physical Properties of High-Density Polyethylene by Flow-Induced Crystallization

The evolution of crystallinity resulting from stress imposed on a melt, known as flow-induced crystallinity, can strongly influence the mechanical and physical properties of semicrystalline polymers. This study investigates shear-induced crystallization by applying an ultrasonic field to the melt flow as it passes through dies with various geometries. A custom-built sonication die is employed for controlling the dynamic temperature and shear environment, resulting in molecular alignment and potential for flow-induced crystallization. Application of both conventional and ultrasonic shear rates at the equilibrium melt temperature of high-density polyethylene (HDPE) was investigated to accelerate crystallinity and manipulate the crystal morphology across the film in pursuit of improved mechanical and gas barrier properties without the need for additives or other polymer layers. The relationships among ultrasonic-assisted extrusion processing, polymer structure, and performance were analyzed using wide- and small-angle X-ray scattering (WAXS and SAXS), tensile testing, and oxygen transmission rate (OTR) analysis. Multiple linear regression models were implemented to predict the correlation among HDPE structure, process, and properties. Structural analysis revealed that both conventional and ultrasonic shear rates had the most significant influence on lamellar spacing and redistribution of rigid and soft amorphous fractions within the crystalline domains, ultimately dictating the mechanical and physical properties of the films. The goal is to explore the potential of the ultrasonic-assisted high crystallinity monolayer that can replace some of the functionality of complex, heterogeneous multilayer packaging with a single-material film having enhanced oxygen barrier properties.

crystallinity↗
DOE OSTI2026

pop-cosmos : redshifts and physical properties of KiDS-1000 galaxies

ABSTRACT Principled Bayesian inference of galaxy properties has not previously been performed for wide-area weak-lensing surveys with millions of sources. We address this gap by applying the pop-cosmos generative model to perform spectral energy distribution (SED) fitting for 4 million KiDS (Kilo-Degree Survey)-1000 galaxies. Calibrated on deep COSMOS2020 photometric data, pop-cosmos specifies a physically motivated prior over the galaxy population up to $z \simeq 6$ in stellar population synthesis (SPS) parameter space. Using the Speculator SPS emulator with GPU (graphics processing unit)-accelerated Markov Chain Monte Carlo sampling, we perform full posterior inference at 8.2 GPU seconds per galaxy, obtaining joint constraints on galaxy redshifts and physical properties. We validate photometric redshifts against $\sim \!185\,\!000$ KiDS galaxies cross-matched to Dark Energy Spectroscopic Instrument Data Release 1 spectroscopic samples, achieving low bias ($2\times 10^{-3}$), scatter ($\sigma _{\mathrm{MAD}}=0.03$), and outlier fraction (3.2 per cent) for the Bright Galaxy Survey, with comparable performance (bias $3\times 10^{-2}$, $\sigma _{\mathrm{MAD}}=0.05$, 1.0 per cent outliers) for luminous red galaxies (LRGs). Within the LRG sample, we identify massive, dusty, star-forming contaminants at $z \simeq 0.4$ satisfying standard colour selections for quenched populations. We infer trends in stellar mass, star formation, metallicity, and dust across five tomographic redshift bins consistent with established scaling relations. Using specific star formation rate constraints, we identify $\sim$7 per cent of KiDS-1000 galaxies as quenched, versus 37 per cent implied by conservative colour cuts. This enables the construction of weak-lensing samples defined by physical properties while mitigating intrinsic alignment systematics and preserving statistical power. Our analysis validates pop-cosmos out of sample, establishing it as a scalable approach for galaxy evolution and cosmological analyses with photometric surveys.

Halder, Anik [Institute of Astronomy and Kavli Ins↗
DOE OSTI2025

Physical properties of intergrowth compound Eu 2 CuZn 2 P 3

Here, the physical properties of single-crystalline Eu 2 ⁢CuZn 2 ⁢P 3 were inspected via thermodynamic, transport, and neutron diffraction measurements. Eu 2 ⁢ CuZn 2⁢ P 3 is composed of EuCuP and EuZn 2 ⁢ P 2 motifs stacked in a one-to-one ratio. The magnetic response of Eu 2 ⁢ CuZn 2 ⁢ P 3 is similar to that of EuZn 2 ⁢ P 2 in its A-type antiferromagnetic (semiconducting) state. A Néel temperature of T N = 40.3K is obtained from the specific heat capacity. Single-crystal neutron diffraction reveals a (001) magnetic propagation vector, with primarily in-plane moments coupled along [001] in an up-up-down-down pattern. This spin structure retains the ferromagnetic EuCuP motifs and antiferromagnetic coupling across the EuZn 2 ⁢P 2 motifs. The electrical resistivity is characterized by metallic behavior above 100 K, an increase in ρ upon cooling below ≈ 75K, and a large negative magnetoresistance below T N . First principles calculations evidence a narrow band gap for antiferromagnetic ordering and semimetallic behavior for the ferromagnetic state. This is consistent with the observed effect of magnetic field on the electrical resistivity. Hall effect measurements reveal a field-induced, negative anomalous Hall effect that increases on cooling down to 2 K. Also, an unconventional contribution to the Hall effect dominates the low-field Hall signal, particularly near T N , and is similar in appearance to a topological Hall effect. However, further work is necessary to understand if any of the transport properties have topological origins or if magnetism-induced modifications to the Fermi surface induce these unusual Hall effect signals in this and related materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electro-physical properties of surface-barrier diodes on low-resistance n-Cd 0.96 Mn 0.04 Te 0.96 Se 0.04 crystals

The electro-physical properties of Cd 0.96 Mn 0.04 Te 0.96 Se 0.04 n-type conductivity single crystals with relatively low resistivity were studied. The determined resistivity of semiconductor single crystals Cd 0.96 Mn 0.04 Te 0.96 Se 0.04 n-type conductivity is equal to ρ≈2 Ω-cm at 293K. The activation energy of dark conductivity, measured from the temperature dependence of the resistivity of the In/Cd 0.96 Mn 0.04 Te 0.96 Se 0.04 /In structure, is equal to ΔE≈0.11eV. From optical measurements of the absorption coefficient from the energy of photons in the region of large α, the band-gap width of the single crystal was found, which is equal to E g =1.53eV. Diode structures of Ni/Cd 0.96 Mn 0.04 Te 0.96 Se 0.04 /In obtained by vacuum sputtering of Ni on the surface of a single crystal n-Cd 0.96 Mn 0.04 Te 0.96 Se 0.04 were manufactured and studied. Here, the rectification coefficient at a voltage of U=1V is equal to 10 8 . Within the framework of the Sah-Noys-Shockley carrier generation-recombination model, a quantitative match of the experimental measurements of the volt-ampere characteristics with the calculation was achieved.

(Cd,Mn)(Te,Se)↗
DOE OSTI2024

Structural and physical properties of two distinct 2D lead halides with intercalated Cu( II )

Transition metal cation intercalation between the layers of two-dimensional (2D) metal halides is an underexplored research area. In this work we focus on the synthesis and physical property characterizations of two layered hybrid lead halides: a new compound [Cu(O 2 C–CH 2 –NH 2 ) 2 ]Pb 2 Br 4 and the previously reported [Cu(O 2 C–(CH 2 ) 3 –NH 3 ) 2 ]PbBr 4 . These compounds exhibit 2D layered crystal structures with incorporated Cu 2+ between the metal halide layers, which is achieved by combining Cu(II) and lead bromide with suitable amino acid precursors. The resultant [Cu(O 2 C–(CH 2 ) 3 –NH 3 ) 2 ]PbBr 4 adopts a 2D layered perovskite structure, whereas the new compound [Cu(O 2 C–CH 2 –NH 2 ) 2 ]Pb 2 Br 4 crystallizes with a new structure type based on edge-sharing dodecahedral PbBr5O3 building blocks. [Cu(O 2 C–CH 2 –NH 2 ) 2 ]Pb 2 Br 4 is a semiconductor with a bandgap of 3.25 eV. It shows anisotropic charge transport properties with a semiconductor resistivity of 1.44 × 10 10 Ω cm (measured along the a-axis) and 2.17 × 10 10 Ω cm (along the bc-plane), respectively. The fabricated prototype detector based on this material showed response to soft low-energy X-rays at 8 keV with a detector sensitivity of 1462.7 μCGy –1 cm –2 , indicating its potential application for ionizing radiation detection. Finally, these encouraging results are discussed together with the results from density functional theory calculations, optical, magnetic, and thermal property characterization experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Study of electro-physical properties of CsPbBr3 perovskite single crystals

Methods have been developed for the synthesis and growth of lead halide perovskites CsPbBr3, which can be used as detectors of optical, X-ray and gamma-radiation. Single crystals of these compounds were grown by the Bridgman method. The melt temperature was 580 °C, the gradient at the crystallization front was 5 K/cm, and the ampoule lowering speed was 3 mm/hour. In this work, the electro-physical properties of the inorganic perovskite CsPbBr3 were investigated. Crystals for research were cut from the beginning and end of the ingot. The optical absorption spectra were measured depending on the crystal thickness and temperature, the differential resistivity dif and the product  were determined from the I-V characteristics. It was established that dif practically does not change for samples made from the beginning and the end of the ingot, and is dif  21010 Ωcm at 100 V and 293 K.

Sklyarchuk, V.↗
DOE OSTI2025

Hexagonal Boron Nitride: Physical Properties, Hydride Vapor‐Phase Epitaxy Growth of Large‐Diameter Quasi‐Bulk Wafers and Applications

Hexagonal boron nitride ( h ‐BN), with its ultrawide bandgap and 2D structure, holds an immense promise for advanced semiconductor applications. Scaling bulk crystals to large‐diameter wafers, crucial for complex device fabrication, remains a challenge with high temperature, high pressure, and metal flux solution methods. To address this, recent efforts have focused on hydride vapor‐phase epitaxy (HVPE) for producing large diameter thick h ‐BN quasi‐bulk wafers, reaching hundreds of micrometers. These HVPE‐grown quasi‐bulk crystals exhibit excellent c ‐axis long‐range order. Notably, the in‐plane mobility‐lifetime products for both electrons and holes surpass 10 −4 cm 2 V −1 , which are two orders of magnitude greater than the out‐of‐plane (vertical) values, highlighting the potential for high‐performance devices leveraging superior lateral transport. Lateral detectors fabricated from 100 μm thick B‐10 enriched h‐ BN wafers have achieved a record 60% thermal neutron detection efficiency. Based on its physical properties, h‐ BN appears to be an outstanding material of choice for light‐triggered electronic power switches capable of supporting high ‐ voltage and high ‐ power operations. These recent advancements in large‐diameter h ‐BN quasi‐bulk crystal growth, enabled by HVPE, pave the way for applications spanning deep UV photonics, high‐power electronics, high‐efficiency neutron detection, and quantum information technologies, establishing h ‐BN as both a versatile active semiconductor and an ideal substrate.

Jiang, Hongxing [Department of Electrical and Comp↗
DOE OSTI2026

Validating corrosion models: Influence of physical properties

In chloride containing environments, two metals in physical contact can undergo galvanic corrosion limiting the lifetime of components. Being able to accurately predict galvanic corrosion damage distributions over time has not been widely presented in literature. Therefore, Finite Element Method (FEM) corrosion models were experimentally validated for two galvanic couples as a function of governing equations, environment, anode material, anode:cathode ratio, and time. Carbon steel/stainless steel (CS/SS) and zinc/stainless steel (Zn/SS) galvanic couples were exposed to NaCl solutions at room temperatures for up to 14 days. For the galvanic couples and environments, the Laplace equation with variable conductivity and reactions was sufficient to model the experimental corrosion damage. Increasing the chloride concentration for the CS/SS galvanic couple, regardless of the anode:cathode ratio, decreased the observed and modeled corrosion damage. Decreasing the anode:cathode ratio (i.e., increasing the cathode length), increased the experimentally observed and modeled corrosion damage. For small anode:cathode ratios, the governing equations deviate over long time periods with the Nernst-Plank equation being conservative. For the Zn/SS galvanic couple, the cathode length controls the dominant cathodic reduction reaction. For small cathode lengths, the hydrogen evolution reaction is dominant. For larger cathode lengths, the oxygen reduction reaction is dominant. The results are discussed with regard to the influence of solution chemistry, ohmic drop, and governing reactions. Overall, validated FEM models were presented, and the resultant models, physics, and mechanisms can be applied to other corrosion scenarios with confidence.

Carbon steel↗
DOE OSTI2024

Method of tuning physical properties of thermosets

Polymerization-induced phase separation enables fine control over thermoset network morphologies, yielding heterogeneous structures with domain sizes tunable over 1-100 nm. However, the controlled chain-growth polymerization techniques exclusively employed to regulate morphology at these length scales are unsuitable for most thermoset materials typically formed through step-growth mechanisms. By employing binary mixtures in place of the classic constituents of phase-separating thermosets—resin, curing agent, and secondary polymer—facile tunability over morphology can be achieved through a single compositional parameter. Indeed, this method yields morphologies spanning nano-scale to macro-scale, controlled by the relative reactivities and thermodynamic compatibility of the network components. Due to the connection between chain dynamics and microstructure in these materials, the tunable morphology enables exquisite control over glass transition and other physical and mechanical properties.

Jones, Brad Howard↗
DOE OSTI2025

Physical properties of 𝑅⁢ Co 2 ⁢Al 8 single crystals (𝑅 = La, Ce, Pr, Nd, and Sm) : An emerging structure-type for anisotropic Kondo-lattice studies

Systematic investigations of rare-earth (𝑅)-based intermetallic materials are a leading strategy to reveal the underlying mechanisms governing a range of physical phenomena, such as the formation of a Kondo lattice and competing electronic and magnetic anisotropies. Here, in this work, the magnetic, thermal, and transport properties of 𝑅⁢Co 2 ⁢Al 8 (𝑅 = La, Ce, Pr, Nd, and Sm) single crystals are presented. LaCo 2 ⁢Al 8 is characterized as a Pauli paramagnet, and transport measurements, with the current along and perpendicular to the orthorhombic 𝑐-axis (𝜌 𝑐 and 𝜌 𝑎⁢𝑏 , respectively), reveal a clear electronic anisotropy, with 𝜌 𝑎⁢𝑏 ⁢≈ (4 –7)⁢𝜌 𝑐 at 300K . We show that CeCo 2 ⁢Al 8 is a Kondo lattice for which the Kondo coherence temperature 𝑇$^*_K$, deduced from broad maximums in 𝜌 𝑐 and 𝜌 𝑎⁢𝑏 at ≈ 68 and 46 K, respectively, is also anisotropic. This finding is related to a possible underlying anisotropy of the Kondo coupling in CeCo 2⁢ Al 8 . The Pr- and Nd-based materials present strong easy-axis anisotropy (𝑐-axis) and antiferromagnetic (AFM) orders below 𝑇 = 4.84 and 8.1K , respectively. Metamagnetic transitions from this AFM to a spin-polarized paramagnetic phase state are investigated by isothermal magnetization measurements. The Sm-based compound is also an easy-axis AFM with a transition at 𝑇 = 21.6K .

Garcia, Fernando A. [Ames Laboratory (AMES), Ames,↗
DOE OSTI2024

Elucidation of Ce/Zr ratio effects on the physical properties and catalytic performance of CuO x /Ce y Zr 1− y O 2 catalysts

Although cerium oxide (CeO 2 ) is widely used as a catalyst support, its limited defect sites and surface oxygen vacancy/mobility should be improved. The incorporation of zirconium (Zr) in the cerium (Ce) lattice is shown to increase the number of oxygen vacancies and improve catalytic activity. Using a fixed surface density (SD) of copper (∼2.3 Cu atoms per nm 2 ) as a surface species, the role of the support (Ce y Zr 1−y O 2 (y = 1.0, 0.9, 0.6, 0.5, and 0.0)) and defect site effects in the CO oxidation reaction was investigated. Spectroscopic (e.g., Raman, XRD, XPS) and microscopic (e.g., SEM-EDX, HR-TEM) characterization techniques were applied to evaluate the defect sites, crystallite size, lattice parameters, chemical composition, oxidation states of elements and microstructure of the catalysts. Here, the CO oxidation reaction with varied CO : O 2 ratios (1 : 5, 1 : 1, and 1 : 0.5 (stoichiometric)) was used as a model reaction to describe the relationship between the structure and the catalytic performance of each catalyst. Based on the characterization results of Ce y Zr 1−y O 2 materials, the addition of Zr causes physical and chemical changes to the overall material. The inclusion of Zr into the structure of CeO 2 decreased the overall lattice parameter of the catalyst and increased the number of defect sites. The prepared catalysts were able to reach complete CO conversion (∼100%) at low temperature conditions (<200 °C), each showing varied reaction activity. The difference in CO oxidation activity was then analyzed and related to the structure, wherein Cu loading, surface oxygen vacancies, reduction–oxidation ability, CuO x –support interaction and oxygen mobility in the catalyst were the crucial descriptors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magnetic order and physical properties of the kagome metal UNb 6 ⁢Sn 6

The 𝑅⁢𝑀 6 ⁢𝑋 6 family of materials (𝑅 = rare-earth, 𝑀 = transition metal, 𝑋 = Ga, Si, Ge, Sn) produces an array of emergent phenomena, such as charge density waves, intrinsic Hall effects, and complex magnetic order, due to its kagome net of transition metal atoms, its local-moment magnetic anisotropies, and its extensive chemical tunability. Here, in this study, we report UNb 6⁢ Sn 6 , a new “166” material containing both an actinide and a 4⁢𝑑 transition metal, along with its nonmagnetic analog ThNb6⁢Sn6, to investigate the properties of a 5⁢𝑓−4⁢𝑑 electron 166 system. UNb 6 ⁢Sn 6 crystallizes in the hexagonal 𝑃⁢6/𝑚⁢𝑚⁢𝑚 space group with a small degree of disorder due to shifts in the size of the CoSn-like cages along the 𝑐 axis. Upon cooling at zero magnetic field, the material undergoes two magnetic phase transitions at 𝑇 2 = 46K and 𝑇 N = 43K. The low-temperature, zero-field phase is an antiferromagnet with ordered uranium moments and a k = (0,0,1/2) propagation vector determined by neutron diffraction. Remarkably, with a magnetic field applied along the 𝑐 axis, five additional magnetic transitions occur, evidenced by magnetization and resistivity data, before the moment saturates at 2.62 𝜇 B /U at 2 K and ≥ 13.6T. In two magnetic phase regions, the Hall resistivity of UNb 6⁢ Sn 6 significantly deviates from the magnetization, suggesting that the phases have a large Berry curvature or a change in the Fermi surface. The unknown magnetic ordering of the field-dependent phases of UNb 6⁢ Sn 6 demonstrates the complexity of the 5⁢𝑓−4⁢𝑑 166 system and encourages further study of its properties.

36 MATERIALS SCIENCE↗