Concentration-Driven Self-Assembly of PS- b -PLA Bottlebrush Diblock Copolymers in Solution
Not Available
Patel, Bijal B.↗
SEARCH · Search NASA
Results for “PLA”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A chemical approach for the future of PLA upcycling: from plastic wastes to new 3D printing materials
As the demand for PLA increases, post-consumer disposal strategies must be carefully considered. While we would love to embrace a bioplastic future, we also need to tread carefully. Though PLA is widely claimed to be biodegradable, full degradation often requires conditions not typically found in landfills or industrial composting. Therefore, it will negatively impact the environment if treated carelessly. Here, in this work, we report a simple PLA upcycling path to turn existing PLA wastes into new 3D printable materials within 48 hours. The ester bonds of PLA can be cleaved efficiently via aminolysis. The obtained monomeric compound was derivatized with methacrylic anhydride, which introduces double bonds and thus a cross-linkable monomer is obtained. In combination with a comonomer and initiator, a photocurable resin is produced. The resin can be fed into any commercially available photocuring 3D printer. The 3D printed parts derived from PLA wastes exhibit impressive performances with a tensile strength of 58.6 MPa, Young's modulus of 2.8 GPa, and glass transition at ~180 °C. Our work demonstrates a new route to active upcycling of PLA while minimizing the need for disposal.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
PLA Renewable Bio Polymer Based Solid-State Gamma Radiation Detector-Dosimeter for Biomedical and Nuclear Industry Applications
Polylactic acid (PLA) as a “green,” renewable corn-soy based polymer resin was assessed as a novel solid-state detector for rapid-turnaround gamma radiation dosimetry in the 1–100 kGy range–of significant interest in biomedical and general nuclear industry applications. Co-60 was used as the source of gamma photons. It was found that PLA resin responds well in terms of rheology and porosity metrics with an absorbed gamma dose (Dg). In this work, rheological changes were ascertained via measuring the differential mass loss ratio (MLR) of irradiated PLA placed within PTFE-framed (40 mm × 20 mm × 0.77 mm) cavities bearing ~0.9 g of PLA resin and pressed for 12–16 min in a controlled force hot press under ~6.6 kN loading and platens heated to 227 °C for the low Dg range: 0–11 kGy; and to 193 °C for the extended Dg range: 11–120 kGy. MLR varied quadratically from 0.05 to ~0.2 (1σ ~ 0.007) in the 0–11 kGy experiments, and from 0.05 to ~0.5 (1σ ~0.01) in the 0–120 kGy experiments. Rheological changes from gamma irradiation were modeled and simultaneously correlated with void-pocket formations, which increase with Dg. A single PLA resin bead (~0.04 g) was compressed 5 min at 216 °C in 0–16 kGy experiments, and compressed 2 min at 232 °C in the 16–110 kGy experiments, to form sturdy ~100 µm thick wafers in the same press. Aggregate coupon porosity was then readily measurable with conventional optical microscope imaging and analyzed with standard image processing; this provided complementary data to MLR. Average porosity vs. dose varied quadratically from ~0 to ~15% in the 0–16 kGy range and from ~0 to ~18% over the 16–114 kGy range. These results provide evidence for utilizing “green”/renewable (under $0.01) PLA resin beads for rapid and accurate (+/-5–10%) gamma dosimetry over a wide 0–120 kGy range, using simple to deploy mass and void measuring techniques using common laboratory equipment.
61 RADIATION PROTECTION AND DOSIMETRY↗
Functional Filaments: Creating and Degrading pH-Indicating PLA Filaments for 3D Printing
With the rapid pace of advancements in additive manufacturing and techniques such as fused filament fabrication (FFF), the feedstocks used in these techniques should advance as well. While available filaments can be used to print highly customizable parts, the creation of the end part is often the only function of a given feedstock. In this study, novel FFF filaments with inherent environmental sensing functionalities were created by melt-blending poly(lactic acid) (PLA), poly(ethylene glycol) (PEG), and pH indicator powders (bromothymol blue, phenolphthalein, and thymol blue). The new PLA-PEG-indicator filaments were universally more crystalline than the PLA-only filaments (33–41% vs. 19% crystallinity), but changes in thermal stability and mechanical characteristics depended upon the indicator used; filaments containing bromothymol blue and thymol blue were more thermally stable, had higher tensile strength, and were less ductile than PLA-only filaments, while filaments containing phenolphthalein were less thermally stable, had lower tensile strength, and were more ductile. When the indicator-filled filaments were exposed to acidic, neutral, and basic solutions, all filaments functioned as effective pH sensors, though the bromothymol blue-containing filament was only successful as a base indicator. The biodegradability of the new filaments was evaluated by characterizing filament samples after aging in soil and soil slurry mixtures; the amount of physical deterioration and changes in filament crystallinity suggested that the bromothymol blue filament degraded faster than PLA-only filaments, while the phenolphthalein and thymol blue filaments saw decreases in degradation rates.
36 MATERIALS SCIENCE↗
Polylactic acid (PLA)-based multifunctional and biodegradable nanocomposites and their applications
Polylactic acid (PLA)-based nanocomposites are emerging as multifunctional, biodegradable materials, offering sustainable alternatives to petroleum-based plastics. This review examines recent advancements in PLA nanocomposites, focusing on enhanced mechanical strength, thermal stability, and biodegradability achieved through nanofillers like metallic particles, carbon-based materials, and ceramics. Techniques such as in situ polymerization, melt mixing, and electrospinning enable application-specific improvements. PLA's limitations, including brittleness and low barrier properties, are addressed to support diverse applications: in packaging (e.g., extended shelf life), biomedicine (e.g., degradable implants), and electronics (e.g., flexible devices). Despite challenges with filler dispersion and thermal resistance, continued innovations expand PLA's potential across multiple industries, contributing to a sustainable, circular economy.
Biodegradable polymers↗
Development of Antimicrobial PLA Composites for Fused Filament Fabrication
In addition to possessing the desirable properties of being a biodegradable and biocompatible polymer fabricated from renewable resources, poly (lactic acid) (PLA) has useful mechanical and thermal attributes that has enabled it to be one of the most widely-used plastics for medicine, manufacturing, and agriculture. Yet, PLA composites have not been heavily explored for use in 3D-printing applications, and the range of feasible materials for the technology is limited, which inhibits its potential growth and industry adoption. In this study, tunable, multifunctional antimicrobial PLA composite filaments for 3D-printing have been fabricated and tested via chemical, thermal, mechanical, and antimicrobial experiments. Thermally stable antimicrobial ceramics, ZnO and TiO2, were used as fillers up to 30 wt%, and poly (ethylene glycol) (PEG) was used as a plasticizer to tune the physical material properties. Results demonstrate that the PLA composite filaments exhibit the thermal phase behaviors and thermal stability suitable for 3D-printing. Additionally, PEG can be used to tune the mechanical properties while not affecting the antimicrobial efficacy that ZnO and TiO2 imbue.
TiO2↗
Tensile properties of 3D-printed wood-filled PLA materials using poplar trees
Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.
36 MATERIALS SCIENCE↗
High-Strength Polylactic Acid (PLA) Biocomposites Reinforced by Epoxy-Modified Pine Fibers
The stiffness and tensile strength of biopolymers (e.g., polylactic acid (PLA)) are less than desirable for load-bearing applications in their neat form. The use of natural fibers as reinforcements for composites (for large-scale three-dimensional (3D) printing) has expanded rapidly, attributable to their low weight, low cost, high stiffness, and renewable nature. Silane and acid/alkali are typically used to modify the surface of natural fibers to improve the fiber/polymer interfacial adhesion. In this study, a simple method of impregnation was developed to modify pine fibers (loblolly, mesh size of 90–180 μm, 30 wt %) with a solvent-borne epoxy to reinforce PLA. As a benefit of the epoxy modification (0.5–10 wt %), the tensile strengths and Young’s moduli of the epoxy-modified pine/PLA composites increased by up to 20 and 82%, respectively, as compared to that of neat PLA. Furthermore, the epoxy-modified pine/PLA composites, with an optimum epoxy modification (1.0 wt %), had fewer voids on the fracture surface as compared with pine/PLA composites without the modification of pine fibers via epoxy. Finally, results confirmed that epoxy partially penetrated the pore/hollow inner structures of pine fibers and improved the fiber/matrix interfacial adhesion. Epoxy modification is found to be a simple and effective technique to improve the properties of biocomposites.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Effects of chemical composition and physicochemical properties of poplar biomass on the performance of 3D printed poplar-reinforced PLA materials
Lignocellulosic biomass has been well-acknowledged as a filler for making 3D printed composites. The technical performances of composites were influenced by the characteristics of the components. The correlations between poplar biomass properties and the mechanical and thermal performances of the 3D printed poplar-plastic composites were investigated. The characteristics of poplar were modified by different pretreatment methods, including using hot water, dilute acid, and organic solvent (organosolv), and each treated poplar biomass was applied as a filler in a polylactic acid (PLA) polymer matrix to produce eco-friendly materials. These solvent pretreatments increased the hydrophobicity and surface area of poplar. Organosolv treated poplar showed the highest cellulose content and significantly increased Young's modulus of its biocomposites. Principal component analysis revealed that the specific surface area and water contact angle of biomass contributed to the thermal stability of biocomposites. Additionally, the degree of polymerization of cellulose and xylan content within the biomass correlated with the biocomposites' break stress. Notably, the crystallinity of biocomposites impacted the modulus of these materials. The reported relationships between biomass characteristics and 3D printed composite behaviors provide guidance for optimizing biomass processing in biocomposite applications.
Ji, Anqi [State Univ. of New York (SUNY), Syracuse↗
Additively Manufactured Carbon Fiber and Fused Deposition Modeling PLA Interlaminar Shear Testing Report
This test report summarizes the torsional test setup, procedure, and results for interlaminar shear (ILS) failure of additively manufactured carbon fiber (CFAM) material developed at LLNL. In addition, the report also includes testing of fused deposition modeled (FDM) polylactic acid (PLA), including ILS test standard D7078 and the same torsional test mentioned above. The test hopes to characterize ILS properties of CFAM, however substantial further testing and improvements still need to be done to induce a proper failure mode. This testing was performed by Sundi Win as part of her summer internship project in Kinetic Technologies.
36 MATERIALS SCIENCE↗
Additive Manufacturing of Lightweight Structures: Microfibrillated Cellulose – PLA Biofoams
Extrusion-based polymer additive manufacturing (AM) technology is growing rapidly. The introduction of fiber reinforced feedstock materials and recent developments in the manufacturing systems have promulgated large scale AM of composites to create new industries and applications. Synthetic fibers such as carbon and glass fibers are commonly used to reinforce polymer composites. However, increasing environmental and long-term sustainability concerns are leading to new materials using cellulose fiber reinforcement in bio-derived polymers. These materials offer new property sets, new supply chains and have the potential to provide economical solutions leading to new applications. Large scale AM can be attractive for many different applications because of its ability to freeform manufacture complex geometries; each application may require different material properties. One of the novel application areas for large scale AM is 3D printing of lightweight materials via foaming. Although achieving low density is the key in light weighting via foaming, mechanical performance is also important for many applications. In this study the impact of micro-cellulose fibers (MFC) on foaming behavior and the mechanical properties of additively manufactured parts is investigated. MFC-polylactic acid (PLA) feedstock pellets were prepared at varying MFC content (5, 10, 15 and 20 wt.%) to understand the impact of cellulose fiber content on density and mechanical properties of the AM biocomposites. Also, the impact of extrusion speed and foaming agent content on the AM biocomposites is investigated. Although achieving uniform printed foam structure is challenging with the presence of cellulose fibers, promising results were accomplished with density values below 0.5g/cm3.
Tekinalp, Halil↗
Green composites fabricated from bacteria retted bast fiber and PLA for light weight vehicle components
Explore the source record for details and available documents.
36 MATERIALS SCIENCE↗
Development of red-light cleavable PEG-PLA nanoparticles as delivery systems for cancer therapy
Not Available
Dariva, Camila G.↗
Strengthening polylactic acid (PLA) composites with poly(methyl methacrylate)-functionalized cellulose nanofibrils created through grafting-through emulsion polymerization
Aqueous surfactant free emulsion grafting-through polymerization produced poly(methyl methacrylate) coated cellulose nanofibrils that retained microstructure and strengthened poly(lactic acid) composites.
Senkum, Hathaithep↗
Life cycle analysis of polylactic acids from different wet waste feedstocks
Producing a valuable chemical product through diversion of wet wastes can simultaneously resolve the problems associated with increasing wastes and greenhouse gas emissions from conventional chemical production processes. In this work, we investigated the life-cycle greenhouse gas emissions, water, and fossil-fuel consumption for waste-derived polylactic acids (PLA) from three different waste feedstocks, namely wastewater sludge, food waste, and swine manure, using the Greenhouse Gases, Regulated Emissions, and Energy Use in Technologies (GREET) model. The decarbonization potential of replacing fossil-based resins with the waste-derived polymer was also investigated. The results show that swine manure-to-PLA pathway was the least carbon intensive (—1.4 kgCO 2 e/kg) among the three waste-to-PLA pathways on a cradle-to-grave basis, followed by the food waste case (—1.3 kgCO 2 e/kg) and then by the wastewater sludge case (0.6 kgCO 2 e/kg). In the baseline scenario, all three waste-to-PLA pathways were less carbon intensive than both fossil-based PET and HDPE on a cradle-to-grave basis: 66% (vs. PET) and 56% (vs. HDPE), 171 and 192%, 181 and 205% reduction in GHG emissions for wastewater sludge-, food waste-, and swine manure-to-PLA pathway, respectively. For all sensitivity cases investigated, the food waste- and swine manure-to-PLA pathways were significantly less carbon intensive than their fossil-counterparts. In terms of the annual decarbonization potential of replacing fossil-based PET or HDPE, the wastewater sludge- and food waste-pathway showed higher mitigation potential than the swine manure-pathway: i) 18–28 kilotons CO 2 e-reduction per year for wastewater sludge pathway; ii) 23–26 kTCO 2 e-reduction/yr for food waste pathway; and iii) about 5 kTCO 2 e-reduction/yr for swine manure pathway depending on the type of conventional resin replaced. However, given the abundant availability of the swine manure feedstocks across the United States, the decarbonization potential of swine manure-based pathway can also increase as the plant capacity or the number of plants grow.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Influence of plasticizers on thermal and mechanical properties of biocomposite filaments made from lignin and polylactic acid for 3D printing
Polylactic acid (PLA) and organosolv lignin were mixed at different ratios and extruded to obtain PLA-lignin composite filaments. PLA was replaced with lignin up to 20 wt%. Two plasticizers (polyethylene glycol (PEG) 2000 and struktol TR451) were added in varying concentrations to enhance the properties of PLA_L20 (20% lignin in PLA) composite filaments. Furthermore, the effect of lignin in PLA, and PEG, and struktol in PLA_L20 composites was investigated via tensile test, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, Fourier transform infrared spectroscopy of the filaments, and dynamic mechanical analysis of 3D printed samples. A 2 wt% PEG was able to enhance both tensile stress and elongation at maximum load of PLA_L20 composite by 19% and 35%, respectively, whereas struktol TR451 was able to improve elongation at maximum load by 24%.
3D printing↗
A Combined Thermochemical and Microbial Process for Recycling Polylactic Acid Polymer to Optically Pure L-Lactic Acid for Reuse
Polylactic acid polymer (PLA) produced from renewable resources can be recycled at the end of life to constituent monomer, optically pure lactic acid (LA), by a combination of chemical and biological processes. Efficient application of this closed loop of LA-PLA plastics-LA can minimize accumulation of plastics waste that pollute land and oceans. Temperature-dependent hydrolysis of PLA in water to LA follows apparent first order decay kinetics after a short lag. A modified Gompertz equation can explain the overall hydrolysis process. Alkali increased the rate of hydrolysis of PLA and reduced the length of lag period compared to water alone. The stoichiometry of base added to LA released was 1.0. The highest lactic acid yield was 0.95 g g -1 of PLA. D-LA in the syrup obtained after hydrolysis of PLA-plastics was removed using an engineered Escherichia coli to produce a L-LA syrup with an optical purity ≥ 99%. Here, these results show that thermochemical hydrolysis of PLA-based plastics to LA with optimum amount of base followed by bio-based purification to L-LA is an effective method of recycling PLA-plastics for reuse.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗