Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLANFORM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Planform effects for low-fineness ratio multibody configurations at supersonic speeds

An experimental and theoretical investigation of planform effects on a low-fineness ratio multibody configuration has been conducted in NASA Langley Research Center's Unitary Plan Wind Tunnel at Mach numbers 1.6, 1.8, 2.0, and 2.16. Experimental and theoretical values of lift, drag, and pitching moment were obtained on three configurations which varied in outboard panel planform only. The three variations were at 65 deg delta, a 70/66 deg cranked arrow, and a 20 deg trapezoidal planform . The purpose of the study was to determine the effect of wing planform on the supersonic aerodynamics and to evaluate the ability of two existing linearized-theory aerodynamic methods to predict these effects. Experimental data showed that the planforms produced the lift, drag-due-to-lift, and pitching-moment characteristics typically found on single-body configurations. However, the data also showed that planform has a minimal influence on zero-lift drag, which is not typical of single-body configurations. Theoretical aerodynamic analysis indicated that codes based on linearized theory adequately predicted the effect of planform on the supersonic aerodynamics.

Mcmillin, S. N.↗
NASA NTRS1961

Effects of Canard Planform and Wing-Leading-Edge Modification on Low-Speed Longitudinal Aerodynamic Characteristics of a Canard Airplane Configuration

An investigation has been conducted at low subsonic speeds to study the effects of canard planform and wing-leading-edge modification on the longitudinal aerodynamic characteristics of a general research canard airplane configuration. The basic wing of the model had a trapezoidal planform, an aspect ratio of 3.0, a taper ratio of 0.143, and an unswept 80-percent-chord line. Modifications to the wing included addition of full-span and partial-span leading-edge chord-extensions. Two canard planforms were employed in the study; one was a 60 deg sweptback delta planform and the other was a trapezoidal planform similar to that of the basic wing. Modifications to these canards included addition of a full-span leading-edge chord-extension to the trapezoidal planform and a fence to the delta planform. For the basic-wing-trapezoidal-canard configuration, rather abrupt increases in stability occurred at about 12 deg angle of attack. A slight pitch-up tendency occurred for the delta-canard configuration at approximately 8 deg angle of attack. A comparison of the longitudinal control effectiveness for the basic-wing-trapezoidal-canard combination and for the basic-wing-delta-canard combination indicates higher values of control effectiveness at law angles of attack for the trapezoidal canard. The control effectiveness for the delta-canard configuration, however, is seen to hold up for higher canard deflections and to higher angles of attack. Use of a full-span chord-extension deflected approximately 30 deg on the trapezoidal canard greatly improved the control characteristics of this configuration and enabled a sizeable increase in trim lift to be realized.

Spencer, Bernard, Jr.↗
NASA NTRS1992

Effect of planform and body on supersonic aerodynamics of multibody configurations

An experimental and theoretical investigation of the effect of the wing planform and bodies on the supersonic aerodynamics of a low-fineness-ratio, multibody configuration has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Force and moment data, flow-visualization data, and surface-pressure data were obtained on eight low-fineness-ratio, twin-body configurations. These configurations varied in inboard wing planform shape, outboard wing planform shape, outboard wing planform size, and presence of the bodies. The force and moment data showed that increasing the ratio of outboard wing area to total wing area or increasing the leading-edge sweep of the inboard wing influenced the aerodynamic characteristics. The flow-visualization data showed a complex flow-field system of shocks, shock-induced separation, and body vortex systems occurring between the side bodies. This flow field was substantially affected by the inboard wing planform shape but minimally affected by the outboard wing planform shape. The flow-visualization and surface-pressure data showed that flow over the outboard wing developed as expected with changes in angle of attack and Mach number and was affected by the leading-edge sweep of the inboard wing and the presence of the bodies. Evaluation of the linear-theory prediction methods revealed their general inability to consistently predict the characteristics of these multibody configurations.

Mcmillin, S. Naomi↗
NASA NTRS1981

Effects of Horizontal-Control Planform and Wing-Leading-Edge Modification on Low-Speed Longitudinal Aerodynamic Characteristics of a Canard Airplane Configuration

An investigation at low subsonic speeds has been conducted in the Langley 300-MPH 7- by 10-foot tunnel. The basic wing had a trapezoidal planform, an aspect ratio of 3.0., a taper ratio of 0.143, and an unswept 80-percent-chord line. Modifications to the basic wing included deflectable full-span and partial-span leading-edge chord-extensions. A trapezoidal horizontal control similar in planform to the basic wing and a 60 deg sweptback delta horizontal control were tested in conjunction with the wing. The total planform area of each horizontal control was 16 percent of the total basic-wing area. Modifications to these horizontal controls included addition of a full-span chord-extension to the trapezoidal planform and a fence to the delta planform.

Spencer, Bernard, Jr.↗
NASA NTRS1999

Investigation of Vortex Flaps and Other Flow Control Devices on Generic High-Speed Civil Transport Planforms

A parametric cranked delta planform study has been conducted in the Langley 14- by 22-Foot Subsonic Tunnel with the following objectives: (1) to evaluate the vortex flap design methodology for cranked delta wings, (2) to determine the influence of leading-edge sweep and the outboard wing on vortex flap effectiveness, (3) to evaluate novel flow control concepts, and (4) to validate unstructured grid Euler computer code predictions with modeled vortex and trailing-edge flaps. Two families of cranked delta planforms were investigated. One family had constant aspect ratio, while the other had a constant nondimensional semispan location of the leading-edge break. The inboard leading-edge sweep of the planforms was varied between 68 deg., 71 deg., and 74 deg., while outboard leading-edge sweep was varied between 48 deg. and 61 deg. Vortex flaps for the different planforms were designed by an analytical vortex flap design method. The results indicate that the effectiveness of the vortex flaps was only slightly influenced by the variations in the parametric planforms. The unstructured grid Euler computer code was successfully used to model the configurations with vortex flaps. The vortex trap concept was successfully demonstrated.

Kjerstad, Kevin J.↗
DOE OSTI2021

Floodplain Wetland Channel Planform, Cross-Sectional Morphology, and Sediment Characteristics Along an Estuarine to Tidal River Gradient

The formation of wetland channel networks on coastal river floodplains is affected by spatial transitions in tidal-fluvial processes. This study evaluated sedimentation patterns in tidal marshes on the 147-km tidal Columbia River and its 87-km estuary and characterized the cross-sectional geometry and planform morphometry of tidal wetlands along the estuarine to riverine gradient. Tidal marshes were predominantly depositional (median 0.7 cm yr-1, primarily silt), consistent with late-Holocene rates. Marsh sediment accretion rate increased with annual maximum 7-day average daily maximum water depth. Elevation was negatively correlated with accretion rate in the tidal river and positively correlated with total organic carbon (TOC%) in the tidal river and estuary. TOC% was greater in the estuary and, like percent fines, greater farther from the main-channel Columbia River. For four single-channel and six channel-network planforms of tidal marsh, shrub-dominated, and forested wetlands: (1) Spatial patterns of cross-sectional morphology conformed to typical coastal wetland morphology in estuarine reaches up to the tidal river. (2) Reach-based and common slope linear models for channel perimeter on wetland area were predictive in the estuary (R2 > 0.81) and differed between island (n = 144) and mainland (n = 164) wetlands. No planform linear models were predictive for the entire study area or the tidal river. No models for channel outlets were acceptable. (3) Channel perimeter, surface area, and outlets were all highly variable within and among estuarine–riverine reaches. Analyses of sediment, cross-section, and planform support the use of a “natural network paradigm” for wetland-restoration design on tidal river floodplains.

channel morphology↗
NASA NTRS1981

Development of an efficient procedure for calculating the aerodynamic effects of planform variation

Numerical procedures to compute gradients in aerodynamic loading due to planform shape changes using panel method codes were studied. Two procedures were investigated: one computed the aerodynamic perturbation directly; the other computed the aerodynamic loading on the perturbed planform and on the base planform and then differenced these values to obtain the perturbation in loading. It is indicated that computing the perturbed values directly can not be done satisfactorily without proper aerodynamic representation of the pressure singularity at the leading edge of a thin wing. For the alternative procedure, a technique was developed which saves most of the time-consuming computations from a panel method calculation for the base planform. Using this procedure the perturbed loading can be calculated in about one-tenth the time of that for the base solution.

Mercer, J. E.↗
NASA NTRS1980

Blade planform for a quiet helicopter

The effects of blade planform and tip speed on noise and performance for a Hughes 500 C rotor system were studied. A cursory examination of the effects of such planform shapes as regular, inverse, and no taper on the noise and performance of the rotor was conducted. It was found that a constant width wide chord planform at tower tip speed provided the best performance and lowest noise. The tapered planforms had lower performance figures due to the reduced solidity. However, some noise reductions were achieved.

Ram, D. S. J.↗
NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗
NASA NTRS1987

An experimental study of the aerodynamic characteristics of planar and non-planar outboard wing planforms

A series of wind tunnel experiments have been conducted to investigate the aerodynamic characteristics of several planar and nonplanar wingtip planforms. Seven different configurations: base-line rectangular, elliptical, swept and tapered, swept and tapered with dihedral, swept and tapered with anhedral, rising arc, and drooping arc, were investigated for two different spans. The data are available in terms of coefficient plots of force data, flow visualization photographs, and velocity and pressure flowfield surveys. All planforms, particularly the nonplanar, have some advantages over the baseline rectangular planform. Span efficiencies up to 20-percent greater than baseline are a possibility. However, it is suggested that the span efficiency concept might need refinement for nonplanar wings. Flow survey data show the change in effective span with vortex roll-up. The flow visualization shows the occurrence of mushroom-cell-separation flow patterns at angles of attack corresponding to stall. These grow with an increase in post-stall angle of attack. For the larger aspect ratios, the cells are observed to split into sub-cells at the higher angles of attack. For all angles of attack, some amount of secondary vortex flow is observed for the planar and nonplanar out-board planforms with sweep and taper.

Naik, D. A.↗
NASA NTRS1987

Planform effects on the supersonic aerodynamics of multibody configurations

An experimental and theoretical investigation of the effect of planform on the supersonic aerodynamics of low-fineness-ratio multibody configurations was conducted. Longitudinal and lateral-directional aerodynamic and flow visualization data were obtained on three multibody configurations. The data indicated that planform has a small effect on the zero lift drag of a multibody configuration. The longitudinal data obtained at lifting conditions showed a sensitivity to planform shape. Lateral-directional data obtained for all configurations did not uncover any unusual stability traits for this class of configuration. A comparison study was also made between the planform effects observed on single-body and multibody configurations. Results from this study indicate that the multibody concept appears to offer a mechanism for employing a low-sweep wing with no significant increase in zero-lift drag but still retaining high-performance characteristics at high-lift conditions. Evaluation of the linear-theory prediction methods revealed a general inability of the methods to predict the characteristics of low-fineness-ratio geometries.

Mcmillin, Naomi↗
NASA NTRS1992

Effect of blade planform variation on the forward-flight performance of small-scale rotors

An investigation was conducted in the Glenn L. Martin Wind Tunnel to determine the effect of blade planform variation on the forward-flight performance of four small-scale rotors. The rotors were 5.417 ft in diameter and differed only in blade planform geometry. The four planforms were: (1) rectangular; (2) 3:1 linear taper starting at 94 percent radius; (3) 3:1 linear taper starting at 75 percent radius; and (4) 3:1 linear taper starting at 50 percent radius. Each planform had a thrust-weighted solidity of 0.098. The investigation included forward-flight simulation at advance ratios from 0.14 to 0.43 for a range of rotor lift and drag coefficients. Among the four rotors, the rectangular rotor required the highest torque for the entire range of rotor drag coefficients attained at advanced ratios greater than 0.14 for rotor lift coefficients C sub L from 0.004 to 0.007. Among the rotors with tapered blades and for C sub L = 0.004 to 0.007, either the 75 percent tapered rotor or the 50 percent tapered rotor required the least amount of torque for the full range of rotor drag coefficients attained at each advance ratio. The performance of the 94 percent tapered rotor was generally between that of the rectangular rotor and the 75 and 50 percent tapered rotors at each advance ratio for this range of rotor lift coefficients.

Noonan, Kevin W.↗
NASA NTRS1995

Low-speed longitudinal aerodynamic characteristics through poststall for 21 novel planform shapes

To identify planform characteristics which have promise for a highly maneuverable vehicle, an investigation was conducted in the Langley Subsonic Basic Research Tunnel to determine the low-speed longitudinal aerodynamics of 21 planform geometries. Concepts studied included twin bodies, double wings, cutout wings, and serrated forebodies. The planform models tested were all 1/4-in.-thick flat plates with beveled edges on the lower surface to ensure uniform flow separation at angle of attack. A 1.0-in.-diameter cylindrical metric body with a hemispherical nose was used to house the six-component strain gauge balance for each configuration. Aerodynamic force and moment data were obtained across an angle-of-attack range of 0 to 70 deg with zero sideslip at a free-stream dynamic pressure of 30 psf. Surface flow visualization studies were also conducted on selected configurations using fluorescent minitufts. Results from the investigation indicate that a cutout wing planform can improve lift characteristics; however, cutout size, shape, and position and wing leading-edge sweep will all influence the effectiveness of the cutout configuration. Tests of serrated forebodies identified this concept as an extremely effective means of improving configuration lift characteristics; increases of up to 25 percent in the value of maximum lift coefficient were obtained.

Gatlin, Gregory M.↗
NASA NTRS1999

Serrated-Planform Lifting-Surfaces

A novel set of serrated-planform lifting surfaces produce unexpectedly high lift coefficients at moderate to high angles-of-attack. Each serration, or tooth, is designed to shed a vortex. The interaction of the vortices greatly enhances the lifting capability over an extremely large operating range. Variations of the invention use serrated-planform lifting surfaces in planes different than that of a primary lifting surface. In an alternate embodiment, the individual teeth are controllably retractable and deployable to provide for active control of the vortex system and hence lift coefficient. Differential lift on multiple serrated-planform lifting surfaces provides a means for vehicle control. The important aerodynamic advantages of the serrated-planform lifting surfaces are not limited to aircraft applications but can be used to establish desirable performance characteristics for missiles, land vehicles, and/or watercraft.

McGrath, Brian E.↗
NASA NTRS2011

Hybrid Wing Body Planform Design with Vehicle Sketch Pad

The objective of this paper was to provide an update on NASA s current tools for design and analysis of hybrid wing body (HWB) aircraft with an emphasis on Vehicle Sketch Pad (VSP). NASA started HWB analysis using the Flight Optimization System (FLOPS). That capability is enhanced using Phoenix Integration's ModelCenter(Registered TradeMark). Model Center enables multifidelity analysis tools to be linked as an integrated structure. Two major components are linked to FLOPS as an example; a planform discretization tool and VSP. The planform discretization tool ensures the planform is smooth and continuous. VSP is used to display the output geometry. This example shows that a smooth & continuous HWB planform can be displayed as a three-dimensional model and rapidly sized and analyzed.

Wells, Douglas P.↗
DOE OSTI2021

The effects of storms and a transient sandy veneer on the interannual planform evolution of a low-relief coastal cliff and shore platform at Sargent Beach, Texas, USA

Coastal cliff erosion is alongshore-variable and episodic, with retreat rates that depend upon sediment as either tools of abrasion or protective cover. However, the feedbacks between coastal cliff planform morphology, retreat rate, and sediment cover are poorly quantified. This study investigates Sargent Beach, Texas, USA, at the annual to interannual scale to explore (1) the relationship between temporal and spatial variability in cliff retreat rate, roughness, and sinuosity and (2) the response of retreat rate and roughness to changes in sand and shell hash cover of the underlying mud substrate as well as the impact of major storms using field measurements of sediment cover, erosion, and aerial images to measure shore platform morphology and retreat. A storm event in 2009 increased the planform roughness and sinuosity of the coastal cliff at Sargent Beach. Following the storm, aerial-image-derived shorelines with annual resolution show a decrease in average alongshore erosion rates from 12 to 4 m yr –1 , coincident with a decrease in shoreline roughness and sinuosity (smoothing). Like the previous storm, a storm event in 2017 increased the planform roughness and sinuosity of the cliff. Over shorter timescales, monthly retreat of the sea cliff occurred only when the platform was sparsely covered with sediment cover on the shore platform, indicating that the tools and cover effects can significantly affect short-term erosion rates. The timescale to return to a smooth shoreline following a storm or roughening event, given a steady-state erosion rate, is approximately 24 years, with the long-term rate suggesting a maximum of ~107 years until Sargent Beach breaches, compromising the Gulf Intracoastal Waterway (GIWW) under current conditions and assuming no future storms or intervention. The observed retreat rate varies, both spatially and temporally, with cliff face morphology, demonstrating the importance of multi-scale measurements and analysis for interpretation of coastal processes and patterns of cliff retreat.

58 GEOSCIENCES↗
NASA NTRS1974

Aerodynamic and flow visualization studies of variations in the geometry of irregular planform wings at a Mach number of 20.3

The longitudinal and summary lateral-directional stability characteristics have been obtained for a variety of irregular planform wings applied to a conceptual space shuttle orbiter. Three basic wing planforms with leading-edge sweep angles of 53.2 deg, 46.8 deg, and 35 deg were studied in conjunction with a series of inboard planform fillets with sweep angles up to 78 deg. The spanwise intersection point of the fillets and the basic wings was held constant. The data were obtained in the Langley 22-inch helium tunnel at a Mach number of 20.3 and a Reynolds number of 2.10 million based on model length. Model angle-of-attack range was from 0 deg to 54 deg at sideslip angles of 0 deg and minus 3.8 deg. Also included are results of a flow-visualization study consisting of electron-beam-illuminated flow and surface oil-flow patterns.

Stone, D. R.↗
NASA NTRS1976

Low subsonic aerodynamic characteristics of five irregular planform wings with systematically varying wing fillet geometry tested in the NASA/Ames 12 foot pressure tunnel (LA65)

An experimental and analytical aerodynamic program to develop predesign guides for irregular planform wings (also referred to as cranked leading edge or double delta wings is reported; the benefits are linearization of subsonic lift curve slope to high angles of attack and avoidance of subsonic pitch instabilities at high lift by proper tailoring of the planform-fillet-wing combination while providing the desired hypersonic trim angle and stability. Because subsonic and hypersonic conditions were the two prime areas of concern in the initial application of this program to optimize shuttle orbiter landing and entry characteristics, the study was designated the Subsonic/Hypersonic Irregular Planforms Study (SHIPS).

Ball, J. W.↗