Search NASA⌕ Search

SEARCH · Search NASA

Results for “POLISH ORGANIZATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Life support systems for Mars transit

The structural elements of life-support systems are reviewed in order to assess the suitability of specific features for use during a Mars mission. Life-support requirements are estimated by means of an approximate input/output analysis, and the advantages are listed relating to the use of recycling and regeneration techniques. The technological options for regeneration are presented in categories such as CO2 reduction, organics removal, polishing, food production, and organics oxidation. These data form the basis of proposed mission requirements and constraints as well as the definition of what constitutes an adequate reserve. Regenerative physical/chemical life-support systems are championed based exclusively on the mass savings inherent in the technology. The resiliency and 'soft' failure modes of bioregenerative life-support systems are identified as areas of investigation.

Macelroy, R. D.↗

Fast-Neutron Source Based on Plasma-Focus Device

This paper describes investigations of neutrons produced by small plasma focus device PF-6 operating in the Institute of Plasma Physics and Laser Microfusion, Warsaw, Poland. Main parameters of neutron radiation have been measured by scintillation probe, and by activation technique. Current derivative probe has also been applied to measure dI/dt signal. Simultaneously neutron transport calculations have been carried out by Monte Carlo method. Finally, experimental measurements and numerical calculations have allowed concluding that plasma focus devices can be useful pulse neutron sources for different applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser induced damage of fused silica polished optics due to a droplet forming organic contaminant

We report on the effect of organic molecular contamination on single shot laser induced damage density at the wavelength of 351 nm, with a 3 ns pulse length. Specific contamination experiments were made with dioctylphthalate (DOP) in liquid or gaseous phase, on the surface of fused silica polished samples, bare or solgel coated. Systematic laser induced damage was observed only in the case of liquid phase contamination. Different chemical and morphological characterization methods were used to identify and understand the damage process. We demonstrate that the contaminant morphology, rather than its physicochemical nature, can be responsible for the decrease of laser induced damage threshold of optics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advancing Cross-Sectional Scanning Electron Microscopy of Perovskite Solar Cells

Organic–inorganic perovskites are an emerging class of photovoltaic materials. Despite achieving power conversion efficiencies surpassing 26%, the challenge of perovskite stability including degradation during exposure to operational conditions such as light, heat, humidity, water, oxygen, and electric fields is well known. Related, perovskite instability has limited high-resolution electron imaging and characterization techniques that can be used for understanding degradation mechanisms. Furthermore, we demonstrate perovskite device cross-section preparation using mechanical polishing in a water-free environment with cryogenic Ar ion milling. Scanning electron microscopy was then used in both backscattered electron and secondary electron imaging modes to obtain information about layer structure, grain aggregate structure, and compositional heterogeneity. Monte Carlo CASINO simulations inform optimum beam conditions and image acquisition parameters and the effects of accelerating voltage, dwell times, and frame averaging for practical image acquisition are reported.

14 SOLAR ENERGY↗

The membrane bioreactor (MBR): A hybrid technology for bioregenerative wastewater treatment and resource recovery in space

Extraplanetary surface habitat life support systems (LSS) on the Moon and Mars, as well as long-duration space travel, will require novel capabilities to withstand anticipated unique, harsh conditions. In order to provide safe, habitable environments for the crew, water purification and waste processing systems will be required to treat all sources of water (condensate, Sabatier, urine, hygiene, fecal, food waste) in order to achieve the necessary levels of recovery needed to sustain life over the long-duration missions. The ability to recycle organic wastes creates an opportunity to recover critical elements (e.g., C, H, O, N, P) for subsequent food production, water purification, and atmospheric regeneration. Bioregenerative systems mimic functions of nature in engineered systems, or bioreactors, utilizing combination of prokaryotes, eukaryotes and archaea. While these systems are commonly used on Earth for wastewater treatment, bioreactors for space travel face additional challenges. Terrestrial bioreactors often rely on gravitational settling of dense flocs and granules for cell retention. For micro- or partial-gravity environments, density differential alone will not be adequate for cell retention; a gravity-independent means for cell retention is crucial. The membrane bioreactor represents the state of the art in wastewater treatment. This hybrid system combines biological processes with membrane filtration to achieve performance beyond what each can accomplish individually. The complete cell retention in an MBR allows for the decoupling of hydraulic retention time (HRT) and solids retention time (SRT), which result in a high-thruput, compact, treatment system. The Bioregenerative Water Technology Team at NASA Kennedy Space Center and the University of South Florida has developed a bioregenerative platform based on the hybrid MBR technology. The overall architecture is compact, modular, flexible, and adaptable to mission evolutions. The main subsystems of the bioregenerative architecture include: 1) Anaerobic membrane bioreactor (AnMBR): Also termed the Organic processor assembly (OPA), the function of the AnMBR is to treat organic wastes such as fecal and food wastes. These wastes are characterized by a concentration of suspended solids comprised of carbohydrates, proteins and lipids. The assigned function of the AnMBR is to break down and covert suspended solids to biogas (methane, hydrogen and carbon dioxide), reduce effluent chemical oxygen demand (COD), liberate organically-bound nutrients, and remove pathogenic organisms. 2) Phototrophic membrane bioreactor (PMBR): The PMBR is comprised of a co-culture of microalgae and bacteria. The assigned function of the PMBR is to polish the permeate of the AnMBR to further remove dissolved organic carbon, manage nutrients (nitrogen transformation, load dampening), and perform air revitalization. 3) Food processor assembly (FPA): The FPA is a food production platform (prokaryotic or eukaryotic), fueled by outputs from the AnMBR, or PMBR. For the presentation, we will describe each step of the bioregenerative architecture, and present performance data from extended trials treating analog and real metabolic wastes.

Bioreactor↗

Optimal Design and Operation of a Solvent-Sorbent Hybrid Capture Process for Minimizing the Cost of High Capture

High capture can cause a significant increase in energy penalty if the appropriate technology/technologies are not utilized. The optimal technology for bulk capture is not necessarily the optimal technology for polishing capture (i.e., high extent of capture from the flue gas with very low partial pressure of CO2). This work investigates the use of MEA for bulk capture with the polishing capture being accomplished by a functionalized metal organic framework (MOF).

Kasturi, Pooja↗

Development of a proton-exchange membrane electrochemical reclaimed water post-treatment system

A single-cell electrochemical reactor that utilizes a proton exchange membrane (PEM) as a solid electrolyte is being investigated for posttreatment of reclaimed waste waters with low or negligible electrolyte content. Posttreatment is a final 'polishing' of reclaimed waste waters prior to reuse, and involves removing organic impurities at levels as high as 100 ppm to below 500 ppb total organic carbon (TOC) content to provide disinfection. The system does not utilize or produce either expendable hardware components or chemicals and has no moving parts. Test data and kinetic analysis are presented. The feasibility and application for water reclamation processes in controlled ecological environments (e.g., lunar/Mars habitats) are also presented. Test results show that the electrochemical single cell reactor provides effective posttreatment.

Kaba, Lamine↗

Ultrashort Pulsed Laser Treatment: A Novel Sterilization Method for Planetary Protection

Introduction: On missions seeking signs of potential life elsewhere in the solar system, we have an obligation not to bring our own Earthly life with us. Reducing the bioburden (number of living microbes) on spacecraft is therefore required by the COSPAR Policy on Planetary Protection to target bodies that are of interest for understanding the origins of life (such as Mars). The method of spacecraft sterilization predominantly used by NASA is Heat Microbial Reduction, which is typically incompatible with heat-sensitive components such as optics and electronics, and is expensive and time-consuming. Here, we present preliminary results on a novel method for spacecraft hardware sterilization: high-intensity ultrashort (femtosecond) pulsed laser illumination. Femtosecond lasers use extremely high photon fluxes (10^29 photons/sec*cm^2, ~0.03 J/cm^2) in extremely short pulses, which can inactivate even stress-tolerant microbial spores with minimal damage to the spacecraft surface. This rapid sterilization technique could be carried out in situ in a spacecraft assembly clean room using high-speed surface scanning, saving critical time and resources. It also can potentially remove or reduce debris from inactivated cells and spores. Methods: To develop optimal laser processing parameters for inactivating planetary protection-relevant organisms on metal surfaces, we inoculated 1-cm^2 mirror-polished aluminum coupons with Bacillus subtilis spores (2x10^5 spores/coupon) and tested the effect of several parameters, including pulse count and fluence. Sterilization effectiveness was measured by recovering spores using a PVA (polyvinyl acetate) peel and conducting serial dilution and plating for colony-forming units (CFUs). Results: Our results show that pulse count and fluence both affect sterilization effectiveness and that within a certain pulse count range, increasing fluence increases effectiveness. We have demonstrated the ability to reduce viable microbial counts by at least 10^-4. Future work will include testing higher abundances and different species of microorganisms, effectiveness on complex surfaces, compatibility with sensitive surfaces, and quantification of cell debris removal. Femtosecond pulsed laser illumination has the potential to provide dramatic savings in both cost and schedule over current methods of bioburden reduction to prevent forward contamination. It may also have the potential for use in surface sterilization of returned samples to prevent back contamination.

Planetary Protection; Lasers; Sterilization; Bacil↗

Ion-Deposited Polished Coatings

Polished, dense, adherent coatings relatively free of imperfections. New process consists of using broad-beam ion source in evacuated chamber to ion-clean rotating surface that allows grazing incidence of ion beam. This sputter cleans off absorbed gases, organic contaminants, and oxides of mirror surface. In addition to cleaning, surface protrusions sputter-etched away. Process particularly adaptable to polishing of various substrates for optical or esthetic purposes.

Banks, B. A.↗

Buffered Electrochemical Polishing of Niobium

The standard preparation of superconducting radio-frequency (SRF) cavities made of pure niobium include the removal of a 'damaged' surface layer, by buffered chemical polishing (BCP) or electropolishing (EP), after the cavities are formed. The performance of the cavities is characterized by a sharp degradation of the quality factor when the surface magnetic field exceeds about 90 mT, a phenomenon referred to as 'Q-drop.' In cavities made of polycrystalline fine grain (ASTM 5) niobium, the Q-drop can be significantly reduced by a low-temperature (? 120 °C) 'in-situ' baking of the cavity if the chemical treatment was EP rather than BCP. As part of the effort to understand this phenomenon, we investigated the effect of introducing a polarization potential during buffered chemical polishing, creating a process which is between the standard BCP and EP. While preliminary results on the application of this process to Nb cavities have been previously reported, in this contribution we focus on the characterization of this novel electrochemical process by measuring polarization curves, etching rates, surface finish, electrochemical impedance and the effects of temperature and electrolyte composition. In particular, it is shown that the anodic potential of Nb during BCP reduces the etching rate and improves the surface finish.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel Sorbent to Clean Up Biogas for CHPs

In this project, TDA Research Inc. (TDA) has developed low-cost (on a per unit volume of gas processed basis), high-capacity expendable sorbents that can remove both the H 2 S and organic sulfur species in biogas to the ppb levels. The proposed sorbents will operate downstream of a bulk desulfurization system as a polishing bed to provide an essentially sulfur-free gas to a fuel cell (or any other application that needs a completely sulfur-free feed). Our sorbents use a highly dispersed mixed metal oxides active phase with desired modifiers prepared over on a mesoporous support. The support structure allows the large organic sulfur compounds (such as the diethyl sulfide and dipropyl sulfide phases with a large kinetic diameter) to enter the sorbent pores so that they can be adsorbed and removed from the gas stream.

09 BIOMASS FUELS↗

Electrolytic Plasma Surface Polishing of Complex Components Produced by Selective Laser Melting

The applicability of electrolytic plasma surface polishing to complex components produced by selective laser melting (SLM) is analyzed. By electrolytic plasma polishing by electrolyte spraying, the surface quality of components produced by SLM may be improved. This technology is found to decrease the surface roughness from R{sub a} = 5.6 μm to 1.4 μm. The optimal pressure of the electrolyte jet is 0.02–0.05 MPa. At high pressures, the process becomes unstable. By electrolytic plasma polishing on the basis of electrolyte jets, uniform external and internal surface roughness of components produced by SLM may be ensured.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Magnetorheological finishing of chemical-vapor deposited zinc sulfide via chemically and mechanically modified fluids

In this study, we describe the anisotropy in the material removal rate (MRR) of the polycrystalline, chemical-vapor deposited zinc sulfide (ZnS).We define the polycrystalline anisotropy via microhardness and chemical erosion tests for four crystallographic orientations of ZnS: (100), (110), (111), and (311). Anisotropy in the MRR was studied under magnetorheological finishing (MRF) conditions. Three chemically and mechanically modified magnetorheological (MR) fluids at pH values of 4, 5, and 6 were used to test the MRR variations among the four single-crystal planes. When polishing the single-crystal planes and the polycrystalline with pH 5 and pH 6MR fluids, variations were found in the MRR among the four single-crystal planes and surface artifacts were observed on the polycrystalline material. When polishing the single-crystal planes and the polycrystalline with the modified MR fluid at pH 4, however, minimal variation was observed in the MRR among the four orientations and a reduction in surface artifacts was achieved on the polycrystalline material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High stored-energy breakdown tests on electrodes made of stainless steel, copper, titanium and molybdenum

IRFM have conducted resilience tests on electrodes made of Cu, stainless steel 304L, Ti and Mo against breakdowns up to 170 kV and 300 J. The tests of the 10×10 cm{sup 2} electrodes have been performed at an electrode distance d=11 mm under vacuum (P∼5×10{sup −6} mbar). No great difference in voltage holding between the materials could be identified; all materials could reach a voltage holding between 140 and 170 kV over the 11 mm gap, i.e. results scatter within a ±10% band. After exposure to ∼10000 seconds of high-voltage (HV) on-time, having accumulated ∼1000 breakdowns, the electrodes were inspected. The anodes were covered with large and small craters. The rugosity of the anodes had increased substantially, that of the cathodes to a lesser extent. The molybdenum electrodes are least affected, but this does not show in their voltage holding capability. It is hypothesized that penetrating high-energy electrons from the breakdown project heat below the surface of the anode and cause a micro-explosion of material when melting point is exceeded. Polished electrodes have also been tested. The polishing results in a substantially reduced breakdown rate in the beginning, but after having suffered a relatively small number (∼100) of breakdowns, the polished electrodes behaved the same as the unpolished ones.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diffusion-Limited Agglomeration and Defect Generation during Chemical Mechanical Planarization

Chemical mechanical planarization (CMP) of copper involves removal of surface asperities with abrasive particles and polishing processes. This leads to copper-containing nanoparticles extruded into the solution. We model the diffusion-limited agglomeration (DLA) of such nanoparticles which can rapidly grow to large sizes. These large particles are detrimental because they can participate in polishing, causing scratches and surface defects during CMP. The agglomeration is much slower in the reaction-limited agglomeration process. Under realistic conditions the defect generation probability can increase significantly over time scales of {approx}10 to 20 min from DLA, unless prevented by slurry rejuvenation or process modification measures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

First elliptical cavity fabricated with metallographic polishing

The development of an easy and inexpensive Nb sheet preparation process, based on metallographic polishing, has been presented earlier [1, 2]. The aim is to remove the damage layer caused by the rolling process on the sheet in order to reduce the length of surface treatment on completed cavities. The process has been applied on a QPR sample and tested in RF, without any surface chemistry. Its surface resistance is about 4 times lower than the EP baseline at 414 MHz, 2 K [3]. The first elliptical cavity based on this principle has been produced at KEK, starting with large polished sheets developed in collaboration between IJCLAB, and the company LAMPLAN. We present its 1st RF test at KEK, with a HF rinsing and a recrystallization treatment at 600C for 10h, without any chemical etching at first. References: *1: C. Antoine and R. Crooks, “Reducing Electropolishing Time with Chemical-Mechanical Polishing”, SRF2009. *2: O. Hryhorenko, et al., "An innovative approach of surface polishing for SRF cavity applications". Journal of Manufacturing and Materials Processing, 2023. 7(2): p. 62. *3: O. Hryhorenko, et al., "Recent advances in metallographic polishing for SRF application", SRF2023.

Dohmae, Takeshi [High Energy Accelerator Research ↗

Laser Processing of Metals and Polymers

A laser offers a unique set of opportunities for precise delivery of high quality coherent energy. This energy can be tailored to alter the properties of material allowing a very flexible adjustment of the interaction that can lead to melting, vaporization, or just surface modification. Nowadays laser systems can be found in nearly all branches of research and industry for numerous applications. Sufficient evidence exists in the literature to suggest that further advancements in the field of laser material processing will rely significantly on the development of new process schemes. As a result they can be applied in various applications starting from fundamental research on systems, materials and processes performed on a scientific and technical basis for the industrial needs. The interaction of intense laser radiation with solid surfaces has extensively been studied for many years, in part, for development of possible applications. In this thesis, I present several applications of laser processing of metals and polymers including polishing niobium surface, producing a superconducting phase niobium nitride and depositing thin films of niobium nitride and organic material (cyclic olefin copolymer). The treated materials were examined by scanning electron microscopy (SEM), electron probe microanalysis (EPMA), atomic force microscopy (AFM), high resolution optical microscopy, surface profilometry, Fourier transform infrared spectroscopy (FTIR) and x-ray diffraction (XRD). Power spectral density (PSD) spectra computed from AFM data gives further insight into the effect of laser melting on the topography of the treated niobium.

36 MATERIALS SCIENCE↗