Search NASA⌕ Search

SEARCH · Search NASA

Results for “POSITION SERVO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Analysis of the computed torque drive method and comparison with conventional position servo for a computer-controlled manipulator

A manipulator and its control system (modeled after a Stanford design) is being developed as part of an artificial intelligence project. This development includes an analytical study of the control system software. A comparison is presented of the computed torque method and the conventional position servo. No conclusion is made as to the perference of one system over the other, as it is dependent upon the application and the results of a sampled data analysis.

Markiewicz, B. R.↗
NASA NTRS1973

Magnetic particle clutch controls servo system

Magnetic clutches provide alternative means of driving low-power rate or positioning servo systems. They may be used over wide variety of input speed ranges and weigh comparatively little. Power drain is good with overall motor/clutch efficiency greater than 50 percent, and gain of clutch is close to linear, following hysteresis curve of core and rotor material.

Fow, P. B.↗
NASA NTRS1973

Servomechanism design techniques and applications - Aerospace problems.

Transistorized alternating-current servomechanisms for a basic position servo with rate feedback or network compensation are reviewed. Studies of optimum methods of control position variables in aerospace applications show that no single method is best for all cases. The optimum method is very much dependent upon available devices, generating sources, and load parameters. These are constraints difficult to identify for future aerospace missions. Design and application considerations are discussed, along with step-by-step design procedures. For illustration, specific design problems are used to exemplify the approach to solutions.

Lalli, V. R.↗
NASA NTRS1996

Modeling and analysis of the DSS-14 antenna control system

An improvement of pointing precision of the DSS-14 antenna is planned for the near future. In order to analyze the improvement limits and to design new controllers, a precise model of the antenna and the servo is developed, including a finite element model of the antenna structure and detailed models of the hydraulic drives and electronic parts. The DSS-14 antenna control system has two modes of operation: computer mode and precision mode. The principal goal of this investigation is to develop the model of the computer mode and to evaluate its performance. The DSS-14 antenna computer model consists of the antenna structure and drives in azimuth and elevation. For this model, the position servo loop is derived, and simulations of the closed-loop antenna dynamics are presented. The model is significantly different from that for the 34-m beam-waveguide antennas.

Gawronski, W.↗
NASA NTRS1996

Modeling and Analysis of the DSS-14 Antenna Control System

An improvement of pointing precision of the DSS-14 antenna is planned for the near future. In order to analyze the improvement limits and to design new controllers, a precise model of the antenna and the servo is developed, including a finite element model of the antenna structure and detailed models of the hydraulic drives and electronic parts. The DSS-14 antenna control system has two modes of operation: computer mode and precision mode. The principal goal of this investigation is to develop the model of the computer mode and to evaluate its performance. The DSS-14 antenna computer model consists of the antenna structure and drives in azimuth and elevation. For this model, the position servo loop is derived, and simulations of the closed-loop antenna dynamics are presented. The model is significantly different from that for the 34-m beam-waveguide antennas.

Gawronski, W.↗
NASA NTRS1968

Method of reducing time base error in digital magnetic recorders

Apparatus reduces Time Base Error /TBE/ in the playback of digital data from magnetic recording equipment. The apparatus uses a magnet which employs a servo position control of the tape by which the playback data clock is phase locked with a fixed frequency reference signal.

Moore, J. M.↗
NASA NTRS1970

Fluidic power control systems

Pneumatic and hydraulic fluidic power control systems, discussing moving part position servos and cold gas reaction systems

Rose, R. K.↗
NASA NTRS1982

Multivariable frequency domain controller for magnetic suspension and balance systems

The magnetic suspension and balance system for an airplane model in a large wind tunnel is considered. In this system, superconducting coils generate magnetic forces and torques on the magnetized soft iron core of the airplane model. The control system is a position servo where the airplane model, with six degrees of feedom, follows the reference static or dynamic input commands. The controller design, based on the characteristic loci method, minimizes the effects of aerodynamic and inertial cross-couplings, and provides the specified dynamic response.

Baheti, R. S.↗
NASA NTRS1986

Implementation and flight tests for the Digital Integrated Automatic Landing System (DIALS). Part 2: Complete set of flight data

Five flight tests of the Digital Automated Landing System (DIALS) were conducted on the Advanced Transport Operating System (ATOPS) Transportation Research Vehicle (TSRV)--a modified Boeing 737 Aircraft for advanced controls and displays research. These flight tests were conducted at NASA's Wallops Flight Center using the Microwave Landing System (MLS) installation on Runway 22. This report is primarily a collection of data plots of all performance variables recorded for the entire five flight tests. A description and source of the performance variables is included. Performance variables include inertial data, air data, automatic control commands, control servo positions, sensor data, DIALS guidance and control parameters, and Kalman filter data. This data illustrates low overshoot captures of the localizer for intercept angles of 20 deg, 30 deg, 40 deg, and 50 deg intercept angles, and low overshoot captures of the glideslope slope for 3 deg, 4.5 deg, and 5 deg glideslopes. Flare maneuvers were successfully performed from the various glideslope angles and good decrab maneuvers were performed in crosswinds of 6 knots. In 18 to 20 knot crosswind conditions rudder limiting occurred which caused lateral drifting although heading alignment was achieved.

Hueschen, R. M.↗
NASA NTRS1992

Task definition, decoupling and redundancy resolution by nonlinear feedback in multi-robot object handling

The problem of rigid object handling by multiple robot arms is investigated. The primary goal is to make the object exhibit a prescribed behavior while in contact with a fully known environment. Point contacts are assumed between the object and the arms. The aspect of task definition to achieve decoupling and linearizing control laws is discussed. Control laws are first formulated at the object level to provide decoupled force and position servo loops. It is then used to form control laws for the individual arms. Redundancies exist at the object and arm levels. The object level redundancy is used to achieve secondary goals in object handling. The arm level redundancies are the zero dynamics and can be controlled by redundant inputs. Full use of the available inputs are used to control the system as a whole. Numerical simulations for a dual-arm situation illustrate the validity of the approach.

Ramadorai, A. K.↗