Search NASA⌕ Search

SEARCH · Search NASA

Results for “PP fiber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Optimization of matrix viscosity improves polypropylene fiber dispersion and properties of engineered cementitious composites

Engineered cementitious composites (ECC) is a durable cementitious material with high tensile ductility and strain-hardening characteristics. Although considered as a cost-effective fiber for ECC, polypropylene (PP) fiber is reportedly difficult to disperse in mortar matrix due to its high aspect ratio and hydrophobicity. In this study, the matrix viscosity of a low-carbon ECC based on limestone calcined clay cement was tailored as a variable to improve PP fiber dispersion under a pre-determined mixing protocol. The effect of matrix viscosity on the composite fresh and hardened properties was investigated experimentally. Results suggested an optimal range of matrix viscosity (10.3–11.5 Pa . s) favors the composite tensile strength and strain capacity at 28 days. At the optimal state with a 0.1 % viscosity modifying admixture (VMA)-to-binder mass ratio, PP-ECC achieved 7.0 % tensile strain capacity and 3.5 MPa ultimate tensile strength. When matrix viscosity falls outside the desired range, both ultimate tensile strength and strain capacity were diminished. By tailoring the VMA dosage, the matrix viscosity can be adjusted for desired fiber dispersion, workability, and mechanical properties. Finally, the findings of this study provide a technical reference for the practical design and application of PP-ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of fiber sizing and glass fiber laminate hybridization on vibration damping and mechanical properties of banana fiber reinforced polypropylene composites

Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.

Banana fiber↗
DOE OSTI2023

Testing Various Cement Formulations under Temperature Cycles and Drying Shrinkage for Low-Temperature Geothermal Wells

Low-enthalpy geothermal wells are considered a sustainable energy source, particularly for district heating in the Netherlands. The cement sheath in these wells experiences thermal cycles. The stability of cement recipes under such conditions is not well understood. In this work, thermal cycling experiments for intermediate- and low-temperature geothermal well cements have been conducted. The samples were cured either under ambient conditions or under realistic pressure and temperature for 7 days. The samples did not show any signs of failure after performing 10 cycles of thermal treatment between 100 °C and 18 °C. We also tested cement formulations under drying conditions. Drying shrinkage is caused by a reduction in the water content of cement, which leads to capillary forces that can damage cement. Such circumstances lead to tensile stresses causing radial cracks. Most samples exhibited cracks under low humidity conditions (drying). Fiber reinforcement, especially using short PP fibers, improved the cement’s resilience to temperature and humidity changes. Such additives can improve the longevity of cement sheaths in geothermal wells.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)

Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

New Sesame Equations of State for Polypropylene, Polyvinylchloride (PVC), and Nylon 66

I built new Sesame equations of state (EOS) for polypropylene (PP), polyvinylchloride (PVC), and nylon 66. PP has the same stoichiometry as polyethylene and TPX but with a density intermediate between the two. Nylon is a polyamide manufactured chiefly in the form of fibers. PP and PVC are the second- and third-most widely produced polymers in the world. All three are thermoplastics. Their monomer units are depicted in Figure 1. I discuss the theory on which the EOS are based in the following section, then compare results to thermal and shock compression data in Section III.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Life cycle assessment of coir fiber-reinforced composites for automotive applications

Past decades have seen an increasing prevalence of natural fiber-reinforced composites (NFRCs) due to growing conscientiousness around sustainability and a push towards vehicle lightweighting. The environmentally friendly and sustainable claims of NFRCs need to be validated due to their large variability and variety, particularly where material substitutions are concerned, such as in substituting glass fiber with natural fiber. Additionally, the objective of this work is to determine the cumulative energy demand (CED) and greenhouse gas emissions (GHG) associated with an automotive part (of volume 0.001 m3) made from 40 wt% coir fiber-reinforced polypropylene (PP) and compared with a similar part made from 40 wt% glass fiber reinforced PP. SimaPro v. 9.0.0.49 was used for the analysis, whereas inventory data were collected from databases, such as Ecoinvent 3, Transportation Energy Databook, Greet model 2022, and published papers. The results showed that CED and GHG associated with the coir fiber-reinforced composite part were lower than the glass fiber-reinforced composite part for both cradle-to-gate (~34–40%) and cradle-to-grave (excluding end-of-life) (~24%) analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Long coir and glass fiber reinforced polypropylene hybrid composites prepared via wet-laid technique

Natural fiber composites offer an advantage in terms of weight saving for many automotive applications; however, many natural fiber composites lack properties to justify substitution for synthetic composites. Hybridizing the natural fiber composites by adding a fraction of synthetic fibers is an innovative approach to provide a balance between composite's performance and weight savings. In this study, coir fiber (40 wt%)-reinforced polypropylene (PP) composites were hybridized by substituting a fraction of coir fiber with glass fiber (0–30 wt%). The composites were prepared using a novel wet-laid technique followed by compression molding, where the fiber length is preserved. The composites prepared by hybridizing PP/coir fibers with glass fibers were light in weight (6–20% lighter compared to 40 wt% glass fiber reinforced PP) with significantly enhanced tensile (strength – 49–182%, modulus – 54–130%), flexural (strength – 41–104%, modulus – 64–193%), and impact properties (157 - 474%) compared to 40 wt% coir fiber reinforced PP composites. Furthermore, the addition of glass fiber (10–30 wt%) to coir fiber reduced the water-absorbing tendency (by 18–74%) of PP/coir fiber composites. All in all, this work has potential applications in automotive, mass transit, and truck applications where natural fiber composites are being investigated as alternatives to metal and/or fully synthetic composites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crack width control and mechanical properties of low carbon engineered cementitious composites (ECC)

Engineered Cementitious Composites (ECC) have superior properties with high tensile ductility and tight crack width compared to conventional concrete. The properties of ECC are significantly influenced by the material composition which can be tailored to enhance the sustainability of ECC. Towards this goal, recycled crumb rubber (CR) and silica fume (SF) were used to tailor the properties of a polypropylene-fiber reinforced ECC with a low carbon binder based on limestone calcined clay cement (LC3) in this study. Crumb rubber was found to be effective in enhancing strain-hardening performance and reducing the width of the multiple microcracks. However, a loss of compressive strength was accompanied by an increasing amount of CR. While silica fume or lower w/b ratio enhanced the compressive strength, the crack width of ECC increased at higher SF content or lower w/b. The underlying mechanisms of these trends were traced to the alteration of the matrix fracture toughness and fiber/matrix interfacial bond. Rubber particle bridging was found to contribute to crack width control. Finally, the combined use of the LC3 green binder and CR led to a lowering of the embodied and operational carbon footprint of ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Polypropylene Composites Reinforced With Recycled Waste Cellulosic Fiber/Fine Mixture: The Impact of Cellulose Sieving on Performance

This study explores how a sieving step of waste cellulosic fiber and fine (WCFF) mixture affects the performance of WCFF‐loaded polypropylene (PP) composites and whether the separation of fines from fibers offers an added benefit. The WCFF samples were downsized, and four different filler size ranges were sieved using a series of mesh sizes from 4 to 0.85 mm. The WCFF/PP composites were then compounded at 20 wt.% loading of WCFF using a twin‐screw extruder. Incorporating WCFF increased the tensile strength to 41.28 MPa and the modulus to 3207 MPa, accounting for 28% and 38% enhancements, respectively. Interestingly, the greatest improvements were associated with the nonsieved WCFF case, and the sieved WCFF fibers provided only marginal enhancements over virgin PP. The outperformance of nonsieved WCFF was attributed to the synergistic reinforcement of hybrid fibers and fines as well as the maintenance of longer fibers in the system. However, the strain at break and impact strength of PP decreased after introducing WCFF. Moreover, the complex viscosity and storage modulus increased with an increase in the filler size, due to the formation of a more effective percolative network. The PP's crystallinity exhibited a relatively strong dependency on the sieving, where WCFF samples with short‐aspect‐ratio fillers promoted the crystallinity significantly. It was also found that the WCFF degradation onset temperature increased once it was incorporated into PP. This study suggests that waste cellulosic feedstocks can be utilized as a reinforcement without additional sieving to manufacture high‐performance and cost‐effective composites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Cradle-to-gate life cycle assessment of advanced composite panels incorporating CO 2 -derived multi-walled carbon nanotubes and hemp fiber for sustainable building applications

Advanced composite panels represent a promising pathway to reducing carbon emissions in the construction industry, yet comprehensive environmental impact assessments remain limited. Here, in this study, we conduct a life cycle assessment (LCA) to evaluate the environmental impacts of innovative composite panels produced from multi-walled carbon nanotubes (MWCNTs), hemp fiber (HF), recycled carbon fiber (rCF), and recycled polypropylene (PP), exploring their potential as baseline structural equivalents to conventional gypsum board. MWCNTs and HF play a critical role in sequestering carbon during raw material production, while the recycling processes for CF and PP generally require less energy compared to virgin material production. The LCA evaluates environmental performance using the TRACI 2.1 method, covering global warming potential (GWP), ozone depletion, smog formation, acidification, eutrophication, carcinogenic and non-carcinogenic effects, respiratory impacts, ecotoxicity, and fossil fuel depletion. Compositional variations—resin type (virgin vs. recycled), rCF content (9–29 wt%), and HF content (10–30 wt%)—are introduced for sensitivity and hotspot analyses. Results demonstrate that, when compared on the basis of preliminary structural equivalence, increasing recycled PP, rCF, and HF content can significantly reduce global warming potential compared to gypsum board. Beyond carbon reduction, the composite panels show trade-offs across other environmental categories. With the growing demand for composite materials in interior panels, ceiling systems, and exterior claddings, these findings highlight the environmental benefits and potential trade-offs of the proposed composites, establishing a foundational framework to support their continued development toward full building-system integration.

Advanced composite manufacturing↗
DOE OSTI2023

Recycled Glass Polypropylene Composites from Transportation Manufacturing Waste

In recent years there has been growing interest in developing recycling technologies for composites manufacturing scrap, process waste and end-of-life parts. The focus of this work was to establish processing routes and mechanical property bounds for glass-polypropylene (PP-GF) scrap from the production of parts for truck trailers, automobiles, and rail cars. This study considered PP-GF scrap and demonstrated extrusion-compression molding (ECM) as a viable route for the closed-loop manufacture of composite parts. The results were promising in terms of the strength and modulus retention of the PP-GF recyclate. The tensile strength and modulus was the highest for 50% and 66% recycled content, compared with 100% and 83% recycle content. The flexural strength and modulus of the 100% and 83% recycled compositions was higher than the 66% and 50% recycled content, respectively. The impact energy absorption of the PP-GF recyclate at at all fiber loadings was superior in absorbing energy compared with the incumbent (benchmark) plywood. This work is useful to designers seeking to incorporate recycled materials in their products.

Vaidya, Uday↗
DOE OSTI2025

Elucidating the impact of fiber source on polypropylene/hemp composite performance for the automotive industry

Given their high strength-to-weight ratio, there is an ever-increasing volume of plastics being used in the automotive industry as plastics aid in the charge to lightweight vehicles for improved fuel efficiency. However, these plastics are often landfilled at their end-of-life, which has given rise to the demand for sustainable materials and waste management alternatives compared to purely synthetic systems. Natural fiber composites have been explored as a viable material option to reduce the environmental impact of plastic use in automobiles while simultaneously ensuring the part performance is not sacrificed. Herein, we explored the use of hemp/polypropylene (PP) composites in which US-sourced hemp is compared to internationally sourced and industrially available hemp. There appears to be a minimal impact on the composite properties regardless of fiber sourcing, and the addition of a natural filler to the PP matrix results in up to a 367% increase in Young's modulus, 126% increase in heat deflection temperature, and comparable water uptake performance. It should be noted that the natural filler addition does increase density by up to 13% due to the higher density of natural fibers compared to the low-density PP matrix. A modified rule of mixtures calculation revealed that the composite materials produced in this study demonstrated good agreement with analytical modeling. Finally, a screening analysis was performed exploring the transportation of hemp fibers, and the results build a strong case for regionalized manufacturing of automotive parts.

Hubbard, Amber M. [Oak Ridge National Laboratory (↗
DOE OSTI2025

Sizing of discontinuous natural fibers: Effect of sizing approach and sizing concentration on composite properties

Natural fiber reinforced composites (NFRCs) are gaining attention in automotive applications as an alternative to glass fiber composites due to their lightweight and renewable sourcing. However, the inherent hydrophilicity of natural fibers leads to poor compatibility with hydrophobic polymers which adversely affects the mechanical properties of the composites and can limit their application to non-structural parts. Sizing is a common approach used for synthetic fibers to improve the interface between fiber and matrix. However, there is limited study on the sizing of natural fibers, and hence the focus of this work. Here, in this study, two different approaches to sizing discontinuous coir fibers were investigated, namely; (1) ex-situ sizing and (2) in-situ sizing. A commercial polypropylene (PP) based sizing agent was used and the effects of varying sizing solution concentrations (1.5, 2.5, and 3.5 wt%) on the properties of the composites was studied. Results showed that composites prepared via the in-situ sizing process had better fiber–matrix adhesion and improved tensile properties compared to ex-situ sized composites. On studying the effect of different sizing concentrations on composite properties, we found that the tensile strength of the composites increased (by ∼ 42 %) up to 2.5 wt% sizing concentration (in solution) and then decreased. However, the impact strength decreased significantly on increasing the sizing content beyond 1.5 wt% (by ∼ 40 %). Additionally, the study was further extended to investigate the effect of sizing on different NFRCs (coir, banana, and cottonized hemp fiber) where effectiveness of sizing was found to be influenced by the fiber surface morphology.

36 MATERIALS SCIENCE↗
NASA NTRS2016

Free-Space Quantum Key Distribution with a High Generation Rate Potassium Titanyl Phosphate Waveguide Photon-Pair Source

A high generation rate photon-pair source using a dual element periodically-poled potassium titanyl phosphate (PP KTP) waveguide is described. The fully integrated photon-pair source consists of a 1064-nanometer pump diode laser, fiber-coupled to a dual element waveguide within which a pair of 1064-nanometer photons are up-converted to a single 532-nanometer photon in the first stage. In the second stage, the 532-nanometer photon is down-converted to an entangled photon-pair at 800 nanometer and 1600 nanometer which are fiber-coupled at the waveguide output. The photon-pair source features a high pair generation rate, a compact power-efficient package, and continuous wave (CW) or pulsed operation. This is a significant step towards the long term goal of developing sources for high-rate Quantum Key Distribution (QKD) to enable Earth-space secure communications. Characterization and test results are presented. Details and preliminary results of a laboratory free-space QKD experiment with the B92 protocol are also presented.

photons↗
DOE OSTI2025

Mixed polyamide and polyester upcycling via chemical autoxidation and engineered Pseudomonas putida

Polyamides, such as nylons, are often used in multi-component materials, like textiles and packaging, and are accompanied with unique recycling challenges. Recently, autoxidation and bioconversion has emerged as a tandem approach for the conversion of mixed plastics waste to single products, however the fate of polyamides in these processes is unknown. Here, we optimized the autoxidation of nylon-6 and nylon-6,6 depolymerization, achieving >92 mol% nitrogen recovery from both substrates, predominantly as acetamide, and 20–27 mol% carbon recovery (not including acetamide). Experiments with 13 C-labeled acetic acid demonstrated that the carbon in acetamide was solvent derived. Autoxidation of mixed nylon-6 and poly(ethylene terephthalate) (PET) post-consumer fibers resulted in similar carbon and nitrogen recoveries from nylon, while PET was depolymerized to terephthalic acid (TPA) at >65 C-mol% recovery. Next, we engineered Pseudomonas putida KT2440 to utilize acetamide as the sole carbon and nitrogen source for growth through the constitutive expression of genes encoding amidase enzymes, including a native amidase (PP_0613) shown to be active on C 2 –C 4 amides. Heterologous chromosomal expression of amiE, encoding the amidase from P. aeruginosa, was found to be superior to PP_0613 constitutive expression in genome integrated strains. Prior engineering to enable TPA conversion to β-ketoadipate pathway intermediate protocatechuate was leveraged and combined with deletion of pcaD to produce muconolactone as a product. Finally, a stacked strain engineered for conversion of acetamide, TPA, and DCAs was evaluated on the reaction product from autoxidation of mixed post-consumer nylon and PET fibers without any supplemental nitrogen, achieving quantitative yields in the presence of supplemental carbon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2024

3D Printed Materials Characterization for Rapid Prototyping and Plant Growth

Through KSC IRTD funding in 2022, this project brought a list of 18, 3D printed filaments into formal characterization testing to provide a reference for their behaviors under relevant applications. The project format set up a series of tests to expose 3D printed specimens. A total of 1,989 individual 3D printed test specimens were sent across KSC to be scrutinized by three laboratories to fulfill a multidisciplinary assessment of each material TRL. Testing started with 18 materials. Initially, seed germination assays in the PPA, sample materials were enclosed in petri dishes with lettuce seeds on damp germination paper. No significant impacts on lettuce seed germination were observed in this testing. Next, sample coupons were printed and sent for materials testing to the KSC Analysis/Mechanical and Environmental Testing Laboratory, where they were subjected to 14- and 30-day soak periods in solutions used to provide nutrients to plants or to sanitize hardware before and after use. Following a long soak typical of a 30-day plant growout in Hoagland’s solution, 14 materials gained more than 10% of their own mass. This indicated an increased potential for leaching or providing conditions that are not food safe. Materials that exceeded 15% absorption by mass were eliminated from further testing. Based off this result, the team continued with a core list of nine filaments to fulfill Tensile, Flexural, Biofilm formation, and plant growth testing. Those materials were PLA (Raise3D), ABS (Raise3D), PETG (PolyethyleneTerephthalate Glycol) (Raise3D), ASA (Acrylonitrile Styrene Acrylate) (Raise3D), PC (Polycarbonate) (Raise3D), TPU (Thermoplastic polyurethane)-95 (Raise3D), PLA Copper (Gizmodorks), PP (Polypropylene) (Braskem), and HIPS (High Impact Polystyrene) (Gizmodorks). Testing also quantified the spectral impact of using different color 3D printed surfaces in a growth chamber. The material used for spectral testing was PLA. Printing employed a standard surface texture representative of all materials. It was shown through Tensile Testing (ASTM D638-22) that the breaking force of a 3D printed part greatly varied depending on layer orientation. This is common through all materials, and demonstrates that the strength of a 3D printed component can be maximized by layering the material normal to the primary force on the part. Four-point flexural testing (ASTM D790) provided quantities of interest, Flexural modulus, Flexural strength, Flexural stress, and strain at break within a 5% strain limit from each of nine materials. Biofilm formation testing was conducted in the Molecular and Microbiological Laboratory. Testing completed on specimens from each material showed equal formation on the surface. Additional plant growth testing was conducted in the PPA beyond the initial germination testing. The final assessment documents that three materials (PLA, ABS, and PC) have reached TRL 6 through extensive testing, and ultimate end-to-end applied use in experimental or testing conditions (flight and ground). TRL 5 materials (ASA, TPU-95, PLA Copper, PP, PETG, and HIPS) have all been successfully applied in Research and Development for crop growth applications and are ready to be applied in formal testing. TRL 4 materials Nylon910, PLA Carbon Fiber, PPA CF, PPA Glass Fiber (GF), NinjaFlex, and P-filament 721 are materials that were able to be printed and tested, but have yet to show data meeting applied requirements. TRL 3 NylonX, Flex TPE-185, and Nylon were unable to be reliably printed to fulfill testing. These results provide researchers with reference for materials to use during plant growth experimentation, and also set a standard for future characterization work applying 3D printing and materials to testing, research, and experimentation.

Gioia Massa↗
DOE OSTI2024

Visible to near-infrared spectral reflectance along the NGEE-Arctic tram transect, Utqiagvik (Barrow), Alaska, 2015-2018

Canopy spectral reflectance collected measured in 2015-2018 along the NGEE-Arctic tram located on the Barrow Environmental Observatory (BEO), Barrow, Alaska. Measurements were made using a PP-Systems UniSpec-DC spectrometer mounted on an automatically operated instrument cart. Spectra were collected at 137 stop points at 0.5 m intervals along the tram transect. Transect runs were collected daily, or multiple times per day, from April or May through to August or September each year. Downwelling radiance was measured using a 2 meter fiber optic cable connected to a cosine diffuser. Upwelling (i.e. reflected) radiance was measured using a 2 meter cable connected to a 12 degree field-of-view (FOV) lens. Canopy reflectance was calculated using the ratio of upwelling to downwelling radiance measured over a 99.99% reflectance Spectralon standard measured at the start of each measurement set. Unprocessed spectral data are presented in .spu files. Metadata are provided in csv files, and the instrument manual (pdf). The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a 15-year research effort (2012-2027) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Understanding the Elastic, Plastic, and Damage Features in Fracturing of Self-reinforced Thermoplastic Composites via Non-destructive Digital Imaging Correlation

This work demonstrated the utilization of non-destructive Digital Imaging Correlation (DIC) method to characterize the elastic, plastic, and damage features during the Mode I intra-laminar fracturing process of self-reinforced thermoplastic composites by using a self-reinforced polypropylene (PP) composite as an example. The DIC results clearly showed the development of huge plastic zone (PZ) and non-negligible Fracture Process Zone (FPZ) in front of the notch tip during the fracturing process, and the geometries and sizes of the foregoing zones at the peak load were further quantified. Such an interesting fracturing behavior of self-reinforced thermoplastic composites is way different from brittle materials (e.g., glass, acrylic, etc.), ductile materials (e.g., aluminum, steel, etc.), and even quasi-brittle materials (e.g., concrete, nanoparticle-reinforced composites, tough ceramics, wood, cement, carbon/glass fiber-reinforced polymers, etc.). Thus, understanding the elastic, plastic, and damage features is the first step before better characterizing the material fracture properties of self-reinforced thermoplastic composites through new analytical methods and computational modeling. These efforts are of utmost importance for wide applications of self-reinforced thermoplastic composites in various engineering fields in the future.

Lightweight Composites, Self-reinforced Thermoplas↗