Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRECIPITATION HARDENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Localized corrosion at nm-scale hardening precipitates in Al-Cu-Li alloys

The localized corrosion of Li-containing nm hardening precipitates in the 3rd generation of Al-Cu-Li alloys was investigated based on a quasi in situ approach by sequentially exposing the material to NaCl solution and characterizing the structural, chemical, and electrochemical evolution at atomic scale using electron microscopy, spectroscopy, 3D tomography, electrochemical measurements, and DFT calculations. Localized corrosion of Al 7.5 Cu 4 Li (TB phase) initiated along {001} family of planes through the dealloying of Al and Li due to a low surface work function. Cu was enriched along the Cu (110) // T B (011) // Al (100) orientations on and around corroded T B precipitates. No strong galvanic interactions were observed at the T B and Al matrix interface due to the formation of a Li-C-O rich passivation layer during electrolyte exposure. Similarities and differences between T B and other common Al-Cu-Li precipitates (Al 2 CuLi, Al 6 CuLi 3 , and Al 3 Li) with respect to corrosion are discussed. Overall, the reported corrosion mechanism can assist in the assessment of the localized corrosion susceptibility of precipitation-hardened Al alloys and assist in the design of new alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electric current-induced precipitation hardening in advanced high-strength steel

Effect of electric current on precipitation hardening for advanced high-strength steel is investigated based on mechanical testing and microscopic observation. Complex-phase steel containing nano-sized Nb-bearing carbides was used. By comparing the flow stress between uniaxial tension with applied electric current (pulsed tension) and without electric current (nonpulsed tension) at various elevated temperatures, the influence of electric current on precipitation hardening was confirmed. A higher values of Vickers hardness and full-width-at-half-maximum were obtained in the pulsed tensile specimen compared to the identically heat treated specimen after the same deformation. Small angle neutron scattering analysis showed that the volume fraction and mean diameter of newly formed precipitates in the pulsed tensile specimen were higher and larger than those in the induction heat treated specimen, respectively. In conclusion, it clearly shows that additional precipitation hardening could be induced by the athermal effect of electric current, which is distinct from the thermal effect of Joule heating.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of coherent-precipitate-hardened high-entropy alloys with hierarchical NiAl/Ni 2 TiAl precipitates in CrMnFeCoNiAl x Ti y alloys

Coherent precipitates hardening is currently emerging strengthening mechanism of the various high entropy alloys (HEAs). Recently, CrMnFeCoNiAl x HEAs have been studied to show a phase transition from face-centered-cubic (FCC) to body-centered-cubic (BCC) and formation of coherent precipitates (B2-NiAl) within the BCC matrix. The coherent precipitates in the CrMnFeCoNiAl x alloys could contribute to increase the strength but lead to considerable reduction of the ductility. The present work systematically investigated a series of CrMnFeCoNiAl 0.5 Ti x alloys to further improve the strength and plasticity, as compared to the previously reported CrMnFeCoNiAl x HEAs. As a result, an increase of Ti addition leads to the phase transition from FCC to BCC and formation of lamellar structure and hierarchical precipitates reinforced by B2-NiAl and L2 1 -Ni 2 TiAl phases. Excellent mechanical properties were achieved from CrMnFeCoNiAl 0.5 Ti 0.1 and CrMnFeCoNiAl 0.5 Ti 0.2 alloys. Herein, the mechanical properties of the CrMnFeCoNiAl 0.5 Ti x alloys were discussed via theoretical strengthening mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of twin growth mechanisms in precipitate hardened AZ91

Here, in this work, an elasto-viscoplastic fast-Fourier-transform (EVP-FFT) model with a dislocation-density (DD) based hardening law is employed to study the growth of a {10$\bar{1}$2} tensile twin that is blocked by basal-precipitates in precipitate-hardened AZ91 magnesium alloy. It is frequently reported that twin growth is hindered in precipitate-hardened Mg alloys; however, thick twin domains are often observed experimentally in these material systems. Detailed numerical investigation of deformation twinning starting from an early propagation stage, before twin growth, reveals that the stress fields that result from two sequentially propagated twins co-impinging on a precipitate relaxes the twin back stress locally and promotes twin growth at the twin-precipitate junction. Based on these findings, a two-step growth mechanism is proposed for twins arrested by precipitates. In the first step, the interaction of a twin tip with a precipitate develops a stress concentration on the other side of the precipitate, prompting the formation of a second twin. Subsequently, the back stresses associated with the first twin are relaxed by the formation of the second twin, allowing the first twin to grow at the twin-precipitate junction and eventually engulf the precipitate. This mechanism suggests that twin growth can be achieved locally with minimal additional external forces, explaining how relatively large twin domains can develop even in the presence of arrays of precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A high-strength precipitation hardened cobalt-free high-entropy alloy

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. A Co-free (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 88 Ti 4 Al 8 HEA was developed and studied in this work. In contrast to previous Co-free HEAs, this alloy is close to equiatomic in its composition and promises a more pronounced high-entropy effect. Scanning electron microscopy, transmission electron microscopy, atom probe tomography, and synchrotron-based, high-energy X-ray diffraction were used to characterize this alloy and revealed a complex four-phase structure, with an FCC matrix, γ’ precipitates, and a network of B2 and χ phase particles. This structure granted 2151 MPa compressive strength and good thermal stability, but with limited ductility and slow precipitation kinetics. A strengthening analysis of the alloy shows that the B2 and χ provided the most significant strengthening contribution, adding 312 MPa and 788 MPa respectively. Furthermore the strengthening effect from the nanoscale γ' is also considerable, adding 608 MPa in total. This study lays the foundation for the continued development of high-strength Co-free HEAs with improved and satisfactory ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Precipitation hardening of laser powder bed fusion Ti-6Al-4V

Here, the laser powder bed fusion (PBF-L) additive manufacturing (AM) community has dedicated significant efforts into process optimization and control for defect-free Ti-6Al-4V. As defects become less of an issue for PBF-L Ti-6Al-4V, the processing-structure-properties (PSP) relationships between AM microstructures can now be explored to optimize mechanical properties. Lower temperature aging treatments around 550 °C in wrought Ti-6A-4V have been historically understood to precipitation harden the α phase with an ordered, hexagonal close packed (HCP) α 2 phase. The α 2 phase existed as nanoscale Ti 3 Al precipitates coherent with the parent α phase. The goal of the present investigation was to implement a vacuum heat treatment of 545 °C for 100 hours on PBF-L Ti-6Al-4V. This vacuum heat treatment took place after an initial hot isostatic pressure (HIP) treatment that decomposed the as-built, martensitic microstructure. The vacuum aging successfully produced nanoscale precipitates of α 2 phase within α-laths, confirmed via atom probe tomography (APT). Microstructural-length scale and quasi-static mechanical properties were investigated by nanoindentation and uniaxial tensile tests of miniaturized test specimens. Given the sensitivity of Ti-6Al-4V mechanical properties to small changes in chemistry, all test specimens originated from the same build. The α 2 precipitation resulted in significantly harder α-laths (≈ 2 GPa) as measured via nanoindentation, as well as a relative yield and ultimate tensile strength increase of 60 MPa and 38 MPa, respectively. Analysis of Variance (ANOVA) of the datasets revealed no statistical differences in total elongation between the HIPed and HIPed + aged specimens, indicative of the aging treatment producing a net benefit of strength with no loss in ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dislocation cross-slip in precipitation hardened Mg–Nd alloys

An integrated experimental characterization and molecular dynamics (MD) simulation approach was used to explore the dislocation-precipitate interactions in a dilute Magnesium–Neodymium (Mg–Nd) precipitation hardened alloy. In situ indentation in a transmission electron microscope (TEM) and postmortem TEM characterization of deformed samples and MD simulations revealed that basal < a > type dislocations interacted differently with β 1 (Mg 3 Nd) and β"(Mg 3-7 Nd) precipitates. For β" precipitates, the basal dislocations directly shear the precipitates. For β 1 precipitates, such shearing becomes much more difficult because it requires the creation of antiphase boundaries in the ordered lattice of β 1 precipitates. Screw dislocations were observed to cross-slip from basal to the prismatic plane, which could be parallel to the broad facet of β 1 precipitates. It is postulated that double cross-slip (basal to prismatic to basal) via the Hirsch mechanism may enable screw dislocations to overcome the β 1 precipitates. MD simulations also revealed that an edge dislocation is unable to bypass the precipitate via the generation of screw dislocation segments plus the double cross-slip mechanism. The edge dislocation can bow around the precipitate, and the segment that adopts a screw character can cross-slip to the prismatic plane but with increasing applied stress, cross-slips back to the original basal plane to continue glide via precipitate shearing. Finally, the implication of glide dislocation - β 1 -precipitate interaction mechanisms on the strength and ductility of β 1 precipitate dominant microstructures is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural evolution in a precipitate-hardened (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 multi-principal element alloy during high-pressure torsion

Multi-principal element alloys demonstrate high strength, thermal stability, and irradiation resistance, making them excellent candidate materials for applications in nuclear reactors and other harsh environments. Some studies have examined the use of high-pressure torsion to strengthen MPEAs through grain size reduction and strain hardening. However, no studies have investigated the effect of HPT on secondary phases (precipitates) within an MPEA. Two alloys, (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 containing Ni(Ti, Al) B2 phase, and CrFe σ phase, and single-phase Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , were fabricated by casting and heat treatment. Both alloys were then processed with HPT to study microstructural evolution. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the alloys before and after HPT processing. HPT processing produced a nanocrystalline structure in both alloys, but (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 exhibited a significantly smaller grain size and higher dislocation density than Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , with corresponding higher hardness. Before HPT, the (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 alloy consisted of large grain (~ 400 μm) and precipitates, including B2 of ~ 38 μm average size, B2 of ~ 0.7 μm average size, and small amounts of σ of ~ 1.5 μm average size. After HPT, the larger B2 precipitates were decreased in size and volume fraction, while the smaller B2 precipitates were completely dissolved; the σ precipitates appeared unaffected by HPT, likely due to their much higher hardness. Finally, observation of the B2 precipitate distribution along radial distance indicates that the strain caused the precipitates to fracture at intermediate strain (γ = 125) and dissolve at high strain (γ = 280).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic Shear Deformation of a Precipitation Hardened Al 0.7 CoCrFeNi Eutectic High-Entropy Alloy Using Hat-Shaped Specimen Geometry

Lamellar eutectic structure in Al 0.7 CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc + B2 microstructure with high flow stresses > 1300 MPa under quasi-static tensile deformation and >10% ductility. The response to shear loading was not investigated so far. This is the first report on the shear deformation of a eutectic structured HEA and effect of precipitation on shear deformation. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local dynamic shear response of the alloy. The change in the width of shear bands with respect to precipitation and deformation rates was studied. The precipitation of L1 2 phase did not delay the formation of adiabatic shear bands (ASB) or affect the ASB width significantly, however, the deformed region around ASB, consisting of high density of twins in fcc phase, was reduced from 80 μm to 20 μm in the stronger precipitation strengthened condition. We observe dynamic recrystallization of grains within ASBs and local mechanical response of individual eutectic lamellae before and after shear deformation and within the shear bands was examined using nano-indentation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Precipitation Hardening in Ferroelectric Ceramics

Domain wall motion in ferroics, similar to dislocation motion in metals, can be tuned by well-concepted microstructural elements. In demanding high-power applications of piezoelectric materials, the domain wall motion is considered as a lossy hysteretic mechanism that should be restricted. Current applications for so-called hard piezoelectrics are abundant and hinge on the use of an acceptor-doping scheme. However, this mechanism features severe limitations due to enhanced mobility of oxygen vacancies at moderate temperatures. By analogy with metal technology, the authors present here a new solution for electroceramics, where precipitates are utilized to pin domain walls and improve piezoelectric properties. Through a sequence of sintering, nucleation, and precipitate growth, intragranular precipitates leading to a fine domain structure are developed as shown by transmission electron microscopy, piezoresponse force microscopy, and phase-field simulation. This structure impedes the domain wall motion as elucidated by electromechanical characterization. As a result, the mechanical quality factor is increased by ≈50% and the hysteresis in electrostrain is suppressed considerably. This is even achieved with slightly increased piezoelectric coefficient and electromechanical coupling factor. This novel process can be smoothly implemented in industrial production processes and is accessible to simple laboratory experimentation for microstructure optimization and implementation in various ferroelectric systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Study on the continuous phase evolution and physical properties of gas-atomized high-entropy alloy powders

In this study, AlCoCrFeNi high entropy alloy (HEA) powders were fabricated by gas atomization process, and the effects of annealing heat treatment on phase evolution and mechanical properties were investigated. The as-atomized powders have pure BCC phase with a spherical shape and equal composition distribution, and then the FCC and sigma phase sequentially generated after annealing. The mechanical property such as hardness was evidently enhanced, which was caused by precipitation hardening effect. After the raw powders were annealed at 600 °C, the FCC (Al–Ni) phase began to precipitate, the its phase intensity raised with the annealing temperature. Then, the sigma phase (Fe– Cr)formed as the annealing temperature reached 800 °C. Both mechanical properties and lattice constant were influenced by heating effect. According to the results, the lattice became loose with the increasing temperature. In summary, the mechanical properties and phase constitutions of gasatomized AlCoCrFeNi HEA powders can be adjusted via annealing process, resulting in precipitation hardening effect.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Intergranular ductile failure of materials with plastically heterogeneous grains

In several precipitation hardened alloys that are susceptible to intergranular ductile failure, precipitation does not always occur uniformly throughout the microstructure, and regions close to grain boundaries may remain precipitate-free. These precipitate-free zones (PFZs) in the material microstructures result in plastically heterogeneous grains, since PFZs are expected to have lower yield strength but higher strain-hardenability compared to the precipitate containing grain interior. Experimentally, the presence of PFZs in precipitation-hardened alloys has been associated with both increase and decrease in materials’ ductility, with or without significant change in the strength. Thus, to understand and rationalize the experimental observations, we have carried out extensive microstructure-based finite element calculations of intergranular ductile failure in materials under tensile loading conditions. In the calculations, both the grain boundaries and PFZs are discretely modeled, and a wide range of the values of yield strength, strain-hardenability and width of PFZs in the material microstructures are analyzed. Our results show that the effects of PFZs on the overall mechanical response of the material strongly depend on the values of yield strength and strain-hardenability of PFZs. Here, there exists an optimum combination of the values of these two parameters that can result in the overall ductility and tensile strength of the material microstructures with PFZs being greater than the microstructures without PFZs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Precipitation-site competition in duplex stainless steels: Cu clusters vs spinodal decomposition interfaces as nucleation sites during thermal aging

Competing microstructural evolution mechanisms can exist simultaneously when duplex stainless steels are operating for several decades in a high temperature service environment. Such competition between different microstructural evolution pathways can be difficult to ascertain using simple model alloy systems necessitating detailed structural and compositional analysis of phase transformation mechanisms in complex alloys Thus, in this study duplex stainless steels with complex but well understood chemistries were used to investigate the relative importance of different heterogeneous nucleation sites – specifically spinodal decomposition and Cu clustering – on precipitation of Ni-Si-Mn particles during long term thermal aging. Precipitation of Ni-Si-Mn particles in duplex stainless steels and ferritic steels during thermal aging and irradiation is known to have profound effect on mechanical properties. Using duplex stainless steels with custom modified compositions along with atom probe tomography characterization and first-passage kinetic Monte Carlo (FPKMC) simulations it is revealed that while the interface between Cr and Fe formed during spinodal decomposition can be a pathway for diffusion of Ni, Si, Mn, and Cu, it is not a site that encourages precipitation of Ni-Si-Mn rich particles. Instead, the presence of a higher concentration of Cu in these steels leads to formation of small Cu clusters with high energy interfaces that act as nucleation sites for Ni-Si-Mn particles because of its strong interaction particularly with Ni increasing the chemical driving force for precipitation. These results will help inform predictive models for the use of duplex stainless steels and other precipitation-hardened alloys for extended operation at high temperatures.

Duplex stainless steel, Thermal aging, Precipitati↗
DOE OSTI2022

Strengthening of nanocrystalline Al using grain boundary solute additions: Effects of thermal annealing and ion irradiation

Strengthening of nanocrystalline Al by grain boundary solute additions was investigated for a series of dilute aluminum alloys, Al-Sc, Al-Sb, Al-Cr, and Al-W with grain sizes in the range of 50–200 nm. Thermal annealing of the alloys at low temperatures led to alloy softening, but with negligible change in the grain size. The re- duction in strength can be attributed to the loss of solute in the grain boundaries arising from grain boundary diffusion and precipitation. Annealing at higher temperatures led to grain growth, but with little additional loss of strength, a result of precipitation hardening. The Al-Sc and Al-Sb alloys were additionally subjected to ion irradiation at various temperatures. Furthermore, these studies revealed that annealed samples regained their hardness due to solute redistribution by ion beam mixing. Alloy strength was independent of grain size between 50 and 150 nms. Irradiation-induced segregation of Sb to grain boundaries in Al-Sb further enhanced strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Radiation‐Resistant Aluminum Alloy for Space Missions in the Extreme Environment of the Solar System

Future human exploration of the solar system demands advanced materials capable of withstanding extreme environments, particularly exposure to solar energetic particle radiation. Current material selection criteria for space applications prioritize a high strength-to-weight ratio, high corrosion resistance and manufacturability, favoring age-hardenable Al-based alloys. However, conventional precipitation-hardened Al alloys suffer from irradiation-assisted dissolution of strengthening phases at doses as low as 0.2 displacements-per-atom (dpa), undermining their performance. Furthermore, these alloys develop radiation-induced defects, such as dislocation loops and voids, even at low doses. This study presents a novel ultrafine-grained (UFG) Al-based alloy, designed using the crossover alloying concept and strengthened by T-phase precipitates, featuring a chemically-complex structure with 162 atoms in its unit cell composed of Mg 32 (Zn,Al) 49 . It is showed that T-phase precipitates have exceptional radiation tolerance up to 24 dpa. Owing to the nanoscale UFG structure, dislocation loops are suppressed, and voids are only observed beyond 75 dpa. Microtensile tests up to 20 dpa confirm the preservation of mechanical performance under irradiation. The results underline the potential of this alloy as a radiation-resistant, lightweight material for future space applications. Three key strategies enable this performance: (i) stabilization of a UFG microstructure, (ii) T-phase precipitation featuring a highly negative Gibbs free energy and chemically-complex giant unit cell, and (iii) precise process control to prevent grain growth during heat treatment and irradiation.

36 MATERIALS SCIENCE↗