Search NASA⌕ Search

SEARCH · Search NASA

Results for “PVDF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Understanding the Solution Dynamics and Binding of a PVDF Binder with Silicon, Graphite, and NMC Materials and the Influence on Cycling Performance

The impact of the binding, solution structure, and solution dynamics of poly(vinylidene fluoride) (PVDF) with silicon on its performance as compared to traditional graphite and Li 1.05 Ni 0.33 Mn 0.33 Co 0.33 O 2 (NMC) electrode materials was explored. Through refractive index (RI) measurements, the concentration of the binder adsorbed on the surface of electrode materials during electrode processing was determined to be less than half of the potentially available material resulting in excessive free binder in solution. Using ultrasmall-angle neutron scattering (USANS) and small-angle neutron scattering (SANS), it was found that PVDF forms a conformal coating over the entirety of the silicon particle. This is in direct contrast to graphite–PVDF and NMC–PVDF slurries, where PVDF only covers part of the graphite surface, and the PVDF chains make a network-like graphite–PVDF structure. Conversely, a thick layer of PVDF covers NMC particles, but the coating is porous, allowing for ion and electronic transport. The homogeneous coating of silicon breaks up percolation pathways, resulting in poor cycling performance of silicon materials as widely reported. These results indicate that the Si–PVDF interactions could be modified from a binder to a dispersant.

25 ENERGY STORAGE↗
DOE OSTI2023

Boosting Piezoelectricity by 3D Printing PVDF‐MoS 2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor

Abstract Additively manufactured flexible and high‐performance piezoelectric devices are highly desirable for sensing and energy harvesting of 3D conformal structures. Herein, the study reports a significantly enhanced piezoelectricity in polyvinylidene fluoride (PVDF) achieved through the in situ dipole alignment of PVDF within PVDF‐2D molybdenum disulfide (2D MoS 2 ) composite by 3D printing. The shear stress‐induced dipole poling of PVDF and 2D MoS 2 alignment are harnessed during 3D printing to boost piezoelectricity without requiring a post‐poling process. The results show a remarkable, more than the eight‐fold increment in the piezoelectric coefficient ( d 33 ) for 3D printed PVDF‐8wt.% MoS 2 composite over cast neat PVDF. The underlying mechanism of piezoelectric property enhancement is attributed to the increased volume fraction of β phase in PVDF, filler fraction, heterogeneous strain distribution around PVDF‐MoS 2 interfaces, and strain transfer to the nanofillers as confirmed by microstructural analysis and finite element simulation. These results provide a promising route to design and fabricate high‐performance 3D piezoelectric devices via 3D printing for next‐generation sensors and mechanical–electronic conformal devices.

2D MoS2↗
DOE OSTI2024

Tailoring Piezoelectricity of 3D Printing PVDF-MoS 2 Nanocomposite via In Situ Induced Shear Stress

3D printing of unique structures with tunable properties offers significant advantages in the fabrication of complex and customized electronic devices. Here, this study introduces a process-microstructure–property-guided manufacturing route to fabricate PVDF-2D MoS 2 piezoelectric nanocomposites with tunable piezoelectric properties without having a postprocess. We control PVDF’s microstructure through direct ink writing (DIW) 3D printing while tuning PVDF-MoS 2 interfacial strain by controlling rheology and 3D printing parameters, such as nozzle size and printing speed. Our approach demonstrates tunable piezoelectricity in PVDF-MoS 2 , achieving a 15-fold increase in the piezoelectric coefficient (d 33 ) at a printing-induced shear stress of 6685 Pa. This enhancement arises from the electrostatic interactions between PVDF and MoS 2 and the filler distribution and alignment caused by the in situ shear stress in 3D printing, as confirmed by XPS and Raman mapping analyses. Our findings advance the understanding of piezoelectric mechanisms in PVDF-based nanocomposites, laying the foundation for 3D printing of piezoelectric sensors in wearable device applications with enhanced performance and customization capabilities.

2D MoS2↗
DOE OSTI2022

A study of degradation mechanisms in PVDF-based photovoltaic backsheets

Abstract Commercial backsheets based on polyvinylidene fluoride (PVDF) can experience premature field failures in the form of outer layer cracking. This work seeks to provide a better understanding of the changes in material properties that lead to crack formation and find appropriate accelerated tests to replicate them. The PVDF-based backsheet outer layer can have a different structure and composition, and is often blended with a poly(methyl methacrylate) (PMMA) polymer. We observed depletion of PMMA upon aging with sequential (MAST) and combined (C-AST) accelerated stress testing. In field-aged samples from Arizona and India, where PVDF crystallizes in its predominant α-phase, the degree of crystallinity greatly increased. MAST and C-AST protocols were, to some extent, able to replicate the increase in crystallinity seen in PVDF after ~ 7 years in the field, but no single-stress test condition (UV, damp heat, thermal cycling) resulted in significant changes in the material properties. The MAST regimen used here was too extreme to produce realistic degradation, but the test was useful in discovering weaknesses of the particular PVDF-based outer layer structure studied. No excessive β-phase formation was observed after aging with any test condition; however, the presence of β-phase was identified locally by Fourier transform infrared spectroscopy (FTIR). We conclude that both MAST and C-AST are relevant tests for screening outdoor failure mechanisms in PVDF backsheets, as they were successful in producing material degradation that led to cracking.

14 SOLAR ENERGY↗
DOE OSTI2024

PVDF-based backsheet cracking: Mapping in situ phase evolution by X-ray scattering

One of the most common polymers used in commercial photovoltaic backsheets is polyvinylidene fluoride (PVDF). However, recent reports have shown the potential for PVDF-based backsheets to crack and fail prematurely. Previous work has suggested that polymer phase changes play a role in the failure mechanism. Here, in situ wide-angle X-ray scattering maps are used to show that α- to β-phase transformations occur at crack tips in aged PVDF-based backsheets under stretching. Substantial β-phase formation is shown to be associated with strain hardening. In addition, our work demonstrates that β-phase formation is not required for crack growth and only occurs at crack tips when plastic deformation of the PVDF polymer has occurred. In conclusion, the anisotropy in the strength of aged PVDF-based backsheets is linked to the lack of β-phase formation when strain is applied to aged backsheets in the transverse direction.

14 SOLAR ENERGY↗
DOE OSTI2025

Self-Sensing Composites via an Embedded 3D-Printed PVDF-MoS 2 Nanosensor for Structural Health Monitoring

Carbon fiber (CF)-reinforced epoxy composites are widely used in vehicle applications, where early damage detection is crucial for reliability and safety. To address this need, we developed a self-sensing epoxy/CF composite by embedding a PVDF-MoS 2 nanosensor via an embedded 3D printing method. By harnessing the intrinsic curing kinetics of epoxy, we tailored its rheological properties to optimize the embedded printing process, enabling precise and reliable support for sensor filaments without compromising the composite’s structural and functional integrity. Through comprehensive rheological and kinetic analysis, we established a quantitative relationship among curing temperature, conversion rate, and resulting yield modulus─defining a narrow processing window essential for successful sensor integration. Specifically, we identified that an epoxy yield modulus range of 180–294 Pa and a conversion rate below 10% are critical to support the PVDF-MoS 2 filament architecture. Here, this embedded 3D printing method produces complex and multimaterial PVDF-MoS 2 sensors within an epoxy matrix with minimal deformation and reduced postprocessing, which is scalable and adaptable for industrial applications. Under cyclic loading, the embedded sensors exhibited stable signals under constant loads and increased voltage signals in response to crack formation (17–35% higher) and catastrophic failure (1 order of magnitude higher), effectively capturing structural changes in real time. This study demonstrates the potential of PVDF-MoS 2 nanocomposite sensor materials for real-time structural health monitoring in epoxy–CF composite systems, enabling early detection of defects and stress anomalies, significantly reducing the risk of unexpected failures, and enhancing structural reliability.

PVDF-MoS2 sensor↗
DOE OSTI2023

Toward improved PVDF-BaTiO 3 composite dielectrics: mechanical activation of the filler versus filler content

Abstract Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength andD-Emeasurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polarβandγcrystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.

Physics↗
DOE OSTI2022

Microstructure changes during failure of PVDF-based photovoltaic backsheets

The backsheet layer of a solar module provides a safety and environmental barrier to the high voltages running through the photovoltaic (PV) cells and electrical contacts within the core of the module. However, in the past decade, backsheet cracking has become one of the most observed failure modes in PV module field surveys. In this work, the degradation of polyvinylidene fluoride (PVDF)-based backsheets is explored. Backsheet samples are either exposed to accelerated laboratory aging (UV light, heat, and moisture) or collected from the field. Fourier transform infrared and Raman spectroscopy, fragmentation testing, atomic force and scanning electron microscopy, and small-angle neutron scattering are combined to develop an understanding of how chemistry and microstructure evolve during aging. Chemical degradation, surface pitting, polymer phase changes, and anisotropic polymer domains are all observed in aged backsheet samples. The results provide insight into the degradation mechanisms that lead to cracking and field failure of PVDF-based backsheets. The comparison of aged PVDF-based backsheets helps to lay the groundwork for limiting polymer-based failure modes in PV modules.

PVDF↗
DOE OSTI2022

Preactivated zeolite nanosheet plate-tiled membrane on porous PVDF film: Synthesis and study of proton-selective ion conduction

Preactivated MFI zeolite nanosheet plates (ZNPs) with large areas (~2.0 × 2.0 μm 2 ) and nanometer thicknesses (~60 nm) were prepared directly in liquid-dispersed state. The individual ZNP was a stack of 4-nm-thick single crystalline zeolite nanosheets (ZNs) interlinked by Si–O–Si bonds between neighboring ZN surfaces. The dispersed open-pore ZNPs allowed formulating suspensions for tiling ZNP membranes on polymer substrates without requiring post-coating activation. A pinhole-free ZNP-tiled (ZNPT) membrane has been achieved on macroporous PVDF film by a self-repairing vacuum-assisted filtration coating method. The resultant ZNPT layer was ~500 nm-thick consisting of about 7 ZNP layers with inter-ZNP width and inter-ZNP entrance porosity around 9 nm and 2%, respectively. The ZNPT-PVDF membrane exhibited high selectivity to proton transport over vanadyl ion and low resistances to proton conduction in aqueous solutions. The membrane also demonstrated to function as an efficient ion separator for the vanadium redox flow battery. The reported synthesis of preactivated ZNP suspension may overcome the major hurdle to realizing polymer-supported ZN membranes, which is the inefficiency of existing methods in obtaining readily dispersible open-pore ZNs. Finally, the ZNPT-PVDF membrane can be a more affordable and sustainable alternative to the Nafion-based ion separation membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Decomposition of PVDF to delaminate cathode materials from end-of-life lithium-ion battery cathodes

The growing demand of electric vehicles and rapid consumption of rechargeable lithium-ion batteries (LIBs) require recycling of spent cathode active materials (CAMs) to reduce hazardous wastes and supply raw materials to LIB production. To separate CAMs from the cathode, direct calcination of polyvinylidene fluoride (PVDF) binder is widely applied, which leads to high energy consumption and release of toxic hydrogen fluoride. It is desirable to have an environmentally friendly and effective alternative to traditional direct calcination. In this study, five lithium salts, LiOAc (lithium acetate), LiNO 3 , LiCl, Li 2 CO 3 , and Li 2 SO 4 , were deployed and compared for their performance in recycling CAMs. A peel-off efficiency of up to 98.5% was achieved at a LiOAc to LiNO 3 molar ratio of 3:2, salt to cathode mass ratio of 10:1, and temperature of 300 °C at a holding time of 30 min. This system avoids corrosive chemicals and minimizes particle agglomeration of recycled products. Compared with sodium salt systems (NaOAc-NaNO 3 ) or direct calcination, the LiOAc-LiNO 3 system prevented high reaction temperature or further lithium loss and minimized crystal structure and morphological changes. In conclusion, a decomposition mechanism of PVDF through adsorption of HF and fluorine substitution was proposed.

25 ENERGY STORAGE↗
DOE OSTI2025

Advanced Microstructured BaTiO 3 -Embedded PVDF–HFP/PEO Film for Enhanced Triboelectric Interface in Self-Sufficient Energy Generation and Sensing

The global reliance on fossil fuels and natural gas has largely dominated the energy production field, but due to finite resource depletion and escalating greenhouse gas emissions, the immediate exploration of sustainable energy alternatives to mitigate climate change and ensure resource security has been a major concern. There has been extensive research into other more renewable methods of energy production, such as wind and hydropower. Of these current energy generation types, there are many areas of untapped potential from the mechanical movements generated ambiently not only in the large scale of power generation but also on a smaller scale. The piezoelectric and triboelectric effects are phenomena where these ambient mechanical movements can generate electrical energy. Developing a hybrid system that leverages both mechanical stress and surface charges presents an ideal opportunity to exploit these untapped energy sources. Producing a hybrid PVDF–HFP/PEO film with perovskite BaTiO 3 (BTO) enables ambient power harvesting from both mechanical movement and surface charge. The optimized cell produced a potential of up to 15 V and a current of 200 nA with a 68 kΩ resistor, a substantial increase from a base system with an average of 2.1 V and 40 nA. These hybrid TENGs offer significant potential for energy harvesting in small-scale applications, such as health monitoring devices and indicators in electric circuits.

Ybarra, Rigobert [University of Texas Rio Grande V↗
DOE OSTI2024

A High-Ceramic-Loading LATP–PVDF–Al 2 O 3 Composite Film for Lithium-Ion Batteries With Favorable Porous Microstructure and Enhanced Thermal Stability

A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Hierarchal structures tuned electrocaloric and electromechanical performance in PVDF-based tetrapolymers

Ferroelectrics with multifunctionalities are gaining increased interest in self-actuated electrocaloric effect (ECE) refrigerators. However, achieving high ECE and electromechanical (EM) coupling concomitantly for maximum heat transfer remains challenging. Here we present the structure-property relationship for poly(vinylidene fluoride-co-trifluoroethylene-co-chlorofluoroethylene-co-double bond), P(VDF-TrFE-CFE-DB), tetrapolymer, which exhibited a high ECE entropy change of 66.5 J Kg −1 K −1 and EM strain of −6.1%. We show that thermal treatment can be a key factor influencing multifunctional properties. High-temperature annealing incorporates DB and CFE units into crystalline grains to form extended-chain crystals, enabling CFE units to induce relaxor behavior and DB units to induce large structural changes at low electric fields. This synergy leads to an enhancement in both ECE and EM performances. Furthermore, at an optimized temperature of 50 °C, the annealed films exhibit giant cross-energy coupling, achieving ECE and EM performances of 100.8 J Kg −1 K −1 and −7.6%. This study provides insights into developing new ferroelectric polymers with electroactive multifunctionalities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrospinning of PVdF-HFP: novel composite polymer electrolytes (CPES) with enhanced ionic conductivities for lithium-sulfur batteries

The invention relates to lithium ion batteries and, more particularly, to lithium ion conducting composite polymer electrolyte separators. The separators include a nanofiber mat composed of electrospun nanofibers. The nanofibers include a polymer having one or more polar halogen groups, a lithium-containing solid or liquid electrolyte and nanoparticle filler. The polymer, electrolyte and filler are combined to form a solution that is subjected to the electro-spinning process to produce electrospun nanofibers in the form of the mat.

Kumta, Prashant N.↗
DOE OSTI2023

Rheo-electric measurements of carbon black suspensions containing polyvinylidene difluoride in N -methyl-2-pyrrolidone

Lithium-ion battery cathode slurries have a microstructure that depends sensitively on how they are processed due to carbon black's (CB) evolving structure when subjected coating flows. While polyvinylidene difluoride (PVDF), one of the main components of the cathode slurry, plays an important role in modifying the structure and rheology of CB, a quantitative understanding is lacking. In this work, we explore the role of PVDF in determining the structural evolution of Super C65 CB in N-methyl-2-pyrrolidinone (NMP) with rheo-electric measurements. We find that PVDF enhances the viscosity of NMP resulting in a more extensive structural erosion of CB agglomerates with increasing polymer concentration and molecular weight. We also show that the relative viscosity of all suspensions can be collapsed by the fluid Mason number (Mnf), which compares the hydrodynamic forces imposed by the medium to cohesive forces holding CB agglomerates together. Using simultaneous rheo-electric measurements, we find at high Mnf, the dielectric strength (Δε) scales with Mnf, and the power-law scaling can be quantitatively predicted by considering the self-similar break up of CB agglomerates. The collapse of the relative viscosity and scaling of Δε both suggest that PVDF increases the hydrodynamic force of the suspending medium without directly changing the CB agglomerate structure. These findings are valuable for optimizing the rheology of lithium ion battery cathode slurries. We also anticipate that these findings can be extended to understand the microstructure of similar systems under flow.

Mechanics↗
DOE OSTI2025

Surface engineering of polymeric membranes with metal oxides for improved fouling resistance and superior oil-water separation

Rapid industrial growth has increased the need for efficient membranes to separate oil-water emulsions. Polyvinylidene fluoride (PVDF) membranes, although widely used due to their chemical inertness and favorable mechanical properties, suffer from fouling due to their intrinsic hydrophobicity. Modifying these membranes after fabrication offers a practical solution as it easily fits into existing large-scale manufacturing processes. Atomic layer deposition (ALD), an atomically-precise vapor phase surface modification technique, can create ultrathin metal oxide layers that greatly improve membrane hydrophilicity without significantly affecting the original pore size. However, PVDF's lack of reactive chemical moieties makes ALD challenging. Here, in this study, we present a simple alkali treatment that greatly enhances ALD nucleation and growth on PVDF membranes. This treatment imparts exceptional oil-water emulsion separation capabilities and antifouling behavior in PVDF membranes after just a few ALD cycles, surpassing the performance of PVDF membranes coated with hundreds of ALD cycles. This dramatic reduction in the number of ALD cycles required could enable cost-effective modification of commercial PVDF membranes at scale using spatial, roll-to-roll ALD. These modified membranes outperform reported modified PVDF membranes, with >99 % permeance recovery and <1 % irreversible loss of permeance and >98 % oil rejection from oil-water emulsions over 100 h continuous operation, making them promising for advanced water purification technologies.

Atomic layer deposition↗