Search NASA⌕ Search

SEARCH · Search NASA

Results for “Paraffin wax”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Development of Thermal Scattering Law and Cross Sections of Hydrogen in Paraffin Wax

Paraffin wax is frequently used as a neutron moderator and shielding material. The main component of paraffin wax is straight-chain alkanes (n-alkanes). The deposition of paraffin wax is primarily attributed to the crystallization of n-alkanes. It is important to gain a deeper understanding of the mechanisms underlying the behavior of paraffin wax, which would impact the thermal scattering Law (TSL) and cross sections and affect the analysis of neutronic and critical systems. In this work, a classical molecular dynamics (CMD) simulation model was used in LAMMPS to create the TSL and cross sections at room temperature and pressure. To generate the required velocity autocorrelation functions (VACF), previously published data were used to validate the approach and models by comparing them with key model parameters. The phonon density of state (DOS) was calculated using Fourier transformation of the normalized VACF. This DOS was used as the primary input to estimate the TSL (S($a$, $β$)) and cross sections of hydrogen in paraffin wax. The TSL and cross sections of hydrogen were estimated using the Full Law Analysis Scattering System Hub (FLASSH) code. The cross section of hydrogen in paraffin wax is consistent with other hydrocarbon materials such as polyethylene with deviations due to structure in the lowest energy region.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Thermal Scattering Law Data Development for Paraffin Wax

Paraffin wax is often used as a nuclear moderator to slow down the fast neutrons in experimental critical assemblies [1]. It is a colorless and soft solid material that consists primarily of straight-chain alkanes (n-alkanes), which are hydrocarbons with the general formula CnH2n+2 [2-3]. The length of the hydrocarbon chain ranges from C20 to C30 and higher [2]. It is distinguished by its solid state at room temperature and begins to melt above approximately 310 K [4]. Paraffin wax is a commonly employed substance in the manufacture of shielding. One of its noteworthy characteristics is its ability to effectively absorb the neutrons. Also, it possesses a high macroscopic cross section, which enables it to efficiently moderate neutrons. As a result, paraffin wax is extensively utilized in various applications where moderation and shielding of neutrons are needed. For simulations, it is necessary to evaluate its thermal scattering law (TSL) and cross sections. Computationally, classical molecular dynamics (CMD) simulations provide the capability of simulating atomic details. For example, several unary, binary, and few multi component mixtures have been investigated of the paraffin model by using molecular dynamics simulations [5-12]. An assessment of thermal neutron scattering in a heavy paraffinic oil treated both as a solid and a viscous fluid containing 25% linear branched paraffin (C30H62), 35% one ring cycloalkane (C30H60), 15% two rings cycloalkane (C30H58), and 25% aromatic (C30H60) chains has been studied using CMD simulations for producing TSL data [13]. Nevertheless, there is lack of TSL and cross section data for paraffin wax as most of the reported analyses focus on the unary and binary mixture of n-alkanes, which is not consistent with actual paraffin wax [2]. In this work, we applied the equilibrium CMD simulations technique to explore the structure and dynamical properties of wax, which are fundamental input to calculate the TSL. A paraffin wax system was modeled using the CMD code LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator) [14-15] with the semi-empirical COMPASS [16] force field. The density of state (DOS) was calculated from the normalized velocity autocorrelation function (VACF), which is the Fourier transform of the normalized VACF. The DOS was used for the calculation of the TSL and thermal scattering cross sections. The paraffin wax atomic system was constructed by using the MedeA material design platform [17], and was benchmarked using available properties (i.e., density, bond lengths, angles, diffusivity, and viscosity).

Nuclear Criticality Safety Program (NCSP)↗
DOE OSTI2025

Large-Scale Compatibilization of Postconsumer Polyolefins in the Presence of Paraffin Wax as a Rheology Modifier

Postconsumer polyolefins (r-POs) are leading plastic waste contributors today. This study reports, for the first time, the compatibilization of r-POs at a 50 kilogram (kg) scale with a styrene block copolymer compatibilizer in the presence of paraffin waxes as rheology modifiers (RMs). The addition of the rheological modifier (RM) and compatibilizer enhances the melt flow indices (MFIs) and mechanical properties, respectively. One aspect of this study is to compare the effectiveness of low-cost paraffin wax to that of specialized and expensive RMs in r-POs. The mechanical and rheological properties such as the melt flow index (MFI) of r-POs were compared in the presence of two types of RMs. Next, the study explores the challenges encountered when scaling the compatibilization of r-POs in the presence of paraffin wax from a 10-g to a 50-kg scale. The mechanical properties were determined and compared for samples at different scales. The study further investigated the effect of the method used for blending paraffin wax with r-PO and its impact on the value of their MFI and mechanical properties. This at-scale validation could pave the way for the commercialization of r-POs.

crystallinity↗
DOE OSTI2025

Protecting air/moisture-sensitive samples using perdeuterated paraffin wax for solid-state NMR experiments under magic-angle spinning

Solid-state nuclear magnetic resonance (SSNMR) spectroscopy is a powerful technique for materials characterization, yet its application to air- and moisture-sensitive materials is often hindered by the difficulty in maintaining an inert environment during magic-angle spinning (MAS). This is particularly true for fast-MAS rotors that do not generally provide tight seals. Herein, we present a generalizable approach employing perdeuterated paraffin waxes—n-icosane-d42 and c-dodecane-d24—as protective embedding media to analyze sensitive organometallic catalysts using SSNMR. We demonstrate that these waxes significantly slow oxidative degradation under MAS conditions. Weak background 1 H and 13 C NMR signals from the waxes are effectively suppressed using double-quantum filtration and cross-polarization techniques. In conclusion, these findings offer a robust method for expanding the scope of SSNMR to air-sensitive systems, with implications for the structural study of reactive materials and catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Assessment of Training Performance, Degradation and Robustness of Paraffin-Wax Impregnated Nb 3 Sn Demonstrator Under High Magnetic Field

In the context of high-energy physics, the use of Nb 3 Sn superconducting magnets as a cost-effective and reliable technology depends on improvements in the following areas: long development and manufacturing cycles, conductor degradation after thermal cycling, long training, as well as a demonstration in accelerator magnets with a beam aperture of the full potential of modern Nb 3 Sn conductors. In short, performance, robustness, and cost are the three issues to be addressed. The Magnet Development project (MagDev) of the Swiss Accelerator Research and Technology initiative (CHART) at the Paul Scherrer Institute (PSI) aims to contribute to the solutions to each of these issues, re-thinking the manufacturing and design process. Here in our program, every innovation is to be validated by means of a panoply of fast-turnaround tools: from non-powered and powered samples and coils, tested under background field, to low-field subscale magnets and high field short prototypes. This work presents one element in this panoply of R&D vehicles: a stress-managed Nb 3 Sn coil called BigBOX, impregnated with paraffin wax, and tested, through a collaboration with the Magnet Development Program of the United States (US-MDP), in the background field of Brookhaven National Laboratory (BNL)’s common coils dipole DCC17.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

A simple and practical wax-encapsulation method for air-sensitive XAS samples

To facilitate X-ray absorption spectroscopy (XAS) measurements of air-sensitive samples, we present a simple method in which materials are encased in common paraffin wax to protect them from air and moisture. We demonstrate the efficacy of this approach using a highly reducing, air- and moisture-sensitive uranium(III) complex, the tris(amide) U[N(SiMe 3 ) 2 ] 3 (1). When finely dispersed in a boron nitride matrix and subsequently encased in inert paraffin wax, samples of 1 remain stable with no visible or spectroscopic degradation after several days under ambient conditions. The viability of this method for XAS measurements was further evaluated across a series of uranium compounds, ranging from uranyl species to highly air- and moisture-sensitive molecular complexes, at the uranium L 3 -edge. Edge energy determinations were highly reproducible (±0.1 eV between replicates) and, where available, showed excellent agreement with literature values. In conclusion, this low-cost, effective, and versatile method offers a viable solution for XAS studies of air-sensitive compounds and materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

3D Printing of Highly Porous Polypropylene Separators for Lithium‐Ion Batteries Using Fused Deposition Modeling and Thermally Induced Phase Separation

Appearing as one of the key-components of lithium-ion batteries (LIBs), this work specifically focuses on the additive manufacturing (AM) of custom-shape separators, facilitated by the filament material extrusion process, also called fused deposition modeling (FDM). The development and optimization of composite thermoplastic filament feedstocks combining polypropylene and paraffin wax, followed by the 3D printing of the separator membranes is shown. A post-processing step, based on thermal induced phase separation (TIPS), is introduced to promote porosity formation through removal of the paraffin wax sacrificial phase within the 3D printed items. Separators with different polypropylene/paraffin wax ratios are developed and the impact on printability, mechanical strength, porosity, and electrochemical performances, is thoroughly discussed. X-ray micro-computed tomography is employed to assess the geometric fidelity and to detect printing defects in a complex 3D lattice structure. The performance of the 3D printed porous separators is also compared to a commercial separator. This pioneering research establishes a foundation for the creation of porous separators that can adapt to and conform into 3D printed battery architectures with novel form factors, and also creates opportunities for the use of FDM and TIPS for a wide range of applications that employ porous structures beyond the energy storage field.

3D printing↗
NASA NTRS2012

Mechanical and Combustion Performance of Multi-Walled Carbon Nanotubes as an Additive to Paraffin-Based Solid Fuels for Hybrid Rockets

Paraffin-based solid fuels for hybrid rocket motor applications are recognized as a fastburning alternative to other fuel binders such as HTPB, but efforts to further improve the burning rate and mechanical properties of paraffin are still necessary. One approach that is considered in this study is to use multi-walled carbon nanotubes (MWNT) as an additive to paraffin wax. Carbon nanotubes provide increased electrical and thermal conductivity to the solid-fuel grains to which they are added, which can improve the mass burning rate. Furthermore, the addition of ultra-fine aluminum particles to the paraffin/MWNT fuel grains can enhance regression rate of the solid fuel and the density impulse of the hybrid rocket. The multi-walled carbon nanotubes also present the possibility of greatly improving the mechanical properties (e.g., tensile strength) of the paraffin-based solid-fuel grains. For casting these solid-fuel grains, various percentages of MWNT and aluminum particles will be added to the paraffin wax. Previous work has been published about the dispersion and mixing of carbon nanotubes.1 Another manufacturing method has been used for mixing the MWNT with a phenolic resin for ablative applications, and the manufacturing and mixing processes are well-documented in the literature.2 The cost of MWNT is a small fraction of single-walled nanotubes. This is a scale-up advantage as future applications and projects will require low cost additives to maintain cost effectiveness. Testing of the solid-fuel grains will be conducted in several steps. Dog bone samples will be cast and prepared for tensile testing. The fuel samples will also be analyzed using thermogravimetric analysis and a high-resolution scanning electron microscope (SEM). The SEM will allow for examination of the solid fuel grain for uniformity and consistency. The paraffin-based fuel grains will also be tested using two hybrid rocket test motors located at the Pennsylvania State University s High Pressure Combustion Lab.

Larson, Daniel B.↗
NASA NTRS2012

Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

Many approaches have been considered in an effort to improve the regression rate of solid fuels for hybrid rocket applications. One promising method is to use a fuel with a fast burning rate such as paraffin wax; however, additional performance increases to the fuel regression rate are necessary to make the fuel a viable candidate to replace current launch propulsion systems. The addition of energetic and/or nano-sized particles is one way to increase mass-burning rates of the solid fuels and increase the overall performance of the hybrid rocket motor.1,2 Several paraffin-based fuel grains with various energetic additives (e.g., lithium aluminum hydride (LiAlH4) have been cast in an attempt to improve regression rates. There are two major advantages to introducing LiAlH4 additive into the solid fuel matrix: 1) the increased characteristic velocity, 2) decreased dependency of Isp on oxidizer-to-fuel ratio. The testing and characterization of these solid-fuel grains have shown that continued work is necessary to eliminate unburned/unreacted fuel in downstream sections of the test apparatus.3 Changes to the fuel matrix include higher melting point wax and smaller energetic additive particles. The reduction in particle size through various methods can result in more homogeneous grain structure. The higher melting point wax can serve to reduce the melt-layer thickness, allowing the LiAlH4 particles to react closer to the burning surface, thus increasing the heat feedback rate and fuel regression rate. In addition to the formulation of LiAlH4 and paraffin wax solid-fuel grains, liquid additives of triethylaluminum and diisobutylaluminum hydride will be included in this study. Another promising fuel formulation consideration is to incorporate a small percentage of RDX as an additive to paraffin. A novel casting technique will be used by dissolving RDX in a solvent to crystallize the energetic additive. After dissolving the RDX in a solvent chosen for its compatibility with both paraffin and RDX, the mixture will be combined with the melted paraffin. With the melting point of the paraffin far below the decomposition temperature of the RDX, the solvent will be boiled off, leaving the crystallized RDX embedded in the paraffin. At low percentages of RDX additive and with crystallized RDX surrounded by paraffin, the fuel grains will remain inert, maintaining a key benefit of hybrids in the safety of the solid fuel.

Larson, Daniel B.↗
NASA NTRS2012

Formulation, Casting, and Evaluation of Paraffin-Based Solid Fuels Containing Energetic and Novel Additives for Hybrid Rockets

This investigation studied the inclusion of various additives to paraffin wax for use in a hybrid rocket motor. Some of the paraffin-based fuels were doped with various percentages of LiAlH4 (up to 10%). Addition of LiAlH4 at 10% was found to increase regression rates between 7 - 10% over baseline paraffin through tests in a gaseous oxygen hybrid rocket motor. Mass burn rates for paraffin grains with 10% LiAlH4 were also higher than those of the baseline paraffin. RDX was also cast into a paraffin sample via a novel casting process which involved dissolving RDX into dimethylformamide (DMF) solvent and then drawing a vacuum on the mixture of paraffin and RDX/DMF in order to evaporate out the DMF. It was found that although all DMF was removed, the process was not conducive to generating small RDX particles. The slow boiling generated an inhomogeneous mixture of paraffin and RDX. It is likely that superheating the DMF to cause rapid boiling would likely reduce RDX particle sizes. In addition to paraffin/LiAlH4 grains, multi-walled carbon nanotubes (MWNT) were cast in paraffin for testing in a hybrid rocket motor, and assorted samples containing a range of MWNT percentages in paraffin were imaged using SEM. The fuel samples showed good distribution of MWNT in the paraffin matrix, but the MWNT were often agglomerated, indicating that a change to the sonication and mixing processes were required to achieve better uniformity and debundled MWNT. Fuel grains with MWNT fuel grains had slightly lower regression rate, likely due to the increased thermal conductivity to the fuel subsurface, reducing the burning surface temperature.

Larson, Daniel B.↗
NASA NTRS2010

Phase Change Material Trade Study: A Comparison Between Wax and Water for Manned Spacecraft

Phase change material heat sinks have been recognized as an important tool in optimizing thermal control systems for space exploration vehicles and habitats that must deal with widely varying thermal loads and environments. In order to better focus technology investment in this arena, NASA has supported a trade study with the objective of identifying where the best potential pay-off can be found among identified aqueous and paraffin wax phase change materials and phase change material heat sink design approaches. The study used a representative exploration mission with well understood parameters to support the trade. Additional sensitivity studies were performed to ensure the applicability of study results across varying systems and destinations. Results from the study indicate that a water ice PCM heat sink has the potential to decrease the equivalent system mass of the mission s vehicle through a combination of a smaller heat sink and a slight 5% increase in radiator size or the addition of a lightweight heat pump. An evaluation of existing and emerging PCM heat sink technologies indicates that further significant mass savings should be achievable through continued development of those technologies. The largest mass savings may be realized by managing the location of the liquid and the solid in the heat sink to eliminate the melting and freezing pressure of wax and water, respectively, while also accommodating the high structural loads expected on future manned launch vehicles.

Quinn, Gregory↗
NASA NTRS2011

Phase Change Material Trade Study: A Comparison Between Wax and Water for Manned Spacecraft

Phase change material heat sinks have been recognized as an important tool in optimizing thermal control systems for space exploration vehicles and habitats that must deal with widely varying thermal loads and environments. In order to better focus technology investment in this arena, NASA has supported a trade study with the objective of identifying where the best potential pay-off can be found among identified aqueous and paraffin wax phase change materials and phase change material heat sink design approaches. The study used a representative exploration mission with well understood parameters to support the trade. Additional sensitivity studies were performed to ensure the applicability of study results across varying systems and destinations. Results from the study indicate that replacing a wax PCM heat sink with a water ice PCM heat sink has the potential to decrease the equivalent system mass of the mission s vehicle through a combination of a smaller heat sink and a slight 5% increase in radiator size or the addition of a lightweight heat pump. An evaluation of existing and emerging PCM heat sink technologies indicates that further mass savings should be achievable through continued development of those technologies. The largest mass savings may be realized by eliminating the melting and freezing pressure of wax and water, respectively.

Quinn, Gregory↗
DOE OSTI2023

Thermal conductivity measurement using modulated photothermal radiometry for nitrate and chloride molten salts

Molten salts are being used or explored for thermal energy storage and conversion systems in concentrating solar power and nuclear power plants. Thermal conductivity of molten salts is an important thermophysical property dictating the performance and cost of these systems, but its accurate measurement has been challenging, as evidenced by wide scattering of existing data in literature. The corrosive and conducting nature of these fluids also leads to time consuming sample preparation processes of many contact-based measurements. Here, in this work, we report the measurement of thermal conductivity of molten salts using a modulated photothermal radiometry (MPR) technique, which is a laser-based, non-contact, frequency-domain method adopted for molten salts for the first time. By unitizing the advantages of front side sensing of frequency-domain measurements and the vertical holder orientation, the technique can minimize the natural convection and salt creeping effects, thus yielding accurate molten salt thermal conductivity . The MPR technique is first calibrated using standard molten materials including paraffin wax and sulfur. It is then applied on measuring pure nitrate salts (NaNO 3 and KNO 3 ), solar salt (NaNO 3 –KNO 3 mixture), and chloride salt (NaCl–KCl–MgCl 2 ). The measurement results are compared with data from literature, especially those obtained from laser flash analysis (LFA). Our results demonstrate that the MPR is a convenient and reliable technique of measuring thermal conductivity of molten salts. Accurate thermal conductivity data of molten salts will be valuable in developing the next-generation high-temperature thermal energy storage and conversion systems.

14 SOLAR ENERGY↗
DOE OSTI2023

In Situ Synchrotron X-ray Scattering Investigation of Cathodic ZIF-8 Deposition on Graphite Using 3D-Printed Cells

Electrochemical approaches provide unique means to fabricate thin films of metal organic frameworks (MOFs). However, the kinetics of electrochemical MOF deposition has not been quantitatively investigated so far. In this study, we report the first in situ measurements of electrochemical MOF growth using transmission synchrotron X-ray scattering. Electrochemical cells based on poly(lactic acid) with two windows were fabricated using fused-deposition modelling. Here, the resulting 3D-printed cells, the surface of which was coated with paraffin wax to prevent solvent percolation through the polymer material, were used to monitor the cathodic growth of zeolitic imidazolate framework-8 (ZIF-8) on graphite in a methanol solution containing ZnCl 2 and 2-methylimidazole (Hmim) at different cathodic potentials. The resulting time-resolved X-ray diffraction data showed a gradual increase in crystal size with negligible changes in crystal orientation during the cathodic ZIF-8 deposition. More importantly, the time-resolved data provided a means to quantitatively assess the kinetics of the cathodic ZIF-8 growth using the Gualtieri model, revealing that the cathodic potential and Hmim concentration affected crystal growth kinetics, but not nucleation kinetics. These ZIF-8 samples exhibited changes in X-ray diffraction pattern after being washed with methanol and dried in air, indicating that in situ measurements are essential to investigate mechanisms behind MOF electrodeposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Mitigating electrochemical degradation in CsPbBr{sub 3} gamma detectors by organic and inorganic encapsulation.

CsPbBr3 perovskite semiconductors have emerged as a leading candidate for nextgeneration radiation detectors because of their exceptional charge transport properties, defect tolerance, and record-breaking sensitivity and energy resolution. Their long-term stability, however, is hindered by electrode-driven electrochemical decomposition, which is accelerated by moisture- and oxygen-assisted ion migration during operation. Here, we investigated organic and inorganic encapsulation strategies as both environmental barriers and means to suppress interfacial degradation pathways. Atomic layer deposition (ALD) of Al2O3 provided a conformal passivation layer that blocked environmental ingress, suppressed ionic diffusion, reduced leakage current, enhanced energy resolution and expanded the operational electric-field window beyond 5 kV∙cm1 . By contrast, organic encapsulants such as paraffin wax and polystyrene slowed moisture diffusion but did not suppress interfacial reactions, with wax extending stability to over 90 days. These results show that ALD-Al2O3 suppresses dominant interfacial degradation pathways, enabling stable, high-field operation and advancing the practical deployment of CsPbBr3 γ-ray detectors.

Unal, Mustafa↗
DOE OSTI2025

Data-Driven Discovery of Bimetallic Nanoparticles Catalysts for the Hydrogenolysis of Polyethylene

Supported platinum nanoparticles are known to convert polyolefins to high-quality liquid hydrocarbons with hydrogen under relatively mild conditions. However, no systematic study has been undertaken using bimetallic catalysts for polyethylene upcycling. Specifically, a total of 98 monometallic and bimetallic combinations (Ag, Cr, Co, Cu, Fe, Ga, In, Mn, Ni, Pd, Pt, Rh, Ru, Zr) on alumina were synthesized utilizing surface organometallic chemistry (SOMC) technique via robotic platform. These were investigated at a small scale (10 mg of catalyst and 50 mg of polyethylene) for their activity for the hydrogenolysis of polyethylene in a high-throughput batch reactor. Combinations of Ni and Co were selected as candidates with high activity toward conversion into paraffin oils. Reaction conditions were optimized with Ni/Co/Al 2 O 3 catalyst at a larger scale (300 mg catalyst and 3 g polyethylene) to obtain a high yield (93.1%) of paraffin wax with desired properties (M n = 380 Da) and low polydispersity (Đ = 1.2). Ni/Co/Al 2 O 3 was compared against Co/Ni/Al 2 O 3 to understand the role of the deposition sequence. When Co is deposited before Ni, a layer of cobalt aluminate is formed upon reduction, stabilizing the deposition of 5 nm metallic Ni particles. When nickel is deposited before Co, particles are larger (average >20 nm) and more oxidized (Ni δ+ in NiAl 2 O 4 ), decreasing the availability of the catalytically active metallic Ni. In conclusion, the difference in electronic environments was also described by DFT calculations, which revealed that smaller 3D clusters of Ni are preferred on CoAl2O4 over the 3D clusters on NiAl 2 O 4 and that these smaller clusters are more reducible, as confirmed experimentally.

Polymer↗
DOE OSTI2024

Characterization of wood fiber insulation for the development of wood fiber-insulated panels (WIPs) for use in building envelope

Wood fiber insulation (WFI) was studied as an eco-friendly alternative for fossil-based building insulation, focusing on its use in new wood fiber-insulated panels (WIPs). Rigid WFI boards with densities of 110, 140, and 180 kg/m³, including a 140 kg/m³ variant without paraffin wax, were evaluated. Key properties investigated included porosity, water vapor transmission, liquid water adsorption, and thermal conductivity. The porosity ranged between 85 and 92%, primarily influenced by density. Water vapor permeability ranged from 65 to 90 ng·s-1m-1Pa-1, while liquid water absorption was between 2.5 and 20% by volume, influenced by both wax and density. The thermal conductivity coefficient ranged from 0.038 to 0.055 W/(m·K). Bond strength tests with WFI (140 kg/m³ with wax) laminated to various materials using structural adhesives showed tensile perpendicular-to-grain strengths of 10 to 16 kPa and shear strengths of 60 to 90 kPa, with failure only occurring within the WFI. It was concluded that WFI is a promising material for novel WIPs, offering competitive hygrothermal properties and compatibility with structural adhesives. However, its bio-based nature suggests variability and complexity, necessitating further rigorous testing in various climates and in more complex assemblies.

Materials Science↗
DOE OSTI2023

Thermal Conductivity of a Novel Salt-Hydrogel Complex as a Phase Change Material for Building Thermal Management

Use of electricity for space heating, ventilation and air conditioning in buildings may be better managed through temporary energy storage. Compared with electrochemical storage, the levelized cost of thermal energy storage systems can be lower depending on geographical location and thermophysical properties [1]. In any phase change material (PCM), the rate of absorption and release of thermal energy increases with higher thermal conductivity [2]. However, leading PCMs like paraffin waxes have thermal conductivities on the order of 0.1 W/mK. Glauber’s salt, a salt hydrate, possesses a relatively high thermal conductivity but suffers from supercooling and phase segregation. Research has shown that polymer-based composites with salt hydrates can prevent phase segregation and limit supercooling over hundreds of cycles [3] though the thermal conductivity of the composite may be reduced leading to low energy storage rates. Here, we report thermal conductivity measurements on polymer hydrogels which are stable in solutions of Glauber’s salt. To measure thermal conductivity of soft gels, we use a 3-omega method [4] where heat flows bidirectionally through a substrate below and through a gel placed on top. This suits measurements of both gels and liquids unlike transient plane heat source or transient hot wire methods. We report measurements of thermal conductivity of salt-hydrogel complexes as a function of temperature, cross-linking and salt concentration. In addition, we present modeling of thermal conductivity of sodium sulfate solutions with available theories. We finally employ polarized optical microscopy to observe inside the transparent hydrogel networks, showing that precipitating crystals may influence thermal conductivity measurements for high salt concentrations. Our thermal conductivity results combined with enthalpy of phase change, mass density and specific heat are essential to accurately design thermal storage systems for energy-efficient buildings.

composite, thermal conductivity↗