Waste derived polysulphide coating on fly ash as fillers in plastic composite
Not provided.
Construction & Building Technology↗
SEARCH · Search NASA
Results for “Plastic filler”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Coal-Waste-Enhanced Filaments for Additive Manufacturing of High-Temperature Plastics and Ceramic Composites
In the United States, coal waste from over a century of mining and burning coal for heat and electricity has accumulated as mountains of coal fly ash and bottom ash and acre-size ponds, coal fines and gob. These materials can be a problem for local communities and water systems. A cost-effective process to utilize high volumes of these coal wastes in a high-value product would be beneficial to those communities by reducing the amount of waste and providing jobs, manufacturing components, and materials from the waste. Many coal-to-products technologies (e.g., carbon fibers, graphene, carbon foam) rely on carefully choosing the starting material and then altering it chemically or thermally to make the products work. Due to the wide variability of composition and coal content in typical coal waste streams, many high-volume coal waste streams are likely to be unsuitable for use in those technologies. Semplastics’ technology has been shown to utilize most types of coal waste successfully without any pre-selection or pre-processing requirements other than a nominal particle-size reduction for wastes like bottom ash. This characteristic of Semplastics’ solution may enable the use of much larger volumes of a wider range of coal wastes than other coal-to-products technologies. In this project, Semplastics leveraged its unique experience with both coal waste (fly ash or coal combustion residuals), resin materials, and 3D printing to develop 3D printer filaments using common coal wastes – bituminous coal fines and fly ash – and researched the feasibility of using other forms of coal waste as fillers. Simple 3D-printed parts were successfully produced from the coal waste enhanced filaments, which were found to have improved strength and stiffness.
01 COAL, LIGNITE, AND PEAT↗
In situ investigation of high-pressure hydrogen-induced swelling in elastomers and its correlation with material properties
The resistance of elastomeric materials to high-pressure hydrogen-induced damage is essential for ensuring the reliability of hydrogen infrastructure. Here, in this study, we systematically investigated the swelling behavior and hydrogen transport properties of four elastomer types – EPDM, NBR, FKM, and HNBR – using a custom in-situ view cell system capable of real-time monitoring during decompression from pressures up to 96.5 MPa. Each elastomer was formulated with and without fillers and plasticizers to assess the effects of formulation on swelling response. Thermal desorption analysis (TDA) was employed to determine equilibrium hydrogen content and diffusion coefficients, providing insight into gas uptake and mobility within each material. Correlation analyses using Pearson and Spearman coefficients revealed that the diffusion coefficient showed a stronger relationship with swelling behavior than hydrogen content, highlighting the dominant role of hydrogen mobility. Filled elastomers, particularly those with carbon black, consistently showed reduced swelling due to enhanced stiffness and reduced diffusivity. These results deepen our understanding of diffuso-mechanical interactions in elastomers and support the rational design of sealing materials for high-pressure hydrogen systems.
EPDM↗
Structure and Flow-Viscosity of Filled-Polymer-Based 3D Printing Ink: Exploration through Coarse-Grained Molecular Dynamics
The addition of nanofiller particles to a polymer matrix has long been known to enhance or modify the composite’s mechanical and rheological properties. However, quantitatively capturing such changes with molecular level simulations remains computationally challenging. Toward that goal, we performed coarse-grained molecular dynamics of a nanocomposite system at a fixed (25 vol %) filler loading under nonspecific, weak polymer–filler interactions representative of a broad class of technologically important materials. We report several interesting results, including: (1) the equilibrium chain-configuration remains Gaussian-like as in an unfilled melt; (2) smaller filler particles display a stronger tendency to cluster; (3) larger fillers act as plasticizers by reducing the entanglement density and accelerating the chain mobility; and (4) fillers enhance the tensile response modulus, with the effect being stronger for larger particles. We also simulate cluster breakup, yielding, and elongational flow under an applied time-linear tensile strain and study the flow viscosity as a function of filler-size and chain-length.
Materials science↗
Influence of functional additives, fillers, and pigments on thermal and catalytic pyrolysis of polyethylene for waste plastic upcycling
Pyrolysis offers a relatively green and economical method to convert waste plastics into valuable chemicals and fuels without the need for harmful solvents, toxic chemicals, or costly high-pressure reactors. Despite its popularity among chemical upcycling technologies, industrial adoption suffers from feedstock heterogeneity, low-quality products, and catalyst deactivation. Most plastics in our daily lives are formulated with functional additives, fillers, and colorants. These additives remaining in end-of-life waste streams increase feedstock heterogeneity, creating a challenging issue in recycling plastics. Still, the potential impacts of additives on the chemical upcycling of plastics have been poorly understood. In this study, polyethylene compounded with a range of widely used additives (antioxidants, stabilizers, pigments, fillers, slip agents, and flame retardants) was subjected to both thermal pyrolysis and catalytic pyrolysis in different catalyst-to-feedstock contact modes. It showed that many inorganic additives, such as talc, kaolin, CaCO 3 , TiO 2 , carbon black, and zinc stearate, facilitated polymer decomposition during pyrolysis, increasing light hydrocarbons while also promoting aromatic and carbon residue formation. Conversely, antioxidants and stabilizers inhibited depolymerization, favoring heavier hydrocarbons. During catalytic pyrolysis with HZSM-5 zeolite, additives strongly enhanced aromatic and catalytic coke formation, especially when there was direct contact between plastics and catalysts. Although certain additives seem beneficial in the short term by promoting polymer cracking and improving the selectivity of aromatics, the transport of the additives and their degradation products and increased carbon coking can contaminate products, deactivate or modify catalysts, and foul reactors. These findings address a critical knowledge gap in effectively converting waste plastics via a greener route.
42 ENGINEERING↗
Tunable structure and reinforcement of polyvinyl alcohol (PVA) hydrogels using fungal chitin particles
Polysaccharides, including chitin, are one of the most abundant biopolymers in nature and are increasingly recognized as a sustainable alternative to petroleum-derived plastics and synthetic fillers in polymer composites. Traditionally sourced from crustacean shells, chitin offers mechanical strength and biocompatibility with limitations also in processability and functionality. Fungal-derived chitin material represents a promising alternative, with advantages including scalable fermentation on low-cost substrates, absence of shellfish allergens, and tunable molecular architectures that vary by species, developmental stage, and growth environment. Here, in this study, we systematically examined chitinous materials obtained from taxonomically and functionally distinct fungi, Laccaria bicolor, Trichoderma reesei and Rhizopus oryzae, to assess their structural, chemical, and morphological properties as reinforcement agents in polymer composites. Mild alkaline pretreatment was employed to obtain mycelium chitin particles, thereby improving accessibility to chitin and co-occurring β-D-glucans while maintaining microparticle integrity. Comprehensive FTIR and solid-state NMR analyses revealed species-specific differences in chemical composition and microstructure, with R. oryzae exhibiting a unique spectral signature. These fungal-derived chitin were then incorporated into poly(vinyl alcohol) (PVA) hydrogels, where they acted as reinforcing fillers without the need for additional chemical crosslinkers. Comparative evaluation of hydrogel properties demonstrated that fungal chitin significantly enhanced mechanical performance, with all mycelium fillers mitigating the water weakening in PVA hydrogels. R. oryzae-derived composites tripled the hydrogel tensile strength while the submicron fibrous morphology in L. bicolor contributes to over 45 % tensile improvement in dry PVA composites. Our findings highlight the potential of fungal biomass as a tunable, sustainable platform for producing chitin-based reinforcing agents.
Chitin↗
Surface Modified Fly Ash for Value Added Products (SuMo Fly Ash)
The objective of this project is to develop a technology to encapsulate coal fly ash particles in sulfurized vegetable oil, enhancing physical and mechanical properties of the fly ash as a filler material when applied in commercial products. This project significantly advances the knowledge base and technology for synthesizing coated fly ash particles for application in different polymer matrices to increase cross-linking, compatibility, air-entrainment and to decrease the leaching potential of metals of concern. Specifically, the project focuses on (a) collection, and characterization of fly ash material from coal power plants; (b) development of Sulfurized Vegetable Oil (SVO) modified (SuMo) fly ash and their detailed characterization; (c) evaluation of the mechanical properties of the SuMo fly ash incorporated plastic and rubber composites for potential replacement of CaCO 3 or carbon black as filler materials with SuMo fly ash in plastic and rubber composites; (d) leaching potential of SuMo fly ash and SuMo fly ash-incorporated plastic and rubber composites to determine the rate of release of trace metals. The major findings of this project are: i) Sulfurized Vegetable Oil coated fly ash (SuMo fly ash) was successfully prepared with a particle size of ≤ 45 micron which exhibited hydrophobicity of contact angle > 90°; ii) the coating reduces leaching of metals (e.g., B, Cr) from fly ash when exposed to water; iii) incorporation of SuMo fly ash increases thermal stability and yield strength of plastics; iv) SuMo coating helps disperse fly ash particles into cured rubbers, natural rubber; (v) SuMo fly ash-incorporated plastic/cured rubbers compounds protects against leaching of toxic elements.
20 FOSSIL-FUELED POWER PLANTS↗
Material property characterization of 3D printed polypropylene wood plastic composites
Abstract Wood flour (WF) at 10 wt.% and 20 wt.% loadings was used as a reinforcing filler to enhance the applicability of polypropylene (PP) for 3D printing. After performing printability tests of PP wood plastic composites (WPCs), the mechanical properties of both injection‐molded and 3D‐printed PP WPC specimens were explored. Test specimens were prepared from 3D printed hexagons for analyzing the mechanical properties. Adding WF to neat PP increased the storage modulus and the glass transition temperature while decreasing the degree of crystallinity and the coefficient of thermal expansion, while enhancing the printability of neat PP. The tensile strength, tensile modulus of elasticity, flexural strength, and flexural modulus of elasticity of injection‐molded neat PP improved by up to 21%, 59%, 30%, and 56%, respectively, with 20 wt.% WF. However, the impact strength of injection‐molded neat PP decreased by 85%, with 20 wt.% WF. After 3D printing, the tensile strength and tensile modulus of elasticity of printed neat PP increased by up to 84% and 60%, respectively, with 20 wt.% WF. The flexural strength and flexural modulus of elasticity of neat printed PP remained unchanged compared to those of PP filled with 20 wt.% WF, while the impact strength decreased by 87%. Highlights WF was used as a reinforcement in polypropylene designed for 3D printing A pilot‐scale, pellet‐fed 3D printer was used to print hollow hexagons, and then test specimens were fabricated from these hexagons for mechanical properties The tensile and flexural properties of 3D printed neat polypropylene improved, while the impact strength decreased after adding 20 wt.% WF to the neat PP.
Hwang, Sungjun↗
Impact of melt viscosity on filler dispersion in elastomeric nanocomposites
Compounding of commercial nanocomposites usually involves the addition of viscosity enhancers such as binder resins in ink jet inks, and paints. Contrary to this, plasticizers such as process oils are added to reduce the melt viscosity and ease processability of reinforced elastomers. Nanofillers such as silica and carbon black are typically added to reinforce rubber and enhance performance of automotive tire treads. Filler dispersion has traditionally been qualitatively (indirectly) assessed by measuring the properties of reinforced elastomers. While dispersion can be quantified by examining filler agglomeration through surface roughness measurements and microscopy, the size-scale dependence for these hierarchical fillers has usually been ignored. Here, we have recently devised a method to quantify nano-scale dispersion of fillers using Ultra small-angle X-ray scattering (USAXS) techniques. This method is advantageous since it directly links the controllable processing/compounding parameters such as the mixing speed, mixer geometry, residence time (or mixing duration), melt density, flow gap distance, and melt viscosity to nano-scale dispersion. While our previous studies have explored the impact of different processing parameters, this study specifically investigates the impact of melt viscosity on nano-scale filler dispersion in elastomer compounds. Commercially available polybutadienes with different Mooney viscosities were used in conjunction with different grades and amounts of process oils to modify the melt viscosity.
Carbon black↗
Experimental Comparison of Elastomeric Materials for Hydraulic Seal Durability under Reciprocating Conditions
Wave Energy Converters (WECs) rely on hydraulic Power Take-Off (PTO) systems to transform the kinetic energy of ocean waves into electricity, where hydraulic seals play a critical role in preventing fluid leakage and ensuring watertight operation under harsh marine conditions. However, seal degradation due to wear, fatigue, and corrosion remains a key challenge limiting system reliability and increasing maintenance costs. In this study, the tribological performance of elastomeric materials for hydraulic sealing applications that are based on commercial polyurethane and custom-compounded Ethylene Propylene Diene Monomer (EPDM) is investigated. Using a CSM tribometer, reciprocating wear tests were conducted in accordance with ASTM G133 under dry sliding conditions, with normal loads ranging from 3 to 10 N, and sliding speeds of 10 to 30 mm/s. Coefficient of friction (COF), specific wear rate, and worn surface morphology are evaluated to understand how load, velocity, and material composition affect seal durability. Improved wear stability and high Shore A hardness (93–94) were demonstrated by the commercial thermoplastic polyurethane (Duralast 4203 and 4758). EPDM-based compounds showed different filler-dependent behaviors, formulations filled with carbon black (E3) had the lowest wear rate (1.45 × 10?4 mm³ N?¹ m?¹) and increased load-bearing capacity, while samples modified with silica and plasticizer (E4, E5) had better conformability and damping but less hardness. Compounded EPDMs showed wider deformation zones because of their lower modulus and filler-matrix interfacial fluctuations, while commercial grades exhibited shallower wear scars (= 380 µm), according to optical profilometry. The Archard model-based lifetime estimation showed that, under 10 N and 30 mm/s, operational endurance ranged from 3.1 to 6.2 years. Because of its low wear rate and steady interfacial behavior, E3 had the longest anticipated life. For medium-load hydraulic sealing applications, these results demonstrate the possibility of customized EPDM formulations as affordable substitutes for commercial polyurethanes. They also offer a quantitative foundation for material selection and lifespan prediction.
Durability↗
Carbon Fiber-Based Vitrimer Composites: A Path toward Current Research That Is High-Performing, Useful, and Sustainable
In the polymeric material industry, thermosets and related composites have played a substantial role in the production of rubber and plastics. One important subset of these is thermoset composites with carbon reinforcement. The incorporation of carbon fillers and fibers gives polymeric materials improved electrical and mechanical properties, among other benefits. However, the covalently crosslinked network of thermosets presents significant challenges for recycling and reprocessing because of its intractable nature. The introduction of vitrimer materials opens a new avenue to produce biodegradable and recyclable thermosets. Carbon-reinforced vitrimer composites are pursued for high-performance, long-lasting materials with attractive physical properties, the ability to be recycled and processed, and other features that respond uniquely to stimuli. The development of carbon-reinforced vitrimer composites over the last few years is summarized in this article. First, an overview of vitrimers and the methods used to prepare carbon fiber-reinforced vitrimer composites is provided. Because of the vitrimer nature of such composites, reprocessing, healing, and recycling are viable ways to greatly extend their service life; these approaches are thoroughly explained and summarized. The conclusion is our prediction for developing carbon-based vitrimer composites.
36 MATERIALS SCIENCE↗
Effects of chemical composition and physicochemical properties of poplar biomass on the performance of 3D printed poplar-reinforced PLA materials
Lignocellulosic biomass has been well-acknowledged as a filler for making 3D printed composites. The technical performances of composites were influenced by the characteristics of the components. The correlations between poplar biomass properties and the mechanical and thermal performances of the 3D printed poplar-plastic composites were investigated. The characteristics of poplar were modified by different pretreatment methods, including using hot water, dilute acid, and organic solvent (organosolv), and each treated poplar biomass was applied as a filler in a polylactic acid (PLA) polymer matrix to produce eco-friendly materials. These solvent pretreatments increased the hydrophobicity and surface area of poplar. Organosolv treated poplar showed the highest cellulose content and significantly increased Young's modulus of its biocomposites. Principal component analysis revealed that the specific surface area and water contact angle of biomass contributed to the thermal stability of biocomposites. Additionally, the degree of polymerization of cellulose and xylan content within the biomass correlated with the biocomposites' break stress. Notably, the crystallinity of biocomposites impacted the modulus of these materials. The reported relationships between biomass characteristics and 3D printed composite behaviors provide guidance for optimizing biomass processing in biocomposite applications.
Ji, Anqi [State Univ. of New York (SUNY), Syracuse↗
Creep suppression and fatigue in bio-based composites manufactured via conventional and large format additive manufacturing processes
The emergence of novel extrusion-based additive manufacturing (AM) processes has prompted the development of new thermoplastic composite feedstocks, and broadening sustainability initiatives have driven the development of bio-based and recyclable material for AM feedstocks. Poly(lactic acid) (PLA) with wood flour (WF) is one composite system that has been demonstrated in numerous AM applications, as well as traditional processing methods (i.e., compression and injection molding); however, there has been a need to understand how the variation in processing methodology impacts the material performance of these bio-based feedstocks from a fundamental perspective, with particular emphasis on creep for an extended application use-life. Herein, PLA/WF is explored as a feedstock material for large format additive manufacturing (LFAM) and the performance of additively manufactured materials is compared to those produced via more traditional processing methods. It is also demonstrated that the addition of WF decreases the material’s coefficient of thermal expansion (CTE) while increasing its Young’s modulus, susceptibility to water uptake, and creep fatigue resistance. Essentially, the addition of 20 wt% WF results in a 92 % decrease in rubbery regime CTE while simultaneously resulting in a 14 % increase in modulus, 190 % increase in water uptake, and a 31 % decrease in residual strain after cyclic creep tests. The processing method was also found to play a large role in the final part performance, with the printed material increasing the crystallinity by 183 % and 214 % compared to its compression and injection molded counterparts. Furthermore, the porosity of printed samples increased by two orders of magnitude compared to samples prepared via traditional processing methods.
36 MATERIALS SCIENCE↗
Generalizable Porous Aromatic Framework‐Included Polymer Membranes for Diffusion‐Enhanced Gas Separations
Industrial separation processes account for 10-15% of global energy consumption. Membrane-based processes are less energy-intensive than traditional gas separation technologies; however, enhanced material separation performance and stability for numerous gas mixtures are needed for widespread industrial adoption. This work presents a generalizable strategy for preparing mixed-matrix gas separation membranes exceeding the performance upper bounds of existing polymer membranes for a wide variety of industrial gases. By incorporating robust porous aromatic framework (PAF) particles into various dense commercial polymer matrices, gas diffusivity and solubility can be enhanced. For diverse gas mixtures (e.g., CO2/N2, O2/N2, He/CH4, H2/N2, and C2H4/C2H6), the resulting composite membranes exhibit enhanced gas permeabilities-by as much as 520%-and largely unchanged selectivities even after 6 years of aging under simulated flue gas conditions. These improvements arise from the ultrahigh porosity, excellent chemical compatibility, and unique physicochemical properties of the embedded PAF particles. Functionalizing the PAFs with polyamines also enables composite membranes that achieve among the highest reported performances against plasticization, a common obstacle in commercializing gas separation membranes. Significantly, the PAF-1 particles are readily dispersible in various common membrane casting solvents, suggesting their broader utility as a filler for designing high-performance membranes for many industrial gas separations.
Uliana, Adam A↗
Harnessing biomass-derived reinforcements for sustainable flame-resistant composite
Bio-based composites containing natural fiber reinforcements have been integral to developing innovative, low-cost, and low-energy technologies for transportation applications in marine, automotive, and other industries. The low density of natural fibers gives these materials a high specific stiffness and strength, which can lead to significant weight savings in composites. This study focused on a specialty type of wood fiber treated with boric acid (≤ 7%) sourced from Northern White Pine in the USA, marketed as TimberFill. TimberFill is a high aspect ratio, fibrillated wood fiber that is produced commercially for wood fiber insulation; it is chemically treated to improve both its flame retardance and water resistance. In the present study, TimberFill was processed into non-woven mats using a process akin to papermaking and then infiltrated with epoxy resin. Biochar from wood waste was also incorporated into the epoxy resin as a low-cost filler and functional additive. The effects of biochar concentration on composites’ flame retardance (17% improvement in burn rate), thermal conductivity (improved by 9%), and mechanical performance (33% improvement in modulus) are herein presented. Additionally, it explores the plasticizing effect of the boric acid used in the treatment of TimberFill on the thermal and mechanical properties of the resulting composites, specifically on the thermal expansion coefficient.
Joshy, Joslin [ORNL]↗
Elucidating the impact of fiber source on polypropylene/hemp composite performance for the automotive industry
Given their high strength-to-weight ratio, there is an ever-increasing volume of plastics being used in the automotive industry as plastics aid in the charge to lightweight vehicles for improved fuel efficiency. However, these plastics are often landfilled at their end-of-life, which has given rise to the demand for sustainable materials and waste management alternatives compared to purely synthetic systems. Natural fiber composites have been explored as a viable material option to reduce the environmental impact of plastic use in automobiles while simultaneously ensuring the part performance is not sacrificed. Herein, we explored the use of hemp/polypropylene (PP) composites in which US-sourced hemp is compared to internationally sourced and industrially available hemp. There appears to be a minimal impact on the composite properties regardless of fiber sourcing, and the addition of a natural filler to the PP matrix results in up to a 367% increase in Young's modulus, 126% increase in heat deflection temperature, and comparable water uptake performance. It should be noted that the natural filler addition does increase density by up to 13% due to the higher density of natural fibers compared to the low-density PP matrix. A modified rule of mixtures calculation revealed that the composite materials produced in this study demonstrated good agreement with analytical modeling. Finally, a screening analysis was performed exploring the transportation of hemp fibers, and the results build a strong case for regionalized manufacturing of automotive parts.
Hubbard, Amber M. [Oak Ridge National Laboratory (↗
Polylactic acid (PLA)-based multifunctional and biodegradable nanocomposites and their applications
Polylactic acid (PLA)-based nanocomposites are emerging as multifunctional, biodegradable materials, offering sustainable alternatives to petroleum-based plastics. This review examines recent advancements in PLA nanocomposites, focusing on enhanced mechanical strength, thermal stability, and biodegradability achieved through nanofillers like metallic particles, carbon-based materials, and ceramics. Techniques such as in situ polymerization, melt mixing, and electrospinning enable application-specific improvements. PLA's limitations, including brittleness and low barrier properties, are addressed to support diverse applications: in packaging (e.g., extended shelf life), biomedicine (e.g., degradable implants), and electronics (e.g., flexible devices). Despite challenges with filler dispersion and thermal resistance, continued innovations expand PLA's potential across multiple industries, contributing to a sustainable, circular economy.
Biodegradable polymers↗
A comprehensive review on valorization of chestnut processing wastes into bio‐based composites and bioplastics
Abstract This review examines the characterization and utilization of chestnut processing wastes (35%) in the production of bioplastics and biocomposites. In this review, a Web of Science search without any publishing year restriction on the biochemical compositions of all the components of Castanea sativa . The obtaining of bioplastics and biocomposites based on C. sativa was reviewed. First, it highlights the biochemical composition and antioxidant properties of chestnut fruit, shell, burrs, leaves, flowers, and wood focusing on the most important compounds, such as phenolic acids, flavonoids, carbohydrates, Klason lignin, cellulose, and glucan, which can enhance the properties of these materials. Then the review covers using several chestnut extracts and fillers in bioplastics production through solvent casting technique. The mechanical, structural, bioactive properties, and moisture content were optimized through the composition and production. The color, UV absorption, antioxidant, and antimicrobial activity were also discussed. Biocomposites reinforced with chestnut burs, shells, or wood flour increased the intended properties. The enhancements in tensile strength, elastic modulus, and the effects of a pre‐treatment were evaluated. Additionally, it discusses material recovery, recycling, and reuse, particularly how it affects the biodegradability of composites incorporating chestnut waste residues. Highlights Chestnut fruit, shells, and burrs are rich in starch, lignin, and cellulose. The waste of chestnut processing can be used in bioplastics and biocomposites. Chestnut‐based films and biocomposites exhibit promising mechanical properties. The antimicrobial activity, making films, and composites proper for food packaging. New techniques boost performance, offering alternatives to conventional plastics.
Silva, Simão B. [REQUIMTE/LAQV, ISEP, Polytechnic ↗