Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polyacrylic acid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The Bonding Nature and Adhesion of Polyacrylic Acid Coating on Li-Metal for Li Dendrite Prevention

The success of polyacrylic acid (PAA) to suppress Li dendrite growth suggests that the mechanical properties of polymer-based coatings, including the modulus, toughness, and interfacial adhesion are important design criteria. However, the measurement of the adhesion of thin PAA, as well as other polymer coatings to the reactive Li-metal anode surface is limited experimentally and challenging computationally. In this paper, a strategy was proposed to estimate the adhesion and delamination of the PAA(polymer)/Li interface, based on the bonding nature at the simpler PAA (oligomer)/Li interfaces using density functional theory calculations. It has been shown that the carboxylic acid groups in PAA reacted strongly with metallic Li, which significantly enhances the interfacial adhesion through the Li–O bonds formation, Li ionization and its incorporation into PAA, and –H or –OH termination of Li after decomposition of the COOH functional group. During delamination, it was found that the most likely PAA delamination route involved breaking partial Li–O bonds and lifting some ionized Li atoms from the Li-metal, especially for the Li atoms that showed a charge closer to +1 or are bonded with two O atoms from PAA. Based on the average bonding energies from PAA(oligomer)/Li interface delamination calculations, the work of separation, W sep , of the PAA(polymer)/Li interface was estimated to be ~1.0 (J/m 2 ). The high W sep of PAA (polymer)/Li was comparable with the Li 2 O/Li interface and higher than Li 2 CO 3 /Li and LiF/Li interfaces. This order correlated well with the areal density of Li–O bonds, which can serve as a descriptor for the interfacial adhesion. Furthermore, this computational approach can be applied to other interfaces with polymer-based coatings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

Ion exchange selectivity for cross-linked polyacrylic acid

The ion separation factors for 21 common metal ions with cross-linked polyacrylic acid were determined as a function of pH and the percent of the cross-linked polyacrylic acid neutralized. The calcium ion was used as a reference. At a pH of 5 the decreasing order of affinity of the ions for the cross-linked polyacrylic acid was found to be: Hg++, Fe+++, Pb++, Cr+++, Cu++, Cd++, Al+++, Ag+, Zn++, Ni++, Mn++, Co++, Ca++, Sr++, Ba++, Mg++, K+, Rb+, Cs+, Na+, and Li+. Members of a chemical family exhibited similar selectivities. The Hg++ ion appeared to be about a million times more strongly bound than the alkali metal ions. The relative binding of most of the metal ions varied with pH; the very tightly and very weakly bound ions showed the largest variations with pH. The calcium ion-hydrogen ion equilibrium was perturbed very little by the presence of the other ions. The separation factors and selectivity coefficients are discussed in terms of equilibrium and thermodynamic significance.

May, C. E.↗
DOE OSTI2020

Si-based materials for lithium-ion batteries VIII. 90% surface-modified Si/C-lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy was used to analyze a 90% Si/C-lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping Facility (CAMP), Argonne National Laboratory. The spectra were obtained using incident monochromatic Al K α radiation at 1486.6 eV (0.834 01 nm). An initial survey spectrum together with O 1s, C 1s, and Si 2p are presented. A final survey spectrum was collected to ascertain the amount of beam-induced damage, which appears to be minimal. Finally, the spectra indicate the principal core level photoelectron and Auger electron signals with only minor lithium signal and show the expected silicon-carbon species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure as well contributions related to the binder material.

25 ENERGY STORAGE↗
DOE OSTI2020

Si-based materials for lithium-ion batteries VI. 15% surface-modified Si/C-graphite/carbon black/lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy was used to analyze a 15%Si/C-graphite/carbon black/lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping Facility (CAMP), Argonne National Laboratory. The spectra were obtained using incident monochromatic Al K α radiation at 1486.6 eV (0.83 401 nm). An initial survey spectrum together with O 1s, C 1s, and Si 2p are presented. A final survey spectrum was collected to ascertain the amount of beam-induced damage, which appears to be minimal. The spectra indicate the principal core level photoelectron and Auger electron signals with only minor nitrogen and lithium signals and show the expected silicon-carbon species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure as well contributions related to the binder material.

17 WIND ENERGY↗
DOE OSTI2020

Si-based materials for lithium-ion batteries XI. 70% surface-modified Si/C/perfluorooctene-carbon black/lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy was used to analyze a 70% Si/C/perfluorooctene-carbon black/lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping (CAMP) Facility, Argonne National Laboratory. The spectra were obtained using incident monochromatic Al K α radiation at 1486.6 eV (0.83 401 nm). A survey spectrum together with O 1s, C 1s, and Si 2p are presented. The spectra indicate the principal core level photoelectron and Auger electron signals with only minor sodium, copper, calcium, and lithium signals and show the expected silicon-carbon, carbon-fluorine, and silicon-fluorine species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure.

25 ENERGY STORAGE↗
DOE OSTI2020

Si-based materials for lithium-ion batteries VII. 70% surface-modified Si/C-carbon black/lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy (XPS) was used to analyze a 70% Si/C-carbon black/lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping Facility (CAMP), Argonne National Laboratory. The spectra were obtained using incident monochromatic Al K α radiation at 1486.6 eV (0.834 01 nm). An initial survey spectrum together with O 1s, C 1s, and Si 2p are presented. A final survey spectrum was collected to ascertain the amount of beam-induced damage, which appears to be minimal. Finally, the spectra indicate the principal core level photoelectron and Auger electron signals with only minor copper, nitrogen, calcium, and lithium signals and show the expected silicon-carbon species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure as well contributions related to the binder material.

25 ENERGY STORAGE↗
DOE OSTI2020

Si-based materials for lithium-ion batteries IX: 70% surface-modified Si/C/polyethylene glycol-carbon black/lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy was used to analyze a 70% Si/C-carbon black/polyethylene glycol/lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping Facility (CAMP), Argonne National Laboratory. The spectra were obtained using incident monochromatic Al K α radiation at 1486.6 eV (0.834 01 nm). An initial survey spectrum together with O 1s, C 1s, and Si 2p are presented. A final survey scan was collected to ascertain the amount of beam-induced damage, which appears to be minimal. Finally, the spectra indicate the principal core level photoelectron and Auger electron signals with only minor copper and lithium signals and show the expected silicon-carbon species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure as well as contributions related to the binder material.

25 ENERGY STORAGE↗
DOE OSTI2020

Si-based materials for lithium-ion batteries X: 70% surface-modified Si/C/polyvinylidine difluoride-carbon black/lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy was used to analyze a 70% Si/C/polyvinylidine difluoride/carbon black/lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping Facility (CAMP), Argonne National Laboratory. The spectra were obtained using incident monochromatic Al Kα radiation at 1486.6 eV (0.834 01 nm). A survey spectrum together with O 1s, C 1s, and Si 2p are presented. The spectra indicate the principal core level photoelectron and Auger electron signals with only minor copper and lithium signals and show the expected silicon-carbon and silicon-fluorine species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure.

Haasch, Richard T. (ORCID:0000000194792595)↗
DOE OSTI2022

Calcium Sulfate and Calcium Carbonate Scaling of Thin-Film Composite Polyamide Reverse Osmosis Membranes with Surface-Tethered Polyacrylic Acid Chains

The gypsum and calcite scaling propensities of the thin-film composite polyamide (PA-TFC) reverse osmosis (RO) membrane, modified with a tethered surface layer of polyacrylic acid (PAA) chains, was evaluated and compared to the scaling of selected commercial RO membranes. The tethered PAA layer was synthesized onto a commercial polyamide membrane (i.e., base-PA) via atmospheric pressure plasma-induced graft polymerization (APPIGP). The PAA nano-structured (SNS) base-PA membrane (SNS-PAA-PA) was scaled to a lesser degree, as quantified by a lower permeate flux decline and surface imaging, relative to the tested commercial membranes (Dow SW30, Toray SWRO, and BWRO). The cleaning of gypsum-scaled membranes with D.I. water flushing achieved 100% water permeability recovery for both the SNS-PAA-PA and Dow SW30 membranes, relative to 92–98% permeability restoration for the Toray membranes. The calcium carbonate scaling of SNS-PAA-PA membranes was also lower relative to the commercial membranes, but permeability recovery after D.I. water cleaning was somewhat lower (94%) but consistent with the level of surface scale coverage. In contrast, the calcite and gypsum-scaled membrane areas of the commercial membranes post-cleaning were significantly higher than for the SNS-PAA-PA membrane but with 100% permeability recovery, suggesting the potential for membrane damage when mineral scaling is severe.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The Effects of Lithium Ions and pH on the Function of Polyacrylic Acid Binder for Silicon Anodes

Binder plays a critical role in the performance of silicon anodes for lithium-ion batteries, specifically by connecting particles of active material and promoting adhesion to the current collector. Recent studies have differed on the relative cycle life of silicon anodes made from water-based polyacrylic acid (PAA) vs LiOH-PAA binders. Differences between the two may be due to the pH value or the extra Li + in the binder, both of which change when LiOH is added to PAA. Here we investigate the impact of these two variables on the performance of silicon anodes. Regarding the effect of Li + , cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) results confirm our hypothesis that the extra Li + facilitates ion transport. Regarding pH, we find that high pH in binders is detrimental to the electrode mechanical integrity, as observed in peeling tests and cross-sectional imaging. However, viscosity tests reveal that increased pH benefits the coating and mixing process. Further, our cycling results show that LiOH-PAA binder maintains greater cell capacity than does PAA, and further that LiOH-PAA at pH 4.5 leads to a cell with the highest capacity. Therefore, an intermediate pH is an optimal compromise between benefits observed for the low and high pH experiments.

25 ENERGY STORAGE↗
DOE OSTI2021

Enabling aqueous processing for LiNi 0.80 Co 0.15 Al 0.05 O 2 (NCA)-based lithium-ion battery cathodes using polyacrylic acid

Replacing N-methyl-2-pyrrolidone (NMP) with water in the production of lithium-ion battery cathodes is critical to realizing process cost savings and improved worker safety. LiNi 0.80 Co 0.15 Al 0.05 O 2 (NCA) is a poor fit for aqueous processing due to destructive Al current collector corrosion resulting from highly basic slurries and detrimental surface reconstruction reactions that occur in water. In this study, polyacrylic acid (PAA, MW = 450,000 g·mol -1 ) is examined as a corrosion-mitigating and surface-stabilizing agent. Adding PAA to an aqueous NCA slurry can provide a stable pH (4.0–8.5) for at least 4 h, since the carboxyl groups from PAA dissociate and increase the proton concentration in the slurry. Further, these groups can also adsorb to the surface of NCA particles and provide electrostatic stability from active material particle agglomeration, as revealed by zeta potential measurements. Minor cracking does occur at the electrode surface; this cracking likely caused poorer adhesion to the Al current collector in the aqueous-processed film when compared to the NMP-processed baseline. Electrochemically, the leached Li does cause a lower initial capacity for the aqueous-processed cathode, though the capacity retention of the aqueous-processed cathode is better than the baseline. The cracks in the coating led to a rise in charge transfer resistance that hindered rate capability above 1C.

25 ENERGY STORAGE↗
DOE OSTI2023

Effect of isopropanol cosolvent on the rheology and spinnability of aqueous polyacrylic acid solutions

Abstract We investigate the effect of alcohol fraction (isopropanol, IPA) in a binary water‐alcohol solvent mixture on the shear and extensional rheological properties, as well as the role of viscoelasticity on fiber formation of poly(acrylic acid) (PAA) in electrospinning. Comparison of the scaling of both specific viscosities η sp and extensional relaxation times λ E of PAA in water–IPA mixtures, showed stronger scaling compared to salt‐free aqueous polyelectrolyte solutions, except for the η sp in the unentangled regime displaying a polyelectrolyte‐like scaling η sp ~ c 0.5 for all IPA%. Such deviation suggested IPA induces association/aggregation of PAA. However, the trends between η sp and λ E magnitudes as a function of IPA% differ for concentrations compared in the entangled regime. The η sp as well as their elastic moduli exhibit a maximum, whereas λ E increases monotonically with IPA%, suggesting a complex interplay of various interactions are dictating their structure in water‐IPA mixtures, affecting their shear and extensional response differently. Electrospinning experiments showed increasing IPA% reduces the onset of both beaded and uniform fibers. Analysis using dimensionless numbers indicated the enhancement of their elasticity by IPA, and the consequent stabilizing effect on their jets/filaments against break‐up during electrospinning, plays a role in the improvement of their fiber formation.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Parametric test of a zirconium (4) oxide-polyacrylic acid dual layer hyperfiltration membrane with spacecraft washwater

Performance data consisting of solute rejections and product flux were measured, as dependent on the operation parameters. These parameters and ranges were pressure (500,000 n/m2 to 700,000 n/m2), temperature (74 C to 95 C), velocity (1.6 M/sec to 10 M/sec), and concentration (up to 14x). Tests were carried out on analog washwater. Data presented include rejections of organic materials, ammonia, urea, and an assortment of ions. The membrane used was deposited in situ on a porcelain ceramic substrate.

Brandon, C. A.↗
DOE OSTI2022

Electronic structures on swollen hydrogels

This document describes a conformable substrate that includes a hydrogel having adhesion-promoting moieties, said adhesion-promoting moieties comprising one or more catechol groups. The conformable substrate includes an array of microelectrodes bonded to the hydrogel by the adhesion-promoting moieties via the one or more catechol groups. This document also describes a method for transfer printing of an electronic structure to a hydrogel. The method includes the steps of coating a donor substrate with a film of polyacrylic acid, crosslinking the film of polyacrylic acid in a solution comprising divalent ions, patterning a microelectrode array onto the crosslinked film of polyacrylic acid, laminating an adhesive hydrogel substrate onto the donor substrate coated by the crosslinked film of polyacrylic acid comprising the patterned microelectrode array, and separating the crosslinked film of polyacrylic acid from the donor substrate in a monovalent solution.

Bettinger, Christopher J.↗
DOE OSTI2023

Understanding of three different polyvinylpyrrolidone (PVP) based battery binders blends on graphene surfaces from first principles via DFT simulations

Binders play a crucial role in binding electrodes, current collectors, and conductive agents during battery manufacturing. The selection of the binders and their blends considerably affect various properties such as mechanical durability, adhesion performance, ionic/electronic conductivities, and solid electrolyte interface stability for lithium-ion batteries. In this work, polyvinylidene di-fluoride (PVDF), polyacrylic acid (PAA), polyvinylpyrrolidone (PVP), and lithiated polyacrylic acid (Li-PAA) were selected as the model binders, and their blends were studied on graphene surfaces. Further, among them, PVDF is hardly soluble in water unlike the other binders, so in practice, the blend of PVP:PVDF is not thought to be a proper combination. However, the PVP:PVDF binder has also been included because the purpose of this work is to calculate several electronic properties such as binding energies, intermolecular interaction energies, bond critical points, electron density, and the Laplacian of electron density at critical bonding regions of all these blends at the molecular level via density functional theory (DFT) simulations in order to evaluate and compare how is the interaction strength and bonding type of three different lithium-ion batteries (LIBs) binder blends on graphene surfaces. Most stable binder pairs and their binding mechanisms on graphene surfaces were studied. The delocalization of lithium in Li-PAA was studied with the presence of water.

25 ENERGY STORAGE↗
NASA NTRS1984

Kinetics of chromium ion absorption by cross-linked polyacrylate films

Three cross-linked ion exchange membranes were studied as to their ability to absorb chromium ion from aqueous chromium III nitrate solutions. Attention was given to the mechanism of absorption, composition of the absorbed product, and the chemical bonding. The membranes were: calcium polyacrylate, polyacrylic acid, and a copolymer of acrylic acid and vinyl alcohol. For the calcium polyacrylate and the copolymer, parabolic kinetics were observed, indicating the formation of a chromium polyacrylate phase as a coating on the membrane. The rate of absorption is controlled by the diffusion of the chromium ion through this coating. The product formed in the copolymer involves the formation of a coordination complex of a chromium ion with 6 carboxylic acid groups from the same molecule. The absorption of the chromium ion by the polyacrylic acid membranes appears to be more complicated, involving cross-linking. This is due to the coordination of the chromium ion with carboxylic acid groups from more than one polymer molecule. The absorption rate of the chromium ion by the calcium salt membrane was found to be more rapid than that by the free polyacrylic acid membrane.

May, C. E.↗
NASA NTRS1984

Binder for Carbon-Fiber Coating

Insoluble, even coating formed by soaking in polyacrylic acid. Carbon fiber material prepared by soaking in solution of 20 percent polyacrylic acid in water. Material blotted and dried at 120 degrees C for at least 2 hours. Dried material reacted with boiling aqueous solution of calcium acetate. Treated material removed from boiling solution, blotted, dried at 120 degrees C, washed with distilled water, and dried again.

Dowler, W. L.↗