Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polypropylene (PP) fiber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Optimization of matrix viscosity improves polypropylene fiber dispersion and properties of engineered cementitious composites

Engineered cementitious composites (ECC) is a durable cementitious material with high tensile ductility and strain-hardening characteristics. Although considered as a cost-effective fiber for ECC, polypropylene (PP) fiber is reportedly difficult to disperse in mortar matrix due to its high aspect ratio and hydrophobicity. In this study, the matrix viscosity of a low-carbon ECC based on limestone calcined clay cement was tailored as a variable to improve PP fiber dispersion under a pre-determined mixing protocol. The effect of matrix viscosity on the composite fresh and hardened properties was investigated experimentally. Results suggested an optimal range of matrix viscosity (10.3–11.5 Pa . s) favors the composite tensile strength and strain capacity at 28 days. At the optimal state with a 0.1 % viscosity modifying admixture (VMA)-to-binder mass ratio, PP-ECC achieved 7.0 % tensile strain capacity and 3.5 MPa ultimate tensile strength. When matrix viscosity falls outside the desired range, both ultimate tensile strength and strain capacity were diminished. By tailoring the VMA dosage, the matrix viscosity can be adjusted for desired fiber dispersion, workability, and mechanical properties. Finally, the findings of this study provide a technical reference for the practical design and application of PP-ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of fiber sizing and glass fiber laminate hybridization on vibration damping and mechanical properties of banana fiber reinforced polypropylene composites

Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.

Banana fiber↗
DOE OSTI2021

Performance of hybridized bamboo-carbon fiber reinforced polypropylene composites processed using wet laid technique

The end-of-life vehicles (ELV) regulations motivate hybrid materials usage in automotive industries to optimize properties at reduced cost and increase eco-friendly designs. This research explores hybrid compositions of natural bamboo fiber and synthetic carbon fiber. The goal of hybridization was to synergistically benefit from each constituent– i.e., sustainability, energy absorption and superior damping from bamboo, and high strength and stiffness from carbon fiber. Carbon fibers (CF), bamboo fibers (BF) and polypropylene (PP) fibers were dispersed in water to produce wet-laid hybrid mats. The mats were compression molded into consolidated panels to obtain the hybrid composite(s) (BF-CF-PP). Four formulations with different fiber-resin weight percent were designed and produced including- BF-PP (30/70), BF-PP (50/50), BF-CF-PP (32/8/60), and BF-CF-PP (8/32/60). The effect of (a) fiber length, (b) surface treatment, (c) fiber content, and (d) consolidation pressure on the mechanical properties were examined. The improved mechanical (flexural strength 76.4 MPa, flexural modulus 4.1 GPa, ILSS 12.4 MPa and impact strength 49.9 KJ/m 2 ) and vibrational damping (1.05%) properties showed that the BF-CF-PP (8/32/60) provided higher properties compared to the other variants. The projected properties at various stoichiometric ratios of carbon and bamboo fiber revealed that the properties of hybrid composites could be tailored to produce desirable, cost-effective, and sustainable automotive components.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of spatial distribution of polymer fibers on preventing spalling of UHPC at high temperatures

Polypropylene (PP) fibers are commonly used for the prevention of thermal spalling of ultra-high performance concrete (UHPC). In this work, the effect of fiber distribution on permeability and spalling resistance is investigated and an analytical model for permeability at 150 °C is proposed. This model, considering the parameters like fiber dimensions, dosage, and percolation, is based on Kozeny-Carman equation. It was found that the percolation of the interconnecting fiber network resulted in a significant increase in permeability of UHPC. X-ray tomography data on the three-dimensional spatial distribution of fibers reiterated that fiber aspect ratio and dosage (and fiber number density) were critical in increasing the fiber connectivity (percolation). It was also found that a vapor permeability of larger than 0.6 × 10{sup −16} m{sup 2} at 150 °C could eliminate spalling. Further, based on a semi-empirical approach, aspect ratio between 300 and 600 was recommended for spalling prevention with a fiber dosage of 0.3–0.4 vol%.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical and self-healing behavior of low carbon engineered cementitious composites reinforced with PP-fibers

While the ultrahigh tensile ductility and superior durability of Engineered Cementitious Composites (ECC) have been demonstrated, the relatively high energy and carbon intensity, as well as high material cost present potential impediments to broader ECC applications. The objective of this research is to develop a more sustainable and cost-effective ECC. The ordinary Portland cement (OPC) and the commonly used PVA fiber in conventional ECC were replaced by limestone calcined clay cement (LC3) and polypropylene (PP) fiber, respectively. The ECC compressive strength, tensile stress-strain relationship, and microcrack self-healing behavior were studied at three water to binder ratios (0.3, 0.2, 0.16). The novel LC3-PP-ECC showed a tensile strain capacity of greater than 6% and an intrinsically tight crack width below 82 μm when loaded to 1% tensile strain. Further, the LC3-PP-ECC demonstrated efficient recovery of the composite tensile ductility and ultimate tensile strength through self-healing. Compared to typical ECC made with OPC and PVA fiber, the material cost, embodied energy and carbon footprint of LC3-PP-ECC are reduced by 61%, 45%, and 48%, respectively. Here, the superior mechanical properties and durability combined with the low environmental impact and cost for material production promote LC3-PP-ECC as a sustainable material for structural and non-structural applications.

42 ENGINEERING↗
DOE OSTI2024

Life cycle assessment of coir fiber-reinforced composites for automotive applications

Past decades have seen an increasing prevalence of natural fiber-reinforced composites (NFRCs) due to growing conscientiousness around sustainability and a push towards vehicle lightweighting. The environmentally friendly and sustainable claims of NFRCs need to be validated due to their large variability and variety, particularly where material substitutions are concerned, such as in substituting glass fiber with natural fiber. Additionally, the objective of this work is to determine the cumulative energy demand (CED) and greenhouse gas emissions (GHG) associated with an automotive part (of volume 0.001 m3) made from 40 wt% coir fiber-reinforced polypropylene (PP) and compared with a similar part made from 40 wt% glass fiber reinforced PP. SimaPro v. 9.0.0.49 was used for the analysis, whereas inventory data were collected from databases, such as Ecoinvent 3, Transportation Energy Databook, Greet model 2022, and published papers. The results showed that CED and GHG associated with the coir fiber-reinforced composite part were lower than the glass fiber-reinforced composite part for both cradle-to-gate (~34–40%) and cradle-to-grave (excluding end-of-life) (~24%) analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crack width control and mechanical properties of low carbon engineered cementitious composites (ECC)

Engineered Cementitious Composites (ECC) have superior properties with high tensile ductility and tight crack width compared to conventional concrete. The properties of ECC are significantly influenced by the material composition which can be tailored to enhance the sustainability of ECC. Towards this goal, recycled crumb rubber (CR) and silica fume (SF) were used to tailor the properties of a polypropylene-fiber reinforced ECC with a low carbon binder based on limestone calcined clay cement (LC3) in this study. Crumb rubber was found to be effective in enhancing strain-hardening performance and reducing the width of the multiple microcracks. However, a loss of compressive strength was accompanied by an increasing amount of CR. While silica fume or lower w/b ratio enhanced the compressive strength, the crack width of ECC increased at higher SF content or lower w/b. The underlying mechanisms of these trends were traced to the alteration of the matrix fracture toughness and fiber/matrix interfacial bond. Rubber particle bridging was found to contribute to crack width control. Finally, the combined use of the LC3 green binder and CR led to a lowering of the embodied and operational carbon footprint of ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)

Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of textile-grade carbon fiber polypropylene composites

In this work, we consider low-cost carbon fiber produced with a textile-grade precursor. The objective of the study is to investigate textile-grade carbon-fiber-reinforced-polypropylene composites (TCF-PP) from compounded pellets for mechanical and thermal characterization. Four sets of pellets with 1%, 5%, 10%, and 15% reinforcement were manufactured using textile-grade carbon fiber (TCF) and polypropylene (PP) by twin-screw compounding. The addition of TCFs through gravimetric feeder directly in the extruder resulted in lower fiber content; however, side feeder has shown good potential. The pellets were further processed in extrusion compression molding to manufacture plaques. An increase in fiber loading has a negligible effect on fiber attrition as fiber length distribution variation between 1% and 15% reinforced pellets was very small. The addition of TCFs in PP showed a significant improvement in mechanical properties. The tensile strength and modulus of the composite were 26% and 161%, respectively, improved by the addition of 10 wt% TCF. Similar results were observed in the flexure test. However, the impact properties were reduced by 25.54% by the addition of 15% TCF.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Long coir and glass fiber reinforced polypropylene hybrid composites prepared via wet-laid technique

Natural fiber composites offer an advantage in terms of weight saving for many automotive applications; however, many natural fiber composites lack properties to justify substitution for synthetic composites. Hybridizing the natural fiber composites by adding a fraction of synthetic fibers is an innovative approach to provide a balance between composite's performance and weight savings. In this study, coir fiber (40 wt%)-reinforced polypropylene (PP) composites were hybridized by substituting a fraction of coir fiber with glass fiber (0–30 wt%). The composites were prepared using a novel wet-laid technique followed by compression molding, where the fiber length is preserved. The composites prepared by hybridizing PP/coir fibers with glass fibers were light in weight (6–20% lighter compared to 40 wt% glass fiber reinforced PP) with significantly enhanced tensile (strength – 49–182%, modulus – 54–130%), flexural (strength – 41–104%, modulus – 64–193%), and impact properties (157 - 474%) compared to 40 wt% coir fiber reinforced PP composites. Furthermore, the addition of glass fiber (10–30 wt%) to coir fiber reduced the water-absorbing tendency (by 18–74%) of PP/coir fiber composites. All in all, this work has potential applications in automotive, mass transit, and truck applications where natural fiber composites are being investigated as alternatives to metal and/or fully synthetic composites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Cradle-to-gate life cycle assessment of advanced composite panels incorporating CO 2 -derived multi-walled carbon nanotubes and hemp fiber for sustainable building applications

Advanced composite panels represent a promising pathway to reducing carbon emissions in the construction industry, yet comprehensive environmental impact assessments remain limited. Here, in this study, we conduct a life cycle assessment (LCA) to evaluate the environmental impacts of innovative composite panels produced from multi-walled carbon nanotubes (MWCNTs), hemp fiber (HF), recycled carbon fiber (rCF), and recycled polypropylene (PP), exploring their potential as baseline structural equivalents to conventional gypsum board. MWCNTs and HF play a critical role in sequestering carbon during raw material production, while the recycling processes for CF and PP generally require less energy compared to virgin material production. The LCA evaluates environmental performance using the TRACI 2.1 method, covering global warming potential (GWP), ozone depletion, smog formation, acidification, eutrophication, carcinogenic and non-carcinogenic effects, respiratory impacts, ecotoxicity, and fossil fuel depletion. Compositional variations—resin type (virgin vs. recycled), rCF content (9–29 wt%), and HF content (10–30 wt%)—are introduced for sensitivity and hotspot analyses. Results demonstrate that, when compared on the basis of preliminary structural equivalence, increasing recycled PP, rCF, and HF content can significantly reduce global warming potential compared to gypsum board. Beyond carbon reduction, the composite panels show trade-offs across other environmental categories. With the growing demand for composite materials in interior panels, ceiling systems, and exterior claddings, these findings highlight the environmental benefits and potential trade-offs of the proposed composites, establishing a foundational framework to support their continued development toward full building-system integration.

Advanced composite manufacturing↗
DOE OSTI2025

Polypropylene Composites Reinforced With Recycled Waste Cellulosic Fiber/Fine Mixture: The Impact of Cellulose Sieving on Performance

This study explores how a sieving step of waste cellulosic fiber and fine (WCFF) mixture affects the performance of WCFF‐loaded polypropylene (PP) composites and whether the separation of fines from fibers offers an added benefit. The WCFF samples were downsized, and four different filler size ranges were sieved using a series of mesh sizes from 4 to 0.85 mm. The WCFF/PP composites were then compounded at 20 wt.% loading of WCFF using a twin‐screw extruder. Incorporating WCFF increased the tensile strength to 41.28 MPa and the modulus to 3207 MPa, accounting for 28% and 38% enhancements, respectively. Interestingly, the greatest improvements were associated with the nonsieved WCFF case, and the sieved WCFF fibers provided only marginal enhancements over virgin PP. The outperformance of nonsieved WCFF was attributed to the synergistic reinforcement of hybrid fibers and fines as well as the maintenance of longer fibers in the system. However, the strain at break and impact strength of PP decreased after introducing WCFF. Moreover, the complex viscosity and storage modulus increased with an increase in the filler size, due to the formation of a more effective percolative network. The PP's crystallinity exhibited a relatively strong dependency on the sieving, where WCFF samples with short‐aspect‐ratio fillers promoted the crystallinity significantly. It was also found that the WCFF degradation onset temperature increased once it was incorporated into PP. This study suggests that waste cellulosic feedstocks can be utilized as a reinforcement without additional sieving to manufacture high‐performance and cost‐effective composites.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sizing of discontinuous natural fibers: Effect of sizing approach and sizing concentration on composite properties

Natural fiber reinforced composites (NFRCs) are gaining attention in automotive applications as an alternative to glass fiber composites due to their lightweight and renewable sourcing. However, the inherent hydrophilicity of natural fibers leads to poor compatibility with hydrophobic polymers which adversely affects the mechanical properties of the composites and can limit their application to non-structural parts. Sizing is a common approach used for synthetic fibers to improve the interface between fiber and matrix. However, there is limited study on the sizing of natural fibers, and hence the focus of this work. Here, in this study, two different approaches to sizing discontinuous coir fibers were investigated, namely; (1) ex-situ sizing and (2) in-situ sizing. A commercial polypropylene (PP) based sizing agent was used and the effects of varying sizing solution concentrations (1.5, 2.5, and 3.5 wt%) on the properties of the composites was studied. Results showed that composites prepared via the in-situ sizing process had better fiber–matrix adhesion and improved tensile properties compared to ex-situ sized composites. On studying the effect of different sizing concentrations on composite properties, we found that the tensile strength of the composites increased (by ∼ 42 %) up to 2.5 wt% sizing concentration (in solution) and then decreased. However, the impact strength decreased significantly on increasing the sizing content beyond 1.5 wt% (by ∼ 40 %). Additionally, the study was further extended to investigate the effect of sizing on different NFRCs (coir, banana, and cottonized hemp fiber) where effectiveness of sizing was found to be influenced by the fiber surface morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2023

New Sesame Equations of State for Polypropylene, Polyvinylchloride (PVC), and Nylon 66

I built new Sesame equations of state (EOS) for polypropylene (PP), polyvinylchloride (PVC), and nylon 66. PP has the same stoichiometry as polyethylene and TPX but with a density intermediate between the two. Nylon is a polyamide manufactured chiefly in the form of fibers. PP and PVC are the second- and third-most widely produced polymers in the world. All three are thermoplastics. Their monomer units are depicted in Figure 1. I discuss the theory on which the EOS are based in the following section, then compare results to thermal and shock compression data in Section III.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding the Elastic, Plastic, and Damage Features in Fracturing of Self-reinforced Thermoplastic Composites via Non-destructive Digital Imaging Correlation

This work demonstrated the utilization of non-destructive Digital Imaging Correlation (DIC) method to characterize the elastic, plastic, and damage features during the Mode I intra-laminar fracturing process of self-reinforced thermoplastic composites by using a self-reinforced polypropylene (PP) composite as an example. The DIC results clearly showed the development of huge plastic zone (PZ) and non-negligible Fracture Process Zone (FPZ) in front of the notch tip during the fracturing process, and the geometries and sizes of the foregoing zones at the peak load were further quantified. Such an interesting fracturing behavior of self-reinforced thermoplastic composites is way different from brittle materials (e.g., glass, acrylic, etc.), ductile materials (e.g., aluminum, steel, etc.), and even quasi-brittle materials (e.g., concrete, nanoparticle-reinforced composites, tough ceramics, wood, cement, carbon/glass fiber-reinforced polymers, etc.). Thus, understanding the elastic, plastic, and damage features is the first step before better characterizing the material fracture properties of self-reinforced thermoplastic composites through new analytical methods and computational modeling. These efforts are of utmost importance for wide applications of self-reinforced thermoplastic composites in various engineering fields in the future.

Lightweight Composites, Self-reinforced Thermoplas↗
DOE OSTI2023

Recycled Glass Polypropylene Composites from Transportation Manufacturing Waste

In recent years there has been growing interest in developing recycling technologies for composites manufacturing scrap, process waste and end-of-life parts. The focus of this work was to establish processing routes and mechanical property bounds for glass-polypropylene (PP-GF) scrap from the production of parts for truck trailers, automobiles, and rail cars. This study considered PP-GF scrap and demonstrated extrusion-compression molding (ECM) as a viable route for the closed-loop manufacture of composite parts. The results were promising in terms of the strength and modulus retention of the PP-GF recyclate. The tensile strength and modulus was the highest for 50% and 66% recycled content, compared with 100% and 83% recycle content. The flexural strength and modulus of the 100% and 83% recycled compositions was higher than the 66% and 50% recycled content, respectively. The impact energy absorption of the PP-GF recyclate at at all fiber loadings was superior in absorbing energy compared with the incumbent (benchmark) plywood. This work is useful to designers seeking to incorporate recycled materials in their products.

Vaidya, Uday↗