Search NASA⌕ Search

SEARCH · Search NASA

Results for “Potassium Carbonate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Abiotic synthesis of fatty acids

The formation of fatty acids by Fischer-Tropsch-type synthesis was investigated with ferric oxide, ammonium carbonate, potassium carbonate, powdered Pueblito de Allende carbonaceous chondrite, and filings from the Canyon Diablo meteorite used as catalysts. Products were separated and identified by gas chromatography and mass spectrometry. Iron oxide, Pueblito de Allende chondrite, and Canyon Diablo filings in an oxidized catalyst form yielded no fatty acids. Canyon Diablo filings heated overnight at 500 C while undergoing slow purging by deuterium produced fatty acids only when potassium carbonate was admixed; potassium carbonate alone also produced these compounds. The active catalytic combinations gave relatively high yields of aliphatic and aromatic hydrocarbons; substantial amounts of n-alkenes were almost invariably observed when fatty acids were produced; the latter were in the range C6 to C18, with maximum yield in C9 or 10.

Leach, W. W.↗

Development of a prototype regenerable carbon dioxide absorber for portable life support systems

The design and development of a prototype carbon dioxide absorber using potassium carbonate (K2CO3) is described. Absorbers are constructed of thin, porous sheets of supported K2CO3 that are spirally wound to form a cylindrical reactor. Axial gas passages are formed between the porous sheets by corrugated screen material. Carbon dioxide and water in an enclosed life support system atmosphere react with potassium carbonate to form potassium bicarbonate. The potassium carbonate is regenerated by heating the potassium bicarbonate to 150 C at ambient pressure. The extravehicular mission design conditions are for one man for 8 h. Results are shown for a subunit test module investigating the effects of heat release, length-to-diameter ratio, and active cooling upon performance. The most important effect upon carbon dioxide removal is the temperature of the potassium carbonate.

Onischak, M.↗

Development of a prototype regenerable carbon dioxide absorber

Design information was obtained for a new, regenerable carbon dioxide control system for extravehicular activity life support systems. Solid potassium carbonate was supported in a thin porous sheet form and fabricated into carbon dioxide absorber units. Carbon dioxide and water in the life support system atmosphere react with the potassium carbonate and form potassium bicarbonate. The bicarbonate easily reverts to the carbonate by heating to 150 deg C. The methods of effectively packing the sorbent material into EVA-sized units and the effects of inlet concentrations, flowrate, and temperature upon performance were investigated. The cycle life of the sorbent upon the repeated thermal regenerations was demonstrated through 90 cycles.

Onischak, M.↗

Silver oxide sorbent for carbon dioxide

Material can be regenerated at least 20 times by heating at 250 C. Sorbent is compatible with environment of high humidity; up to 20% by weight of carbon dioxide can be absorbed. Material is prepared from silver carbonate, potassium hydroxide or carbonate, and sodium silicate.

Colombo, G. V.↗

A comparative TEA of a two-step process using chemical solvents for producing an ultra-sweet natural gas

Here, a comprehensive Techno-Economic Analysis (TEA) was performed to evaluate the economic feasibility of a novel two-step process (TSP) developed in Aspen Plus V12.1 to desulfurize and decarbonize a raw natural gas containing (2 mol% H 2 S and 5 mol% CO 2 ) into an ultra-sweet natural gas containing (1.72 ppmv H 2 S and 4.19 ppmv CO 2 ). The raw natural gas flow rate used in the TSP was 117.74 kg/s at 60 °C and 50 bar. The TSP combines an H 2 S desulfurization step using potassium carbonate (K 2 CO 3 ) and a CO 2 capture step using 3 different chemical solvents, monoethanolamine (MEA), sodium glycinate (SGS), and potassium glycinate (PGS). Both steps employ fixed-bed absorbers packed with Mellapak 250Y structured packing. The hydraulics and mass transfer characteristics for the TSP were calculated, indicating normal operation with higher gas-side (k G ) than liquid-side (k L ) mass transfer coefficients. The TEA of TSP indicated that PGS had the most promising economic feasibility among the 3 solvents as it exhibited the lowest Levelized Cost of CO 2 capture (LCOC) of $\$$47.54/ton.CO 2 at a Capital Expenditure (CAPEX) of $\$$24.98 million, and an Operating Expenditure (OPEX) of $\$$12.20 million/year. Also, the TSP could produce one MMSCF of ultra-sweet natural gas at a total cost of $\$$339.55.

03 NATURAL GAS↗

Replication of the Apparent Excess Heat Effect in a Light Water-Potassium Carbonate-Nickel Electrolytic Cell

Replication of experiments claiming to demonstrate excess heat production in light water-Ni-K2CO3 electrolytic cells was found to produce an apparent excess heat of 11 W maximum, for 60 W electrical power into the cell. Power gains range from 1.06 to 1.68. The cell was operated at four different dc current levels plus one pulsed current run at 1 Hz, 10% duty cycle. The 28 liter cell used in these verification tests was on loan from a private corporation whose own tests with similar cells are documented to produce 50 W steady excess heat for a continuous period exceeding hundreds of days. The apparent excess heat can not be readily explained either in terms of nonlinearity of the cell's thermal conductance at a low temperature differential or by thermoelectric heat pumping. However, the present data do admit efficient recombination of dissolved hydrogen-oxygen as an ordinary explanation. Calorimetry methods and heat balance calculations for the verification tests are described. Considering the large magnitude of benefit if this effect is found to be a genuine new energy source, a more thorough investigation of evolved heat in the nickel-hydrogen system in both electrolytic and gaseous loading cells remains warranted.

Niedra, Janis M.↗

Upcycling Polyethylene Waste into Hybrid Graphitic Porous Carbon Materials Used in High‐Performance Zinc‐Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, mixtures of PE wastes into a hybrid graphitic porous carbon (HGPC) by a thermal oxidation pretreatment step, with assistance of an inert solid additive (KCl), to functionalize, crosslink, and stabilize the PE waste followed by carbonization and catalytic graphitization steps with a potassium carbonate catalyst, are upcycled. The PE waste‐derived HGPC (PW‐HGPC) has a hybrid structure composed of graphene‐like carbon nanosheets grown on the surface of carbon particles, high porosity with specific surface area, up to 1,763 m 2 g −1 , and good graphitic degree with average Raman I 2D / I G ratios of 0.53. When used as cathode material for zinc‐ion hybrid capacitors, this PW‐HGPC exhibits an excellent specific capacity, up to 126.7 mAh g −1 , at high mass loading of 10 mg cm −2 . Moreover, PW‐HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10 000 cycles. Additionally, the KCl is recycled and reused over five times. This method provides a new solution for upcycling PE wastes into high value‐added carbon materials, not only for zinc‐ion hybrid capacitors but also for other electrochemical energy storage device applications.

hybrid graphitic porous carbon↗

Environmental carbon dioxide control

A study of environmental carbon dioxide control for NASA EVA missions found solid potassium carbonate to be an effective regenerable absorbent in maintaining low carbon dioxide levels. The supported sorbent was capable of repeated regeneration below 150 C without appreciable degradation. Optimum structures in the form of thin pliable sheets of carbonate, inert support and binder were developed. Interpretation of a new solid-gas pore closing model helped predict the optimum sorbent and analysis of individual sorbent sheet performance in a thin rectangular channel sorber can predict packed bed performance.

Onischak, M.↗

Electro-carburization of mild steel through two-step reaction in molten-salt electrolyte

The rapid carburization of mild steel is demonstrated via the electrochemical deposition of solid carbon, followed by thermochemical iron-carbon (Fe-C) reaction using a molten lithium-potassium carbonate (LiKCO 3 ) salt electrolyte and carbon dioxide as the carbon source. Depth-dependent microstructural and compositional changes in the steel are shown to be controlled by the applied cell voltage and reaction temperatures. Reaction temperatures above the Fe-C eutectoid temperature promote faster carburization due to carbon dissolution into austenite. The carbon deposition rate is regulated by the applied cell voltage: At - 2.4 V, carbon deposition occurs much faster than its diffusion into the steel, resulting in the accumulation of a carbon-rich layer exceeding 1 mm, which does not diffuse into the steel. In contrast, at - 1.8 V, all deposited carbon effectively diffuses into the steel, leaving a minimal external deposit. In both cases, carbon ingress forms a carbide-rich surface layer and precipitates additional carbides along the grain boundaries within the steel electrode. This method offers a potential approach to increase the carbon content of mild or low-carbon steel feedstocks, such as scrap or direct reduced iron, for industrial applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Upcycling Polyethylene Waste Into Hybrid Graphitic Porous Carbon Materials Used in High-Performance Zinc-Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, we report a chemical process that addresses this challenge by converting mixtures of linear low-density polyethylene (LLDPE), low-density polyethylene (LDPE), and high-density polyethylene (HDPE) waste into a hybrid graphitic porous carbon (HGPC) that can be used as a zinc-ion hybrid capacitor cathode. The process uses a low temperature thermal oxidation pre-treatment step, with assistance of an inert solid additive (KCl) to increase the effective surface area of the PE melt, to functionalize, cross-link, and stabilize the PE waste followed by carbonization and catalytic graphitization steps at higher temperatures with a potassium carbonate (K2CO3) catalyst. The PE waste derived HPGC (PW-HPGC) has a hybrid structure composed of graphene-like carbon nanosheets grown on the surface of carbon particles, high porosity with the Brunauer–Emmett–Teller (BET) specific surface area up to 1,763 m2g-1, and good graphitic degree with average Raman I2D/IG ratios of 0.53. When used as a cathode material for zinc-ion hybrid capacitors, this PW-HGPC exhibits an excellent specific capacity up to 126.7 mAhg-1 at high mass loading of 10 mgcm-2. Moreover, PW-HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10,000 cycles at a current density of 2.0 A g-1.

hybrid graphitic porous carbon↗

Polyimides Containing Carbonyl and Ether Connecting Groups

Semicrystallinity gives rise to tough, solvent-resistant polymers. New polyimides prepared from reaction of aromatic dianhydrides with new diamines containing carbonyl and ether connecting groups between aromatic rings. Damines prepared from reaction of 4-aminophenol with activated aromatic difluoro compounds in presence of potassium carbonate. These types of polymers have potential applications in molded products, films, adhesives, and composites.

Hergenrother, Paul M.↗

Polyimidazoles via aromatic nucleophilic displacement

Polyimidazoles (PI) are prepared by the aromatic nucleophilic displacement reaction of di(hydroxyphenyl) imidazole monomers with activated aromatic dihalides or activated aromatic dinitro compounds. The reactions are carried out in polar aprotic solvents such as N,N-dimethyl acetamide, sulfolane, N-methylpyrrolidinone, dimethylsulfoxide, or diphenylsulfone using alkali metal bases such as potassium carbonate at elevated temperatures under nitrogen. The di(hydroxyphenyl) imidazole monomers are prepared by reacting an aromatic aldehyde with a dimethoxybenzil or by reacting an aromatic dialdehyde with a methoxybenzil in the presence of ammonium acetate. The di(methoxyphenyl) imidazole is subsequently treated with aqueous hydrobromic acid to give the di(hydroxphenyl) imidazole monomer. This synthetic route has provided high molecular weight PI of new chemical structure, is economically and synthetically more favorable than other routes, and allows for facile chemical structure variation due to the availability of a large variety of activated aromatic dihalides and dinitro compounds.

Connell, John W.↗

Poly(1,3,4-oxadiazoles) via aromatic nucleophilic displacement

Poly(1,3,4-oxadiazoles) (POX) are prepared by the aromatic nucleophilic displacement reaction of di(hydroxyphenyl) 1,3,4-oxadiazole monomers with activated aromatic dihalides or activated aromatic dinitro compounds. The polymerizations are carried out in polar aprotic solvents such as sulfolane or diphenylsulfone using alkali metal bases such as potassium carbonate at elevated temperatures under nitrogen. The di(hydroxyphenyl) 1,3,4-oxadiazole monomers are synthesized by reacting 4-hydroxybenzoic hydrazide with phenyl 4-hydrobenzoate in the melt and also by reacting aromatic dihydrazides with two moles of phenyl 4-hydroxybenzoate in the melt. This synthetic route has provided high molecular weight POX of new chemical structure, is economically and synthetically more favorable than other routes, and allows for facile chemical structure variation due to the large variety of activated aromatic dihalides which are available.

Connell, John W.↗

Chemistry and properties of poly(arylene ether benzoxazole)s

Several new poly(arylene ether benzoxazole)s (PAEBs) were prepared by the nucleophilic displacement reaction of activated aromatic difluorides with two novel bis(hydroxyphenyl benzoxazole), using potassium carbonate. The 6F-containing PAEBs exhibited better solubility and higher Tgs than did the 6,6'-bis-(2-(4-hydroxyphenyl)benzoxazole)-derived polymers. Several of the 6,6'bis(2-(4-hydroxyphenyl)benzoxazole)-derived polymers exhibited crystallinity by DSC and wide-angle X-ray diffraction. Unorientated thin film properties of the 6F-containing PAEBs were comparable to those of other 6F-containing PAEBS that were previously reported. The chemistry and the physical and mechanical properties of the above polymers are discussed.

Smith, J. G., Jr.↗

Chemistry and adhesive properties of poly(arylene ether)s containing heterocyclic units

Novel poly(arylene ether)s containing heterocyclic units were prepared, characterized, and evaluated as adhesives and composite matrices. The polymers were prepared by reacting a heterocyclic bisphenol with an activated aromatic dihalide in a polar aprotic solvent, using potassium carbonate. The polymerizations were generally carried out in N,N-dimethylacetamide at 155 C. In some cases, where the polymers were semicrystalline, higher temperatures and thus higher boiling solvents were necessary to keep the polymers in solution. Heterocyclic rings incorporated into the poly(arylene ether) backbone include phenylquinoxaline, phenylimidazole, benzimidazole, benzoxazole, 1,3,4-oxadiazole, and 1,2,4-triazole. The polymers were characterized by differential scanning calorimetry, solution viscosity, X-ray diffraction, thin film, and adhesive and (in some cases) composite properties. The glass transition temperatures, crystalline melt temperature, solubility, and mechanical properties varied depending upon the heterocyclic ring. The chemistry and properties of these materials are discussed.

Connell, John W.↗

Polybenzimidazoles Via Aromatic Nucleophilic Displacement

Soluble polybenzimidazoles (PBI's) synthesized by nucleophilic displacement reaction of di(hydroxyphenyl)-benzimidazole monomers with activated aromatic difluoride compounds in presence of anhydrous potassium carbonate. These polymers exhibit good thermal, thermo-oxidative, and chemical stability, and high mechanical properties. Using benzimidazole monomers, more economical, and new PBI's processed more easily than commercial PBI, without loss of desirable physical properties.

Connell, John W.↗