SEARCH · Search NASA

Results for “Power-law creep”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

7 records

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Residual elastic strain evolution due to thermal cycling of a ceramic-metal composite (WC-Cu) via high energy X-ray diffraction and analytical modeling

Residual stress, when superimposed with in-service loading, can significantly reduce the lifetime and performance of a component. Ceramic-metal composites are susceptible to residual stresses due to the thermal expansion mismatch of the ceramic and metallic phases. The WC-Cu composite explored in the present study provides a promising combination of thermal conductivity and strength properties, while exhibiting counterintuitive improvements in strength and ductility after thermal cycling. Further, this work quantifies the evolution of the residual elastic strains as a result of processing and cyclic thermal loading in a co-continuous WC-Cu composite through experimental high energy X-ray diffraction and kinetics-based modeling. Both analyses indicate that processing-induced residual tensile stress in the copper phase is relieved upon subsequent thermal cycling, with kinetics modeling revealing the cyclic-dependent nature of the active power-law creep mechanisms. The results indicate that, through stress relaxation, this material system maintains structural stability during thermal cycling. The illustrated kinetics of relaxation can inform general material processors and designers of ceramic-metal composites to minimize detrimental residual stress and improve performance of these material systems.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effects of time-dependent deformation of shale on the integrity of a geological nuclear waste repository

Safety assessment of geological nuclear waste repositories is essential for the permanent disposal of spent nuclear fuels and high-level radioactive waste. The long-term integrity of the host rock as well as the engineered barrier system (e.g., bentonite buffer) surrounding nuclear waste canisters is of particular importance as decay heat from nuclear waste canisters, which will last over thousands of years, significantly disturbs the thermo-hydromechanical (THM) state of the repository. In this study, THM coupled simulations were carried out to investigate the effect of time-dependent deformation (i.e., creep) of shale on the long-term integrity of a generic subsurface nuclear waste repository. The Norton-Bailey creep model, which is also known as the Lemaitre-Menzel-Schreiner model, was employed to simulate the power-law type creep that is observed in shales. The TOUGH-FLAC simulator was employed for the THM coupled modeling of the repository. The objective of this study is to assess the effect of creep in different shales (i.e., high creep shale vs. low creep shale) on long-term stress and permeability changes in the repository. Results show potential advantages of constructing repositories in the high creep shale, as deviatoric stress levels in the formation decreased to zero in 100 years since the emplacement of nuclear waste canisters and the permeability also decreased to the undamaged, intrinsic levels in 10,000 years. Also, mean effective stress levels in the bentonite buffer increased by 100% in the high creep shale case relative to the low creep shale case at 10,000 years due to creep-induced contraction of the nuclear waste disposal tunnel. However, in earlier periods (e.g., 1000 years), the stress levels in the bentonite buffer were twice smaller in the high creep shale case than in the low creep shale case, which shows a tradeoff between the intermediate- (~1000 years) and long-term (>10,000 years) compaction levels in the bentonite buffer depending on the creep characteristics of the host shale.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

An accelerated framework for predicting creep rupture lifetimes in engineering alloys

Confidently predicting high-temperature deformation, including creep and creep rupture, is paramount for the design and commercialization of candidate materials for advanced nuclear energy systems. To accelerate creep quantification, we introduce a framework that enables rapid, cost-effective, and reliable prediction of creep rupture lifetimes, minimizing reliance on time-intensive bulk creep testing. Unlike conventional creep analysis, which requires extensive time and resources, our method leverages a maximum of four short-term bulk creep tests as training data for prediction. This framework combines high-throughput nanoindentation up to 700 °C with these targeted bulk tests to inform our creep rupture model in order to predict rupture lifetimes. The strong agreement between our predictions and conventional experimental data demonstrates the effectiveness of our approach for accelerated creep analysis and lifetime prediction of structural components in high-temperature applications. Our multi-pronged approach motivates further integration of computational tools and advanced instrumentation to establish a universal framework for understanding high-temperature material responses.

36 MATERIALS SCIENCE↗

DOE OSTI2021

AC losses of Roebel and CORC ® cables at higher AC magnetic fields and ramp rates

We have measured ReBCO coated conductor-based conductor on round core (CORC ® ) and Roebel cables at 77 K in a spinning magnet calorimeter, which subjected the tapes in the samples to a radial magnetic field of 566 mT (peak) at frequencies up to 120 Hz (272 T s -1 , cyclic average) with an approximately sinusoidal waveform. The samples were oriented such that the field applied to the tapes within the cables was entirely radial, simplifying subsequent analysis. An expression for loss which included hysteretic, flux creep and eddy current losses was fit to both the CORC ® and the Roebel cables. This expression allowed easy comparison of the relative influence of eddy currents and flux creep (or power-law behavior) effects. The loss of both the CORC ® and Roebel cables measured here were seen to be essentially the sum of the hysteretic loss, flux creep effects, and the normal metal eddy current losses of the individual tapes. The losses of these cables were measured at high B × d B /d t with no coupling current loss observed under the present preparation conditions. The influence of flux creep effects on loss were not negligible. The losses of the CORC ® cable per meter of tape were seen to be reduced from the case of a flat tape because of the helical geometry of the tapes.

Physics↗

DOE OSTI2021

Accounting for the effect of dislocation climb-mediated flow on the anisotropy and texture evolution of Mg alloy, AZ31B

The current study explores the role that dislocation climb has in mediating plasticity a Mg alloy at moderately elevated temperatures. Interrupted tensile tests were performed on samples of Mg alloy, AZ31B, sheet in the O temper condition over a range of strain rates (10 -5 to 10 -1 s -1 ) and temperatures (20–350°C) along the rolling and transverse directions. Experimental measurements of the resulting strain anisotropy and texture evolution were used as constraints during a parametric study employing a new crystal plasticity model (VPSC-CLIMB), which explicitly accounts for the kinematics of dislocation climb. The results reveal that the climb of basal (a) dislocations is not only important for dislocation recovery, but also demonstrate that climb accommodates a significant fraction of the strain in conditions where a power-law creep-type constitutive response prevails. This work does not discredit the notion that non-basal slip of (a) and (c+a) dislocations is important over a wide range of temperatures and strain rates. However, it demonstrates that the activation of dislocation climb as the mechanistic change within the power law regime provides an explanation for a wide range of observations, including the simultaneous reduction in strain anisotropy, slowed texture evolution, and rapid increase in strain rate sensitivity. Finally, it is hypothesized that these conclusions may even apply to cases in which grain boundary sliding and/or dynamic recrystallization are observed.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Effect of Zr and Sc additions on coarsening- and creep resistance of AlSi10Mg fabricated by laser powder bed fusion

Microstructure and creep properties are studied in a eutectic AlSi10Mg alloy modified with Zr and Sc additions (Al-9.8Si-0.32Mg-0.70Zr-0.23Sc, wt%) manufactured through laser powder-bed fusion (L-PBF). Three types of Zr/Sc-bearing powders - elemental, master-alloy, and pre-alloyed - are employed in the fabrication process, with the pre-alloyed powders providing the highest incorporation of Zr and Sc in the Al matrix. Here, the as-printed alloy exhibits a fine cellular Al-Si eutectic structure which fragments and coarsens into micron-sized Si particles during aging at 300 ºC, leading to a steady drop in alloy microhardness between 0.1 and 1000 h. Coarsening of the eutectic Si phase during aging is not measurably affected by Zr and Sc in solid solution, which precipitate during aging and increases strength, compensating weakening from Si coarsening between 1 and 200 h at 300 ºC. Atom-probe analysis in the peak-aged condition (96 h/300 °C) confirms the presence of Al 3 (Sc,Zr) secondary nano-precipitates with an average radius of 1.0 nm and some Si solubility. Micron-sized grains are present throughout the alloy, with ultra-fine-grained regions at the melt pool boundaries, neither of which coarsen during long-term aging at 300 ºC. Under creep conditions at 300 °C, the Zr/Sc-bearing alloy with Al 3 (Sc,Zr) nano-precipitates exhibits power-law behavior, with a high apparent stress exponent (n a = 9) and a high threshold stress (σ th = 43 MPa), exhibiting nearly double the strength of a Zr/Sc-free AlSi10Mg control alloy (σ th = 22 MPa).

36 MATERIALS SCIENCE↗

DOE OSTI2021

A Power-Law Decrease in Interfacial Resistance Between Li 7 La 3 Zr 2 O 12 and Lithium Metal After Removing Stack Pressure

The high interfacial resistance between solid electrolytes and lithium metal is a hurdle to developing all solid-state batteries. External pressure applied on the lithium and solid electrolyte interface prior to electrochemical cycling is known to effectively lower the interfacial resistance. Here we report that the interfacial resistance between Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) and lithium metal decreases over time even after removing the external pressure. The irreversible decrease of interfacial resistance can be understood by a gradual reduction of the total energy of the system, including strain energy and interfacial energy. Under external pressure exceeding ~25 MPa, however, lithium can be squeezed into LLZTO, fracturing the ceramic solid electrolyte. As a result, these observations can help improve the understanding of lithium metal creep and the interactions between garnet-type solid electrolytes and lithium metal.

25 ENERGY STORAGE↗