Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pyrolysis Shrinkage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Detailed modeling of hydrogen release and particle shrinkage during pyrolysis of inhomogeneous wood

Hydrogen release during pyrolysis of woody biomass is studied considering anisotropicity and inhomogeneity of wood structure. A new anisotropic shrinkage model is proposed based on the decomposition of main wood constituents, i.e., cellulose, hemicellulose, and lignin. The new shrinkage model can predict the temporal evolution of the wood structure, and the differences between axial and radial shrinkage during pyrolysis. The model agrees very well with several experimental data from the literature. Based on particle temperature during conversion, the pyrolysis is partitioned into four stages, and the hydrogen release and H 2 formation from each stage are investigated. Stage (IV) of pyrolysis, from 1000 to 1273 K, is found to be efficient for H 2 production owing to the production of considerable mass of H with a minimal amount of tar species. Furthermore, the char quality is found to be different at the end of stages (II), (III), and (IV), where around 67.7, 80.5, and 93.4% wt. of solid residue is made of carbon, respectively. The model is also used to explain how the heating rate affects the temperature distribution inside the particle and how it shifts the peak of hydrogen release. Finally, the pyrolysis of two inhomogeneous wood samples — a beech twig with bark and a beech dowel with growth rings — are investigated. The bark can affect the pyrolysis rate, products, and flow pattern inside the particle. The growth rings do not have a considerable effect on the pyrolysis rate and products, but they have a significant impact on the flow pattern. This has an important implication for char conversion studies where the internal surface area and porosity field distribution have a significant effect on the gasification and oxidation rates.

09 BIOMASS FUELS↗
NASA NTRSDate not supplied

Updates to PATO’s Thermo-Mechanical Model

The solid mechanics module within the Porous material Analysis Toolbox (PATO) material response code was updated to model the stress contribution from both internal pressure and pyrolysis shrinkage as function of material’s decomposition. Incorporating these physical phenomena, alongside the previously included temperature dependent mechanical properties, thermal expansion, and aerodynamic loads, allows for a more accurate thermo-mechanical behavior modeling of Thermal Protection System (TPS) materials, which is critical to assess spallation risks during atmospheric entry. This poster outlines the workflow for obtaining the necessary PATO inputs, derived from dilatometry experiments, which are used to model the stress field in TPS materials due to thermal expansion and pyrolysis shrinkage. Furthermore, to analyze the relevance of the stress contribution from the internal pressure, a study was conducted using TACOT with different permeability values.

TPS↗
NASA NTRSDate not supplied

In Situ Synchrotron Micro-CT of Microballoon-Filled RTV Silicone During Thermal Decomposition

This work investigates the thermal decomposition of microballoon-filled room-temperature-vulcanizing (RTV) silicone using time-resolved synchrotron micro-CT at the Advanced Light Source. In situ imaging of constrained and unconstrained samples captures the evolution of the internal microstructure during heating, including material expansion, microballoon and void growth, tearing, pyrolysis, shrinkage, and increasing porosity. The measurements provide new insight into the mechanisms governing RTV degradation and generate three-dimensional data for future quantitative analysis and material-response model development.

TPS↗
NASA NTRS1985

A ceramic matrix composite based on polymerization and pyrolysis of ethynylated aromatics

A number of ethynylated aromatic monomers recently have been synthesized which thermally homopolymerize and copolymerize to produce rigid, highly cross-linked polymers with high thermal stability (Tg of about 450 C). On pyrolysis, these polymers lose few volatiles (more than 85 percent char yield) to yield carbon bodies of relatively low porosity. These properties render the ethynylated aromatics of significant interest as matrices for high temperature composites. Incorporation of a SiC particle filler in the matrix improves the rheology of the system and minimizes shrinkage during pyrolysis. Several unidirectional composites have been fabricated combining a graphite or boria-alumina-silica continuous reinforcement with an ethynylated aromatic polymer matrix and SiC filler. Thermogravimetric analysis of composite pyrolysis behavior was used to determine reaction kinetics and to establish a composite fabrication cycle. Composites retained 95 percent of their green weight on pyrolysis. Microstructure of the green and pyrolyzed composites is characterized for materials pyrolyzed at 600 C in vacuum and argon as well as for laminates heated at 1200 C in argon following pyrolysis.

Hurwitz, F. I.↗
DOE OSTI2022

Thermal properties of field-assisted-sintered SiCN–Y 2 O 3 composites

Polymer-derived amorphous SiCN has excellent high-temperature stability and properties. To reduce the shrinkage during pyrolysis and to improve the high-temperature oxidation resistance, Y 2 O 3 was added as a filler. In this study, polymer-derived SiCN–Y 2 O 3 composites were fabricated by mixing a polymeric precursor of SiCN with Y 2 O 3 submicron powders in different ratios. The mixtures were cross-linked and pyrolyzed in argon. SiCN–Y 2 O 3 composites were processed using field-assisted sintering technology at 1350°C for 5 min under vacuum. Dense SiCN–Y 2 O 3 composite pellets were successfully made with relative density higher than 98% and homogeneous microstructure. Due to low temperature and short time of the heat-treatment, the grain growth of Y 2 O 3 was substantially inhibited. The Y 2 O 3 grain size was ~1 μm after sintering. The composites’ heat capacity, thermal diffusivity, and thermal expansion coefficients were characterized as a function of temperature. The thermal conductivity of the composites ceramics decreased as the amount of amorphous SiCN increased and the coefficient of thermal expansion (CTE) of the composites increased with Y 2 O 3 content. However, the thermal conductivity and CTE did not follow the rule of mixture. This is likely due to the partial oxidation of SiCN and the resultant impurity phases such as Y 2 SiO 5 , Y 2 Si 2 O 7 , and Y 4.67 (SiO 4 ) 3 O.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Large-diameter carbon-composite monofilaments

Large-diameter carbon composite monofilaments with high strength and high modulus were produced by pregging multifiber carbon bundles with suitable organic resins and pyrolysing them together. Two approaches were developed to increase the utilization of fiber tensile strength by minimizing stress concentration defects induced by dissimilar shrinkage during pyrolysis. These were matrix modification to improve char yield and strain-to-failure and fiber-matrix copyrolysis to alleviate matrix cracking. Highest tensile strength and modulus were obtained by heat treatments to 2873 K to match fiber and matrix strain-to-failure and develop maximum monofilament tensile-strength and elastic modulus.

Bradshaw, W. G.↗
NASA NTRSDate not supplied

In-situ Imaging of Pyrolyzing Aerospace Materials

Tracking morphological changes of materials during heating is crucial to understand its response in fire protection, biofuel production, thermal protection systems (TPS) for hypersonic flight. As materials are heated, they undergo physical and chemical changes due to water loss, stretching or shrinking, pyrolysis and chemical reactions in the ambient environment. The effects of these changes can have a profound impact on the material’s performance, indicated by changes in on the porosity and volume. While materials such as wood shrink as they pyrolyze and lose mass, others swell due to their inherent characteristics when exposed to heat [1]. This study focuses on experiments conducted at the Advanced Light Source (ALS) beamline 8.3.2, where in situ micro-computed tomography (µ-CT) is performed on materials as they are being pyrolyzed. Through in situ µ-CT, the change in total volume and porosity can be obtained in real-time, allowing for better understanding of the underlying thermophysical and chemical processes as a function of temperature. This study also focuses on the implementation of the Porous Microstructure Analysis software (PuMA) [2] to obtain thermal conductivity, permeability, and other properties of the material from the 3D tomographies. The information gained from these tomographies will supplement microscale model development of material morphological change and will aid macroscale modeling for high-temperature applications. For this study, Room Temperature Vulcanizing silicone (RTV) [3-5] is heated from room temperature to 1000°C using an infrared lamp heating system, and tomographies are continuously collected as the sample is heated. The tomographies are then segmented to obtain solid and void phases, from which estimates of pore size, porosity and total volume are extracted as a function of temperature. PuMA is deployed on the segmented tomographies to obtain thermal conductivity, permeability, and other properties as a function of temperature. Preliminary results show that RTV first intumesces (swells) as pyrolysis begins, due to build-up of pyrolysis gases in closed pores, and then shrinks significantly as more open pores are formed and the pyrolysis gases outgas. Pore network visualization of the tomographies using OpenPNM [6] showed the increase in pore connectivity with increase in temperature. Future work will focus on using PuMA to obtain macroscopic properties of RTV as a function of temperature.

Tomography↗
NASA NTRS1998

Suspension of SiC Powders in Allyhydridopolycarbosilane (AHPCS): Control of Rheology

Inert particulate fillers can be blended with preceramic polymers prior to infiltration of composite preforms to increase pyrolysis yield and decrease shrinkage, thus reducing the number of infiltration/ pyrolysis cycles required for densification. However, particulate filler loadings and concentration of added dispersants necessary to maintain low viscosity (< 0.50 N.s/sq m) slurries vary with the characteristics of the particular AHPCS polymer batch. These batch to batch variations occur with alterations in the synthesis process and method of allyl substitution, which in turn alter polymer structure and molecular weight distribution. A number of different polymer batches were characterized by NMR, GPC and thermal analysis, and the influence of polymer structure on rheology of filled systems determined. When the high molecular weight fraction increased to too great a level, suitably fluid slurries could no longer be attained.

Hurwitz, Frances I.↗
DOE OSTI2022

Scalable, Infiltration-Free Ceramic Matrix Composite (SIF-CMC) manufacturing for Molten Salt Receiver: Investigation of particle-loaded preceramic resin

Due to their unique combination of high temperature, corrosion resistance, and toughness, Ceramic Matrix Composites (CMC) are the optimal materials to be used in the next generation of Concentrated Solar Power (CSP), which will operate at working temperatures up to 800 °C. However, today, CMC is too costly to be used in CSP applications due to its complex manufacturing process based on repeated infiltration-pyrolysis cycles. To solve this issue, PARC is developing a scalable, infiltration-free method (SIF) to manufacture CMC, which can reduce the production cost, increase batch consistency, and leverage all of the intrinsic advantages of current CMCs. The key to the SIF method is using a flowable preceramic resin with high loading of functional components. The formulation impregnates the fiber during curing and leads to high-density, low-shrinkage parts upon pyrolysis. In this paper, we demonstrate a proof-of-concept of the SIF process and report the relationships between key process parameters in the manufacturing process: functional material loading in the resin vs. resin’s flowability and morphology changes upon pyrolysis.

ceramic matrix composite, concentrated solar power↗
NASA NTRSDate not supplied

Thermo-Poro-Mechanical Modeling of RTV Intumescence

Room temperature vulcanizing (RTV) silicone is a high-temperature adhesive used as a gap-filler between heatshield tiles in numerous entry missions. Its propensity to intumesce, or swell upon exposure to heat, is a well-known effect that needs to be carefully quantified during design. At tile interfaces of charring ablators, intumescence, combined with differential recession, could cause the gap filler to protrude past the ablator outer mold line, forming a “fence”. Fencing can in turn cause transition to turbulence of the flow wetting the heat shield, leading to augmented surface heating. Recent experiments conducted at the Plasmatron X facility, the high enthalpy wind tunnel of the Center for Hypersonics and Entry Systems Studies, have shown prominent fencing of RTV gap fillers in PICA, under both nitrogen and air plasmas. Similar observations are well known in the arcjet literature. Further experiments under controlled environment, performed using in situ X-ray micro-computed tomography (micro-CT) at the Advanced Light Source (ALS), have shown heating rate-dependent swelling and shrinkage of RTV during pyrolysis. To simulate RTV intumescence, a novel model was introduced in the Porous Materials Analysis Toolbox based on OpenFOAM, PATO, to account for pore-pressure buildup within both closed- and open-pores. The governing equation for the thermo-poro-mechanical response were developed, assuming linear elasticity for the charring silicone. A new multi-pyrolysis model that tracks non-monotonic advancement of material properties with pyrolysis was proposed. This model addresses the limitations of state-of-the-art ablator models to capture the different stages of thermal degradation and coupled thermomechanics. Swelling of RTV was simulated using the new thermo-poro-mechanical model and compared against in situ micro-CT data. Results showed good agreement in intumescence height and temperature profiles at all heating rates, indicating that the key factor contributing to RTV swelling is the internal pressure build-up within closed- and open-pores. As RTV is cured into a soft (rubbery) compound with low-porosity and permeability, initial temperature increase and pyrolysis gas production cause a significant increase of internal pressure, causing a pronounced volume growth. As thermal degradation progresses, rigidization of the silicone occurs due to char hardening which counteract volume shrinkage after gas pressure relief. Overall, our model shows that accounting for changes in properties such porosity, permeability and key thermomechanical coefficients is crucial for capturing the RTV volume change during ablation and enable a predictive capability for heatshield tile interface response. A plan for future calibration of thermomechanical properties evolution during degradation is discussed, as a key next step to close the new model.

RTV↗
NASA NTRSDate not supplied

Thermo-Poro-Mechanical Modeling of RTV Intumescence

Room temperature vulcanizing (RTV) silicone is a high-temperature adhesive used as a gap-filler between heatshield tiles in numerous entry missions. Its propensity to intumesce, or swell upon exposure to heat, is a well-known effect that needs to be carefully quantified during design. At tile interfaces of charring ablators, intumescence, combined with differential recession, could cause the gap filler to protrude past the ablator outer mold line, forming a “fence”. Fencing can in turn cause transition to turbulence of the flow wetting the heat shield, leading to augmented surface heating. Recent experiments conducted at the Plasmatron X facility, the high enthalpy wind tunnel of the Center for Hypersonics and Entry Systems Studies, have shown prominent fencing of RTV gap fillers in PICA, under both nitrogen and air plasmas. Similar observations are well known in the arcjet literature. Further experiments under controlled environment, performed using in situ X-ray micro-computed tomography (micro-CT) at the Advanced Light Source (ALS), have shown heating rate-dependent swelling and shrinkage of RTV during pyrolysis. To simulate RTV intumescence, a novel model was introduced in the Porous Materials Analysis Toolbox based on OpenFOAM, PATO, to account for pore-pressure buildup within both closed- and open-pores. The governing equation for the thermo-poro-mechanical response were developed, assuming linear elasticity for the charring silicone. A new multi-pyrolysis model that tracks non-monotonic advancement of material properties with pyrolysis was proposed. This model addresses the limitations of state-of-the-art ablator models to capture the different stages of thermal degradation and coupled thermomechanics. Swelling of RTV was simulated using the new thermo-poro-mechanical model and compared against in situ micro-CT data. Results showed good agreement in intumescence height and temperature profiles at all heating rates, indicating that the key factor contributing to RTV swelling is the internal pressure build-up within closed- and open-pores. As RTV is cured into a soft (rubbery) compound with low-porosity and permeability, initial temperature increase and pyrolysis gas production cause a significant increase of internal pressure, causing a pronounced volume growth. As thermal degradation progresses, rigidization of the silicone occurs due to char hardening which counteract volume shrinkage after gas pressure relief. Overall, our model shows that accounting for changes in properties such porosity, permeability and key thermomechanical coefficients is crucial for capturing the RTV volume change during ablation and enable a predictive capability for heatshield tile interface response. A plan for future calibration of thermomechanical properties evolution during degradation is discussed, as a key next step to close the new model.

silicone intumescence↗
DOE OSTI2024

Insights into Preceramic Polymer-Based Additive Manufacturing Inks via Rheological and Scattering Studies of Preceramic Polymer-Grafted Nanoparticles Suspended in Polycarbosilane

Preceramic polymers (PCPs) offer advantages in producing ceramics due to their processability and ability to tailor the final chemistry of the produced material. However, challenges such as volumetric shrinkage and mass loss during pyrolysis often result in polymer-derived ceramics containing pores and cracks. PCP-grafted ceramic nanoparticles (PCPGNPs) have been proposed and studied as a route to mitigate the shrinkage issues associated with neat PCPs. Prior studies on PCPGNPs have principally focused on the synthesis and characterization of neat materials. Dispersing PCPGNPs in commercial preceramic polymer is another attractive, but underexplored, route to control the rheological and char yield properties of PCP systems. In this work, a systematic rheological study of commercial PCP (SMP-877) and PCPGNP (silica with poly(1,1-dimethylpropylsilane) corona) mixtures was executed to develop design rules for the processing of such systems. A rheological study demonstrated the effect of increasing particle concentration on network formation with percolation occurring between 50 and 60 wt %. Samples above the percolation threshold exhibited higher viscosities and rapid shear thinning thus demonstrating their direct-write printability. X-ray photon correlation spectroscopy (XPCS) corroborated the rheology and showed two diffusive modes when the material was above percolation. Mixtures of PCPGNPs and SMP-877 had synergistically higher char yields upon thermal treatment and pyrolysis. XPCS and rheological measurements during thermal treatment identified thermal jamming of the polymer grafts as a key factor in improving the char yield. In conclusion, with the insights gained here, we expect these mixed systems to provide attractive feedstocks for polymer-derived ceramics, with proof-of-principal application as feedstocks for direct ink write (DIW) additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Additively Manufactured Carbon Fiber-Reinforced Siliconized Silicon Carbide Composites Using Carbon Fiber-Reinforced Poly-Ether-Ether-Ketone (PEEK) as a Precursor

Herein, we report a method to additively manufacture carbon fiber-reinforced siliconized silicon carbide composites. The process involves the pyrolysis of a 3D-printed carbon fiber-reinforced poly-ether-ether-ketone (PEEK) composite to produce a porous carbon fiber-reinforced carbon matrix composite preform, which is subsequently infiltrated with molten silicon to obtain a carbon fiber-reinforced siliconized silicon carbide composite. A key aspect of the method is limiting polymer melt flow during pyrolysis of PEEK, which is achieved by thermally annealing the 3D-printed carbon fiber-reinforced PEEK preform in air at a temperature below PEEK’s melting temperature. Rheological and differential scanning calorimetry (DSC) measurements demonstrate that the thermal annealing treatment altered the melting behavior of PEEK, while NMR and FTIR measurements provided a mechanistic explanation for the structural changes responsible for the behavior. It was also found that dimensional changes during pyrolysis were anisotropic with greater shrinkage in the stacking direction of the material.

Yoon, Bola [ORNL] (ORCID:0000000260875373)↗
NASA NTRS2008

Refractory Ceramic Foams for Novel Applications

Workers at NASA Ames Research center are endeavoring to develop durable, oxidation-resistant, foam thermal protection systems (TPSs) that would be suitable for covering large exterior spacecraft surfaces, would have low to moderate densities, and would have temperature capabilities comparable to those of carbon-based TPSs [reusable at 3,000 F (.1,650 C)] with application of suitable coatings. These foams may also be useful for repairing TPSs while in orbit. Moreover, on Earth as well as in outer space, these foams might be useful as catalyst supports and filters. Preceramic polymers are obvious candidates for use in making the foams in question. The use of these polymers offers advantages over processing routes followed in making conventional ceramics. Among the advantages are the ability to plastically form parts, the ability to form pyrolized ceramic materials at lower temperatures, and the ability to form high-purity microstructures having properties that can be tailored to satisfy requirements. Heretofore, preceramic polymers have been used mostly in the production of such low-dimensional products as fibers because the loss of volatiles during pyrolysis of the polymers leads to porosity and large shrinkage (in excess of 30 percent). In addition, efforts to form bulk structures from preceramic polymers have resulted in severe cracking during pyrolysis. However, because the foams in question would consist of networks of thin struts (in contradistinction to nonporous dense solids), these foams are ideal candidates for processing along a preceramic-polymer route.

Stackpoole, M.↗
NASA NTRS1987

New Polymeric Precursors of Silicon Carbide

Silicon carbide made by pyrolizing polymers. Method conceived for preparation of poly(decamethylcyclohexasilanes) as precursors for preparation of silicon carbide at high yield. Technical potential of polysilanes as precursors of SiC ceramics being explored. Potential limited by intractability of some polysilanes; formation of small, cyclic polycarbosilane fragments during pyrolysis; and overall low char yield and large shrinkage in conversion to ceramics.

Litt, M.↗
DOE OSTI2023

Macroscale Fabrication of Lightweight and Strong Porous Carbon Foams through Template-Coating Pair Design

Manufacturing of low-density-high-strength carbon foams can benefit the construction, transportation, and packaging industries. One successful route to lightweight and mechanically strong carbon foams involves pyrolysis of polymeric architectures, which is inevitably accompanied by drastic volumetric shrinkage (usually >98%). As such, a challenge of these materials lies in maintaining bulk dimensions of building struts that span orders of magnitude difference in length scale from centimeters to nanometers. Here, this work demonstrates fabrication of macroscale low-density-high-strength carbon foams that feature exceptional dimensional stability through pyrolysis of robust template-coating pairs. The template serves as the architectural blueprint and contains strength-imparting properties (e.g., high node density and small strut dimensions); it is composed of a low char-yielding porous polystyrene backbone with a high carbonization-onset temperature. The coating serves to imprint and transcribe the template architecture into pyrolytic carbon; it is composed of a high char-yielding conjugated polymer with a relatively low carbonization-onset temperature. The designed carbonization mismatch enables structural inheritance, while the decomposition mismatch affords hollow struts, minimizing density. The carbons synthesized through this new framework exhibit remarkable dimensional stability (≈80% dimension retention; ≈50% volume retention) and some of the highest specific strengths (≈0.13 GPa g -1 cm 3 ) among reported carbon foams derived from porous polymer templates.

36 MATERIALS SCIENCE↗
NASA NTRS2008

High Temperature Aerogels in the Al2O3-SiO2 System

Al2O3-SiO2 aerogels are of interest as constituents of thermal insulation systems for use at high temperatures. Al2O3 and mullite aerogels are expected to crystallize at higher temperatures than their SiO2 counterparts, hence avoiding the shrinkages that accompany the formation of lower temperature SiO2 phases and preserving pore structures into higher temperature regimes. The objective of this work is to determine the influence of processing parameters on shrinkage, gel structure (including surface area, pore size and distribution) and pyrolysis behavior.

Hurwitz, Frances I.↗
DOE OSTI2022

Alkali-activated slag (AAS) and OPC-based composites containing crumb rubber aggregate: Physico-mechanical properties, durability and oxidation of rubber upon NaOH treatment

Value-added utilization of waste tires in cementitious materials has been studied for decades, whereas the synergy between rubber and alkali-activated cements deserves more investigations. To this end, we compared physico-mechanical and durability properties of alkali-activated slag (AAS) and OPC-based composites containing NaOH-pretreated/as-received crumb rubber (CR). It was found that the incorporation of CR had both positive and negative effects on specimens due to its special attributes. CR reduced electrical conductivity which was associated with the ion transport ability, since it worked as an electrical insulator and increased hydrophobicity of pore walls. The sulfate expansion decreased with CR content because the flow of sulfate ions was demobilized, and the flexibility of CR relieved the internal stress. CR also improved the freeze-thaw durability of composites if the total CR content was less than 30% in specimens. However, the low Young's modulus of CR impaired the compressive strength and failed to effectively control the total shrinkage upon drying. The composites with CR must avoid high temperature exposure which resulted in the pyrolysis of rubber. In addition, the NaOH pretreatment enhanced adhesion between CR and hydrated cement and improved overall performances of composites. The FTIR spectra confirmed the NaOH-induced accelerated oxidation of CR surface and the generation of polar functional groups including carbonyl and carboxyl groups, increasing the total surface energy of rubber. More importantly, the alkali-activation process for AAS could treat the CR aggregate in the meantime, which means the use of CR in alkali-activated cements does not require the pretreatment of CR before blending.

36 MATERIALS SCIENCE↗