Search NASA⌕ Search

SEARCH · Search NASA

Results for “REBCO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Examination of Through-Thickness/Through-Time Phase Evolution during an MOD-Type REBCO Precursor Conversion Using Raman Microsscopy

Through-thickness/through-time composition analyses were made on REBa{sub 2}Cu{sub 3}O{sub 6+x} (REBCO) films prepared from metal-organic deposited (MOD) precursors on a RABiTS (rolling-assisted biaxially textured substrate) template. Y Dy{sub 0.5}Ba{sub 2}Cu{sub 3}O{sub 6 + x} films were fabricated either by a single precursor coating or by two separate, equivalent precursor coatings with an intermediate decomposition. Specimens were quenched at selected times along a heat treatment profile that simulated conditions used by American Superconductor, then examined by Raman microscopy along mechanically milled slopes through the REBCO films. Upon reaching the reaction temperature TR, the precursor initially transforms into a (Y, Dy){sub 2}Cu{sub 2}O{sub 5}, CuO, Cu{sub 2}O, and RE-Ba-F-O phase mix, and this is followed shortly by substrate level REBCO formation that propagates upwards through time. Our results indicate that (1) the single layer (SL) and double layer (DL) films (both {approx} 1.2 {mu}m thick) react to completion at about the same rate and arrive at a similar final composition and (2) some residual Ba-Cu-O phases persist near the top of the fully reacted films. The performance of the SL film was moderately better than that of the DL film, seemingly due to better through-thickness REBCO texture as determined using x-ray diffraction.

36 MATERIALS SCIENCE↗

Width-bending characteristic of REBCO HTS tape and flat-tape Rutherford-type cabling

Abstract The width-bending behaviors for a rare earth barium copper oxide (REBCO) high-temperature superconducting (HTS) tape have been investigated. It has been found experimentally that the width-bending strain of a Yttrium Barium Copper Oxide (YBCO) tape does not degrade the critical current as much as is expected from the axial strain. The critical current is not directly affected by the width-bending strain but by the axial strain, which the width-bending strain generates by the Poisson effect. Since Poisson’s ratio is about 0.3, the axial strain effective on the critical current is about 30% of the width-bending strain. Therefore, the width-bending strain of even 1.5% degrades the critical current by only 15% if the REBCO layer side is bent inward. However, the critical current degraded by more than 70% when the REBCO layer is outward. The width-bending effects on the critical current have been further examined, considering Poisson’s ratio changes and the neutral plane shift of the REBCO tape substrate. Those changes would occur when the material yields due to severe width-bending. Based on the width-bending of REBCO tapes, flat-tape Rutherford-type cabling is discussed. A REBCO Rutherford-type cable can provide various advantages, especially for narrow-tape cabling. The flat-tape Rutherford-type cable has better characteristics against an electromagnetic transverse Lorentz force. Furthermore, the tape length of the cable can be approximately the same as the cable length allowing for excellent tape usage. REBCO Rutherford-type cabling will be a promising high-current, high-field cabling method using thin substrate REBCO tapes. It will be useful for AC ramp-field and pulse-field applications with low AC losses and low shield currents. It notes that the filaments in the cable are symmetrically distributed in parallel. Therefore, each filament’s inductance is uniform, and a uniform current distribution among the filaments can be obtained.

Physics↗

Suppressing Screening-Current-Induced Strain in a 72-mm-Bore REBCO Insert for a 20-T Magnet: A Numerical Study

Rare-earth barium copper oxide (REBCO) high-temperature superconducting (HTS) magnets are considered a game changer for the capability of generating magnetic fields exceeding 20 T at or above liquid helium temperature, combined with the potential for substantially reduced manufacturing and operational costs. Princeton Plasma Physics Laboratory is dedicated to developing large-bore high-field superconducting magnet systems to support forefront physics research. Here, our current project focuses on a φ72-mm cold-bore REBCO insert comprising 21 dry-wound double-pancake coils, designed to generate at least 8 T when nested within a 12-T outsert magnet. A significant challenge for high-field REBCO magnets is the time-varying-magnetic-field-induced screening currents (SC) in the REBCO conductors, which can cause localized strain and stress concentrations. This paper presents a numerical study of the SC-induced strain in the REBCO insert magnet, confirming that the SC-induced strain can be substantially suppressed by energizing the REBCO insert before the outsert magnets. We discuss and reveal the mechanism behind this reduction. By applying this strategy, we expect to unleash the potential of the REBCO insert magnet to generate up to 12 T in a 12-T background field.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development and performance of high-temperature superconducting CORC ® cables with CFD REBCO tapes

Abstract Increasing the normal zone propagation velocity (NZPV) in superconducting cables based on rare earth barium copper oxide (REBCO) tapes is expected to cause a paradigm shift by enabling the development of faster and more reliable quench detection systems to mitigate the development of destructive hot spots. Furthermore, a higher NZPV is beneficial in terms of fault current limitation capabilities by accelerating the homogenization of the quench in superconducting power devices. One way envisioned to increase the NZPV of cables based on REBCO tapes is the current flow diverter (CFD) concept. A Conductor on Round Core (CORC ® ) cable made with CFD REBCO tapes, called CFD CORC ® cable, and a CORC ® cable made with regular REBCO tapes, were fabricated and tested. The critical current of the CFD and regular CORC ® cables were obtained at temperatures ranging from 67 to 77 K in self-field. Measurements showed that the NZPV was increased by a factor of 4–4.5 in the case of the CFD CORC ® cable. Furthermore, the results suggest that the NZPV depends only on the applied current, similar to what has been observed previously on single REBCO tapes. These results demonstrate the successful integration of CFD REBCO tapes in CORC ® cables, without compromising their superconducting properties or their enhanced NZPV. The possibility of enhancing the NZPV of REBCO-based cables could facilitate quench detection, which remains an important issue in HTS magnet applications. This advancement also holds promise for the fault current limitation functionality of CORC ® cables.

Ben Saâd, Haïfa (ORCID:0000000216205364)↗

A viable dipole magnet concept with REBCO CORC ® wires and further development needs for high-field magnet applications

REBCO coated conductors maintain a high engineering current density above 16 T at 4.2 K. That fact will significantly impact markets of various magnet applications including high-field magnets for high-energy physics and fusion reactors. One of the main challenges for the high-field accelerator magnet is the use of multi-tape REBCO cables with high engineering current density in magnet development. Several approaches developing high-field accelerator magnets using REBCO cables are demonstrated. In this paper, we introduce an alternative concept based on the canted cos θ (CCT) magnet design using conductor on round core (CORC®) wires that are wound from multiple REBCO tapes with a Cu core. We report the development and test of double-layer three-turn CCT dipole magnets using CORC ® wires at 77 and 4.2 K. The scalability of the CCT design allowed us to effectively develop and demonstrate important magnet technology features such as coil design, winding, joints and testing with minimum conductor lengths. The test results showed that the CCT dipole magnet using CORC ® wires was a viable option in developing a REBCO accelerator magnet. One of the critical development needs is to increase the engineering current density of the 3.7 mm diameter CORC® wire to 540 A mm -2 at 21 T, 4.2 K and to reduce the bending radius to 15 mm. Furthermore, this would enable a compact REBCO dipole insert magnet to generate a 5 T field in a background field of 16 T at 4.2 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

New insight into strain and composition of BaZrO 3 nanorods in REBCO superconductor

We report on strain and composition effects associated with growth of self-assembled BaZrO 3 (BZO) nanorods in REBa 2 Cu 3 O 7–δ (REBCO) superconductors (RE = rare earth = Y and Gd), which have a profound effect on flux pinning and in-field critical current performance. The a-b plane mismatch between BZO and REBCO is never fully coherently accommodated. Instead, the nanorods always assume a size at least one unit cell smaller than the corresponding 'hole' in the REBCO matrix, thus providing deep minima of in-plane mismatch strain. Next, we show that the nominal BZO nanorods are in fact solid solution Ba 2+ (Zr 4+ 1–z RE 3+ z )O 3–δ perovskite, thus strongly affecting the stoichiometry and relative amounts of REBCO and BZO. We demonstrate that by varying only the Ba content in the nominal composition of 15 mol.% BZO + REBCO, the unit cell density of BZO can be tuned from 5% to 23%, and the linear density of RE 2 O 3 (REO) precipitates from 18 to 1 μm –1 . Furthermore, the results explain the wide range of pinning performances observed for the same nominal amount of Zr addition and provide insight into the mechanisms behind the complex phenomenon of growth of nanorods by self-assembly in REBCO superconductors.

2G-HTS↗

Characterization of edge damage induced on REBCO superconducting tape by mechanical slitting

Abstract Rare-earth barium-copper-oxide (REBCO) superconductors are high-field superconductors fabricated in a tape geometry that can be utilized in magnet applications well in excess of 20 T. Due to the multilayer architecture of the tape, delamination is one cause of mechanical failure in REBCO tapes. During a mechanical slitting step in the manufacturing process, edge cracks can be introduced into the tape. These cracks are thought to be potential initiation sites for crack propagation in the tapes when subjected to stresses in the fabrication and operation of magnet systems. We sought to understand which layers were the mechanically weakest by locating the crack initiation layer and identifying the geometrical conditions of the slitter that promoted or suppressed crack formation. The described cracking was investigated by selectively etching and characterizing each layer with scanning electron microscopy, laser confocal microscopy, and digital image analysis. Our analysis showed that the average crack lengths in the REBCO, LaMnO 3 (LMO) and Al 2 O 3 layers were 34 μ m, 28 μ m, and 15 μ m, respectively. The total number of cracks measured in 30 mm of wire length was between 3000 and 5700 depending on the layer and their crack densities were 102 cracks mm −1 for REBCO, 108 cracks mm −1 for LMO, and 183 cracks mm −1 for Al 2 O 3 . These results indicated that there are separate crack initiation mechanisms for the REBCO and the LMO layers, as detailed in the paper. With a better understanding of the crack growth behavior exhibited by REBCO tapes, the fabrication process can be improved to provide a more mechanically stable and cost-effective superconductor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Strain Distribution in REBCO-Coated Conductors Bent With the Constant-Perimeter Geometry

Here, cable and magnet applications require bending REBa 2 Cu 3 O 7-δ (REBCO, RE = rare earth) tapes around a former to carry high current or generate specific magnetic fields. With a high aspect ratio, REBCO tapes favor the bending along their broad surfaces (easy way) than their thin edges (hard way). The easy-way bending forms can be effectively determined by the constant-perimeter method that was developed in the 1970s to fabricate accelerator magnets with flat thin conductors. The method, however, does not consider the strain distribution in the REBCO layer that can result from bending. Therefore, the REBCO layer can be overstrained and damaged even if it is bent in an easy way as determined by the constant-perimeter method. To address this issue, we developed a numerical approach to determine the strain in the REBCO layer using the local curvatures of the tape neutral plane. Two orthogonal strain components are determined: the axial component along the tape length and the transverse component along the tape width. These two components can be used to determine the conductor critical current after bending. The approach is demonstrated with four examples relevant for applications: a helical form for cables, forms for canted cos θ dipole and quadrupole magnets, and a form for the coil end design. The approach allows us to optimize the design of REBCO cables and magnets based on the constant-perimeter geometry and to reduce the strain-induced critical current degradation.

(REBCO RE = rare earth) coated conductors↗

Correlations Between In-Line X-ray Diffraction Data and In-Field Critical Current of Long, 4-μm Thick Film REBCO Tapes Made by Advanced MOCVD

REBa 2 Cu 3 O 7-δ (REBCO, RE = rare earth) tapes with high critical current can be very impactful in high magnetic field applications at low temperatures and power applications at high temperatures. A pilot-scale Advanced Metal Organic Chemical Vapor Deposition (MOCVD) method was used to fabricate 50-m-long, 4+μm-thick REBCO tape in a single pass. Critical currents 3.3x that of commercial HTS tapes were achieved at 20 K, 12 T in these 50-m-long tapes. An in-line 2D X-ray Diffraction (XRD) system has been used to assess the quality of the long tapes in real-time, during manufacturing. The key peaks of REBCO, REO, and BZO phases were identified and utilized for tape quality analysis. Furthermore, a 20-m tape made by Advanced MOCVD was tested over its entire length by reel-to-reel (R2R) scanning Hall-probe microscopy (SHPM) at 65 K, 0.25 T, 2 T, and 4 T. 4-mm-wide strands of Advanced MOCVD tapes showed mean critical currents at 65 K of 530 A, 200 A, and 104 A at 0.25 T, 2 T, and 4 T respectively. The combined use of in-line and offline characterization techniques provides a reliable approach for assessing long REBCO tapes during manufacturing, serving as an effective feedback source for quality control in scaled-up REBCO tape deposition processes. This advancement contributes to the production of longer and more uniform high-performance REBCO tapes for large-scale, high-field superconducting applications

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A round bobbin critical current measurement and thermal runaway simulation of REBCO coated conductors

A round bobbin test has been widely used to measure critical current Ic of practical superconductors including Nb–Ti, Nb3Sn, and Bi-2212 round strands at 4.2 K and in high magnetic fields but rarely used for rare earth-barium-copper-oxide (REBCO) coated conductor tapes. Here, we applies this method to REBCO tapes and test their Ic at 77 K, self-field, and 4.2 K with a magnetic field of 14 T applied parallel to the tape. The sample carries very high current densities; it is 1.3 m long and has a dense array of voltage taps that allows probing localized thermal runaways and correlation with Ic variations along the length. At 77 K, the Ic values of all sections were measured and found to be rather uniform. However, at 4.2 K, we found that a 3 cm section has 90% of the overall voltage drop and it went into thermal runaways upon further increasing current. Thus, at 4.2 K, we were prevented by localized thermal runaways and unable to determine Ic of most of the REBCO conductor sections; this behavior is different from Bi-2212 and Bi-2223 for which Ic of all turns of a round barrel sample can be determined. We simulate REBCO tapes during current ramping to a thermal runaway and analyze impacts of various factors including cooling, conductor n-values, and thickness of stabilizer on the thermal runaway current Iq. The combined experiments and simulations identify n-value as a crucial factor that leads to the observed differences between Bi-2212 and REBCO. Together with cooling and the standard deviation of Ic variations along the length, the n-value determines whether Iq is above or below the average Ic of a long piece of conductor and their ratio Iq/Ic,ave, greatly affecting quench detection and thermal runaway prevention strategies of Bi-2212 and REBCO magnets.

Mosat, Marek↗

Characterization of long-length, MOCVD-derived REBCO coated conductors.

A leading approach to the fabrication of long-length, high-performance REBa{sub 2}Cu{sub 3}O{sub 7} (REBCO) coated conductor is by metal-organic chemical vapor deposition (MOCVD) of REBCO on buffered templates. Templates are produced by ion beam assisted deposition of textured MgO onto polished metal substrates. The overall performance of MOCVD coated conductors achieved to date is impressive, but further improvement is desired. We have used a coordinated set of characterization techniques to identify the underlying causes for critical current (Ic) performance variations in long-length MOCVD conductors. Using electron microscopy and Raman spectroscopy, we studied tape specimens from specially designed experiments performed in SuperPower's MOCVD manufacturing equipment with its six-track ldquohelixrdquo tape path. We find that in multi-pass depositions used to produce thicker REBCO films, the REBCO phase uniformity and texture quality in the first pass play key roles in pass-to-pass microstructure evolution, with nucleation of second phase particles in the first layer promoting misoriented grains that propagate through subsequent layers. These misoriented grains, many growing in close proximity with second phase particles, present current-blocking obstacles that limit Ic performance. Our results show that achieving more uniform deposition in the very first deposited layer plays a critical role that in turn leads to reduced misoriented grain content and REBCO lattice disorder in the second and subsequent layers of the REBCO film.

36 MATERIALS SCIENCE↗

Metal-Insulation REBCO Pancake Coil With Solder Surface Shunt: Testing and Modeling

Rare-earth barium copper oxide (REBCO) high-temperature superconducting (HTS) magnets can generate very high magnetic fields with superior engineering current density and robust mechanical integrity. The no-insulation (NI) winding technique, including its metal-insulation (MI) variant, enables “self-protection” against localized overheating through inter-turn current sharing, improving defect tolerance and allowing temporary current overloads. In REBCO pancake coils, the current-sharing path is predominantly confined to the edges of the REBCO tapes due to insulating buffer layers. Applying a surface shunt using solder can effectively enhance current sharing in NI/MI coils via the REBCO tape edges. Here, in this paper, we present both experimental and numerical research on the current distribution in surface-shunt metal-insulation (SSMI) REBCO pancake coils. We tested a stainless steel co-wound MI REBCO double-pancake coil, before and after applying a soldered surface shunt, in a saturated liquid nitrogen bath. The SSMI coil was modeled using the H-formulation and rotated anisotropic resistivity to study its dynamic behavior, including inter-turn current sharing and intra-turn screening currents. Benchmarked by experimental data, the numerical model is able to study the defect tolerance of the SSMI coil during energization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An electric-circuit model on the inter-tape contact resistance and current sharing for REBCO cable and magnet applications

REBCO coated conductor has demonstrated high current capacity that can enable high-field magnets for high energy physics and fusion applications. However, quench protection is still one of the main challenges to be addressed for these applications. In addition, Ic and n value variations along the length of REBCO tapes exist in commercial production. The inter-tape contact resistance plays a key role to develop the self protection capability in cables and magnets by enabling current sharing and suppressing excessive eddy currents. Here we propose an electric-circuit model to describe the inter-tape contact resistance and its impact on the current sharing between REBCO tapes. We report the experiments on a 2-stacked tape REBCO cable with local Ic drop to validate the model. With the developed model, we study the upper limit of the contact resistance which allows current sharing between tapes. We also study the impact of variation in Ic and n values in tapes on the cable performance. Finally, our model is expected to provide useful insight into the current sharing and target values for inter-tape contact resistance in REBCO cables and magnets for various applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Degradation of REBCO coated conductors due to a combination of epoxy impregnation, thermal cycles, and quench: Characteristics and a method of alleviation

REBa2Cu3Ox (REBCO) coated conductors are an enabling technology for >1 GHz nuclear magnetic resonance spectrometers that need >23.5 T solenoids, compact high-field fusion reactors beyond the International Thermonuclear Experimental Reactor, and 20 T class accelerator magnets. An in-depth understanding of stress and strain management is critically needed for these applications. Here, we report experimental data and an analysis of damages of REBCO-coated conductors in several scenarios relevant for their applications in high-field magnets and unique to their multi-layer thin film structure. The examined scenarios include failure induced by quench, failure induced by epoxy impregnation, and failure induced by a combination of epoxy impregnation and quench. The root cause is film blistering and peeling induced by thermally interfacial stresses characteristic of multilayered heteroepitaxial thin film structures on thick substrates utilized. The quantitative stress analysis is introduced using simple and easy to use formulas and clearly indicates how materials and structural characteristics affect the magnitude and the distribution of stresses and deflections. Finally, a simple method is introduced for removing degradation of REBCO coated conductors due to epoxy impregnation. Our data and analysis help our understanding of the practical limit of REBCO-coated conductors and can be utilized as a guidance for the physical design of REBCO coated conductors and high-current cables assembled from them and for minimizing damages.

Yin, Shijian (ORCID:0000000224312274)↗

Engineering current density over 5 kA mm -2 at 4.2 K, 14 T in thick film REBCO tapes

We report on remarkably high in-field performance at 4.2 K achieved in >4 $μ$m thick rare earth barium copper oxide (REBCO) samples with Zr addition. Two different samples have been measured independently at Lawrence Berkeley National Laboratory and the National High Magnetic Field Laboratory, achieving critical current densities ( J c ) of 12.21 MA cm -2 and 12.32 MA cm -2 at 4.2 K, 14 T ($\small{B}$|| c ), respectively, which corresponds to equivalent critical current ( I c ) values of 2247 and 2119 A/4 mm. These I c values are about two times higher than the best reported performance of REBCO tapes to date and more than five times higher than the commercial HTS tapes reported in a recent study. The measured J c values, with a pinning force of ~1.7 T N m -3 are almost identical to the highest value reported for thin (~1 $μ$m thick) REBCO at the field and temperature, but extended to very thick (>4 μm) films. This results in an engineering current density ( J e ) above 5 kA mm -2 at 4.2 K, 14 T, which is more than five times higher than Nb 3 Sn and nearly four times higher than the highest reported value of all superconductors other than REBCO at this field and temperature. The reported results have been achieved by utilizing an advanced metal organic chemical vapor deposition system. This study demonstrates the remarkable level of in-field performance achievable with REBCO conductors at 4.2 K and strong potential for high-field magnet applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-current, double-sided REBCO tapes by advanced MOCVD

Abstract An approach to fabricate double-sided, high-current RE-Ba 2 Cu 3 O 7− δ (REBCO) tapes for use in ultrahigh-field superconducting magnets operating at and above 20 T is demonstrated. In this work, we modified our advanced metal organic chemical vapor deposition (A-MOCVD) reactor to deposit REBCO films on each side of a double-sided buffer substrate in a single pass. The composition, thickness, and critical current ( I c ) of 1 µ m-thick REBCO films on each side of the double-sided tapes are compared. Double-sided REBCO tape with 2 µ m-thick films on each side showed self-field critical current density ( J c ) over 2.6 MA cm −2 at 77 K and 0 T. 15%-Zr-added double-sided REBCO tape showed I c over 530 A/4 mm at 20 K, 20 T.

Paidpilli, M.↗