Critical-speed analysis of flexibly mounted rigid rotors
Critical speed of flexibily mounted rigid rotors in undampened bearings
Cavicchi, R. H.↗
SEARCH · Search NASA
Results for “RIGID MOUNTING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Critical speeds of a rotor in rigidly mounted, externally pressurized, air-lubricated bearings
Calculation of rotor critical speeds for two bearing rotor system from rigid body theory using film stiffness as determined from zero speed, load eccentricity data
Cunningham, R. E.↗
Coupled two-degree-of-freedom response of soft- mounted rigid body to random excitation.
Mode coupling effect on response of rigid body to random excitation analyzed, using two degree of freedom model
DYNAMIC RESPONSE↗
Strain arrestor plate for mounting rigid insulating tiles
Plate is made of material having coefficient to thermal expansion similar to that of insulating material. Although plate may be formed from appropriate alloy, it has been found that a combination of graphite fibers in epoxy resin is satisfactory and much lighter in weight.
Kural, M. H.↗
New features of different frequency generating systems due to the use of electrodeless rigidly mounted VBA quartz crystal resonator
The BVA 5 MHz crystal equipped frequency sources exhibit a new blend of performances such as 10 to 11 daily stability, 5x10-13 short term stability (1 to 30 s time intervals) and close to the carrier low phase noise (1 Hz : -120 dBc, 10 Hz : -140 dBc), whereby retaining the customary crystal oscillator benefits of small volume, high reliability and low price, as opposed to more sophisticated frequency generators which would be required to achieve comparable performances. Examples illustrating the impact of the Oscilloquartz BVA oven-controlled crystal oscillator in different frequency generating systems are presented: cesium frequency standards; hydrogen frequency standard; a precision distribution sub-system for satellite ground stations; and high hierarchy exchanges of digital networks, synchronized by the master-slave method are discussed.
Jendly, A.↗
Vibration transmission through rolling element bearings. III - Geared rotor system studies
The bearing matrix formulations proposed by Lim and Singh (1990) are extended to analyze the overall dynamics of a geared rotor system which includes a spur gear pair, shafts, rolling-element bearings, a motor, a load, a casing, and flexible or rigid mounts. For this purpose, discrete vibration models are developed and used to predict vibration transmission through the bearings and to investigate the effects of the bearing, casing, and mount dynamics on the dynamic characteristics of the internal rotating system. Analytical predictions show that the theory is capable of predicting the bearing and mount moment transmissibilities in addition to the force transmissibilities. The predicted flexural vibrations of the casing plate are in good agreement with measurements conducted on an experimental set-up that consisted of a high-precision beam and pinion, and four identical rolling element bearings contained in a flexible casing mounted rigidly on a massive foundation.
Lim, T. C.↗
Adjustable Optical Mount Is More Rigid
Improved mount for lens or mirror in laser offers rigidity similar to that of nonadjustable optical mount. In comparison with older adjustable optical mounts, this one less susceptible to movements and distortions caused by vibrations and by thermal expansions and contractions. Mount contains neither adjustment rods (which grow or shrink as temperature varies) nor springs (which transmit vibrations to mounted optic).
Asbury, Bill G.↗
Reflection-Type Oil-Film Skin-Friction Meter
Oil-film skin-friction meter for both flight and wind-tunnel applications uses internal reflection and is self-contained, compact unit. Contained in palm-sized housing, in which source of light, mirrors, and sensor mounted rigidly in alignment. Entire unit mounted rigidly under skin of aircraft or wind tunnel, eliminating any relative vibration between optical elements and skin of aircraft or wind tunnel. Meter primarily applicable to flight and wind-tunnel tests, also used in chemical-processing plants.
Bandyopadhyay, Promode R.↗
The flexible mounting of an airplane engine
Discussed here is the suggested installation of the 'unbalanced' 8-cylinder VE-engine. The suggestion was that a flexible mounting be used instead of bolting the engine rigidly to the airplane structure. It was concluded that a flexible connection between the engine and the airplane is probably possible. A flexible connection primarily diminishes the vibrations due to inertia and, to a lesser degree, those due to torque variation. However, engines vibrate more when freely suspended than when rigidly mounted, and this vibration has a detrimental effect on all connections between the engine and the airplane. Therefore, in view of the relatively insignificant advantages which may be derived from the elastic suspension of the engine, the present rigid mounting is to be preferred. Vibration reduction can be achieved by incorporating in the fuselage as many of the rigid airplane parts as possible.
Kutzbach, K↗
Adjustable mount for a trihedral mirror Patent
Adjustable rigid mount for trihedral mirror formed of alloy with small coefficient of thermal expansion supporting screws and spring-biased plates
Laurie, R. O.↗
Statistical determination of space shuttle component dynamic magnification factors
A method is presented of obtaining vibration design loads for components and brackets. Dynamic Magnification Factors from applicable Saturn/Apollo qualification, reliability, and vibroacoustic tests have been statistically formulated into design nomographs. These design nomographs have been developed for different component and bracket types, mounted on backup structure or rigidly mounted and excited by sinusoidal or random inputs. Typical nomographs are shown.
Lehner, F.↗
Device and method for frictionally testing materials for ignitability
Test apparatus for determining ignition characteristics of various metal in oxidizer environments simulating operating conditions for materials is invented. The test apparatus has a chamber through which the oxidizing agent flows, and means for mounting a stationary test sample therein, a powered, rotating shaft in the chamber rigidly mounts a second test sample. The shaft is axially movable to bring the samples into frictional engagement and heated to the ignition point. Instrumentation connected to the apparatus provides for observation of temperatures, pressures, loads on and speeds of the rotating shaft, and torques whereby components of stressed oxygen systems can be selected which will avoid accidental fires under working conditions.
Benz, F. J.↗
Application of Digital Image Correlation in Wind Tunnel
Digital image correlation (DIC) is a non-contact measurement technique that has been used in various applications in multiple industries, from microscopic specimens all the way to large scale structures. This project involved using DIC to capture wing deflection under simulated wind loading at various angles of attack (AoA). A subscale model of a fixed-wing aircraft, shown in Figure 1, was used in the 14-footby 22-footsubsonicwind tunnel at the NASA Langley Research Center. The setup used two pairs of cameras mounted on the ceiling of the tunnel to view the starboard and port side wings. Aluminum framing was used to rigidly mount the cameras to beams in the ceiling. Camera setup challenges due to the confined space included obtaining even lighting and working around infrared (IR) cameras that were used to capture the flow over the wing. Remote connection was used to access data acquisition computers from computers in the control room. Eight measurement locations on each wing were made of 1-inch-diametercircular silver dry transfer decals that did not alter the air flow across the wing. These circles were speckled with a black ink pen and were used for the IR camera as well as for DIC systems. A mock setup outside the wind tunnel was used to optimize the camera setup and verify that the speckled tape provided sufficient correlation. DIC was used to track the position of seven locations as the AoA of the subscale model changed from −10 degrees to +10 degrees in 1-degree increments. The model was rotated at a fixed height about the center of the fuselage from −7 degrees to +10 degrees. The height of the model had to be lowered to achieve AoA slower than −7degrees due to geometric constraints of the cart supporting the model and the wind tunnel. The source of light was stationary relative to the model, so the exposure time had to be adjusted for different wing regions and AoA values. The three-dimensional (3D) visualization of the markings and the two-dimensional (2D) projection of these points onto the port wing at 0-degree AoA is shown in Figure 2.
Matlock Mennu↗
On-Ground Calibration and Optical Alignment for the Orion Optical Navigation Camera
The Orion Multi-Purpose Crew Vehicle on-board Navigation System will utilize the Optical Navigation measurements of the Moon and Earth during cis-lunar operations. Misalignment or an un-calibrated optical navigation camera may cause large measurement residuals in any on-board attitude determination and navigation system. Therefore, a novel estimation technique to calibrate the internal camera parameters, and a high accuracy optical alignment procedure to estimate the external camera alignment are introduced in this paper. The intrinsic camera parameters such as the focal length, the principle point offsets, and the camera lens distortion parameters will be estimated and evaluated using images of star fields. This calibration estimation technique can be used either on-ground or in flight. The proposed technique in this paper is using the discrepancy between imaged star vectors attained from the OpNav camera, and the matched star vectors from the star catalog to determine the changes in internal camera parameters. This gave rise to the two basic types of calibration the attitude dependent and attitude independent methods. The former utilizes the errors in imaged and cataloged vectors themselves, and the latter using the discrepancy in angles between pairs of vectors from the camera and catalog. The alignment procedure is carried out using Theodolite autocollimator measurements taken off alignment cubes mounted on the Orion frame and also the measurements from the OpNav focal plane. It is assumed that the alignment cubes and OpNav camera are rigidly mounted to the frame so that flexing effects do not significantly alter the orientation of the cubes relative to the OpNav camera.
Samaan, Malak↗
Scanning SQUID microscopy in a cryogen-free dilution refrigerator
We report a scanning superconducting quantum interference device (SQUID) microscope in a cryogen-free dilution refrigerator with a base temperature at the sample stage of at least 30 mK. The microscope is rigidly mounted to the mixing chamber plate to optimize thermal anchoring of the sample. The microscope housing fits into the bore of a superconducting vector magnet, and our design accommodates a large number of wires connecting the sample and sensor. Through a combination of vibration isolation in the cryostat and a rigid microscope housing, we achieve relative vibrations between the SQUID and the sample that allow us to image with micrometer resolution over a 150 μm range while the sample stage temperature remains at base temperature. To demonstrate the capabilities of our system, we show images acquired simultaneously of the static magnetic field, magnetic susceptibility, and magnetic fields produced by a current above a superconducting micrometer-scale device.
47 OTHER INSTRUMENTATION↗
Experimental and computational investigation of interactive flow induced oscillations of two tandem rough cylinders at 3×10 4 ≤Re≤1.2×10 5
The interactive flow induced oscillations (FIO) of two adjacent, elastically mounted, rigid, tandem, locally-rough cylinders in transverse flow direction are analyzed utilizing two-dimensional Unsteady Reynolds-Averaged Navier-Stokes (2-D URANS) equations and verified experimentally in the proximity-wake region. Three sets of experiments and simulations (K = 600N/m, ζ = 0.14; K = 600N/m, ζ = 0.26; K = 1,200N/m, ζ = 0.26; K is spring stiffness, ζ is damping ratio) of two tandem cylinders with turbulence stimulation are tested and simulated for Reynolds number in the range of 30,000 = Re ≤ 120,000. The reduced velocity range is U* = 2.48–14.22, the mass ratio is m* = 1.343, and the center-to-center in-flow spacing to diameter ratio is d/D = 2.57. The characteristics of amplitude response, frequency response, lift force, and interactive wake patterns are presented and discussed. The trends of the amplitude and frequency responses from numerical simulations are in good agreement with experimental results. The main conclusions of Reynolds number effect on interactive flow induced oscillations are: (1) Five significant flow patterns between two tandem locally-rough cylinders for different Reynolds numbers are observed through analyzing the complex but stable interactions between vortices and cylinders. (2) In the initial and upper VIV branches, the downstream cylinder's FIO is seriously interfered by the wake of the upstream cylinder. (3) The downstream cylinder is strongly impinged by the vortices shed from the upstream cylinder resulting in nearly 180O out-of-phase oscillations in transition from VIV to galloping and in-phase oscillations in galloping.
42 ENGINEERING↗
Performance of Windows in Walls With Continuous Insulation
Window openings in walls are a significant contributor to poor thermal performance because of thermal bridging through the framing members (e.g., studs, joists, plates, bracing) and because windows lack the thermal properties of insulation. Window installation guidance for walls with continuous insulation (CI) is critical for continued market growth of this energy efficiency technology. This research project offers window manufacturers a starting point and a potential path toward developing installation instructions for windows over CI. The objectives of the research include evaluating the common method for installing windows in walls with CI, as well as establishing acceptance criteria for evaluating the performance of windows installed in walls with and without CI. The research measures: 1. The performance characteristics (e.g., water management, structural integrity) of windows in walls without CI. 2. The performance of different thicknesses and types of CI used in walls. 3. The performance of different types of window assemblies (e.g., double-hung windows, mulled double-hung windows, mulled casement windows, and slider windows) installed over CI. 4. The performance of window flange types (e.g., rigid mounting and less robust flanges) installed over CI. 5. Installing windows over CI using baseline installation instructions versus window manufacturer installation instructions. The project’s sequential testing protocol consists of the following: • A water penetration resistance testing adapted from two ASTM standards: E331 (uniform static air pressure in four steps) and E547 (cyclic static air pressure) • A temperature cycling adapted from ASTM E2264 Method B (convective hot air) • A service condition wind loading test adapted from ASTM E330 • A six-month vertical displacement observation phase prior to the structural performance testing • A final water penetration resistance test after vertical displacement observation • A structural performance test adapted from ASTM E330. Key research findings include: • The criterion for passing a water penetration resistance test is that there is no water overflowing at the interior face of the studs. If there is any bubbling or slight pooling of water at the sill, then it must recede after the pressure is removed. Excessive leakage and/or water leaking to the interior face of the framing around the window constitutes a failure. • All single double-hung windows installed directly to lumber or over oriented strand board passed all test protocols. • For most wall specimens, the test results showed that the use of foam sheathing did not affect the performance of the window for water leakage. • All wall specimens underwent temperature cycling. The results indicated that temperature cycling had little to no effect on windows installed over foam sheathing. • For wall specimens that underwent six-month vertical displacement monitoring, the results showed that windows installed over foam sheathing do not sag over time. • The single-hung and double-hung windows installed using window manufacturer installation instructions passed the structural performance test, compared to failures observed in windows that were installed using generic installation instructions. The generic and manufacturer installation methods differed on the following construction details: type of fasteners, fastening patterns on the flanges, and window shimming details. • Additional testing is required to determine methods to improve structural pressure performance of slider windows. Potential solutions that would require additional testing may include fastener spacing, different types of fasteners, masonry window clips, construction adhesive, foam sealant, stronger window flange material, and/or straps.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Interferometer construction assures parallelism of critical components
Interferometer with rigidly mounted components assures parallelism of critical components. The interferometer is constructed for effective operation even if the total instrument is subjected to mechanical stress.
Connes, P.↗