Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLLING CONTACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Effect of tangential traction and roughness on crack initiation/propagation during rolling contact

Rolling fatigue tests of 0.45 percent carbon steel rollers were carried out using a four roller type rolling contact fatigue tester. Tangential traction and surface roughness of the harder mating rollers were varied and their effect was studied. The results indicate that the fatigue life decreases when fraction is applied in the same direction as that of rolling. When the direction of fraction is reversed, the life increases over that obtained with zero traction. The roughness of harder mating roller also has a marked influence on life. The smoother the mating roller, the longer the life. Microscopic observation of specimens revealed that the initiation of cracks during the early stages of life is more strongly influenced by the surface roughness, while the propagation of these cracks in the latter stages is affected mainly by the tangential traction.

Soda, N.↗
DOE OSTI2015

Experimental investigation on the electrical contact behavior of rolling contact connector

Rolling contact connector (RCC) is a new technology utilized in high performance electric power transfer systems with one or more rotating interfaces, such as radars, satellites, wind generators, and medical computed tomography machines. Rolling contact components are used in the RCC instead of traditional sliding contacts to transfer electrical power and/or signal. Since the requirement of the power transmission is increasing in these years, the rolling electrical contact characteristics become more and more important for the long-life design of RCC. In this paper, a typical form of RCC is presented. A series of experimental work are carried out to investigate the rolling electrical contact characteristics during its lifetime. The influence of a variety of factors on the electrical contact degradation behavior of RCC is analyzed under both vacuum and air environment. Based on the surface morphology and elemental composition changes in the contact zone, which are assessed by field emission scanning electron microscope and confocal laser scanning microscope, the mechanism of rolling electrical contact degradation is discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1982

Rolling-element fatigue life with traction fluids and automatic transmission fluid in a high-speed rolling-contact rig

Rolling-element fatigue tests were run in standard and high-speed rolling-contact rigs at bar speeds from 5000 to 50,000 rpm to determine the effects of speed and lubricant film parameter on rolling-element fatigue life. AISI 52100 test bars were tested at a maximum Hertz stress of 4.83 GPa (700,000 psi) with three traction fluids and an automatic transmission fluid. Rolling-element fatigue life increased with speed, with the greatest increases occurring from 10,000 to 50,000 rpm. The life data tended to follow published life-versus-lubricant-film-parameter data up to a film parameter of approximately 3.

Parker, R. J.↗
NASA NTRS1957

Effect of Fiber Orientation on Ball Failures Under Rolling-contact Conditions

The rolling-contact fatigue spin rig was used to test bails of a bearing steel at maximum Hertz stresses of 600,000 to 750,000 psi. The effect of fiber orientation was observed with the ball track restricted to passing directly over the poles, coincident with the equator, or randomly around the ball. The polar areas were found to be weaker in fatigue than the nonpolar areas. This resulted in a much greater portion of the failures occurring in the polar areas than would be expected from a homogeneous material. The early failures are discussed.

MATERIALS, PROPERTIES - FATIGUE↗
DOE OSTI2019

New Functionality of Ionic Liquids as Lubricant Additives: Mitigating Rolling Contact Fatigue

Oil-soluble ionic liquids (ILs) have recently been demonstrated as effective lubricant additives of friction reduction and wear protection for sliding contacts. However, their functionality in mitigating rolling contact fatigue (RCF) is little known. Because of the distinct surface damage modes, different types of surface protective additives often are used in lubricants for sliding and rolling contacts. Therefore, the lubricating characteristics and mechanisms of ILs learned in sliding contacts from the earlier work may not be translatable to rolling contacts. This study explores the feasibility of using phosphonium-phosphate, ammonium-phosphate, and phosphonium-carboxylate ILs as candidate additives in rolling–sliding boundary lubrication, and results suggested that an IL could be either beneficial or detrimental on RCF depending on its chemistry. Particularly, the best-performing phosphonium-phosphate IL at 2% addition made a low-viscosity base oil significantly outperform a more viscous commercial gear oil in reducing the RCF surface damage and associated vibration noise. This IL generated a thicker, smoother, and more homogeneous tribofilm compared with commercial additives, which is likely responsible for the superior RCF protection. Results here suggest good potential for using appropriate IL additives to allow the use of low-viscosity gear and axle fluids for improved efficiency and durability.

36 MATERIALS SCIENCE↗
NASA NTRS1957

Stress-life relation of the rolling-contact fatigue spin rig

The rolling-contact fatigue spin rig was used to test groups of SAE 52100 9.16-inch-diameter balls lubricated with a mineral oil at 600,000-, 675,000-, and 750,000-psi maximum Hertz stress. Cylinders of AISI M-1 vacuum and commercial melts and MV-1 (AISI M-50) were used as race specimens. Stress-life exponents produced agree closely with values accepted in industry. The type of failure obtained in the spin rig was similar to the subsurface fatigue spells found in bearings.

SURFACES, CONTACT - ROLLING↗
NASA NTRS1989

Surface fatigue life of carburized and hardened M50NiL and AISI 9310 spur gears and rolling-contact test bars

Spur gear endurance tests and rolling-element surface tests were conducted to investigate vacuum-induction-melted, vacuum-arc-melted (VIM-VAR) M50NiL steel for use as a gear steel in advanced aircraft applications, to determine its endurance characteristics, and to compare the results with those for standard VAR and VIM-VAR AISI 9310 gear material. Tests were conducted with spur gears and rolling-contact bars manufactured from VIM-VAR M50NiL and VAR and VIM-VAR AISI 9310. The gear pitch diameter was 8.9 cm (3.5 in.). Gear test conditions were an inlet oil temperature of 320 K (116 F), and outlet oil temperature of 350 K (170 F), a maximum Hertz stress of 1.71 GPa (248 ksi), and a speed of 10,000 rpm. Bench rolling-element fatigue tests were conducted at ambient temperatures with a bar speed of 12,500 rpm and a maximum Hertz stress of 4.83 GPA (700 ksi). The VIM-VAR M50NiL gears had a surface fatigue life that was 4.5 and 11.5 times that for VIM-VAR and VAR AISI 9310 gears, respectively. The surface fatigue life of the VIM-VAR M50NiL rolling-contact bars was 13.2 and 21.6 times that for the VIM-VAR and VAR AISI 9310, respectively. The VIM-VAR M50NiL material was shown to have good resistance to fracture through a fatigue spall and to have fatigue life far superior to that of both VIM-VAR and VAR AISI 9310 gears and rolling-contact bars.

Townsend, Dennis P.↗
NASA NTRS1989

Surface fatigue life of carburized and hardened M50NiL and AISI 9310 spur gears and rolling-contact test bars

Spur gear endurance tests and rolling-element surface tests were conducted to investigate vacuum-induction-melted, vacuum-arc-melted (VIM-VAR) M50NiL steel for use as a gear steel in advanced aircraft applications, to determine its endurance characteristics, and to compare the results with those for standard VAR and VIM-VAR AISI 9310 gear material. Tests were conducted with spur gears and rolling-contact bars manufactured from VIM-VAR M50NiL and VAR and VIM-VAR AISI 9310. The gear pitch diameter was 8.9 cm (3.5 in.). Gear test conditions were an inlet oil temperature of 320 K (116 F), and outlet oil temperature of 350 K (170 F), a maximum Hertz stress of 1.71 GPa (248 ksi), and a speed of 10,000 rpm. Bench rolling-element fatigue tests were conducted at ambient temperatures with a bar speed of 12,500 rpm and a maximum Hertz stress of 4.83 GPA (700 ksi). The VIM-VAR M50NiL gears had a surface fatigue life that was 4.5 and 11.5 times that for VIM-VAR and VAR AISI 9310 gears, respectively. The surface fatigue life of the VIM-VAR M50NiL rolling-contact bars was 13.2 and 21.6 times that for the VIM-VAR and VAR AISI 9310, respectively. The VIM-VAR M50NiL material was shown to have good resistance to fracture through a fatigue spall and to have fatigue life far superior to that of both VIM-VAR and VAR AISI 9310 gears and rolling-contact bars.

Townsend, Dennis P.↗
NASA NTRS1976

Rolling-contact deformation of MgO single crystals

Magnesium oxide single crystals were used as a model bearing material and deformed by rolling contact with a steel ball 0.64 cm in diameter. A dependence of depth of slip on rolling velocity which persisted with increasing numbers of rolling-contact cycles was discovered. The track width, track hardness and dislocation interactions as observed by transmission electron microscopy all increased in a consistent manner with increasing cycles. The rolling-contact state of stress produces a high density of dislocations in a localized zone. Dislocation interaction in this zone produces cleavage-type cracks after a large number of rolling-contact cycles. The orientation of the crystal influences the character of dislocation accumulation.

Dufrane, K. F.↗
NASA NTRS1993

A study of subsurface crack initiation produced by rolling contact fatigue

Results of subsurface crack initiation studies produced by pure rolling contact fatigue in 7075-T6 aluminum alloy are presented in this article. Microstructural changes and subsequent crack initiation below the contacting surface in cylindrical test specimens subjected to repeated rolling contact are illustrated. The rolling conditions are simulated in a three-dimensional elastic-plastic finite element model in order to estimate the plastic strains and residual stresses in the test material. The numerically estimated distribution of plastic strains in the model correlate well with the extent of microstructural changes observed in the test specimen. Results also indicate that a combination of plastic strains and low values of residual stresses is conducive to subsurface crack initiation and growth.

Kumar, Arun M.↗
NASA NTRS1957

Preliminary metallographic studies of ball fatigue under rolling-contact conditions

The metallurgical results produced on balls tested in the rolling-contact fatigue spin rig were studied by metallographic examination. Origin and progression of fatigue failures were observed. These evaluations were made on SAE 52100 and AISI M-1 balls fatigue tested at room temperature (80 F) and 200 to 250 F. Most failures originated subsurface in shear; inclusions, structure changes, and directionalism adversely affected ball fatigue life. Structures in the maximum-shear-stress region of the balls of both materials were stable at room temperature and unstable at 200 to 250 F. Failures were of the same type as those found in full-scale bearings.

SURFACES, CONTACT - ROLLING↗
NASA NTRS1985

Rolling-Contact Rheostat

Contact noise in rheostats and potentiometers reduced by rolling contact design. Smooth rolling action eliminates sporadic variations in resistance caused by bouncing and stick/slip motion of conventional sliding contacts.

Ruoff, C. F.↗
NASA NTRS1987

Mechanisms of rolling contact spalling

The results of a study aimed at analyzing the mechanical material interactions responsible for rolling contact spalling of the 440 C steel, high pressure oxygen turbopump bearings are presented. A coupled temperature displacement finite element analysis of the effects of friction heating under the contact is presented. The contact is modelled as a stationary, heat generating, 2 dimensional indent in an elastic perfectly plastic half-space with heat fluxes up to 8.6 x 10000 KW/m sq comparable to those generated in the bearing. Local temperatures in excess of 1000 C are treated. The calculations reveal high levels of residual tension after the contact is unloaded and cools. Efforts to promote Mode 2/Mode 3 fatigue crack growth under cyclic torsion in hardened 440 C steel are described. Spalls produced on 440 C steel by a 3 ball/rod rolling contact testing machine were studied with scanning microscopy. The shapes of the cyclic, stress strain hysteresis loops displayed by hardened 440 C steel in cyclic torsion at room temperature are defined for the plastic strain amplitudes encountered in rolling/sliding contact. Results of these analyses are discussed in detail.

Kumar, A. M.↗