Search NASA⌕ Search

SEARCH · Search NASA

Results for “RON”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Effects of knock intensity measurement technique and fuel chemical composition on the research octane number (RON) of FACE gasolines: Part 2 – Effects of spark timing

The Research and Motor Octane Number (RON, MON) characterize a fuel’s knock resistance by rating the knock intensity of a sample fuel relative to that of Primary Reference Fuels (PRF) in a Cooperative Fuel Research (CFR) Engine. A fuel’s octane number is regulated to prevent damage from autoignition leading to knocking combustion in spark-ignition engines. The operational differences between the standard RON rating and modern engine operation are explored in a three-part publication series. The previous study focused on the effects of lambda and knock characterization. This second study primarily focuses on the effects of spark timing on RON determination. Following the findings from the first publication, the knock intensity was captured by the knockmeter and by the maximum amplitude of pressure oscillations (MAPO) at the lambda of peak knock intensity and stoichiometry. Knock-limited spark advance tests were conducted for a set of seven Fuels for Advanced Combustion Engines (FACE) from the Coordinating Research Council (CRC) with varying chemical composition, PRFs, and Toluene Standardization Fuels (TSFs). For retarded spark timings, pre-spark low-temperature heat release was found for low RON PRFs. Low RON PRFs also showed knocking characteristics before reaching the center of combustion suggesting that the use of knock-limited spark advance (KLSA) was preferred over the knock-limited combustion phasing. Primarily paraffinic fuels tended towards increased pressure oscillations while dominantly aromatic fuels experienced higher pressure rise rates. A MAPO-based KLSA correlated best to Octane Index at a negative K-factor suggesting beyond RON operation despite being at otherwise RON conditions. At stoichiometry, the MAPO-based KLSA did neither correlate to RON nor Octane Index. Finally, good agreement was found between KLSA-based effective RON from this study to the MAPO-based effective RON from the first study.

10 SYNTHETIC FUELS↗

A 100+ RON Gasoline Blendstock for High Efficiency, Low Emission Vehicles Engines - CRADA 493 (Final Report)

This study aimed at demonstrating production of a 100+RON gasoline fraction from a linear olefins feedstock to help improve further the viability and flexibility of the Pacific Northwest National Laboratory/ LanzaTech alcohol-to-jet (ATJ) patented process that converts ethanol from LanzaTech’s syngas fermentation process to low aromatic jet-range iso-paraffins. To achieve a high RON gasoline and ultimately a 100+RON, the technical approach consisted of converting the linear olefins into an iso-olefins rich mixture and then oligomerizing the iso-olefins rich mixture into high RON compounds in a single bed loaded with an acid catalyst that allows conversion at low reaction temperature. Three families of acid catalysts labeled as type A, B and C were investigated for the single-bed conversion of linear olefins into high RON gasoline range compounds. The effects of the nature of the catalyst, acid sites concentration and operating conditions were investigated. Fuel properties measurements and engine testing were conducted for the most promising catalyst. For type A catalysts, we demonstrated that the conversion increases with the increase of the Brönsted acid site concentration and that lower reaction temperature favors the formation of desired highly branched compounds. The highest dRON obtained with type A catalyst was equal to 94 (from NMR and IQT). Type B catalysts appear very effective for producing dimethyl-olefins compounds when operating at low reaction temperature (i.e., < 100°C). The highest dRON obtained with type B catalyst was equal to 92. The results suggest that type B catalysts are less favorable to internal conversion of linear olefins into iso-olefins compared to type A catalysts which leads to the formation of a gasoline blendstock with a lower dRON. A Type C catalyst that is less commonly used for production of gasoline range compounds from linear olefins was investigated due to its ability to favor conversion of linear olefins into iso-olefins. Compared to type A and type B catalyst, type C favors the formation of highly branched compounds (i.e., with 3+ methyl groups) in the gasoline range. Indeed, a gasoline blendstock containing about 33 wt.% of highly branched compounds was produced with type C catalyst while maintaining a high linear olefins conversion (i.e., 70%). A large quantity of this gasoline blendstock was produced and fuel properties measurements including engine testing for Research Octane Number (RON), Motor Octane Number (MON) and octane sensitivity (S) were conducted. A high RON = 97, MON = 82.7, S =14.3, AKI = 90 and HoV = 334.1kJ/kg were measured. While a RON of 100 was not achieved, the fuel properties of the gasoline blendstock are very acceptable as compared to current premium gasoline. Overall, these results highlight the potential for producing a high RON/ premium gasoline blendstock starting from a linear olefins feedstock.

02 PETROLEUM↗

Combustion Characteristics of PRF and TSF Ethanol Blends with RON 98 in an Instrumented CFR Engine

The CFR F1 engine is the standard testing apparatus used for rating the research octane number (RON) of gasoline fuels. Unlike the motor octane number (MON) method, where the intake port temperature after the carburetor is controlled by an electric heater, the mixture temperature can vary during the RON test due to the heat of vaporization (HoV) of the fuel. Ethanol is receiving increasing attention as a high octane and high HoV fuel component. This work presents an analysis of the combustion characteristics during the RON rating of ethanol fuel blends according to the standard ASTM D2699 method, highlighting the effects of ethanol concentration and base fuel composition. All fuels were blended to a constant RON of 98. Ethanol levels varied from 0 to 50 vol% and the base fuels were surrogate blends composed of primary reference fuels (PRF), toluene standardization fuels (TSF), and a four component gasoline surrogate. These were compared against two full boiling range gasolines, also having a RON of 98. Through the use of detailed cylinder pressure analyses, this paper provides insights into the combustion behavior of various RON 98 fuels which are commonly not captured by the standard RON knock rating method. Ethanol was found to significantly reduce the pressure transducer based knock intensity of PRF fuel blends up to a level of 30 vol%, despite all fuels having the same RON. Meanwhile, the knock intensity of the equivalent TSF fuel blends was found to be relatively insensitive to ethanol concentration. For ethanol concentrations beyond 30 vol%, the pressure transducer based knock intensity behavior did not appear to be affected by the base fuel composition.

CFR↗

Effects of knock intensity measurement technique and fuel chemical composition on the research octane number (RON) of FACE gasolines: Part 1 – Lambda and knock characterization

The Research and Motor Octane Number (RON and MON) rate the knock propensity of gasoline in the Cooperative Fuel Research (CFR) engine by comparing the knock intensity of sample fuels relative to that of primary reference fuels (PRF), a binary blend of iso-octane and n-heptane. Important differences exist between standard octane testing and automotive spark ignition (SI) engine knock testing including speed, load, air-to-fuel equivalence ratio (lambda), and knock characterization, which lead to a discrepancy between a fuel’s RON rating and its knock resistance characterized on an automotive SI engine based on knock-limited spark advance. This publication is the first of a set of three publications which modify operating parameters of the RON test method (ASTM D2699) to investigate the effects of these differences with automotive SI engine knock-limited spark advance testing. A fuel’s standard RON is evaluated at the lambda of the highest knock intensity, whereas automotive SI engines typically operate at stoichiometry. Here, we analyze the effects of a stoichiometric RON rating methodology. Additionally, the knock intensity response from the standard CFR knockmeter system is compared to a cylinder pressure oscillation-based knock intensity at several lambda settings. All experiments were performed with a set of seven Coordinating Research Council (CRC) Fuels for Advanced Combustion Engines (FACE) gasolines with approximately 95 RON. The fuel chemical composition impacted the lambda of the highest knock intensity, which resulted in fuel-specific offsets between the standard and stoichiometric RON ratings. The knock system comparison showed significant offsets between cylinder pressure-based and knockmeter-based knock intensity levels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A new chemical kinetic method of determining RON and MON values for single component and multicomponent mixtures of engine fuels

A new method of using chemical kinetic reaction modeling to predict the Research Octane Number (RON) and Motor Octane Number (MON) of single component fuels and fuel mixtures is described and illustrated via comparisons between computed and experimental values obtained using the well-established ASTM test procedures in a Cooperative Fuels Research (CFR) engine. Comparisons include predictions of RON and MON for a large variety of neat fuels, studies determining the RON and MON of mixtures of primary reference fuels (PRF) and toluene, and studies of RON and MON for mixtures of single-component and multiple-component gasoline surrogate mixtures with ethanol. Advantages in costs, time, and experimental complexity of the kinetic modeling approach compared to the existing engine test procedures are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

100+ RON Gasoline Blendstock for High Efficiency, Low Emissions (CRADA 493)

The PNNL/LanzaTech alcohol-to-Jet (ATJ) patented process converts ethanol from LanzaTech’s syngas fermentation process to low aromatic jet-range isoparaffins. Compounds are generated across a wide boiling range by the process. The project goal is to improve the viability of the ATJ process by increasing the RON of the gasoline fraction and determine what types of engines and vehicles can be fueled with this gasoline. PNNL experts’ team will investigate the impact of the process conditions and catalysts formulation on the blendstock composition in relation with the fuel properties. Co-optima capabilities for fuel properties measurements will be leveraged to assess the potential engines/ vehicles applications of the produced blendstock. A techno-economic-analysis will be conducted to assess the commercial viability of the process for generating a high RON gasoline-range fuel.

09 BIOMASS FUELS↗

Apollo, Paintbrushes, and Packaging: An Interview with 40-Year Spacesuit Veteran Ron Woods

Ron Woods exhibits a wealth of knowledge gathered in more than 40 years of experience with NASA and spacesuits. Many people are interested in his biography, progression of work at NASA, impact on the U.S. Spacesuit, and career accomplishments. Wright, from the JSC History Office, conducted this personal background interview with Woods. The interview highlighted the influences and decision-making methods that impacted his technical and management contributions to the space program.

Woods, Ron↗

In Conversation With Materials Scientist Ron Zuckermann

Nov. 11, 2009: Host Alice Egan of Berkeley Lab's Materials Sciences Division interviews scientists about their lives and work in language everyone can understand. Her guest Berkeley Lab's Ron Zuckermann, who discusses biological nanostructures and the world of peptoids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fuel-air mixing in motored CFR engine at research octane number (RON) relevant condition

This paper presents a three-dimensional (3-D) computational fluid dynamics (CFD) study of a motored cooperative fuel research (CFR) engine at research octane number (RON) relevant condition. The boundary conditions for 3-D simulations were generated with a one-dimensional GT-Power model. For the first time in literature, a carburetor was added to a virtual CFR engine model with 3-D CFD. Therefore, the proposed setup can simulate the fuel and thermal stratifications inside the engine cylinder with realistic detail. The transient simulations in this work were performed within the Reynolds-averaged Navier-Stokes (RANS) framework with a Realizable k-ε turbulence model. Major conclusions from the present work are: (1) The in-cylinder flow of the CFR engine is swirl-dominated due to the existence of the intake valve shroud. (2) There is a significant amount of liquid droplets entering the cylinder during the intake stroke. The maximum instantaneous amount of liquid for 50% PRF 87 (containing 87% iso-octane and 13% n-heptane (v/v)) and 50% ethanol mixture is indicated to be around 26% of total injected fuel mass. (3) The heat of vaporization (HoV) of the fuel is responsible for creating both temperature and charge stratification inside the cylinder.

33 ADVANCED PROPULSION SYSTEMS↗