Search NASA⌕ Search

SEARCH · Search NASA

Results for “Radio Transmission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Automatic radio-transmission monitor

System continuously monitors radio transmissions stored in memory. If spectrum deviates beyond present limits, alarm is tripped and spectrum is transferred to long-term storage for later analysis. Monitor can be useful in ensuring proper power level and spectral quality and in finding cause of failure. It might also be used to monitor radio-frequency interference or power levels of citizen's-band transmitters.

Bernstein, A. J.↗
NASA NTRS1987

Upward streamers produced by a lightning strike to radio transmission towers

A lightning strike to the center of three 78-m radio transmission towers produced upward discharges with lengths of 40 and 79 m from each of the neighboring towers. This strike also caused a number of insulators on guy wires that supported the tower to flash over, and the locations of these points and the two-dimensional geometry of the discharge channels are projected onto a vertical plane that is centered on the tower.

Krider, E. Philip↗
NASA NTRS1961

Experiments with Plasmas Produced by Potassium-Seeded Cyanogen Oxygen Flames for Study of Radio Transmission at Simulated Reentry Vehicle Plasma Conditions

A method for the chemical production of an ionized gas stream for application to radio transmission studies is described. Involved is the combustion of gaseous cyanogen and oxygen with the addition of vaporized potassium in some cases to further increase the ionization. Experiments are described in which a 3-inch-diameter subsonic free jet at atmospheric pressure is used, and the results are presented. The plasma obtained by using this method is sufficient to simulate plasma conditions expected for reentering hypersonic vehicles. The unseeded plasma stream temperature is indicated to be about 4,200 K, with the degree of ionization indicated to be that expected from thermal equilibrium considerations. Measurements of radio-signal loss due to the unseeded flame plasma are presented for microwaves of 8 to 20 kmc transmitted through the stream and for a dipole transmitting model of 219.5 mc immersed in the stream. Favorable comparison of these results with the simple plane-wave signal-attenuation theory was obtained. In the case of a 9.4-kmc microwave signal of 30-kw peak power, the preliminary indication is that the plasma characteristics were not changed due to this strong signal. Comparison of a simplified concept of radio-signal attenuation due to plasmas is made with some hypersonic reentry vehicle signal-loss data. Other areas of plasma research using this method for the transmission problem are indicated.

Huber, Paul W.↗
NASA NTRS1972

Postflight analysis of the EVCS-LM communications link for the Apollo 15 mission

Data from the Apollo 15 mission were used to compare the actual performance of the EVCS to LM communications link with the preflight performance predictions. Based on the results of the analysis, the following conclusions were made: (1) The radio transmission loss data show good correlation with predictions during periods when the radio line of sight was obscured. (2) The technique of predicting shadow losses due to obstacles in the radio line of sight provides a good estimate of the actual shadowing loss. (3) When the transmitter was on an upslope, the radio transmission loss approached the free space loss values as the line of sight to the LM was regained.

Royston, C. L., Jr.↗
NASA NTRS1970

Thermal performance and radio-frequency transmissivity of candidate ablation materials for S-band antenna window application on manned spacecraft

A test program was conducted in the MSC 1.5 MW arc-heated facility to evaluate the thermal performance of ablation materials having potential application as radio frequency windows. These tests were conducted for the improvement of omnidirectional antenna operating characteristics during atmospheric reentry. Since a full scale model of the Apollo command service module was available for antenna tests, this mockup was used as a basic for the tests. Test models were subjected to heating conditions simulating the nominal lunar return trajectory (AS-501) and the design trajectories, high heat load and high heating rate. RF measurements were made before and after the arc jet tests to measure attenuation effects due to the thermal degradation of the materials under consideration. The test program demonstrated that additional development is required in materials technology to achieve an ablative system with both good RF transmission characteristics and thermal-structural integrity.

Tillian, D. J.↗
NASA NTRS1986

VEGA balloon system and instrumentation

The VEGA Venus balloon radio transmissions received on earth were used to measure the motion of the balloons and to obtain the data recorded by onboard sensors measuring atmospheric characteristics. Thus the balloons themselves, the gondolas, the onboard sensors, and the radio transmission system were all components of the experiment. A description of these elements is given, and a few details of data sampling and formatting are discussed.

Kremnev, R. S.↗
NASA NTRS1984

Project Explorer: Get Away Special #007

Tentatively scheduled to fly on STS-17 (41G), this get away special aims to demonstrate amateur radio transmissions to global ground stations in the English language. Experiments No. 1, 2, and 3 use the micro-gravity of space flight to study the solidification of lead-antimony and aluminum-copper alloys, the germination of radish seeds, and the growth of potassium-tetracyanoplatinate hydrate crystals in an aqueous solution. Flight results are to be compared with Earth-based data. Experiment No. 4 (the Marshall Amateur Radio Club Experiment - MARCE) features radio transmissions and also provides timing for the start of all other experiments. A microprocessor obtains real-time data from all experiments as well as temperature and pressure measurements within the GAS canister. These data are to be transmitted on previously announced amateur radio frequencies after they are converted into the English language by a digitalker for general reception. The support structure for the G #007 experiments consists of two primary plates and four bumper assemblies.

Henderson, A. J., Jr.↗
NASA NTRS2013

Data Transfer for Multiple Sensor Networks Over a Broad Temperature Range

At extreme temperatures, cryogenic and over 300 C, few electronic components are available to support intelligent data transfer over a common, linear combining medium. This innovation allows many sensors to operate on the same wire bus (or on the same airwaves or optical channel: any linearly combining medium), transmitting simultaneously, but individually recoverable at a node in a cooler part of the test area. This innovation has been demonstrated using room-temperature silicon microcircuits as proxy. The microcircuits have analog functionality comparable to componentry designed using silicon carbide. Given a common, linearly combining medium, multiple sending units may transmit information simultaneously. A listening node, using various techniques, can pick out the signal from a single sender, if it has unique qualities, e.g. a voice. The problem being solved is commonly referred to as the cocktail party problem. The human brain uses the cocktail party effect when it is able to recognize and follow a single conversation in a party full of talkers and other noise sources. High-temperature sensors have been used in silicon carbide electronic oscillator circuits. The frequency of the oscillator changes as a function of the changes in the sensed parameter, such as pressure. This change is analogous to changes in the pitch of a person s voice. The output of this oscillator and many others may be superimposed onto a single medium. This medium may be the power lines supplying current to the sensors, a third wire dedicated to data transmission, the airwaves through radio transmission, an optical medium, etc. However, with nothing to distinguish the identities of each source that is, the source separation this system is useless. Using digital electronic functions, unique codes or patterns are created and used to modulate the output of the sensor.

Krasowski, Michael↗