Search NASA⌕ Search

SEARCH · Search NASA

Results for “Refabricator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Advanced Autonomous Welding for Refabrication and Follow-On Testing of Previously Irradiated Nuclear Fuel

The performance of follow-on experiments using irradiated nuclear fuel at any point in its lifecycle is a critical step in understanding phenomena and behavior. Transient experiments with high-burnup fuel can deepen the understanding of fuel fragmentation, relocations, and dispersal under loss-of-coolant accidents. An advanced autonomous welding process to refabricate commercial fuel rods inside a hot cell was created and tested to enable flexible experiment approaches on fuels irradiated in commercial and test reactors. Irradiated light water reactor fuel test pins from experiments performed at the Advanced Test Reactor (ATR) at Idaho National Laboratory were used to demonstrate the refabrication process. The welding process was found to be sensitive to welding parameters but flexible such that multiple passes could be performed on the same location until a hermetic weld was obtained. The refabrication of rodlets and successful welds was also found to be sensitive to the preparation of the irradiated cladding and endcaps. Thorough defueling of the fuel at the weld location and proper sizing of the endcaps and backing material mitigated these issues. The use of strategically located heat sinks in contact with the cladding and endcap materials also increased welding and refabrication success. For this work, the test pins were sectioned to remove the original endcaps and fuel was removed from both ends of each rodlet. The reassembly of the rodlets was then completed in four steps, which included the press fitting of new endcaps, the circumferential welding of rodlet endcaps to the cladding, rodlet pressurization in a pressure chamber, and seal welding the rodlet under pressure. The integrity of the refabricated rodlets was then verified via helium leak checking inside a vacuum chamber. The advanced welding system is capable of refabricating rodlets up to 380 mm in length, and repressurizing them up to 15 500 kPa. The refabricated lengths of the rodlets used in this work ranged from 149 to 165 mm and the refabricated fuel stack heights ranged from 70.4 to 79.8 mm. Here, the rodlets were pressurized with argon to an average pressure of 3617 kPa, and the average leak rate after refabrication was 6.7 • 10 -8 cm 3 • s -1 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Refabrication of HERA-HBU-1

Refabrication of a commercially irradiated fuel segment has been completed for the HERA-HBU-1 experiment. This presentation recounts the refabrication process, and the results of performing refabrication in preparation for the HERA-HBU-1 experiment.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Fuel Refabrication Prototype - Presentation for 2021 ASI Annual Webinar

This power point presentation is a summary of the work produced in FY2021 under the LWR Fuel Reinstrumentation project funded by DOE's Advanced Sensor Initiative, and the outlook for FY22. The objective of this portion of the ASI program is to "Capture critical technology created by the Institute For Energy (formerly Halden Reactor Project) to reinstrument irradiated fuel rodlets, and further this technology to enable incorporation of advanced instrumentation: fiberoptics, LVDTs, ultrasonic based sensors". The presentation explains that two of the three equipment modules were received and INL and a number of practice runs were conducted with them. In FY22 the third equipment module will arrive and using the three equipment modules measurement sciences personnel will create a complete prototypical instrumented fuel rodlet (using ceramic surrogates in the place of UO2).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

FY2022 Progress Report for Advanced Re-fabrication/Re-instrumentation Capability Development

In support of performing follow-on irradiation experiments with previously irradiated materials, the Halden Reactor Project developed unique and state of the art capabilities to refabricate and re-instrument previously irradiated materials. Such materials were used in in-pile tests at the Halden reactor, and out-of-pile tests for example using furnaces as a heat source. The decision to close the Halden Reactor Project results in the loss of this refabrication and re-instrumentation capability. As a result, the United States (U.S.) Department of Energy (DOE) has determined to develop refabrication and re-instrumentation capability at the unique shielded facilities at Idaho National Laboratory (INL). The development of refabrication capability has been completed and demonstrated. This report focuses on the complementary aspects of reinstrumentation and the progress to-date. Halden spent nearly 30 years developing both refabrication and re-instrumentation. Collaboration with Halden is allowing Idaho National Laboratory (INL) to develop this capability much more rapidly. In FY-21 the results include development of the capability to drill annular center holes in ceramic UO2 fuel pellets, development of fuel rod end caps with feedthroughs for centerline instrumentation inside the rodlet, The procurement of both fuel drilling and welding demonstration equipment from Halden, evaluation of surface thermocouple attachments to support better understanding of temperature measurement uncertainties, and finally, the conceptual design of a new shielded enclosure where advanced refabrication and re-instrumentation equipment can be housed. In FY-22, the results include; Completing set up of the drilling and welding modules procured from Halden, and early experimental trials using that equipment.; Completing set up of an out-of-cell circumferential weld system to allow for further weld development to take place and support fabrication of fuel for fresh fuel experiments.; Evaluation of the Hot Fuel Examination Facility (HFEF) infrastructure to support future installation of advanced re-fabrication/re-instrumentation equipment, specifically related to necessary infrastructure for cryo-drilling.; Developments in dry-drilling alternative. Including experimental studies showing cordierite is the most suitable surrogate for UO 2 for performing drilling studies. That drilling performance is enhanced when a fuel-clad bonding condition is simulated.; Conceptual design completed for attaching surface thermocouples to irradiated fuel in support of TWIST capsule experiments. The authors would like to thank the numerous colleagues at INL and Halden who provided support in accomplishing this work. Their support both material and intellectual is invaluable in advancing the state of the art and establishing the capabilities for refabrication and re-instrumentation at INL.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

FY21 Progress Report for Advanced Re fabrication/Re-instrumentation Capability Development

In support of performing follow on irradiation experiments with previously irradiated materials, the Halden Reactor Project developed unique and state of the art capabilities to refabricate and re-instrument previously irradiated materials. Such materials were used in in-pile tests at the Halden reactor, and out-of-pile tests for example using furnaces as a heat source. The decision to close the Halden Reactor Project results in the loss of this refabrication and reinstrumentation capability. As a result, the United States Department of Energy has determined to develop refabrication and re-instrumentation capability at the unique shielded facilities at Idaho National Laboratory. The development of refabrication capability has been completed and demonstrated. This report focuses on the complementary aspects of re-instrumentation and the progress to date. Halden spent nearly 30 years developing both refabrication and reinstrumentation. Collaboration with Halden is allowing INL to develop this capability much more rapidly. The results include development of the capability to drill annular center holes in ceramic UO2 fuel pellets, development of fuel rod end caps with feedthroughs for centerline instrumentation inside the rodlet, The procurement of both fuel drilling and welding demonstration equipment from Halden, evaluation of surface thermocouple attachments to support better understanding of temperature measurement uncertainties, and finally, the conceptual design of a new shielded enclosure where advanced refabrication and re-instrumentation equipment can be housed. The authors would like to thank the numerous colleagues at INL and Halden who provided support in accomplishing this work. Their support both material and intellectual is invaluable in advancing the state of the art and establishing the capabilities for refabrication and re-instrumentation at INL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Completion of Milestone M3CT-21IN0702028 - Receive Welding Module from IFE (Halden, Norway)

Prior to 2018, the U.S. DOE and the commercial nuclear industry relied upon the Halden Reactor Project’s capability to refabricate and reinstrument previously irradiated fuel rods. This capability has now been lost. This activity is key to recovering that capability and enabling the continuation of critical research on commercial and advanced LWR fuels. This welding module completes the three-module suite the Institute For Energy (IFE) was contracted to deliver to INL. This equipment will be used in FY22 to practice techniques developed at IFE for refabricating and instrumenting prototypical fuel rods.

42 ENGINEERING↗
DOE OSTI2025

Refabriation of HERA-HBU-2, LOC-HBU-1, and LOC-HBU-2

The development of advanced fuels for Light Water Reactors (LWRs) is essential for improved fuel performance and safety, including performance margins, uprates, and higher burnup. Because available commercial LWR fuels often cannot be used in research reactors, the refabrication of preirradiated fuel is necessary to enable follow-on testing of these fuels for characterizing fuel behavior during steady and transient irradiations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Extreme γ –Ray Radiation Tolerance of Spectrometer–Grade CsPbBr 3 Perovskite Detectors

The perovskite compound CsPbBr 3 has recently been discovered as a promising room-temperature semiconductor radiation detector, offering an inexpensive and easy-to-manufacture alternative to the current benchmark material Cd 1–x Zn x Te (CZT). The performance of CsPbBr 3 sensors is evaluated under harsh conditions, such as high radiation doses often found in industrial settings and extreme radiation in space. Results show minimal degradation in detector performance after exposure to 1 Mrad of Co-60 gamma radiation, with no significant change to energy resolution or hole mobility and lifetime. Additionally, many of the devices are still functional after being exposed to a 10 Mrad dose over 3 days, and those that do not survive can still be refabricated into working detectors. Notably, these results suggest that the failure mode in these devices is likely related to the interface between the electrode and material and their reaction, or the electrode itself and not the material itself. Overall, the study suggests that CsPbBr 3 has high potential as a reliable and efficient radiation detector in various applications, including those involving extreme fluxes and energies of gamma-ray radiation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recycling lead and transparent conductors from perovskite solar modules

Abstract Perovskite photovoltaics are gaining increasing common ground to partner with or compete with silicon photovoltaics to reduce cost of solar energy. However, a cost-effective waste management for toxic lead (Pb), which might determine the fate of this technology, has not been developed yet. Here, we report an end-of-life material management for perovskite solar modules to recycle toxic lead and valuable transparent conductors to protect the environment and create dramatic economic benefits from recycled materials. Lead is separated from decommissioned modules by weakly acidic cation exchange resin, which could be released as soluble Pb(NO 3 ) 2 followed by precipitation as PbI 2 for reuse, with a recycling efficiency of 99.2%. Thermal delamination disassembles the encapsulated modules with intact transparent conductors and cover glasses. The refabricated devices based on recycled lead iodide and recycled transparent conductors show comparable performance as devices based on fresh raw materials. Cost analysis shows this recycling technology is economically attractive.

14 SOLAR ENERGY↗
DOE OSTI2026

Direct electrode-to-electrode regeneration of end-of-life batteries via electrode–electrolyte interphase dissolution

Lithium-ion battery recycling remains constrained by processes that recover metals at the expense of electrode integrity, while even direct recycling typically requires shredding to black mass followed by binder removal, separation, and full electrode refabrication. Here, we introduce direct electrode-to-electrode regeneration (DEER), a simultaneous electrochemical regeneration of used NMC and graphite electrodes from end-of-life batteries in their intact form by dissolving the passivating electrode–electrolyte interphase (EEI). DEER employs 1,3-dimethyl-2-imidazolidinone (DMI), a high donor number solvent that creates a thermodynamic environment favorable for solubilizing redox inactive EEI components. DEER dissolves the thick EEI on both used electrodes while preserving electrode integrity, enabling up to 95% capacity regain and improved cycling stability with a residual LiF-rich interphase. Operando Raman, operando IR, and post-mortem NMR directly track the electrochemically driven dissolution of carbonate-derived EEI species in the used DMI-based recycling electrolyte. Technoeconomic and life-cycle analyses show that DEER reduces the cost of recycled cell manufacturing by 56% relative to pyro- and hydrometallurgy, while lowering energy use and greenhouse gas emissions. Overall, DEER establishes the first validated pathway to directly regenerate and reuse electrodes harvested from truly end-of-life batteries, converting the key interfacial bottleneck into a controllable dissolution process and opening a practical route toward electrode level circularity.

Kim, Kiwon [Cornell Univ., Ithaca, NY (United Stat↗
DOE OSTI2022

OECD/NEA MPCMIV Benchmark - Preliminary fuel performance results

The on-going OECD/NEA Multi-physics Pellet Cladding Mechanical Interaction Validation (MPCMIV) benchmark aims to provide guidance on multi-physics validation through the modelling of two cold ramps. In this paper, the first results for the base irradiation of the father rod and fuel rodlet (refabricated from the father rod), and the first cold ramp are presented. The base irradiation consists of 3 years of irradiation in the Forsmark-2 reactor. The cold ramp encompasses a steady-state pre-ramp period of less than one hour at a low constant linear heat rate (LHR) followed by a ramp test (< 1 min) with a much higher maximal LHR. The base irradiation is modelled using the fuel performance codes FRAPCON and FAST, while the cold ramp modeling is using the fuel performance code FRAPTRAN. Several missing parameters for FRAPCON/FAST base irradiation models have been selected using multiple references such as the OECD/NEA light water reactor Uncertainty Analysis in Modelling (UAM) benchmark specifications and the FRAPCON Integral Assessment report. The obtained results for the base irradiation such as the cladding outer diameter show reasonable agreement with the experimental measurements. The results for the cold ramp show larger differences with the experimental measurements (e.g., cladding axial elongation). However, such differences have been observed as well in other studies involving pellet cladding mechanical interaction analyses and are attributed to the fuel performance modelling assumptions and to the tuned modelling parameters that were not covered by the specifications. Uncertainty and sensitivity analysis might allow a better quantification of these missing parameters. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

FUEL PERFORMANCE STUDIES AT IDAHO NATIONAL LABORATORY MAKING USE OF THE BYRON FUEL SHIPMENT

In December of 2023 a shipment of commercially irradiated fuel rods from the Byron Generating Station in Illinois was successfully shipped to the Materials and Fuels Complex (MFC) at Idaho National Laboratory (INL). The make-up of the rods includes a mix of cladding types from traditional ZirloTM, advanced zirconium alloys, and chrome coated ZirloTM. Burnups range from regular end of life values to over 70 GWd/MTU rod average. The R&D plan for the rods involves multiple projects from developing licensing data for new claddings to integral transient tests to support burnup extension efforts in the United States. The R&D began in early 2024 with the nondestructive examinations of the rods after which they will be sectioned for microscopy, mechanical testing, and analytical chemistry. Additionally, many rod segments will be refabricated into new test pins and inserted into a static water capsule for integral Reactivity Initiated Accident (RIA) and Loss of Coolant Accident (LOCA) testing at the TREAT reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗