Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reference flow sheet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Optimized Flow Sheet for a Reference Commercial-Scale Nuclear-Driven High-Temperature Electrolysis Hydrogen Production Plant

This report presents results from the development and optimization of a reference commercialscale high-temperature electrolysis (HTE) plant for hydrogen production. The reference plant design is driven by a high-temperature helium-cooled reactor coupled to a direct Brayton power cycle. The reference design reactor power is 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 540° C and 900°C, respectively. The electrolysis unit used to produce hydrogen consists of 4.176 × 10 6 cells with a per-cell active area of 225 cm2. A nominal cell area-specific resistance, ASR, value of 0.4 Ohm•cm2 with a current density of 0.25 A/cm2 was used, and isothermal boundary conditions were assumed. The optimized design for the reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes an air-sweep system to remove the excess oxygen that is evolved on the anode side of the electrolyzer. The inlet air for the air-sweep system is compressed to the system operating pressure of 5.0 MPa in a four-stage compressor with intercooling. The overall system thermal-to-hydrogen production efficiency (based on the low heating value of the produced hydrogen) is 49.07% at a hydrogen production rate of 2.45 kg/s with the high-temperature helium-cooled reactor concept. The information presented in this report is intended to establish an optimized design for the reference nuclear-driven HTE hydrogen production plant so that parameters can be compared with other hydrogen production methods and power cycles to evaluate relative performance characteristics and plant economics.

08 HYDROGEN↗

Considerations in the development of a process to manufacture low-enriched uranium foil fuel for the high flux isotope reactor

A reference flow sheet is the one of the first planning steps in the development of a manufacturing capacity for low enriched uranium foil fuels and can be used to develop a work structure, a critical path schedule and identify development needs. The reference flow sheet presented is specific to the High Flux Isotope Reactor and is used to estimate the change in HFIR operating cost due to fuel conversion. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Advanced Low Energy Enzyme Catalyzed Solvent for CO 2 Capture

A proof-of-concept biocatalyst enhanced solvent process was developed and demonstrated in an integrated bench-scale system using coal post combustion flue gas. The biocatalyst was deployed as a coating on M500X structured packing. Rate enhancement was evaluated using a non-volatile and non-toxic 20 wt% potassium carbonate solution. Greater than 500-fold volumetric scale-up from laboratory to bench scale was demonstrated in this project. Key technical achievements included: 10-fold mass transfer enhancement demonstrated in laboratory testing relative to blank potassium carbonate at 45°C; ~ 7-fold enhancement over blank in bench-scale field testing at National Carbon Capture Center; aerosol emissions were below detection limits (< 0.8 ppm); 90% capture was demonstrated at ~19.5 Nm 3 /hr (dry basis); and ~ 80% CO 2 capture was demonstrated at ~ 30 Nm 3 /hr (dry basis) for more than 2800-hrs on flue gas with minimal detectible decline in activity. The regeneration energy requirement was 3.5 GJ/t CO 2 for this solvent, which was below the target of <2.1 GJ/t CO 2 . Bench unit testing revealed kinetic limitations in the un-catalyzed stripper at around 85°C, but process modeling based on bench unit data showed that equivalent work of less than 300 kWh/t CO 2 including all CO 2 compression can be achieved at lower temperature stripping conditions. Cost analysis showed that 20% potassium carbonate in a basic solvent flow sheet with biocatalyst coated packing has economic performance comparable to the reference NETL Case-12, 30% MEA. A detailed techno-economic analysis indicated that addition of catalyst in the stripper could reduce the cost of capture by ~6% and cost of avoided CO 2 by ~10% below reference NETL Case-12. Based on these results, a directional plan was identified to reduce the cost of CO 2 capture in future work.

54 ENVIRONMENTAL SCIENCES↗

Thermal Integration of Advanced Nuclear Reactors with a Reference Refinery, Methanol Synthesis, and a Wood Pulp Plant (Rev.1)

The present report is intended to provide process flow diagrams (PFDs) and energy and mass balance data sheets for a U.S. industrial sector subset with which nuclear heat and power could be integrated—a subset that includes the oil refining, methanol and pulp and paper industries. Coupling options for integrating nuclear energy into these industries are quantitatively outlined for reference systems, and future work will extend this analysis in greater detail. Opportunities for integrating small modular nuclear reactors (SMNRs) were investigated for each of the industrial process configurations. Aspen HYSYS and Cycle-Tempo models for a high-temperature gas-cooled reactor were developed to evaluate the proposed integration. This introductory evaluation provides a general description and assessment of the operating principles, reactor coolant core outlet temperature, and reactor size to be integrated with industry. The industrial processes of oil refining and the production of methanol, pulp and paper were simulated by using Aspen HYSYS, Aspen Plus, and the PRELIM (Petroleum Refinery Life Cycle Inventory Model) tool to develop process details. Cycle-Tempo models then extend the process modeling results to obtain net energy demands (e.g., heat, steam, and electricity) when accounting for process steam and waste heat recovery. This information is intended to foster the analysis of integrating an SMNR to decarbonize industrial facilities. The SMNR would provide reliable, competitive, and sustainable clean energy while reducing carbon emissions and other environmental impacts, such as water withdrawals, consumption, and contamination. The refining industry, exhibited in Figure ES1, is a leading consumer of fossil -fuel-based heat, power, and hydrogen in the U.S. industrial sector, generating over 164 million metric tons (MMT) of CO 2 emissions in 2023. The overall mass and energy pertaining to a generalized complex refinery in the United States is reflected in Figure ES1, along with energy metrics regarding integration with a nuclear power plant (NPP). Data sheets were developed to indicate the energy requirements for the overall refinery and each refinery process. The data sheet for the overall refinery is shown in Table ES2.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Cavitation erosion prediction based on analysis of flow dynamics and impact load spectra

Cavitation erosion is the consequence of repeated collapse-induced high pressure-loads on a material surface. The present paper assesses the prediction of impact load spectra of cavitating flows, i.e., the rate and intensity distribution of collapse events based on a detailed analysis of flow dynamics. Data are obtained from a numerical simulation which employs a density-based finite volume method, taking into account the compressibility of both phases, and resolves collapse-induced pressure waves. To determine the spectrum of collapse events in the fluid domain, we detect and quantify the collapse of isolated vapor structures. As reference configuration we consider the expansion of a liquid into a radially divergent gap which exhibits unsteady sheet and cloud cavitation. Analysis of simulation data shows that global cavitation dynamics and dominant flow events are well resolved, even though the spatial resolution is too coarse to resolve individual vapor bubbles. The inviscid flow model recovers increasingly fine-scale vapor structures and collapses with increasing resolution. We demonstrate that frequency and intensity of these collapse events scale with grid resolution. Scaling laws based on two reference lengths are introduced for this purpose. We show that upon applying these laws impact load spectra recorded on experimental and numerical pressure sensors agree with each other. Furthermore, correlation between experimental pitting rates and collapse-event rates is found. Locations of high maximum wall pressures and high densities of collapse events near walls obtained numerically agree well with areas of erosion damage in the experiment. The investigation shows that impact load spectra of cavitating flows can be inferred from flow data that captures the main vapor structures and wave dynamics without the need for resolving all flow scales.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Self-similarity and scaling transitions during rupture of thin free films of Newtonian fluids

Rupture of thin liquid films is crucial in many industrial applications and nature such as foam stability in oil-gas separation units, coating flows, polymer processing, and tear films in the eye. In some of these situations, a liquid film may have two free surfaces (referred to here as a free film or a sheet) as opposed to a film deposited on a solid substrate that has one free surface. The rupture of such a free film or a sheet of a Newtonian fluid is analyzed under the competing influences of inertia, viscous stress, van der Waals pressure, and capillary pressure by solving a system of spatially one-dimensional evolution equations for film thickness and lateral velocity. The dynamics close to the space-time singularity where the film ruptures is asymptotically self-similar and, therefore, the problem is also analyzed by reducing the transient partial differential evolution equations to a corresponding set of ordinary differential equations in similarity space. Here, for sheets with negligible inertia, it is shown that the dominant balance of forces involves solely viscous and van der Waals forces, with capillary force remaining negligible throughout the thinning process in a viscous regime. On the other hand, for a sheet of an inviscid fluid for which the effect of viscosity is negligible, it is shown that the dominant balance of forces is between inertial, capillary, and van der Waals forces as the film evolves towards rupture in an inertial regime. Real fluids, however, have finite viscosity. Hence, for real fluids, it is further shown that the viscous and the inertial regimes are only transitory and can only describe the initial thinning dynamics of highly viscous and slightly viscous sheets, respectively. Moreover, regardless of the fluid’s viscosity, it is shown that for sheets that initially thin in either of these two regimes, their dynamics transition to a late stage or final inertial-viscous regime in which inertial, viscous, and van der Waals forces balance each other while capillary force remains negligible, in accordance with the results of Vaynblat, Lister, and Witelski.

36 MATERIALS SCIENCE↗

System Evaluation and Life-Cycle Cost Analysis of a Commercial-Scale High-Temperature Electrolysis Hydrogen Production Plant

Results of a system evaluation and lifecycle cost analysis are presented for a commercial-scale high-temperature electrolysis (HTE) central hydrogen production plant. The plant design relies on grid electricity to power the electrolysis process and system components, and industrial natural gas to provide process heat. The HYSYS process analysis software was used to evaluate the reference central plant design capable of producing 50,000 kg/day of hydrogen. The HYSYS software performs mass and energy balances across all components to allow optimization of the design using a detailed process flow sheet and realistic operating conditions specified by the analyst. The lifecycle cost analysis was performed using the H2A analysis methodology developed by the Department of Energy (DOE) Hydrogen Program. This methodology utilizes Microsoft Excel spreadsheet analysis tools that require detailed plant performance information (obtained from HYSYS), along with financial and cost information to calculate lifecycle costs. The results of the lifecycle analyses indicate that for a 10% internal rate of return, a large central commercial-scale hydrogen production plant can produce 50,000 kg/day of hydrogen at an average cost of $2.68/kg. When the cost of carbon sequestration is taken into account, the average cost of hydrogen production increases by $0.40/kg to $3.08/kg.

08 HYDROGEN↗

IMPACT OF ALUMINATE IONS ON THE PROPERTIES OF SALTSTONE GROUT MIXES

It is important to identify and control the operational and compositional variables that impact the important processing and performance properties of Saltstone grout mixes. The grout that is produced at the Saltstone Production Facility (SPF) is referred to as Saltstone and is a waste form that immobilizes low concentrations of radionuclides as well as certain toxic metals. The Saltstone will be disposed of in vaults at Savannah River Site (SRS). An effort referred to as the Saltstone Variability Study has been initiated to achieve this goal. The protocols developed in this variability study are also ideally suited as a tool to assess the impact of proposed changes to the processing flow sheet for Liquid Waste Operations at SRS. One such proposal that is currently under consideration is to introduce a leaching step in the treatment of the High Level Waste (HLW) sludge to remove aluminum prior to vitrification at the Defense Waste Processing Facility (DWPF). This leachate would significantly increase the soluble aluminate concentration in the salt feed that will be processed at the SPF. Consequently, an initial study of the impact of increased aluminate concentration on the Saltstone grout properties was performed. Prior work by Lukens (1) showed that aluminate in the salt solutions increases the amount of heat generation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Physical and optoelectronic characterization of reactively sputtered molybdenum-silicon-nitride alloy metal gate electrodes

With continued transistor scaling, work function tuning of metal gates has become important for advanced complementary-metal-oxide-silicon applications. The work function tuning of reactively sputtered Mo{sub x}Si{sub y}N{sub z} (also referred to as MoSiN) gates has been studied through the incorporation of nitrogen. The nitrogen concentration in the MoSiN films was altered by controlling the gas flow ratio, R{sub N}=N{sub 2}/(N{sub 2}+Ar), during gate deposition. The sheet resistance (R{sub s}) of blanket MoSiN films, measured using four-point resistance method, was found to increase as the gas flow ratio was varied from 10% to 40%. Current-voltage measurements confirmed excellent electrical stability of MoSiN/SiO{sub 2}/p-Si gate stack for applied electric fields ranging up to 6 MV/cm. High frequency capacitance-voltage measurements were used to extract the MoSiN work function ({phi}{sub m}) using the relationship between the flatband voltage (V{sub FB}) and the oxide thickness (t{sub ox}). The extracted MoSiN/SiO{sub 2} interfacial barrier heights, obtained through the internal photoemission of electrons, were used to corroborate the extracted values of MoSiN work function. The MoSiN work functions ({phi}{sub m}), extracted independently using both techniques, were consistent and were observed to decrease with increasing gas flow ratio [N{sub 2}/(N{sub 2}+Ar)]. Secondary ion mass spectrometry depth analysis revealed uniform distribution of nitrogen throughout the bulk MoSiN films, with no piling up at gate-dielectric interface. X-ray photoelectron spectroscopy surface analysis suggested a steady increase in the Mo-N bonds, and therefore the total nitrogen concentration (from {approx}20% to 32%), as the gas flow ratio is increased from 10% to 40%. A similar trend was observed in the nitrogen concentration (in percent), measured using Rutherford backscattering spectroscopy, for these gate deposition conditions. These material characterization results demonstrate that the increase in nitrogen concentration in MoSiN films is consistent with the lowering of MoSiN work function. Moreover, the work function of reactively sputtered Mo{sub x}Si{sub y}N{sub z} films was found to be variable over {approx}0.3 eV by adjusting the nitrogen concentration.

36 MATERIALS SCIENCE↗

Dissolution of Material Test Reactor Fuel in an H-Canyon Dissolver

In an amended record of decision for the management of spent nuclear fuel (SNF) at the Savannah River Site, the US Department of Energy has authorized the dissolution and recovery of U from 1000 bundles of Al-clad SNF. The SNF is fuel from domestic and foreign research reactors and is typically referred to as Material Test Reactor (MTR) fuel. Bundles of MTR fuel containing assemblies fabricated from U-Al alloys (or other U compounds) are currently dissolved using a Hg-catalyzed HNO 3 flowsheet. Since the development of the existing flow sheet, improved experimental methods have been developed to more accurately characterize the offgas composition and generation rate during laboratory dissolutions. Recently, these new techniques were successfully used to develop a flowsheet for the dissolution of High Flux Isotope Reactor (HFIR) fuel. Using the data from the HFIR dissolution flowsheet development and necessary laboratory experiments, the Savannah River National Laboratory (SRNL) was requested to define flowsheet conditions for the dissolution of MTR fuels. With improved offgas characterization techniques, SRNL will be able define the number of bundles of fuel which can be charged to an H-Canyon dissolver with much less conservatism.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Baroclinic vortex sheet production by shocks and expansion waves

Vortex sheet production by shocks and expansion waves refracting at a density discontinuity was examined and compared using an analytical solution and numerical simulations. The analytical solution showed that with a small exception, vortex sheet strength is generally stronger in fast/slow shock refractions. In contrast, expansion waves generated a stronger vortex sheet in slow/fast refractions. This difference results in larger vorticity deposited by shocks in fast/slow refractions and by expansion waves in slow/fast refractions. Shock refractions become irregular and the analytical solution fails when either incident, transmitted or reflected shock, exceeded the angle limit for an attached shock. To investigate vortex sheet production outside the range of analytical solutions and to verify the applicability of the planar-interface analytical solution to a curved interface, shock refraction through a sinusoidal interface was numerically simulated in the shock frame of reference. It is found that variation in the local incidence angle along the curved interface creates pressure waves that affect the level of deposited vorticity. This contributes to the difference between predictions from local analysis and numerical computation. Furthermore, an interesting behavior of the shock and expansion wave-deposited vorticity in supersonic ramp flow was discovered. When the high- and low-density streams were swapped, while keeping the incident flow Mach numbers constant, a vortex sheet of equal magnitude but of opposite sign was generated.

97 MATHEMATICS AND COMPUTING↗

Critical layers and protoplanetary disk turbulence

A linear analysis of the zombie vortex instability (ZVI) is performed in a stratified shearing sheet setting for three model barotropic shear flows. The linear analysis is done by utilizing a Green’s function formulation to resolve the critical layers of the associated normal-mode problem. The instability is the result of a resonant interaction between a Rossby wave and a gravity wave that we refer to as Z-modes. The associated critical layer is the location where the Doppler-shifted frequency of a distant Rossby wave equals the local Brunt–Väisälä frequency. The minimum required Rossby number for instability, Ro=0.2, is confirmed for parameter values reported in the literature. It is also found that the shear layer supports the instability in the limit where stratification vanishes. The ZVI is examined in a jet model, finding that the instability can occur for Ro=0.05. Nonlinear vorticity forcing due to unstable Z-modes is shown to result in the creation of a jet flow at the critical layer emerging as the result of the competition between the vertical lifting of perturbation radial vorticity and the radial transport of perturbation vertical vorticity. We find that the picture of this instability leading to a form of nonlinearly driven self-replicating pattern of creation and destruction is warranted: a parent jet spawns a growing child jet at associated critical layers. A mature child jet creates a next generation of child jets at associated critical layers of the former while simultaneously contributing to its own destruction via the Rossby wave instability.

79 ASTRONOMY AND ASTROPHYSICS↗

Southwestern Power Administration Combined Financial Statements, 2006-2009

We have audited the accompanying combined balance sheets of the Southwestern Federal Power System (SWFPS), as of September 30, 2009, 2008, 2007, and 2006, and the related combined statements of revenues and expenses, changes in capitalization, and cash flows for the years then ended. As described in note 1(a), the combined financial statement presentation includes the hydroelectric generation functions of another Federal agency (hereinafter referred to as the generating agency), for which Southwestern Power Administration (Southwestern) markets and transmits power. These combined financial statements are the responsibility of the management of Southwestern and the generating agency. Our responsibility is to express an opinion on these combined financial statements based on our audits. We conducted our audits in accordance with auditing standards generally accepted in the United States of America. Those standards require that we plan and perform the audits to obtain reasonable assurance about whether the combined financial statements are free of material misstatement. An audit includes consideration of internal control over financial reporting as a basis for designing audit procedures that are appropriate in the circumstances, but not for the purpose of expressing an opinion on the effectiveness of Southwestern and the generating agency’s internal control over financial reporting. Accordingly, we express no such opinion. An audit also includes examining, on a test basis, evidence supporting the amounts and disclosures in the combined financial statements, assessing the accounting principles used and significant estimates made by management, as well as evaluating the overall combined financial statement presentation. We believe that our audits provide a reasonable basis for our opinion. In our opinion, the combined financial statements referred to above present fairly, in all material respects, the respective financial position of the Southwestern Federal Power System, as of September 30, 2009, 2008, 2007, and 2006, and the results of its operations and its cash flow for the years then ended, in conformity with U.S. generally accepted accounting principles. Our audits were conducted for the purpose of forming an opinion on the 2009, 2008, 2007, and 2006 SWFPS’s combined financial statements taken as a whole. The supplementary information in the combining financial statements is presented for purposes of additional analysis and is not a required part of the basic combined financial statements. The supplementary information has been subjected to the auditing procedures applied in the audit of the basic combined financial statements and, in our opinion, is fairly stated in all material respects in relation to the basic combined financial statements taken as a whole.

Financial statements, finance, 2009, 2008, 2007, 2↗

High-Performance Graphene Oxide Nanofiltration Membranes for Black Liquor Concentration

Black liquor (BL) concentration by multieffect evaporation is an extremely energy-intensive operation in the kraft pulping cycle. Membranes can significantly save energy in this process, but conventional membranes are strongly challenged by low solute rejections and poor stability in BL, which is a complex mixture containing dissolved lignin, other nonlignin organics, multiple inorganic salts at highly alkaline pH, and process temperatures of 70–85 °C. Here we describe in detail the fabrication, modification, and characterization of robust and high-performance graphene oxide (GO) nanofiltration membranes for BL concentration. We show that poly(ether sulfone) (PES)-supported GO membranes prepared from chemically reduced GO, and then subjected to high-pressure hydraulic compaction, show excellent chemical and mechanical stability under real BL conditions in comparison to conventional GO membranes. These membranes (referred to as “GO-3” in this work) show near-perfect (>99%) lignin rejection, high total organic carbon (TOC) rejection (up to 93%), and greatly improved inorganic rejections especially for divalent anions that are predominant in BL. Finally, the GO-3 membranes are scaled up on larger PES sheets (~660 cm2 in size) and are operated under realistic cross-flow conditions with real BL feed flow rates as high as 10 L/min at 70 °C. The GO-3 membranes show robust performance over more than 1500 h (60 days) of continuous operation in multiple cycles of 10–50 bar transmembrane pressures, attaining stable and sustained permeate fluxes as high as 25 LMH and excellent rejection performance equal to that obtained at smaller scale. The main results of this work have strong implications on the development of membrane processes for BL dewatering and more generally for processing of complex biorefinery feed streams.

Chemistry↗

Dissection of the Voltage Losses of an Acidic Quinone Redox Flow Battery

We measure the polarization characteristics of a quinone-bromide redox flow battery with interdigitated flow fields, using electrochemical impedance spectroscopy and voltammetry of a full cell and of a half cell against a reference electrode. We find linear polarization behavior at 50% state of charge all the way to the short-circuit current density of 2.5 A/cm 2 . We uniquely identify the polarization area-specific resistance (ASR) of each electrode, the membrane ASR to ionic current, and the electronic contact ASR. We use voltage probes to deduce the electronic current density through each sheet of carbon paper in the quinone-bearing electrode. By also interpreting the results using the Newman 1-D porous electrode model, we deduce the volumetric exchange current density of the porous electrode. We uniquely evaluate the power dissipation and identify a correspondence to the contributions to the electrode ASR from the faradaic, electronic, and ionic transport processes. We find that, within the electrode, more power is dissipated in the faradaic process than in the electronic and ionic conduction processes combined, despite the observed linear polarization behavior. We examine the sensitivity of the ASR to the values of the model parameters. The greatest performance improvement is anticipated from increasing the volumetric exchange current density.

25 ENERGY STORAGE↗

VotE-Dams: a compilation of global dams' locations and attributes (v1)

This dataset represents a compilation of two global and three USA-specific datasets of dam locations and their attributes. The major hurdle toward developing this compilation was the identification of duplicates within the source datasets, especially given the variable precision of dam location coordinates. The most immediately-useful product in this dataset is a spreadsheet (VotE-Dams_v1.csv) that documents the unique dams found across the datasets, their coordinates, and their ids within the respective source datasets. We do not reproduce the source datasets (GRaND, GOODD, GeoDAR, NID, and EHA) here, but their download locations are provided in the README files ('Overview' tab). Some of the source datasets are provided as shapefiles, which require geospatial data software to open (e.g. QGIS/ArcGIS for graphical display, geopandas for Python, rgdal for R, many others freely available). The provided README documents metadata of the source datasets and provides attribute-linking information (i.e. matches attributes among various source datasets that contain the same, or similar, information but have different names). Note that the README is provided as both .xslx and a collection of .csvs (one per tab in the .xslx file). We suggest using the .xlsx version that preserves images, formatting, and sheets. .xlsx files can be viewed using (free) Google Docs or Microsoft Excel.Finally, we provide Technical Documentation.pdf that describes the procedures used to identify unique and duplicate dams.The title of this dataset refers to our 'Veins of the Earth' (VotE) project, which seeks to provide a flexible, scale-free representation of the Earth's river networks. Dams are a critical component of VotE as they heavily influence flows throughout river networks.

54 ENVIRONMENTAL SCIENCES↗

initMIP-Antarctica: an ice sheet model initialization experiment of ISMIP6

Ice sheet numerical modeling is an important tool to estimate the dynamic contribution of the Antarctic ice sheet to sea level rise over the coming centuries. The influence of initial conditions on ice sheet model simulations, however, is still unclear. To better understand this influence, an initial state intercomparison exercise (initMIP) has been developed to compare, evaluate, and improve initialization procedures and estimate their impact on century-scale simulations. initMIP is the first set of experiments of the Ice Sheet Model Intercomparison Project for CMIP6 (ISMIP6), which is the primary Coupled Model Intercomparison Project Phase 6 (CMIP6) activity focusing on the Greenland and Antarctic ice sheets. Following initMIP-Greenland, initMIP-Antarctica has been designed to explore uncertainties associated with model initialization and spin-up and to evaluate the impact of changes in external forcings. Starting from the state of the Antarctic ice sheet at the end of the initialization procedure, three forward experiments are each run for 100 years: a control run, a run with a surface mass balance anomaly, and a run with a basal melting anomaly beneath floating ice. This study presents the results of initMIP-Antarctica from 25 simulations performed by 16 international modeling groups. The submitted results use different initial conditions and initialization methods, as well as ice flow model parameters and reference external forcings. We find a good agreement among model responses to the surface mass balance anomaly but large variations in responses to the basal melting anomaly. These variations can be attributed to differences in the extent of ice shelves and their upstream tributaries, the numerical treatment of grounding line, and the initial ocean conditions applied, suggesting that ongoing efforts to better represent ice shelves in continental-scale models should continue.

54 ENVIRONMENTAL SCIENCES↗