Search NASA⌕ Search

SEARCH · Search NASA

Results for “Resistivity measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Local Resistance Measurement for Degradation of c-Si Heterojunction with Intrinsic Thin Layer (HIT) Solar Modules

Silicon heterojunction with intrinsic thin layer (or HIT) modules typically degrade at a rate of less than 1% annually in solar fields with dominant degradation in open-circuit voltage and some degradation in series resistance. However, detailed mechanisms can differ from module to module. Here, we study increases in local series resistance that occur over long-term field deployment, indicated by cell areas where the photoluminescence intensity does not degrade but the electroluminescence degrades significantly. To directly measure the local series resistance, we have cored out the local electroluminescence-degraded area, and we measured the sheet resistance by 4-point-probe and local nm-scale resistance using scanning spreading resistance microscopy (SSRM). The results by 4-point-probe show scattered sheet resistance that can be caused, for example, by nonuniform current paths through the transparent conductive oxide layer, the a-Si:H emitter, or the near-junction c-Si inversion layer. In contrast, the SSRM results indicate a relatively uniform and non-degraded resistivity on smaller nanometer spatial scales. SSRM is an atomic force microscopy-based two-terminal resistance mapping technique that measures the local resistance in nm-volume beneath the probe. The consistent resistances measured on the control and degraded samples can exclude the degradation of transparent conductive oxide resistance.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2023

Electrical, optical, and magnetic properties of amorphous yttrium iron oxide thin films and consequences for non-local resistance measurements

We present magnetic characterization, charge resistivity, and optical photoluminescence measurements on amorphous yttrium iron oxide thin films ( ⁠a-Y–Fe–O), with supporting comparisons to amorphous germanium (⁠ a-Ge) films. We measured magnetic properties with both SQUID magnetometry and polarized neutron reflectometry. These results not only confirm that a-Y–Fe–O is a disordered magnetic material with strong predominantly antiferromagnetic exchange interactions and a high degree of frustration, but also that it is best understood electrically as a disordered semiconductor. As with amorphous germanium, a-Y–Fe–O obeys expectations for variable-range hopping through localized electron states over a wide range of temperature. We also clarify the consequences of charge transport through such a semiconducting medium for non-local voltage measurements intended to probe spin transport in nominally insulating magnetic materials. We further compare non-local resistance measurements made with “quasi-dc” automated current reversal to ac measurements made with a lock-in amplifier. These show that the “quasi-dc” measurement has an effective ac current excitation with frequency up to approximately 22 Hz, and that this effective ac excitation can cause artifacts in these measurements including incorrect sign of the non-local resistance. Here, this comprehensive investigation of non-local resistance measurements in a-Y–Fe–O shows no evidence of spin transport on micrometer length scales, which is contrary to our original work, and in line with more recent investigations by other groups.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Radio frequency electrical resistance measurement under destructive pulsed magnetic fields

We developed a resistance measurement using radio frequency reflection to investigate the electrical transport characteristics under destructive pulsed magnetic fields above 100 T. A sample stage consisting of a homemade flexible printed circuit reduced the noise caused by the induced voltage from the pulsed magnetic fields, improving the accuracy of the measurements of the reflected waves. From the obtained reflectance data, the absolute value of the magnetoresistance was successfully determined by analyzing the phase with admittance charts. In conclusion, these developments enable more accurate and comprehensive measurements of electrical resistance in pulsed magnetic fields.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Two types of superconducting pairs in stripe-ordered La 2 - x Ba x CuO 4 ( x = 1 / 8 ) : Evidence from resistivity measurements

Recent angle-resolved c-axis resistivity measurements of the stripe-ordered La 2-x Ba x CuO 4 (LBCO) with x = 1/8 revealed an unexpected dependence on the direction of the in-plane magnetic field. We argue that these and other available data for the c-axis transport point to the existence of superconducting pairs of two different types in the x = 1/8 LBCO below the stripe ordering temperature. The pairs of one type carry finite momentum and are confined to the Cu-O planes; the pairs of other type (probably the conventional d wave with zero momentum) propagate along narrow conducting channels traversing the sample in the c-axis direction. The evidence for this comes from the observed exponential temperature dependence of the c-axis resistivity ρ c (T ) which we attribute to the thermally excited slips of the superconducting phase and flux flows. We present a simple theory to fit the observed π/2-periodic dependence of ρ c on the direction of the in-plane magnetic field and the other data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

AC resistance measurement of Skew Quadrupole Magnet

This tech note exhibits AC resistance measurement system of the Skew Quadrupole magnet with and without a beam pipe used in the AGS ring. The measurement results are compared with a system that uses skew quad power supply for the magnet. An introduction to ac resistance conceptualization and modeling is presented. It is followed by measurement methodology used and the results.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Evidence of Superconductivity in Electrical Resistance Measurements of Hydrides Under High Pressure

In the standard van der Pauw four-probe configuration commonly used for electrical resistance measurements, including those of hydrogen-rich samples at high pressures, the application of electrical current through one pair of leads while measuring voltage difference across another pair is a fundamental practice (see the inset in Fig. 1c). In the scenario described in Ref. [5], where electrical resistance vanishes due to disconnection between current and voltage probes or due to an onset of giant magnetoresistance in parts of the sample, it is crucial to consider the implications across different probe orientations: while one orientation may indeed result in vanishing electrical resistance, a divergence of the electrical resistance towards infinity will be observed in an alternative orientation where the applied current pattern is rotated a quarter turn (see the scheme on the inset in Fig. 1c). It is imperative to acknowledge that experimental data encompassing all possible probe orientations are essential for eliminating artifacts and assessing sample homogeneity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Screening candidate supplementary cementitious materials under standard and accelerated curing through time-series surface resistivity measurements and change-point detection

Time-series surface resistivity (SR) measurements are evaluated as an indicator of pozzolanicity in concretes containing 13 materials of both known and unknown pozzolanicity, under standard and accelerated curing conditions, and the results were validated against portlandite consumption obtained through thermogravimetric analysis. Change-point detection (CPD) analysis is applied to the data to provide a rigorous indicator of hydration age of the onset and rate of the pozzolanic reaction, if occurring. The SR measurements were able to capture the onset of the pozzolanic reactions in concretes curing at elevated temperature regimes, which allows determination of pozzolanicity weeks earlier than at standard curing temperatures. Using CPD along with slope analysis allows a comprehensive analysis of a material's reactivity and determination of pozzolanicity in as quickly as two days. Time-series SR measurements at elevated curing conditions, along with limits on material composition, are recommended for determination of pozzolanic reactivity in novel or variable materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Intrinsic thermal interfacial resistance measurement in bonded metal–polymer foils

Heat conduction through bonded metal–polymer interfaces often limits the overall heat transfer in electronic packaging, batteries, and heat recovery systems. To design the thermal circuit in such systems, it is essential to measure the thermal interfacial resistance (TIR) across ~1 µm to 100 µm junctions. Previously reported TIR of metal–polymer junctions utilize ASTM E1530-based two-block systems that measure the TIR by applying pressure across the interface through external heating and cooling blocks. Here, we report a novel modification of the ASTM-E1530 technique that employs integrated heaters and sensors to provide an intrinsic TIR measurement of an adhesively bonded metal–polymer junction. We design the measurement technique using finite element simulations to either passively suppress or actively compensate the lateral heat diffusion through the polymer, which can minimize the systematic error to ≲5%. Through proof-of-concept experiments, we report the TIR of metal–polymer interfaces made from DuPont’s Pyralux double-side copper-clad laminates, commonly used in flexible printed circuit boards. Our TIR measurement errors are <10%. We highlight additional sources of errors due to non-idealities in the experiment and discuss possible ways to overcome them. Our measurement technique is also applicable to interfaces that are electrically insulating such as adhesively joined metal–metal junctions and sputter-coated or welded metal–polymer junctions. Altogether, the technique is capable of measuring TIR ≳10 –5 m 2 KW –1 in bonded metal–polymer foils and can be tailored for in situ measurements in flexible electronics, circuit packaging, and other hybrid metal–polymer systems.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Temperature dependent striction effect in a single crystalline Nd 2 Fe 14 B revealed using a novel high temperature resistivity measurement technique

In this work, we studied the temperature dependence of resistivity in a single crystalline Nd 2 Fe 14 B using a newly developed high temperature probe. This novel probe employs mechanical pin connectors instead of conducting glue/paste. From warming and cooling curves, the Curie temperature was consistently measured around T c = 580 K. In addition, anomalous discrete jumps were found only in cooling curves between 400 and 500 K, but not shown in warming curves. More interestingly, when the jumps occurred during cooling, the resistivity was increased. This phenomenon could possibly be due to a temperature dependent striction effect induced by the re-orientation of magnetic domains well below the Curie temperature. Further microscopic study is needed to confirm this effect.

permanent magnet↗
DOE OSTI2023

Estimating Permafrost Distribution Using Co‐Located Temperature and Electrical Resistivity Measurements

Abstract Assessing the lateral and vertical extent of permafrost is critical to understanding the fate of Arctic ecosystems under climate change. Yet, direct measurements of permafrost distribution and temperature are often limited to a small number of borehole locations. Here, we assess the use of co‐located shallow temperature and electrical resistivity tomography (ERT) measurements to estimate at high‐resolution the distribution of permafrost in three watersheds underlain by discontinuous permafrost. Synthetic modeling shows that co‐located temperature and ERT measurements allow for supervised classification schemes that provide 60% higher accuracy compared to unsupervised methods. Linking resistivity and size of the identified permafrost bodies to surface observations, we show that tall vegetation (>0.5 m) and gentle slopes (<15°) are related to warmer and smaller permafrost bodies, and a more frequent occurrence of taliks.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Co-located temperature and electrical resistivity measurements for permafrost mapping, Teller 27, Teller 47 and Kougarok 64, Seward Peninsula, Alaska, late summers of 2018, 2019, 2021, and 2022

This data set contains co-located shallow soil (0.8m below ground level) and electrical resistivity at various depth extracted from Electrical Resistivity Tomography (ERT) measurements. Data were acquired at three watersheds on the southern Seward Peninsula during the late summers of 2018, 2019, 2021, and 2022. The three watersheds are located along the Nome-Teller Highway at mile markers 27 and 47, and along Kougarok Road mile marker 64. The co-located temperature and electrical resistivity data were used to (1) map the spatial extend of near surface permafrost, and (2) for supervised classification of permafrost bodies. This dataset contains .csv, .txt, .srv files and flmd reporting format with data dictionary. Find information about the .srv files at "https://e4d-userguide.pnnl.gov/e4d_guide/elec/e4d_e4d-survey.html". The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Tape-in-tape-out (TITO): a new approach for in-situ contact resistance measurements in high temperature superconducting CORC® cables

One of the ongoing development challenges with ReBCO high-temperature superconducting (HTS) cables is normal zone initiation and local heating, which is associated with over-critical current flowing through and around local performance reductions in individual tapes. Although inter-tape contact resistances are well-reported for individual tapes and HTS cables, these measurements are a challenge in CORC® cables as current percolates through much of the cable. In this work, developments in tape-in-tape-out (TITO) automated individual tape powering experiments are presented, and a simplified modeling approach for current percolation in CORC® cables is developed. An optimization is formulated to fit the model parameters to a large set of TITO experiments on a single cable, allowing the layer-dependent inter-tape contact resistance to be extracted. Measurements are presented and discussed for a straight CORC® cable and a cable bent to a 152 mm and 76 mm radius. The approach provides both quantitative insight and facilitates better understanding of current sharing phenomena in HTS cables.

Teyber, Reed↗
DOE OSTI2020

Mechanical detwinning device for anisotropic resistivity measurements in samples requiring dismounting for particle irradiation

Uniaxial stress is used to detwin samples of orthorhombic iron based superconductors to study their intrinsic electronic anisotropy. Here we describe the development of a new detwinning setup enabling variable-load stress-detwinning with easy sample mounting/dismounting without the need to re-solder the contacts. It enables the systematic study of the anisotropy evolution as a function of an external parameter when the sample is modified between the measurements. In our case, the external parameter is the dose of 2.5 MeV electron irradiation at low temperature. We illustrate the approach by studying resistivity anisotropy in single crystals of Ba 1-x K x Fe 2 As 2 at x =0.25 where the much discussed unusual re-entrance of tetragonal C 4 phase, C 4 → C 2 → C 4 , is observed on cooling. With the described technique we found a significant anisotropy increase in C 2 phase after electron irradiation with dose of 2.35 C/cm 2 .

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Origin of gaplike behaviors in URu 2 Si 2 : Combined study via quasiparticle scattering spectroscopy and resistivity measurements

In this work, we address two long-standing questions regarding the hidden order in URu 2 Si 2 : Is it associated with the hybridization process, and what are the distinct roles played by the localized and itinerant electrons? Our quasiparticle scattering spectroscopy reveals a hybridization gap ubiquitous in the entire phase space spanned by P and Fe substitutions in URu 2 Si 2 , including the no-order and antiferromagnetic regions, with minimal change upon crossing the phase boundary. This indicates its opening is not associated with the ordering, and thus localized electrons must be the major player. Towards a consistent understanding of all the other gaplike behaviors observed only below transition temperatures, we analyze the electrical resistivity using a model in which gapped bosonic excitations are the dominant scattering source. With their stiffness set to follow an unusual temperature dependence (decreasing with decreasing temperature), this model fits all of our resistivity data well including the jump at the transition. Remarkably, the extracted gap increases slowly with increasing Fe content, similarly to the gap detected by inelastic neutron scattering at $Q_1$ = (1.4, 0, 0), suggesting a common origin. Such a model can also naturally explain the Hall effect temperature dependence without invoking Fermi surface gapping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Temperature-Dependent Sheet and Contact Resistivity Measurements on Ag and Ag-Ni Circuit Pastes

The metal circuits and brazes used in electronic, energy conversion, and/or energy storage devices often have difficulty wetting and adhering to ceramic and/or ceramic-passivated metal substrates. Here, a novel Particle Interlayer Directed Wetting and Spreading (PIDWAS) technique is demonstrated that utilizes screen printing, the low wetting angle of silver on nickel, and the high work of adhesion between nickel and various ceramics to produce well-adhered, self-assembled silver patterns on ceramic and/or stainless-steel substrates not normally wet by silver. The resulting Ag-Ni circuits have higher sapphire adhesion strengths (up to 30 MPa on sapphire), higher densities (>97% on sapphire), and similar high-temperature electronic resistivities to those made using commercially-available Heraeus C8710 or DAD-87 silver circuit pastes. Similarly, Ag-Ni brazes between a variety of ceramic and/or stainless-steel substrates have better microstructural stability with rapid thermal cycling, reduction-oxidation cycling, and dual atmosphere isothermal aging than conventional Ag-CuO brazes. In addition, the residual Ni in these Ag-Ni circuits and brazes can be used to chemically getter surface segregated Al, ensuring low contact resistances on a variety of chromia- and/or alumina-passivated stainless steels. Reference: [1] Hu G, Zhou Q, Bhatlawande A, Park J, Termuhlen R, Ma Y, Bieler TR, Yu HC, Qi Y, Hogan T & Nicholas JD. Patterned Nickel Interlayers for Enhanced Silver Wetting, Spreading and Adhesion on Ceramic Substrates. Scripta Materialia, 2021; 196, 113767. 10.1016/j.scriptamat.2021.113767 [2] Park J, Phongpreecha T, Nicholas JD & Qi Y. Enhanced Liquid Metal Wetting on Oxide Surfaces via Patterned Particles. Acta Materialia, 2020; 199, 551-560. 10.1016/j.actamat.2020.08.037

Bhatlawande, Aishwarya↗
DOE OSTI2022

Separation of Kondo lattice coherence from crystal electric field in CeIn 3 with Nd substitutions

The Ce m M n In 3m+2n (m=1,2;n=0,1) family has been one of the most studied families of heavy fermion compounds. This family has revealed many interesting low-temperature physics phenomena, like quantum critical points, heavy fermion superconductivity, and non-Fermi liquid behavior, when these materials are exposed to pressure, magnetic fields, and/or chemical substitution. In this work, we provide a thorough investigation of the Ce 1-x Nd x In 3 phase diagram through single crystal synthesis, x-ray diffraction, energy-dispersive spectroscopy, magnetic susceptibility, and electrical resistivity measurements. Previous electrical resistivity measurements on CeIn 3 reveal a broad maximum, T max ~50 K, which has been associated with the Kondo lattice coherence crossover and/or the crystal electric field depopulation effect as the 4f electrons condense from the high-energy quartet down to the ground state doublet. Our findings show that in the most disordered substitution region, x=0.4–0.5, these features disjoin to reveal two distinct broad humps in electrical resistivity measurements. Magnetic susceptibility and electrical resistivity data on Ce 1-x Nd x In 3 also reveal the antiferromagnetic ordering competition between CeIn 3 and NdIn 3 , where the T N of CeIn 3 is linearly suppressed to a critical concentration of x Nd ~0.6. This concentration is slightly lower than what was previously reported in nonmagnetically substituted Ce 1-x La x In 3 . Our magnetic susceptibility measurements and subsequent simulations show that in the CeIn 3 antiferromagnetic regime, x Nd ≤0.4, the Nd ions act as free paramagnets. The large magnitude of the associated paramagnetic response then masks the overlapping antiferromagnetic ordering signature of the Ce ions. Overall our study further sheds light on the underlying crystal electric field and Kondo lattice coherence interactions within the Ce m M n In 3m+2n family and could stimulate further studies of these systems via neutron diffraction or under applied pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗