Search NASA⌕ Search

SEARCH · Search NASA

Results for “Risers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effects of Riser Diameter on Solids Holdup and Particle Velocity Profiles in Circulating Fluidized Bed Riser Systems

Tests were performed in a 0.1-m diameter small circulating fluidized bed (SCFB) and 0.3 m diameter cold flow circulating fluidized bed (CFCFB) riser systems located at the National Energy Technology Laboratory (NETL) to study the effects of riser diameter on the riser hydrodynamics. These tests were performed at solids circulation rates of G s = 20 and 75 kg/m 2 s and superficial gas velocities of U g = 5.8 and 6.5 m/s using high-density polyethylene (HDPE) pellets with a density of 0.863 g/cm 3 , particle size range of 600–1400 µm (with a Sauter mean diameter of 871 µm, placing them in the Geldart B classification). Comparisons of riser axial pressure and solids fraction profiles, radial particle velocity profiles, and radial profiles of higher statistical moments and select chaos analysis parameters were considered. The results showed that for a given U g and G s , the smaller diameter riser exhibited characteristics associated with more dilute solids flow than that observed in the larger diameter riser. Additionally, the larger diameter riser exhibited a downward flow of solids near the wall under all test conditions, whereas the smaller diameter riser data exhibited little or no indications of solids downflow near the wall. Overall, these findings suggest that, from an industrial standpoint, a direct scaleup of small-scale tests cannot readily be accomplished as the solids holdup and the solids velocity profiles in small units (those normally tested in the laboratory) are not similar to those of large units and the performance of large units can therefore not be predicted from small-scale tests.

42 ENGINEERING↗
NASA NTRS2011

Orion Parachute Riser Cutter Development

This paper presents the tests and analytical approach used on the development of a steel riser cutter for the CEV Parachute Assembly System (CPAS) used on the Orion crew module. Figure 1 shows the riser cutter and the steel riser bundle which consists of six individual cables. Due to the highly compressed schedule, initial unavailability of the riser material and the Orion Forward Bay mechanical constraints, JSC primarily relied on a combination of internal ballistics analysis and LS-DYNA simulation for this project. Various one dimensional internal ballistics codes that use standard equation of state and conservation of energy have commonly used in the development of CAD devices for initial first order estimates and as an enhancement to the test program. While these codes are very accurate for propellant performance prediction, they usually lack a fully defined kinematic model for dynamic predictions. A simple piston device can easily and accurately be modeled using an equation of motion. However, the accuracy of analytical models is greatly reduced on more complicated devices with complex external loads, nonlinear trajectories or unique unlocking features. A 3D finite element model of CAD device with all critical features included can vastly improve the analytical ballistic predictions when it is used as a supplement to the ballistic code. During this project, LS-DYNA structural 3D model was used to predict the riser resisting load that was needed for the ballistic code. A Lagrangian model with eroding elements shown in Figure 2 was used for the blade, steel riser and the anvil. The riser material failure strain was fine tuned by matching the dent depth on the anvil with the actual test data. LS-DYNA model was also utilized to optimize the blade tip design for the most efficient cut. In parallel, the propellant type and the amount were determined by using CADPROG internal ballistics code. Initial test results showed a good match with LS-DYNA and CADPROG simulations. Final paper will present a detailed roadmap from initial ballistic modeling and LS-DYNA simulation to the performance testing. Blade shape optimization study will also be presented.

Oguz, Sirri↗
NASA NTRS2015

NASA CPAS Drogue Textile Riser Feasibility Study

Steel cable was chosen for the lower end of the drogue and main parachute risers on NASA's Orion Multi Purpose Crew Vehicle Parachute Assembly System (CPAS) to protect the risers from extreme temperatures and abrasion should they contact the crew module during deployment, as was done for Apollo. Due to the weight and deployment complexity inherent in steel, there was significant interest in the possibility of substituting textile for steel for the drogue and main parachute risers. However, textile risers could be damaged when subjected to high temperature and abrasion. Investigations were consequently performed by a subset of the authors to determine whether sacrificial, non-load-bearing textile riser covers could be developed to mitigate the thermal and abrasion concerns. Multiple material combinations were tested, resulting in a cover design capable of protecting the riser against severe riser/crew module contact interactions. A feasibility study was then conducted to evaluate the performance of the textile drogue riser cover in relevant abrasive environments. This paper describes the testing performed and documents the results of this feasibility study.

Hennings, Elsa J.↗
NASA NTRS2019

Orion Capsule Parachute Assembly System (CPAS) Riser Twist Load Amplification

Any cluster of parachute systems is subject to effects on performance due to interactions between the parachutes. One such interaction is the twisting of a riser from one parachute around that of another. Due to friction and relative motion between the risers, it is possible for the tension in the riser near the attach point to be different from the tension in the riser towards the suspension lines or canopy. This could result in system failure due to larger than expected loading. The Orion Capsule Parachute Assembly System (CPAS) designed and executed a test to quantify the amplification of the load in a parachute riser due to twist, rocking rate and angle, cluster size, and canopy load. The design of the testing approach, test matrix, and hardware are discussed along with results and findings.

Parachute↗
DOE OSTI2020

The Development of a Generalized Riser Flow Regime Map Based Upon Higher Moment and Chaotic Statistics Using Electrical Capacitance Volume Tomography (ECVT)

Dynamic analyses have been applied to the temporal signals from an Electro Capacitance Volume Tomography instrument located near mid-height on the riser of an industrial-scale cold-flow circulating fluidized bed to characterize gas-solids flow behavior in the riser. Twelve capacitance electrodes surround the cylindrical riser over a height of 1.3 m. The instrument used a neural network deconvolution algorithm to determine the spatially resolved solids fraction recorded at 52 Hz. Experiments were carried out over a range of gas and solids flows in the transport regime using a Geldart Group B bed material, high density polyethylene with mean particle size of 880 μm. The radial solids distribution was found to vary from one-time step to the next between profiles typical of laminar and turbulent flow. The duration of time spent in each of these flow profiles depended upon the operating regime – dilute, core-annular, or fast fluidized bed. The chaotic structure of the temporal data was characterized using the three conventional approaches: the first 4 moments from the distribution of signal in time, system memory parameters from the autocorrelation function and the Hurst exponent, and analysis of the correlationentropy and correlation dimension of the attractor. These signal analysis techniques were used to clearly distinguish differences between different transport operating regimes. Specifically, it was experimentally observed that a riser transitions from core annular flow profile to dilute and dense regimes via increasing the frequency of short term transients to either dilute or dense flow profiles, respectively. A regime map was generated based upon these dynamics using solids flux and gas velocity axes. Fast fluidized, core annular, and dilute each exhibited different degree of dynamic characteristics typical of fluid dominated or particle compromising behavior. It should be noted that the magnitude for the different statistics was in the same range regardless of the regime, it was the radial profile for the statistic that changed and subsequently identified that there was a change in the regime. Finally, a reduced regime map was developed consisting of plotting the gas velocity normalized by the upper transport velocity versus the solids flux normalized by the saturation carrying capacity. The use of this reduced plot allowed the data from widely different conditions to be plotted and compared on the same<p>graph. Note that in many instances, some of the statistics identified the operating point as being in one regime while others indicated that it was in another indicating a transition region between dilute or core annular regimes and between the core annular and fast fluidization regimes. This now provides a tool that can be used to optimize process performance, identify changes in operating states, or replicate process dynamics during process scaling or changing operating parameters. </p>

Breault, Ronald↗
DOE OSTI2025

Design Approach for Circulating Fluidized Bed Riser Reactors such as NETL ASURE: A Review for Clustering Flow

Circulating fluidized bed riser reactors have been a commercial reality for some 80 to 90 years. Through all this time and hundreds if not thousands of research papers on the topic, no clear understanding exists on what is required to design and build a process reactor. There are numerous reasons for this, but the most significant reason is likely that riser reactors are chaotic in nature and unless this chaotic behavior is accounted for, there will be wide discrepancies in the predicted performance and in attempts to scale these reactors without significant trial and error. This work puts forth a new methodology to design riser reactors based upon the desired operating range using the chaotic microstructure behavior. This is accomplished through the use of a nondimensional regime map that was developed using chaotic parameters of memory and order/disorder along with higher moments of skewness and kurtosis. Validation of the approach is provided with circulating fluidized bed combustors and applied to the design of the NETL ASURE facility.

42 ENGINEERING↗
DOE OSTI2021

A fast multi-fidelity method with uncertainty quantification for complex data correlations: Application to vortex-induced vibrations of marine risers

Here we develop a fast multi-fidelity modeling method for very complex correlations between high- and low-fidelity data by working in modal space to extract the proper correlation function. We apply this method to infer the amplitude of motion of a flexible marine riser in cross-flow, subject to vortex-induced vibrations (VIV). VIV are driven by an absolute instability in the flow, which imposes a frequency (Strouhal) law that requires a matching with the impedance of the structure; this matching is easily achieved because of the rapid parametric variation of the added mass force. As a result, the wavenumber of the riser spatial response is within narrow bands of uncertainty. Hence, an error in wavenumber prediction can cause significant phase-related errors in the shape of the amplitude of response along the riser, rendering correlation between low- and high-fidelity data very complex. Working in modal space as outlined herein, dense data from low-fidelity data, provided by the semi-empirical computer code VIVA, can correlate in modal space with few high-fidelity data, obtained from experiments or fully-resolved CFD simulations, to correct both phase and amplitude and provide predictions that agree very well overall with the correct shape of the amplitude response. We also quantify the uncertainty in the prediction using Bayesian modeling and exploit this uncertainty to formulate an active learning strategy for the best possible location of the sensors providing the high fidelity measurements.

42 ENGINEERING↗
DOE OSTI2022

Scaling CFB risers: Maintaining microstructure dynamics

Over the years there have been numerous approaches to develop a scaleup methodology for circulating fluidized beds. Many of these past approaches have relied on macroscopic definitions of similitude to define dimensionless groups such as Reynolds number, Froude number, density ratios, and dimensional ratios involving different length scales. These approaches have demonstrated various levels of success, but often fail when used outside the bounds of experimental datasets. The issue with these methods is that they rely on macroscopic similitude with the hopes that those conditions would provide microscopic similitude as it does in single phase systems where the Buckingham Pi techniques have given reasonable success. Two of the main reasons for failure are 1) changing fluidization regimes and 2) changing material properties that result in the material falling into a different Geldart group. Both are certain to change the microstructure (local instantaneous volume solids fraction) and changes to the microstructure affect the interphase transport properties of the reactor system, namely the mass transfer and heat transfer. Here, this work presents a new approach towards scaling based upon maintaining similitude at the microscale. It reviews a novel dimensionless flow regime map developed from analysis of the deterministic chaos parameters and higher order moments to ensure microstructure similitude. The work then examines four cases from the literature to assess the scaling approach used: (1) same particle-different scale risers for Geldart Group B particles, (2) Glicksman scaling of atmospheric circulating fluidized bed combustor, (3) same particle-different scale risers for Geldart Group A particles and (4) Glicksman scaling for pressurized gasification. General findings are that none of the scaling approaches produced directly applicable microstructure similar behavior based upon the chaotic and higher moment analysis. The positive take away is that the approach can define scale conditions that will provide similar microstructure that can be us to predict transport behavior.

42 ENGINEERING↗
DOE OSTI2023

Scaling CFB risers: Beyond the data using microstructure similarity

Scaling circulating fluidized bed risers has been a point of contention for nearly a century. There have been numerous attempts to define various methodologies. These have all fallen short of providing a robust approach, primarily due to a lack of maintaining microstructure dynamics – a key factor in maintaining interphase heat and mass transfer. Recent work by the author put forward an approach based upon preserving dynamic similarity at different scales by ensuring that the microstructure remained similar by maintaining statistical and chaotic parameters across the scale. That work relied on a dimensionless regime map in which the x-axis was defined by the ratio of the solids flux to the saturation carrying capacity. This latter property was only good within the range of the data, and it became evident that extrapolation beyond the limits of the data could induce unrealistic conditions. Therefore, literature was reviewed to develop a better correlation for the saturation carrying capacity. In doing so, a critical riser diameter concept was developed and applied to the correlations for both Geldart Group A and B materials. The critical diameter for Geldart Group A and B materials is 0.2 m and 0.3 m, respectively. Here the paper then gives three examples on how to use the scaling approach to maintain dynamic similarity across the scales.

02 PETROLEUM↗
DOE OSTI2025

R&D with NREL's Davison Circulating Riser System

The Davison circulating riser (DCR) is the National Renewable Energy Laboratory's (NREL's) pilot-scale recirculating riser reactor system. Coupled with an upstream fluid-bed pyrolysis system, it permits evaluation of catalytic cracking of biogenic feedstocks, as well as coprocessing of biogenic and fossil feedstocks in a commercially relevant pilot fluid catalytic cracker.

09 BIOMASS FUELS↗
DOE OSTI2023

Friction stir welding of thick 7175 aluminium alloy plates for deepwater riser applications

To substantially reduce the cost of extracting petroleum from ultra-deepwater sources, manufacturing risers from 7175 aluminium (Al) alloys rather than steels is being considered. Friction stir welding (FSW), a solid-phase joining technique, is widely applied to 7XXX Al alloys because its mechanical properties are retained within the nugget zone. And, the primary technical objective of the current study is the development of high-strength, corrosion-resistant weldments that connect 7175 Al riser flanges and pipes. However, as the welding thickness increases, the welding speed can be greatly impeded, which lowers the manufacturing efficiency and weakens the mechanical properties in the heat affected zone (next to the nugget). Therefore, obtaining high-performance thick plate 7175 Al alloy joints via FSW is challenging. To overcome this dilemma, the current work optimises the tool design and welding parameters for achieving high-performance joints between 25.4 mm thick 7175 Al alloy plates in butt joint configuration.

Wang, Tianhao↗
DOE OSTI2024

Fluidization Regime Mapping Analysis for 200 μm Glass Beads in a Circulating Fluidized Bed Riser

Powerpoint slides for an oral presentation at the 2024 Clearwater Clean Energy Conference. It includes a brief discussion of a recently developed non-dimensional map for scaling circulating fluidized bed risers using velocity and solids circulation rate ratios. Data is presented for a set of experiments conducted in NETL’s 12-inch cold flow circulating fluidized bed (CFCFB) riser with 200 micron diameter glass beads, showing a strong dependance between solids volume fraction profiles and the solids circulation rate ratio.

Rowan, Steven↗
NASA NTRS2015

Reconstruction of Twist Torque in Main Parachute Risers

The reconstruction of twist torque in the Main Parachute Risers of the Capsule Parachute Assembly System (CPAS) has been successfully used to validate CPAS Model Memo conservative twist torque equations. Reconstruction of basic, one degree of freedom drop tests was used to create a functional process for the evaluation of more complex, rigid body simulation. The roll, pitch, and yaw of the body, the fly-out angles of the parachutes, and the relative location of the parachutes to the body are inputs to the torque simulation. The data collected by the Inertial Measurement Unit (IMU) was used to calculate the true torque. The simulation then used photogrammetric and IMU data as inputs into the Model Memo equations. The results were then compared to the true torque results to validate the Model Memo equations. The Model Memo parameters were based off of steel risers and the parameters will need to be re-evaluated for different materials. Photogrammetric data was found to be more accurate than the inertial data in accounting for the relative rotation between payload and cluster. The Model Memo equations were generally a good match and when not matching were generally conservative.

Day, Joshua D.↗
DOE OSTI2024

Fluidization Regime Mapping Analysis for 200 μm Glass Beads in a Circulating Fluidized Bed Riser

This paper was an executive summary for an oral presentation to be included in the conference proceedings of the 2024 Clearwater Clean Energy Conference. It includes a brief discussion of a recently developed non-dimensional map for scaling circulating fluidized bed risers using velocity and solids circulation rate ratios. Data is presented for a set of experiments conducted in NETL’s 12-inch cold flow circulating fluidized bed (CFCFB) riser with 200 micron diameter glass beads, showing a strong dependance between solids volume fraction profiles and the solids circulation rate ratio.

Rowan, Steven↗
DOE OSTI2022

Transient simulation of biomass combustion in a circulating fluidized bed riser

Interest in circulating fluidized bed (CFB) boilers as a power generation technology has sky-rocketed in recent years because of several advantages this technology offers over conventional boilers, such as increased gas-solid mixing, which results in higher combustion efficiency and the ability to use lower rank fuels. CFB combustors are operated at lower temperatures than conventional thermal power generation combustors, thus reducing NO x emissions, while SO 2 emissions can be conveniently controlled through the addition of Ca-based sulfur sorbents within the combustor. Herin this paper summarizes the modeling effort on a 50 kW th CFB combustor designed, built, and operated at CanmetENERGY in Ottawa, Canada. The numerical model employs the multiphase particle-in-cell (PIC) approach in the open-source Multiphase Flow with Interphase eXchanges (MFiX) Software Suite. The MFiX-PIC model parameters for the simulation are tuned against cold-flow experiments from CanmetENERGY using olivine sand as the inert bed material. It is shown that for the relatively coarse fluid meshes and large parcel sizes necessitated by the scale of the simulation, filter size dependent corrections to the drag law must be incorporated to ensure accuracy of the simulation results. The validated cold flow model is extended to simulate reacting flow with torrefied hardwood as the feedstock and to validate the combustion reaction scheme. The species concentrations at the riser outlet are compared against CanmetENERGY’s experiments and show satisfactory agreement. The simulations demonstrate the ability of MFiX-PIC to accurately capture both the physics and chemistry of a CFB combustor at bench scales, which can be further extended to pilot- and industrial-scale systems.

09 BIOMASS FUELS↗
DOE OSTI2024

Computational Modeling of CO2 Capture By Novel PIM-RU in a Fluidized Bed Riser

The interest in carbon capture, storage, and utilization (CCUS) has increased significantly in the past few decades as it can help mitigate the threat of global warming caused by substantial increase in CO2 emissions due to anthropogenic activities. Although several CO2 capture technologies have been developed, porous solid sorbents, which adsorb CO2 by physisorption, are considered promising candidates for post-combustion CO2 capture because of the easier recovery of adsorbed CO2 and high material stability. Some prominent types of porous solid sorbents are metal-organic frameworks (MOFs), Zeolite, mesoporous silica, and polymer-based sorbents (e.g., polymers with intrinsic microporosity or PIM). Oak Ridge National Laboratory (ORNL) recently developed a novel PIM-based sorbent, referred to here as PIM-RU. The main objective of this work is to investigate the CO2 capture performance of this sorbent using computational fluid dynamics (CFD). While process configuration and reactor design are open questions, a fluidized bed riser was selected as the contactor type for this study.

Aziz, Hossain↗
NASA NTRS1975

Fracture mechanics correlation of boron/aluminum coupons containing stress risers

The mechanical behavior of boron/aluminum near stress risers has been studied and reported. This effort was directed toward defining the tensile behavior of both unidirectional and (0/ plus or minus 45) boron/aluminum using linear elastic fracture mechanics (LEFM). The material used was 5.6-mil boron in 6061 aluminum, consolidated using conventional diffusion bonding techniques. Mechanical properties are reported for both unidirectional and (0/ plus or minus 45) boron/aluminum, which serve as control data for the fracture mechanics predictions. Three different flawed specimen types were studied. In each case the series of specimens remained geometrically similar to eliminate variations in finite size correction factors. The fracture data from these tests were reduced using two techniques. They both used conventional LEFM methods, but the existence of a characteristic flaw was assumed in one case and not the other. Both the data and the physical behavior of the specimens support the characteristic flaw hypothesis. Cracks were observed growing slowly in the (0/ plus or minus 45) laminates, until a critical crack length was reached at which time catastrophic failure occurred.

Adsit, N. R.↗
NASA NTRS1984

Nonlinear Analysis of a Bolted Marine Riser Connector Using NASTRAN Substructuring

Results of an investigation of the behavior of a bolted, flange type marine riser connector is reported. The method used to account for the nonlinear effect of connector separation due to bolt preload and axial tension load is described. The automated multilevel substructing capability of COSMIC/NASTRAN was employed at considerable savings in computer run time. Simplified formulas for computer resources, i.e., computer run times for modules SDCOMP, FBS, and MPYAD, as well as disk storage space, are presented. Actual run time data on a VAX-11/780 is compared with the formulas presented.

Fox, G. L.↗