Results for “Roll-to-roll casting”

DOE OSTI2020

The Effect of Membrane Casting Irregularities on Initial Fuel Cell Performance

Membrane electrode assemblies (MEA) for polymer electrolyte membrane fuel cells (PEMFC) may possess as-manufactured non-uniformities in any of its constituent components. This article studies casting irregularities located within the PEM to understand their potential impact on MEA initial performance. Membrane material was cast on a lab-scale polymer casting line operating either within or at the boundaries of the process window. The resulting membrane material was either pristine in the former case, or, in the latter case, contained air bubbles, cracks, and other irregularities, ranging in size from about 0.6 to 3 mm. Spatial polarization experiments were conducted using a 121-channel segmented fuel cell system, and thermal imaging was performed subsequently to map hydrogen crossover to spatial performance. While total-cell polarization data was minimally impacted by the irregularities, the spatial diagnostics showed local performance impacts that, in operation over time, could cause degradation in performance or earlier failure of the MEA. Such impacts could lead to these irregularities being classified as defects, i.e., manufacturing variations that should be identified and not included in a fuel cell stack. Classification of irregularities as defects will ultimately assist the industry by contributing to the development of threshold detection limits for in-line quality control diagnostics.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗

DOE OSTI2023

Roll-to-roll solvent-free manufactured electrodes for fast-charging batteries

In response to the growing demand for lithium-ion batteries (LIBs), we demonstrate a solvent-free manufacturing technology that can avoid toxic organic solvents and form unique electrode structures to overcome the bottlenecks in low costs and fast charging. The lower tortuosity achieved by the open pores in the dry-printed (DP) electrode allows for a shorter Li+ diffusion pathway, which leads to better rate performance. The DP pouch cells exhibit higher capacity retention of 78% and 69% at 3C and 4C, respectively, compared with 67% and 52% for the slurry cast (SL) cells at the same rates. Moreover, the coating layer on the surface of active materials prevents the excess side reaction between active materials and electrolytes, which prolongs the cycle life of the DP cells. This manufacturing process is a roll-to-roll system with immense potential to be scaled up, providing a more efficient and economical way for battery manufacturing.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Highly permeable polyethersulfone substrates with bicontinuous structure for composite membranes in CO 2 /N 2 separation

Substrate morphology has a significant effect on the CO 2 transport performance of a thin-film composite (TFC) membrane. In this study, a new mixed solvent comprising 2-pyrrolidone (2-PD) and 2-methoxyethanol (2-ME) was used to prepare polyethersulfone (PES) substrates with bicontinuous structure by water vapor-induced phase separation, followed by immersion in water as nonsolvent. Here, compared with the commonly used solvent, N-methyl-2-pyrrolidone (NMP), the 2-PD/2-ME mixed solvent is more hydrophilic and can decrease the thermodynamic stability of the casting solution significantly. As a result, the phase separation was induced via the spinodal decomposition mechanism. The open morphology bestowed the optimized substrate with a very high CO 2 permeance of 133,226 ± 3,870 GPU (1 GPU = 10 –6 cm 3 (STP) s –1 cm –2 cmHg –1 = 3.3464 × 10 -9 kg-mol s –1 m –2 Pa –1 ), which was 5 times more permeable than the baseline substrate synthesized with NMP. By using this new substrate, the prepared TFC membrane containing amines showed an increased CO 2 permeance of 908 ± 8 GPU at 57°C, which was 48 GPU higher than that with the baseline substrate. Meanwhile, the CO 2 /N 2 selectivity was retained at 162 ± 4 at 57°C. In addition, the good scalability of the new PES substrate was demonstrated by roll-to-roll fabrication of a 50' long scale-up PES substrate with a width of 21".

2-Pyrrolidone↗

DOE OSTI2022

Bicontinuous substrates with reduced pore restriction for CO 2 -selective composite membranes

A substrate with bicontinuous structure is attractive for thin-film composite (TFC) membrane synthesis due to its high surface porosity and well-interconnected bulk morphology. In this study, the vapor-induced phase separation (VIPS) of the casting solution comprising water, 2-pyrrolidone, and polyethersulfone (PES) was studied. By tuning the water addition in the casting solution and water vapor exposure time, the optimized substrate exhibited a bicontinuous surface with a high porosity of 24.2% (or 216/µm 2 pore density), thereby mitigating pore restriction and showing a high CO 2 permeance of 2.94×10 5 GPU. Compared to the benchmark PES substrate with cellular surface pores and lower gas permeance, the use of the bicontinuous substrate led to a 12% increase in the CO 2 permeance of the TFC membrane. The mitigated pore restriction was further rationalized by a resistance-in-series model. The analysis of the lateral diffusion and substrate resistances indicates that an even higher surface pore density of the substrate is required to fully realize the potential of ultra-permeable, CO 2 -selective polymers in the TFC configuration. As a result, the scalability of the VIPS process was demonstrated by the roll-to-roll fabrication of the optimized bicontinuous substrate with a width of 21" and a length of >100'.

42 ENGINEERING↗

DOE OSTI2021

Ultra-Fast Vertical Ordering of Lamellar Block Copolymer Films on Unmodified Substrates

To utilize the full potential of block copolymer (BCP) thin films for use in technological devices ranging from ion conduction membranes, transistors to nanowire array antennas, rapid self- assembly of lamellar block copolymers (l-BCPs) with vertically oriented lamellar domains on a variety of unmodified substrates is needed. l-BCPs have an inherently larger interfacial area for transport compared to their cylindrical counterpart. Our observations demonstrate that the as-cast weakly ordered vertically oriented state of l-BCP films of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) from directional evaporation of select solvents, act as “seed templates” for their ultra-fast evolution (~30 s) into well-ordered vertically oriented nanostructures, using a thermal gradient-based Cold Zone Annealing (CZA) technique. Furthermore, vertical lamellae are obtained on unmodified substrates, Quartz and Kapton, and the kinetics of l-BCP ordering is much faster by CZA as compared to the isotropic oven annealing. The rapid ordering kinetics of vertical l-BCPs is tested and found applicable to different molecular weights and film thicknesses ranging from 20 nm to 480 nm, which ultimately flip over to their equilibrium parallel morphology at upper limits of annealing times. This rapid ordering strategy for vertical orientation of l-BCPs using roll-to-roll compatible CZA would be highly relevant for fundamental studies of interfacial transport as well as for industrial applications from membranes to nanowires.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Comparison of the Mechanical Properties of a Conjugated Polymer Deposited Using Spin Coating, Interfacial Spreading, Solution Shearing, and Spray Coating

The mechanical properties of π-conjugated (semiconducting) polymers are a key determinant of the stability and manufacturability of devices envisioned for applications in energy and healthcare. These properties—including modulus, extensibility, toughness, and strength—are influenced by the morphology of the solid film, which depends on the method of processing. To date, the majority of work done on the mechanical properties of semiconducting polymers has been performed on films deposited by spin coating, a process not amenable to the manufacturing of large-area films. Here, we compare the mechanical properties of thin films of regioregular poly(3-heptylthiophene) (P3HpT) produced by three scalable deposition processes—interfacial spreading, solution shearing, and spray coating—and spin coating (as a reference). Our results lead to four principal conclusions. (1) Spray-coated films have poor mechanical robustness due to defects and inhomogeneous thickness. (2) Sheared films show the highest modulus, strength, and toughness, likely resulting from a decrease in free volume. (3) Interfacially spread films show a lower modulus but greater fracture strain than spin-coated films. (4) The trends observed in the tensile behavior of films cast using different deposition processes held true for both P3HpT and poly(3-butylthiophene) (P3BT), an analogue with a higher glass transition temperature. Grazing incidence X-ray diffraction and ultraviolet–visible spectroscopy reveal many notable differences in the solid structures of P3HpT films generated by all four processes. Herein, while these morphological differences provide possible explanations for differences in the electronic properties (hole mobility), we find that the mechanical properties of the film are dominated by the free volume and surface topography. In field-effect transistors, spread films had mobilities more than 1 magnitude greater than any other films, likely due to a relatively high proportion of edge-on texturing and long coherence length in the crystalline domains. Overall, spread films offer the best combination of deformability and charge-transport properties.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Inline Rolling Shear Alignment: Deposition and Long-Range Order of Block Polymer Templates in a Fast, Single-Step Process

We report the first demonstration of a rapid, single-step technique to align block polymer, thin-film nanostructures that is amenable to continuous speeds ≥10 mm/s. This method, termed Inline Rolling Shear Alignment (IRSA), uses an elastomeric roller coupled with an electric hysteresis brake to shear films before the casting solvent fully evaporates, and it can enable high throughput, large-area manufacturing of patterns such as nanowire templates. IRSA is adaptable to various polymer systems including diblock and triblock polymers, and a post-shear annealing step can yield high-quality nanostructures with orientation parameters >0.99 and defect densities as low as 5 defect-pairs/μm 2 . To demonstrate the effectiveness of IRSA, platinum nanowires were produced from this rapid deposition and alignment approach using poly(styrene-b-2-vinylpyridine), followed by open-air, atmospheric-pressure plasma etching. Furthermore, this integrated concept, with 50x faster operation than existing processes, could be leveraged for cost-effective manufacturing of macroscopically aligned nanostructures in roll-to-roll systems.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2019 Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations, though the ink processing, coating and drying processes, to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.

42 ENGINEERING↗

DOE OSTI2021

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2020 Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product. To solve the problems associated with these challenges, the R2R Collaboration is executing a research program with outcomes that will ultimately link modeling, processing, metrology and defect detection tools, thereby directly relating the properties of constituent particles and processing conditions to the performance of final devices. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy materials development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this project leverages the capabilities and expertise at each of five National Laboratories to further the development of multilayer technologies that will enable high-volume, cost-competitive platforms. A typical R2R process has three steps: (1) mixing of particles and various constituents in a slurry, (2) coating of the ink/slurry mixture on a substrate, and (3) drying/curing and processing of the coating. Final performance of devices made via R2R processes is dependent on the active materials (e.g., electrochemical particles in battery or fuel cell electrodes) and the device structure that stems from the governing component interactions within the various steps. However, a fundamental understanding of the underlying mechanisms and phenomena is still lacking, which is why industrial-scale R2R process development and manufacturing is still largely empirical in nature. The FY 2019 through FY 2021 program addresses aspects of the following two targets from the AMO Multi-Year Program Plan: (1) Target 8.1 Develop technologies to reduce the cost per manufactured throughput of continuous R2R manufacturing processes. (A) Increasing throughput of R2R processes by 5 times for batteries (to 50 square feet per minute (50 ft 2 /min)) and capacitors and 10 times for printed electronics and the manufacture of other substrates and MEs used in support of these products. (B) Developing resolution capabilities to enable registration and alignment that will detect, align, and co-deposit multiple layers of coatings and print < 1-micron (1 µm) features using continuous process scalable for commercial production. (C) Developing scalable and reliable R2R processes for solution deposition of ultra-thin (<10 nm) films for active and passive materials. (D) Develop in-line multilayer coating technology on thin films with yields greater than 95%. (2) Target 8.2 Develop in-line instrumentation tools that will evaluate the quality of single and multilayer materials in-process. (A) Developing in-line QC technologies and methodologies for real-time identification of defects and expected product properties “in-use/application” during continuous processing at all size-scales with a focus on the “micro” and “nano” scale traces, lines, and devices, i.e., <1 μm at 300 ft./min for R2R processing in air and <10 nm at 20 ft./min for vacuum (B) Developing technologies to increase the measurement frequency of surface rheology without significant cost increases with a goal of a 10-nanometer in-line profilometry at a production rate of 100,000 square millimeters per minute (100,000 mm 2 /min).

42 ENGINEERING↗

DOE OSTI2022

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration - Early Stage R&D: Phase 2 and FY21 (Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto substrates or membranes that are on moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final product. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes and electrolytes for energy storage, and barrier and membrane materials for decarbonization and air and water filtration. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and heated drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Enabling Bipolar Membrane Manufacturing Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Enabling Roll-to-Roll Manufacturing of Bipolar Membranes Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Layered Electrode Architectures Enabled by Holey Graphene Hosts

Battery electrodes are typically prepared using a slurry-based method, where high boiling point organic solvents are typically used with a polymer binder to disperse active electrode materials and conductive carbon additives followed by casting into current collector sheets. In this process, the use of organic solvents are environmentally hazardous, energy intensive, and time-consuming, while polymeric binders add weight and can undergo parasitic reactions during battery cycling. Here we discuss the use of a unique conductive carbon nanomaterial, namely holey graphene, as a multifunctional host that can be processed via a facile, solvent-free, binder-free, cold pressing method to prepare electrodes with unique architectures. This approach can accommodate a broad range of battery chemistries, such as lithium oxygen/carbon dioxide (Li-O2/CO2), lithium sulfur/selenium (Li-S/Se), and various lithium ion chemistries. The successful use of dry, cold compression allows the convenient modification of electrode mass loading with unique architectures containing active materials randomly mixed or layered with single or multiple layers of one or more active materials. In the conventional slurry-based electrode fabrication method, it is difficult, if not impossible, to achieve such layered architectures. In particular, the layered electrode architectures from the dry, cold press approach are easy to fabricate without significantly sacrificing device performance, and are amenable to continuous roll-to-roll dry processing. In addition, these architectures offer unprecedented perspectives on the battery material loading vs. utilization efficiency, as well as enabling unique characterization opportunities to advance mechanistic understanding of various battery chemistries. Potential applications of this unique electrode fabrication approach for solid-state batteries will also be discussed.

holey graphene, batteries, electrode architecture,↗

DOE OSTI2025

Fabrication and Scale-Up of Porous Polybenzimidazole (PBI) Supports for Gas Separation Composite Membranes

Industrial gas separation often uses thin film composite (TFC) membranes comprising a porous support overlaid with a single-/multi-layer gas-selective thin film. An optimal porous support should possess high surface porosity to minimize gas transport resistance and nano-sized pores to ease pore penetration occurring during the thin film coating process. Good chemical and thermal stabilities are essential to withstand the aggressive solvents and heat required for the thin film coating and curing. However, few porous membranes satisfy all these requirements. This study presents a scalable membrane formation method of making highly porous polybenzimidazole (PBI) supports via non-solvent induced phase separation. This presentation also details the scale-up fabrication of PBI supports using a custom roll-to-roll membrane casting machine.

gas separation↗