Search NASA⌕ Search

SEARCH · Search NASA

Results for “SCALE/KENO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

Setup and verification of a SCALE/KENO platform for generic FHR benchmark calculations

The work presented in this article is preliminary to downstream analysis of a generic fluoride salt-cooled high-temperature reactor (gFHR) core performed by the University of Tennessee in collaboration with Kairos Power (KP). A Monte Carlo transport model of the publicly available gFHR equilibrium core is developed in SCALE/KENO with multigroup energy treatment. Several output quantities of interest are used to verify the simulations against a benchmark model developed by KP using the continuous energy Monte Carlo code Serpent 2. Good agreement is seen in flux and fission rate profiles with a maximum relative difference of 1.4% and 2.8% respectively. Furthermore, an effective multiplication factor bias of 44 pcm was observed between the two simulations. The fuel temperature reactivity coefficient calculated with SCALE is within uncertainty to the reference model. This verification acts as a publicly reproducible benchmark for the gFHR in SCALE/KENO. A simplified depletion model is also presented where a single fuel pebble is depleted to discharge burnup through the equilibrium core while the equilibrium core is assumed to be invariant. This method produces results that intercept the equilibrium core concentrations in every case, however, an interesting artifact of this particular depletion model is uncovered. The phenomenon is shown to be a fundamental feature of the differential rate equations and inspires questions about how this system behaves when the time evolution of the equilibrium core is considered. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

KENO V.a Primer: Performing Calculations using SCALE’s Criticality Safety Analysis Sequence (CSAS5) with Fulcrum

The SCALE code system developed at Oak Ridge National Laboratory is widely used and accepted around the world for criticality safety analyses. The well-known KENO V.a three-dimensional Monte Carlo criticality computer code is one of the primary criticality safety analysis tools in SCALE. The KENO V.a primer is designed to help a new user understand and use the SCALE/KENO V.a Monte Carlo code for nuclear criticality safety analyses. It assumes that the user has a college education in a technical field. There is no assumption of familiarity with Monte Carlo codes in general or with SCALE/KENO V.a in particular. The primer is designed to teach by example, with each example illustrating two or three features of SCALE/KENO V.a that are useful in criticality analyses. The primer is based on SCALE 6.2 and 6.3, which includes the Fulcrum graphical user interface (GUI). Each example uses Fulcrum to provide the framework for preparing input data and viewing output results. Starting with a Quickstart section, the primer gives an overview of the basic requirements for SCALE/KENO V.a input and allows the user to quickly run a simple criticality problem with SCALE/KENO V.a. The sections that follow Quickstart include a list of basic objectives at the beginning that identifies the goal of the section and the individual SCALE/KENO V.a features that are covered in detail in the sample problems in that section. Upon completion of the primer, a new user should be comfortable using Fulcrum to set up criticality problems in SCALE/KENO V.a. The primer provides a starting point for the criticality safety analyst who uses SCALE/KENO V.a. Complete descriptions are provided in the SCALE/KENO V.a manual. Although the primer is self-contained, it is intended as a companion volume to the SCALE/KENO V.a training and documentation. The SCALE manual and training schedule are available at https://scale.ornl.gov. The primer provides specific examples of using SCALE/KENO V.a for criticality analyses; the SCALE/KENO V.a manual provides information on the use of SCALE/KENO V.a and all its modules. The primer also contains an appendix with sample input files. In addition, this primer, its errata and sample inputs are also available at https://code.ornl.gov/scale/primers/kenova.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

HTTR Fuel Block Simulations with SCALE

The SCALE code system is currently being updated to improve the methods and data to support High Temperature Gas Cooled reactor analysis. This paper presents the results of a High Temperature Engineering Test Reactor (HTTR) fuel block analysis with SCALE6.0, which is included as one of the sources of validation data. Good agreement is reported between continuous energy and multigroup SCALE/KENO models of the HTTR block for eigenvalue and fission density distribution. The agreement of the SCALE/KENO results with the MCNP5 results is also very good. The boundary condition is shown to have a large effect on both the calculated eigenvalue and the fission density distribution within the fuel block. In addition to the reported results, a method is proposed to alleviate the fuel mass non-conservation due to the clipping of the lattice of grains within the fuel element in the Monte Carlo continuous energy models. One of the high-temperature gas-cooled (HTGR) reactor technology options under consideration by the Next Generation Nuclear Plant (NGNP) project is based on the prismatic, graphite-moderated reactor design. Within this context, the capability to generate accurate three-dimensional (3-D) core power distributions is one of the main challenges for the NGNP methods development.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

IAEA Coordinated Research Project on HTGR Physics, Thermal Hydraulics, and Depletion Uncertainty Analysis: PHISICS/RELAP5-3D Results for the Phase III Coupled Core Exercises

This report details the Parallel and Highly Innovative Simulation for INL Code System (PHISICS)/Reactor Excursions and Leak Analysis Program (RELAP5)-3D results obtained for the neutronics stand-alone core exercises defined for Phase II of the International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on high-temperature gas cooled reactor (HTGR) uncertainty analysis in modeling (UAM). The Phase II models and results are linked to the earlier Standardized Computer Analyses for Licensing Evaluation (SCALE)/Sampler/New ESC-based Weighting Transport (NEWT) data generated for the lattice physics (lattice) stage Phase I of the CRP. The focus of this report is the propagation of cross-section uncertainties from the lattice to the core calculation (core) phase of the prismatic 350 megawatt (MW) General Atomics (GA) Modular HTGR (MHTGR). The Phase II neutronics exercises consist of two sub-cases (II-2a and II-2b) specified for the fresh and mixed core loading of the MHTGR-350 prismatic high-temperature reactor design. Exercises II-2a and II-2b are performed without temperature feedback using isothermal temperature profiles. For the nominal lattice physics (i.e., best-estimate) model, a series of fresh and depleted single block and super cell SCALE/KENO and SCALE/NEWT models were developed at Idaho National Laboratory (INL) to assess the impact of spectral effects on the few-group cross sections. A combination of these lattice cells were used in a super cell calculation to construct 8-group cross-section libraries for use in the INL-developed PHISICS/RELAP5-3D code suite. The block-level homogenized libraries were assigned to the 220 fuel zones utilized in the MHTGR-350 PHISICS core model, according to the fresh and mixed fresh/depleted core loading pattern. In order to evaluate the effect of uncertainty propagation, several sets consisting of 1,000 perturbed NEWT lattice and PHISICS/RELAP5-3D core calculations were performed using the SCALE 6.2 ENDF/B-VII.1 cross-section co-variance data and the stochastic sampling module Sampler in SCALE 6.2.0. The Figures of Merit (FOM) investigated include the mean and standard deviation uncertainty values obtained for the eigenvalues, control rod worth values, block-averaged power profiles, power axial offsets, and isothermal temperature feedback coefficients. A sensitivity study on the main nuclide reaction contributors to the FOM uncertainties has not yet been performed since the SCALE/PHISICS/RAVEN coupling with ENDF/B-VII co-variance data is still being developed. It was found that uncertainties in the cross sections lead to uncertainties in the local power values of up to 1.5%. The variances between the fresh and mixed/depleted core models are not as large as the axial variations between the top and bottom within each core model. The core eigenvalue uncertainty is approximately 0.5%, which is significant in comparison to typical eigenvalue difference targets (less than ~0.1% for LWRs). The power peaking and axial offset uncertainties are smaller (0.10% – 0.15%) and probably below the level of significance in typical core design metrics. The use of an 8-group energy structure slightly under-estimates some of the uncertainties, but in absolute terms, the uncertainty results are reasonably close to the 26-group results. The 26- and 8-group mean and nominal results differ by a larger degree, and if it can be afforded in terms of calculation resources, the 26-group structure should be used for HTGR calculations. The 8-group structure can, however, still be useful for reasonably accurate uncertainty assessments of transient cases where computational time is important. It was furthermore found that the use of a super cell during the cross-section generation process for better representation of the spectral environment at the core periphery did not lead to significant changes in the core eigenvalues, axial offset, and power peaking uncertainties. The impact of the super cell cross sections on the nominal and mean eigenvalues is, however, important enough (0.6% – 1.1% lower) to justify the use of these super cells for HTGR core simulation to represent the softer spectral environment in the core peripheral regions for nominal best-estimate calculations. The use of super cells for HTGR uncertainty studies is, therefore, not strictly necessary, but the improvements in nominal results could justify their use.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Review of Best Practices for Monte Carlo Criticality Calculations

Monte Carlo methods have been used to compute k eff and the fundamental mode eigenfunction of critical systems since the 1950s. While such calculations have become routine using standard codes such as MCNP and SCALE/KENO, there still remain 3 concerns that must be addressed to perform calculations correctly: convergence of k eff and the fission distribution, bias in k eff and tally results, and bias in statistics on tally results. This paper provides a review of the fundamental problems inherent in Monte Carlo criticality calculations. To provide guidance to practitioners, suggested best practices for avoiding these problems are discussed and illustrated by examples.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Mining Integral Actinides Cross Sections from Reactor Data [Slides]

The conclusions of this paper are: (1) mining of actinide cross-sections from reactor data is a viable and inexpensive approach to confirm burn-up codes; (2) extensive data for actinides in Hanford test data (~200 radiochemical analyses); (3) not only cross-section values and reaction rates can be established but also possible benchmark like data can be constructed to test and validate reactor and criticality safety codes such as SCALE/KENO or MCNPX; and (4) analysis along multiple transmutation paths can be evaluated to show consistency.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Lattice physics calculations using the embedded self-shielding method in polaris, Part II: Benchmark assessment

Polaris is a 2D multigroup lattice physics capability in the SCALE code system used for the analysis of light water reactor fuel designs. In this work, verification and validation results of Polaris in SCALE 6.2 are presented. The SCALE/KENO continuous-energy Monte Carlo code is used as a reference to compare the results of more than 2,000 combinations of pressurized water reactor and boiling water reactor lattice designs and state points. Radiochemical assay measurements were also used to assess the accuracy of depletion calculations. Results show that Polaris, with ENDF/B-VII.1 cross section library, produces accurate lattice physics data for core simulators.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

On the Statistical Uncertainty of Monte Carlo-Calculated Scattering Sensitivities

Sensitivity coefficients calculated with Monte Carlo codes are widely used for nuclear data uncertainty quantification in the modeling and simulation of complex 3D reactor systems. This study systematically compares sensitivity coefficients and associated statistical uncertainties for the multiplication factor and fuel temperature reactivity across multiple Monte Carlo codes (SCALE/KENO, SCALE/Shift, MCNP, and Serpent) using simple models representing light-water reactors and advanced reactor concepts. For multiplication factor sensitivities, statistical uncertainties are generally acceptable, although scattering sensitivities show significantly larger statistical uncertainties than, for example, fission and capture reactions. Fuel temperature reactivity sensitivities show significantly larger statistical uncertainties across all reactions. Elastic scattering sensitivities are the most problematic: all Monte Carlo codes fail to resolve energy-dependent coefficients, and they produce dramatically different energy-collapsed values. Critically, the use of these sensitivity coefficients in nuclear data uncertainty propagation leads to reduced statistical uncertainties in individual uncertainty contributions. This can lead to the masking of unusable sensitivity coefficients and producing misleading uncertainty results. The findings of this study show that new or enhanced methods are needed to improve Monte Carlo elastic scattering sensitivity calculations. Additionally, this study shows the relevance of verifying sensitivity coefficients through direct perturbation calculations for individual nuclide reactions, instead of only for total cross sections as commonly done.

Bostelmann, Rike [ORNL] (ORCID:0000000165968088)↗

IAEA CRP on HTGR UAM: Propagation of Phase I cross section uncertainties to Phase II neutronics steady state using SCALE/SAMPLER and PHISICS/RELAP5-3D

The IAEA Coordinated Research Project (CRP) on High Temperature Gas Cooled Reactor (HTGR) Uncertainties in Modeling (UAM) has been actively supported by the HTGR Methods group at Idaho National Laboratory since 2013. The INL team is responsible for the development of the prismatic reactor design exercises, based on the 350 MW General Atomics Modular HTGR (MHTGR). The focus of this paper is the reporting of the INL results obtained for the propagation of the lattice cross section uncertainties to the stand-alone neutronics simulation of the full MHTGR-350 core. For the nominal (i.e. best-estimate) model, a series of fresh and depleted single block and super cell SCALE/KENO and SCALE/NEWT models were developed at INL to assess spectral effects in the MHTGR-350, and a combination of these lattice cells were used to construct 8-group cross section libraries for use in the INL-developed PHISICS/RELAP5-3D code suite. The block-level homogenized libraries were assigned to the 220 fuel zones utilized in the MHTGR-350 PHISICS core model, according to the fresh and mixed fresh/depleted core loading pattern. A set of 1,000 perturbed NEWT lattice and PHISICS/RELAP5-3D core calculations were performed using the stochastic sampling module SAMPLER in SCALE 6.2. The paper discusses the mean and standard deviation values obtained for the eigenvalue, power offset and peak axial power density uncertainty results for this sequence of 1,000 lattice-to-core MHTGR-350 simulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SCALE 6.2 REACTOR PHYSICS CODE ACCURACY ASSESMENT FOR LIGHT WATER REACTOR FUEL

Verification and validation results of the SCALE 6.2 lattice physics codes TRITON/NEWT and Polaris are presented. The SCALE/KENO continuous energy Monte-Carlo code is used as a reference to compare results of more than 2,000 combinations of pressurized water reactor and boiling water reactor lattice designs and state points. Radiochemical assay measurements were also used to assess the accuracy of depletion calculations. Results show that Polaris and TRITON/NEWT using ENDF/B_VII.1 produce accurate lattice physics calculations and cross section data for core simulators.

Mertyurek, Ugur↗