Search NASA⌕ Search

SEARCH · Search NASA

Results for “SCAP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Design and simulation of n -type solar cells based on an iodine-doped CdTe absorber using SCAPS-1D

The performance of conventional p-type CdTe solar cells has plateaued in recent years, motivating exploration of n-type absorbers. Here, we evaluate a homojunction solar cell employing iodine-doped CdTe (CdTe:I) as the absorber in a Ti 3 C 2 T x MXene/p-CdTe:As/n-CdTe:I/indium structure through SCAPS-1D simulations and prototype devices. Optimized simulations predict efficiencies above 25% for thin CdTe:I absorbers (~0.7 μm). In contrast, the first prototype achieved only ~1.36% efficiency with V OC = 0.48 V, J SC = 6.45 mA/cm 2 and FF = 43.8%. When the simulation is adjusted to match the actual device structure, and the effective illumination is reduced to account for front-side light loss, the predicted V OC (0.48 V) and JSC (6.74 mA/cm 2 ) closely reproduce the experimental values. This suggests that the device performance is primarily limited by reduced front-side photon transmission and other material non-idealities. These results highlight the promise of iodine-doped n-type CdTe and identify clear pathways for further efficiency improvement.

14 SOLAR ENERGY↗
DOE OSTI2025

The influence of ambient light spectrum (LED, INC, CFL, Xenon…) on the efficiency of perovskite indoor photovoltaic solar cells for Internet of Things (IoT) applications

This record provides a numerical investigation of a MAGeI₃-based perovskite solar cell with the structure FTO/TiO₂/MAGeI₃/Spiro-OMeTAD, evaluated for both outdoor and indoor light-harvesting applications using the SCAPS-1D simulator. Device performance is analyzed under AM 1.5G sunlight and several artificial light sources, including LED, incandescent, compact fluorescent lamp (CFL), flashlight, and xenon illumination. The study reports initial and optimized power conversion efficiencies and examines the influence of absorber layer thickness and bandgap on device performance under different lighting conditions. The results highlight the potential of MAGeI₃-based perovskite solar cells for indoor energy harvesting and low-power Internet of Things (IoT) applications.

14 SOLAR ENERGY↗
DOE OSTI2023

Degradation behavior of CIGS solar Cells: A parametric analysis

A parametric study of the effect of bulk and interface properties on device characteristics as a function of heat and light stress under open-circuit and short-circuit conditions is developed for Cu(In,Ga)(S,Se) 2 solar cells using SCAPS-1D simulator. The variables and interdependencies modeled include: (1) conduction band offset (CBO) between buffer and absorber; (2) buffer ionized donor density; (3) CIGS shallow acceptor density; (4) CIGS deep acceptor density; (5) CIGS shallow donor density; (6) ionized acceptor concentration in the ordered vacancy compound (OVC) CIGS/buffer interface; and (7) back contact work-function. An increase in absorber shallow acceptor or a decrease in shallow donor density results in an increase in net carrier density and open-circuit voltage (V OC ). Further, a decrease in V OC is observed with an increase in the deep acceptors or neutral midgap defects in the CIGS due to higher charge carrier recombination. A change of CBO from spike to cliff condition is a dominant mechanism of decreasing VOC with an interface defect density of 10 12 cm -2 . The minimum depletion width is found to be specifically sensitive to CBO and interface defect density. An inflection in the capacitance–voltage curves (in reverse bias) is observed with simultaneous increase in bulk deep acceptor density and shallow donor density near the back contact.

14 SOLAR ENERGY↗
DOE OSTI2024

Exploring the Feasibility and Performance of Perovskite/Antimony Selenide Four-Terminal Tandem Solar Cells

The tandem solar cell presents a potential solution to surpass the Shockley–Queisser limit observed in single-junction solar cells. However, creating a tandem device that is both cost-effective and highly efficient poses a significant challenge. In this study, we present proof of concept for a four-terminal (4T) tandem solar cell utilizing a wide bandgap (1.6–1.8 eV) perovskite top cell and a narrow bandgap (1.2 eV) antimony selenide (Sb 2 Se 3 ) bottom cell. Using a one-dimensional (1D) solar cell capacitance simulator (SCAPS), our calculations indicate the feasibility of this architecture, projecting a simulated device performance of 23% for the perovskite/Sb 2 Se 3 4T tandem device. To validate this, we fabricated two wide bandgap semitransparent perovskite cells with bandgaps of 1.6 eV and 1.77 eV, respectively. These were then mechanically stacked with a narrow bandgap antimony selenide (1.2 eV) to create a tandem structure, resulting in experimental efficiencies exceeding 15%. The obtained results demonstrate promising device performance, showcasing the potential of combining perovskite top cells with the emerging, earth-abundant antimony selenide thin film solar technology to enhance overall device efficiency.

14 SOLAR ENERGY↗
DOE OSTI2023

The Nuclear System-of-Systems Capabilities Analytic Process

This dissertation discusses the impetus for, development of, and initial demonstration of NuSCAPTM: the Nuclear System-of-Systems Capabilities Analytic Process TM . NuSCAP is an approach executed via a Python® application that enables capabilities-based vulnerability analyses of military systems of systems (SOS) exposed to prompt nuclear weapon effects. The NuSCAP application calls on industry-standard, fast-running nuclear weapon effects tools and the Monte Carlo N-Particle®1 (MCNP®) code to evaluate the impact of nuclear weapon environments on the military capabilities of a complex and networked SOS.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗