Search NASA⌕ Search

SEARCH · Search NASA

Results for “SE Product”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Constraining the Synthesis of the Lightest 𝑝 Nucleus 74 Se

We provide the first experimental cross section of the 73 As(p, γ) 74 Se reaction to constrain one of the main destruction mechanisms of the p nucleus 74 Se in explosive stellar environments. The measurement was done using a radioactive 73 As beam at incident energies of 3.1 and 3.7 MeV/nucleon. Along with the total cross section measurement, statistical properties of the 74 Se compound nucleus were extracted, constraining the reaction cross section across the entire Gamow window of the γ process. The impact of the experimentally constrained reaction rate on 74 Se production in Type II supernovae is investigated through Monte Carlo one-zone network simulations. The results indicate that the overproduction of 74 Se by Type II supernova models cannot be resolved by nuclear physics and point towards the description of the astrophysical conditions of the γ process.

59 ≤ A ≤ 89↗
DOE OSTI2025

Discovery of new isotopes in the fragmentation of 82 Se and insights into their production

The production cross sections of neutron-rich nuclei for elements just above 60 Ca were measured at the Facility for Rare Isotope Beams (FRIB). Four previously unobserved isotopes ( 63 Sc, 65,66 Ti, and 68 V) were produced, separated, and identified for the first time using the Advanced Rare Isotope Separator (ARIS). One event was found to be consistent with 61 Ca . The new isotopes were created through the interaction of an 82 Se beam with a carbon target at an energy of 228 MeV/𝑢 and a primary beam current of 1.07 p⁢µ⁢A. The event-by-event particle identification of the mass number (𝐴), atomic number (𝑍), and ionic charge state (𝑞) for the reaction products was achieved by combining measurements of energy loss, time of flight, magnetic rigidity, and total kinetic energy. This successful search for new isotopes, conducted at the beginning of FRIB's third year of operation, highlights the facility's discovery potential, which will continue to grow as the beam current increases. The production cross sections were analyzed in the context of the newly developed Δ⁢𝐵⁢𝐸 systematics that provides trends in neutron-rich regions and increased sensitivity to nuclear binding, an important nuclear structure observable. Furthermore, the new systematics addresses gaps in 𝑄 𝑔 -based methods commonly used to interpret the production cross sections of light neutron-rich elements, and provides an efficient empirical approach to describe cross-section trends across isotopic chains. Good agreement with the measured data was obtained when the Δ⁢𝐵⁢𝐸 systematics and abrasion-ablation calculations were performed using the Hartree-Fock-Bogoliubov (HFB-22) mass table.

59 ≤ A ≤ 89↗
DOE OSTI2026

Adaptive Cybersecurity for Distributed Energy Resources (AdCyDER): Online Reinforcement Learning with Stackelberg-Optimized Defenses — Pipeline Architecture, Evaluation Methodology, and Findings from a Synthetic-Data Evaluation

This report documents the design and evaluation of an integrated online-learning pipeline developed within the AdCyDER project for Distributed Energy Resource (DER) cybersecurity. The pipeline couples a Reinforcement Learning (RL) attack classifier — which produces an attack-type probability distribution — with a Stackelberg game-theoretic (GT) defense selector that consumes those distributions alongside SME-encoded priors over (defense, attack) effectiveness pairings and perdefense costs to choose grid-health-preserving defenses. The objective is not attack classification per se but production of distributions that drive effective defense selection through the Stackelberg layer, learned from delayed grid-health feedback rather than labeled attack data. AdCyDER as a whole is broader than the work presented here; this report covers the specific RL/GT loop integration and its evaluation. We present the integrated pipeline (SCADA telemetry with Fronius inverter physics, Suricata IDS, time-windowed aggregation, per-facility LSTM classifier, Stackelberg optimizer, OpenC2 actuators), an experimental campaign of 28 eight-hour iterations across three baseline modes, and a pipeline-ordered diagnostic protocol. The protocol identifies two distinct failure modes within the loop: paired supervised ceilings on the same features establish that the deployed online RL classifier (macro F1 ≈ 0.07) sits at least 4.7× below a same-architecture supervised LSTM (≈ 0.34) and 10–11× below a linear feature-signal ceiling (≈ 0.70–0.79 depending on per-facility isolation), localizing the dominant failure to the training procedure; and the reward signal driving online updates carries weak directional coupling with classifier correctness in the methodology-expected direction (multi-lens convergent: top-decile P(true) records produce more frequent state changes and slightly larger improvements, top-vs-bot Cohen’s 𝑑 ≈ −0.19), but at effect magnitudes too small to drive gradient-based learning at the campaign sample size. The original learning hypothesis is not supported by the data. The primary contributions are the diagnostic methodology — proposed as a transferable falsification protocol for online RL/GT defense pipelines learning from delayed environmental reward — and the open, reproducible experimental infrastructure. We outline reward reformulation as the highest-priority aspirational next step given the underpowered-but-aligned Q6 reading, with hardware-in-the-loop evaluation as the broadest scope-expansion option.

Blakely, Benjamin [Argonne National Laboratory (AN↗
DOE OSTI2024

A multifunctional technology platform for sorbent construction using polyacrylonitrile scaffolds

Polyacrylonitrile (PAN) is a synthetic polymer that shows high potential for use in a wide range of environmental remediation applications. PAN can be implemented in various ways within a batch or continuous process stream for use as a passive scaffold holding active gettering materials in place or where the PAN scaffold (e.g., beads, fiber mats, membranes) is functionalized with active chelating groups (e.g., amine, hydrazide, amidoximes, carboxyl). Application spaces covered in this review include remediation of heavy metals (e.g., Ag, As, Cd, Cr6+, Cu, Pb, Sb, and Se), high-dose fission products (e.g., 90Sr, 137Cs), radioiodine (i.e., 129I), noble gases (i.e., Xe, 85Kr), rare earths (e.g., Ce, Y), and actinides (e.g., Am, Pu, U). Methods for producing PAN composite sorbents are discussed. Options are also discussed for removing the PAN matrix following chemisorption of an active contaminant to minimize waste volumes requiring disposal.

polyacrylonitrile, composite sorbents, sulfides, a↗
DOE OSTI2025

Sulfur-functionalized solid-phase materials for the selective separation of arsenic and selenium

Radioactive arsenic (As) isotopes are of growing interest for applications in nuclear medicine, national security, and environmental research. Recent efforts at the Facility for Rare Isotope Beams (FRIB) have focused on aqueous harvesting of selenium-72,73 ( 72,73 Se) and their daughter isotopes, arsenic-72,73 ( 72,73 As), which are particularly valuable for medical applications and nuclear data studies, respectively. Both conventional isotope production and harvesting methods require chemical separations to purify radioactive As from parent and co-produced Se radioisotopes. While several solid-phase separation methods for As and Se exist, many depend on complex oxidation state control or highly acidic conditions. This study presents results for sulfur-based solid-phase materials selected to enable uptake at lower acidity and eliminate the need for intricate redox chemistry. Specifically, the performance of three covalently bound sulfur-based ligands were evaluated: (1) thiophenol-polystyrene, (2) propanethiol-silica, and (3) thiourea-silica. Uptake characteristics—including distribution coefficients (Dw), kinetics, and column separation behavior—were assessed using 75 Se and 73 As in hydrochloric (HCl) acid and nitric (HNO 3 ) solutions. The resins demonstrated high-yield (>95%) and high-purity As recovery across a range of HCl concentrations. Comparable results in HNO 3 were achieved when combined with anion exchange chromatography. Furthermore, the potential application of these materials for medical isotope generators was also investigated through ligand stability and repeated elution studies. Overall, sulfur leaching from the resins was negligible at the concentrations relevant for these separations but increased with higher acid concentrations.

Arsenic↗
DOE OSTI2024

Life Cycle Greenhouse Gas Emissions of Growing Intermediate Winter Oilseed Feedstocks for Sustainable Aviation Fuel Production

Ensuring an adequate supply of feedstock is a key challenge to achieving a significant production volume of sustainable aviation fuels (SAFs). One promising feedstock for SAFs is intermediate winter oilseeds added to existing crop production as alternatives to the winter fallow period. In this work, three intermediate winter oilseed crops─camelina ( Camelina sativa L. Crantz .), carinata ( Brassica carinata ), and pennycress ( Thlaspi arvense L .)─are evaluated for their life cycle greenhouse gas (GHG) emissions when harvested and processed into hydroprocessed renewable jet (HRJ). We evaluate solvent extraction (SE) and mechanical pressing as alternative oil extraction methods and examine the impacts of various allocation methods used in the oil extraction process. The GHG emissions reduction potential of camelina-, carinata-, and pennycress-derived HRJs are 50.4%, 65.2%, and 65.7%, respectively, compared to petroleum jet fuel, with SE as an oil extraction method and under mass-based allocation. Combined with the estimated production potential of camelina, carinata, and pennycress as intermediate winter oilseed, 2.5 billion gallons of HRJ can be produced annually, and the total GHG savings could amount to 19.3 million tons when these HRJs replace petroleum jet fuels. In addition, we collect literature information to assess the impacts of these intermediate winter oilseeds on indirect land use change emissions and soil organic carbon sequestration potentials.

camelina↗
DOE OSTI2026

Design-informed neutronics assessment of long-lived fission product transmutation in a tokamak fusion reactor blanket

This study presents a neutronics-based assessment of the feasibility and viability of transmuting six major long-lived fission products (LLFPs) from light-water reactors, namely 99 Tc, 129 I, 79 Se, 93 Zr, 126 Sn, and 135 Cs, within the blanket region of a tokamak fusion reactor, using the MIT ARC design as a concrete fusion configuration. Monte Carlo neutronics simulations were performed to evaluate LLFP transmutation and to compare the results with a reference boiling water reactor (BWR). The results indicate that transmutation of all six LLFPs is neutronics-feasible in fusion reactors, with transmutation half-lives significantly shorter than their natural decay half-lives. For elemental targets, transmutation of 135 Cs, 126 Sn, and 93 Zr was found potentially viable, as the net mass transmuted exceeded that achievable in the reference BWR under identical target volume and irradiation time. When isotopically separated targets were considered, transmutation of 126 Sn and 93 Zr appeared potentially viable. A parametric study demonstrated that plasma geometry modifications can enhance local neutron flux, increasing the transmuted 93 Zr mass by approximately 33% and reducing the transmutation half-life from approximately 240 years to 180 years. Repositioning the target and adjusting material layer thickness reduced the transmutation half-life of 93 Zr to 67 years and increased the net mass transmuted by a factor of 50. Furthermore, these results demonstrate that fusion reactors can enable LLFP transmutation beyond the practical limits of thermal fission reactors and highlight the critical role of reactor and blanket design optimization. Engineering and fuel-cycle considerations required for deployment are beyond the scope of this neutronics-focused study.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Structural Studies of Alloyed and Nanoparticle Transition Metal Dichalcogenides by Selenium-77 Solid-State Nuclear Magnetic Resonance Spectroscopy

Layered transition metal dichalcogenides (TMDCs) such as MoS 2 , MoSe 2 , and WSe 2 are under intense investigation because they are atomically thin semiconductors with photophysical properties that can be tuned by changing their composition or morphology. Mechanochemical processing has been proposed as a method to obtain alloyed TMDCs in the series Mo 1–x W x S y Se 2–y (x = 0–1; y = 0–2). However, elucidating the chemical transformations occurring at the atomic scale following mechanochemical processing can be challenging because the products are often amorphous or microcrystalline. To address this challenge, we probe TMDC mixing and alloying by using a combination of powder X-ray diffraction, Raman spectroscopy, diffuse reflectance spectroscopy, 77 Se solid-state nuclear magnetic resonance (SSNMR) spectroscopy, and planewave density functional theory (DFT) calculations. The nature of the milling material and reaction atmosphere are shown to be essential factors in limiting the formation of undesired oxide byproducts. We demonstrate acquisition of 77 Se SSNMR spectra using different combinations of Carr-Purcell Meiboom-Gill acquisition (CPMG) pulse sequences, magic angle spinning (MAS), and MAS dynamic nuclear polarization. Further, the combination of SSNMR with the other characterization methods clearly demonstrates that high energy impact ball milling induces molecular level alloying of Mo, W and chalcogen atoms in the family Mo 1–x W x S y Se 2–y . Gauge including projector augmented wave DFT calculations yield accurate 77 Se chemical shift (CS) tensor components. 77 Se SSNMR spectroscopy was also applied to study the structure of WSe 2 nanocrystals intercalated with ethylenediamine. The intercalated WSe 2 nanocrystals exhibit a more positive isotropic 77 Se CS as compared to bulk WSe 2 , however, the 77 Se CS anisotropy is the same, confirming the WSe 2 layers have a similar structure as in their bulk counterparts.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Non-Neutron Transmutation of Used Nuclear Fuel (Final Report)

The primary goal of this study is to develop a national facility concept for transmuting long-lived fission products (LLFP) to substantially reduce the disposal impact by minimizing the need for a geologic-timescale repository. As a charter for this study, the national transmutation facility was required to reduce the radiotoxicity and decay heat of LLFP isotopes by at least 90% relative to their values at discharge from a commercial LWR, while consuming less than 10% of the reactor's energy. The identified LLFP isotopes are Se-79, Zr-93, Tc-99, I-129, Sn-126, and Cs-135, whose radiotoxicity is about 99% of the total radiotoxicity of all fission products at 1,000 years. Approximately ~72 kg of LLFPs is discharged every year from a 1,000 MWe commercial or advanced nuclear reactor. First, LLFP transmutation options with non-neutron beams (photons and protons) were explored. The study concluded that LLFP transmutation is feasible with high-energy, high-intensity photons or protons, but impractical on an engineering scale due to low transmutation rates and the high energy requirements to produce the desired photon or proton beams. As alternatives, LLFP transmutation options with neutrons from fission, fusion, and spallation reactions were additionally explored. The transmutation options using advanced critical reactors are attractive only for selective LLFP isotopes because the production rates of several LLFP isotopes (Zr-93, Sn-126, and Cs-135) from fission reactions are larger than the transmutation rates. The transmutation options with only spallation neutrons are favorable to transmute all LLFP isotopes, but as a tradeoff, the net transmutation rates are reduced. The national transmutation facility concept was developed following an exploration of transmutation options using various incident particles. The proposed national LLFP transmutation comprises a dedicated molten-salt reactor (MSR), a proton accelerator, and a spallation neutron-based transmuter. The MSR power was set at 300 MWt and 120 MWe, with the thermal power approximately 10% of that of a commercial 1,000 MWe PWR. The electricity generated by the MSR powers the accelerator and transmuter. The accelerator produces 1 GeV, 30 mA protons, which are introduced into the spallation neutron-based transmuter. The spallation neutron-based transmuter consists of a central spallation target and LLFP target pins merged in a heavy water tank. The six LLFP isotopes are separated into two groups. Tc-99, I-129, and Se-79, having larger neutron cross sections, belong to group A, while Zr-93, Sn126, and Cs-135, having smaller neutron cross sections, belong to group B. Then, for effective transmutation, LLFPs in groups A and B are transmuted in the dedicated MSR and in a spallation neutron-based transmuter, respectively. The estimated capital cost of the national transmutation facility is approximately $\$$3.1B, and its annual O&M cost is expected to be ~$\$$182M. Radiotoxicity and decay heat of LLFPs were calculated and compared with those of the original LLFPs. It was assumed that the targets were made with elementwise LLFP rather than isotopic LLFP, owing to the potentially high cost of isotopic separation from used nuclear fuels. The decay heat of LLFPs can be reduced by more than 90% using a single national transmutation facility. However, radiotoxicity decreases by 79–84%, which does not meet the transmutation performance requirement, primarily because Cs-135 is produced rather than depleted. Thus, to meet the design requirement, Cs-135 should be separated from other Cs isotopes and irradiated in a spallation neutron-based transmuter. Then, radiotoxicity decreases by ~92%.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Accumulation of trace elements in soil and fauna within a site historically contaminated with coal combustion residues

Legacy contaminants tied to energy production are a worldwide concern. Coal combustion residues (CCRs) contain high concentrations of potentially toxic trace elements such as arsenic (As), mercury (Hg), and selenium (Se), which can persist for decades after initial contamination. Coal combustion residue disposal methods, including aquatic settling basins and landfills, can facilitate environmental exposure through intentional and accidental releases. Wildlife exposed to CCRs can experience numerous deleterious effects, such as on development, reproduction, and survival. In the current study, we quantified and compared concentrations of As, Hg, Se, and strontium (Sr) within soils and target fauna (three vertebrate and three invertebrate taxa) from a CCR-contaminated site and a reference site within the U.S. Department of Energy’s Savannah River Site, South Carolina, United States. Our objectives were to (1) compare current concentrations of tested elements in soil and resident fauna to levels from our reference site, (2) assess natural attenuation of elements in soils by comparing current concentrations to historic levels, and (3) evaluate the biomagnification potential of the elements measured via body burden and trophic position correlations among fauna. Here, element concentrations were higher in contaminated soils than reference soils; however, concentrations in 2022 were unchanged from concentrations measured in 2003, suggesting no natural attenuation of tested elements. Additionally, target fauna had elevated As, Se, and Sr levels in comparison to reference samples. A positive correlation was observed in southern toads between Sr concentrations and trophic position, as assessed by nitrogen stable isotope ratios, suggesting potential for biomagnification of Sr within our study system. Collectively, our results demonstrate that legacy contaminants are still present and bioaccumulate in a diversity of taxa in a CCR-contaminated site that has not received effluents in more than 50 years, suggesting monitoring programs in CCR-contaminated sites should be maintained long term in the absence of remediation.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2026

Low-Temperature Gold Deposition Improves CdTe Back Contacts

Improved back contacts can benefit CdTe photovoltaics (PV). In this work, Cd(Se,Te) PV absorbers are cooled during Au evaporation to thermally quench a chemical reaction occurring between gold and CdTe and the generation of a reaction product that lowers device efficiency. Reducing substrate temperature enhances PV power conversion efficiency via open-circuit voltage and fill factor increases. X-ray photoelectron spectroscopy (XPS) reveals that lower temperature also reduces chemical perturbations of the CdTe, potentially linking back contact formation to a CdTe degradation product that hinders PV performance. Comparing reaction enthalpy and substrate heating energy shows that back contact formation by sputtering elemental metals onto ZnTe may exhibit a degradation pathway analogous to that of CdTe/Au reported here. Degradation-diminishing contact formation processes are therefore of general interest for optoelectronic devices, and the reduced substrate temperature in this study is one example.

14 SOLAR ENERGY↗
DOE OSTI2024

Genomic analysis and identification of a novel superantigen, SargEY, in Staphylococcus argenteus isolated from atopic dermatitis lesions

During surveillance of Staphylococcus aureus in lesions from patients with atopic dermatitis (AD), we isolated Staphylococcus argenteus, a species registered in 2011 as a new member of the genus Staphylococcus and previously considered a lineage of S. aureus. Genome sequence comparisons between S. argenteus isolates and representative S. aureus clinical isolates from various origins revealed that the S. argenteus genome from AD patients closely resembles that of S. aureus causing skin infections. We previously reported that 17%–22% of S. aureus isolated from skin infections produce staphylococcal enterotoxin Y (SEY), which predominantly induces T-cell proliferation via the T-cell receptor (TCR) Vα pathway. Complete genome sequencing of S. argenteus isolates revealed a gene encoding a protein similar to superantigen SEY, designated as SargEY, on its chromosome. Population structure analysis of S. argenteus revealed that these isolates are ST2250 lineage, which was the only lineage positive for the SEY-like gene among S. argenteus. Recombinant SargEY demonstrated immunological cross-reactivity with anti-SEY serum. SargEY could induce proliferation of human CD4 + and CD8 + T cells, as well as production of TNF-α and IFN-γ. SargEY showed emetic activity in a marmoset monkey model. S arg EY and SET (a phylogenetically close but uncharacterized SE) revealed their dependency on TCR Vα in inducing human T-cell proliferation. Additionally, TCR sequencing revealed other previously undescribed Vα repertoires induced by SEH. S arg EY and SEY may play roles in exacerbating the respective toxin-producing strains in AD.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

A model to assess Zircaloy’s mechanical property changes following a transient beyond critical heat flux

Maintaining the integrity of nuclear fuel rods is essential for ensuring public health and safety in nuclear power generation. During reactor operation, this integrity is confirmed by demonstrating compliance with established regulatory acceptance criteria. For moderate-frequency events, such as limiting transients and anticipated operational occurrences (AOOs), the current fuel integrity criterion is based on preventing boiling transition. This criterion assumes that prevention of boiling transition will prevent excessive cladding heating and, thus, fuel failure during normal operations. While conservative, this approach places significant constraints on core design, fuel cycle economics, and a plant’s ability to perform major power uprates, leading to suboptimal fuel utilization and inefficient carbon-free energy production. A more efficient approach could be achieved by revising the failure criterion to a material-specific limit rather than strictly preventing the boiling transition, since boiling transition per se is not a cause of fuel cladding failure. Here, as a result, a new licensing framework based on material properties, termed time-at-temperature (t@T), is needed. This approach would allow for brief periods of post–critical heat flux operation during an AOO without compromising safety. Implementing the t@T licensing strategy requires a robust technical foundation in material properties, which must be established through comprehensive data collection on both unirradiated and irradiated fuel and cladding materials. This foundation would enable the development of a safety basis that ensures safe operation while providing greater flexibility and efficiency for reactor operation. This paper documents a thorough review of the available data to establish a baseline knowledge that can inform the development of cladding mechanical models, as well as identify experimental data gaps that need to be addressed in future research. Machine learning and data informatics were utilized to extract the importance of parameters on the t@T parameter. Industry tools were used to perform baseline analyses to define the relevant transient conditions for data analysis. The subsequent review successfully identified applicable experimental data, as well as sufficient data to evaluate changes in cladding mechanical properties following an AOO transient. Rather than developing new models, this work coupled existing irradiation annealing and recrystallization models to calculate changes in hardness, yield stress, and ultimate tensile stress following an AOO event. The findings from this review were summarized to highlight the experimental data needs required to fill remaining gaps and support the development of future t@T licensing methodologies.

Cladding performance↗
DOE OSTI2024

Effects of delta ray electrons on measurement uncertainties of harp system

A harp system, which is a multi-wire beam profile monitoring (MWPM) system, is planned upstream of the spallation target to make in situ calibration of beam current density configuration on the target along with beam imaging from luminescent coating on the beam entrance window at the Second Target Station (STS) of the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). This beam interception-based beam diagnostics system on the target will be used to ensure that the maximum beam loads on the target are within the design range during neutron production. Current design of the harp consists of three layers of measurement wires each of which is sandwiched between voltage biasing wire planes. The signal obtained from each measurement wire layer is disturbed by secondary electrons (SE) and delta rays produced by beam-matter interactions in neighboring wires and ionization of residual gases in accelerator vacuum. While the backgrounds from SE can be suppressed by voltage biasing, the delta-ray electrons with kinetic energies above keV ranges overcome the electric potential bias. In this paper, we study the effects of delta-rays on the measurement uncertainties of MWPM using the particle transport simulation code FLUKA. Furthermore, the cases where the harp system is installed in the proximity of a large delta ray sources such as proton beam window or in the core vessel filled with sub-atmospheric gas have been studied.

Lee, Yong Joong↗
DOE OSTI2024

Ligand Noninnocence in β-Diketiminate and β-Diketimine Copper Complexes

Metal–ligand cooperative systems have a long precedent in catalysis, with the classification depending on the site of substrate bond cleavage and formation and on redox state changes. Recently, our group reported the participation of a β-diketiminate ligand in chemical bonding to heterocumulenes such as CO 2 and CS 2 by tricopper complexes, leading to cooperative catalysis. Herein, we report the reactivity of these copper clusters, [Cu 3 EL] – (E = S, Se; L = tris(β-diketiminate) cyclophane ligand), toward other electrophiles, viz. alkyl halides and Brønsted acids. We identified a family of ligand-functionalized complexes, Cu 3 EL (R) (R = primary alkyls), and a series of disubstituted products, Cu 3 EL (R) 2 , through single-crystal X-ray diffraction, mass spectrometry, and infrared and UV–visible spectroscopy. Furthermore, as part of mechanistic studies on these alkylation reactions, we evaluated the acid–base reactivity of these complexes and the influence of the backbone substitution on the reduction potential. Implications of these findings for ligand noninnocence and the relevance of the metal core as a cofactor for the ligand’s reactivity are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Electrochemical cofactor recycling of bacterial microcompartments

Bacterial microcompartments (BMCs) are prokaryotic organelles that consist of a protein shell which sequesters metabolic reactions in its interior. While most of the substrates and products are relatively small and can permeate the shell, many of the encapsulated enzymes require cofactors that must be regenerated inside. We have analyzed the occurrence of an enzyme previously assigned as a cobalamin (vitamin B 12 ) reductase and, curiously, found it in many unrelated BMC types that do not employ B 12 cofactors. We propose Nicotinamide adenine dinucleotide (NAD+) regeneration as the function of this enzyme and name it Metabolosome Nicotinamide Adenine Dinucleotide Hydrogen (NADH) dehydrogenase (MNdh). Its partner shell protein BMC-T SE (tandem domain BMC shell protein of the single layer type for electron transfer) assists in passing the generated electrons to the outside. We support this hypothesis with bioinformatic analysis, functional assays, Electron Paramagnetic Resonance spectroscopy, protein voltammetry, and structural modeling verified with X-ray footprinting. This finding represents a paradigm for the BMC field, identifying a new, widely occurring route for cofactor recycling and a new function for the shell as separating redox environments.

bacterial microcompartment↗
DOE OSTI2024

Comparison of Geochemical Reactivity of Marcellus and Caney Shale Based on Effluent Analysis

ABSTRACT: In this comparative study, we analyzed the changes in elemental concentrations of hydraulic fracturing fluids after interaction with the Marcellus and Caney Shale formations. The focus was on assessing the inherent risks and environmental implications associated with flowback waters, including their impact on soil, ground, and drinking water quality, and human health safety. The chemical compositions of effluents were determined through Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES) and Mass spectrometry (ICP-MS). The Marcellus Shale, showed concentrations of Cd, averaging 0.380 ppm far exceeding safe water thresholds. Significant levels of As, Se, B, and Pb were detected in both shales, raising concerns about soil and water contamination. Analyzing the effluents from representative samples of sections of the Marcellus (S2 and S7) and Caney (R1 and R2) indicates different geochemical responses over 4 weeks of experiments. This comparison underscores the chemical changes and environmental considerations linked to hydraulic fracturing across shale formations, suggesting the value of tailored monitoring and regulatory measures for each type. 1. INTRODUCTION The Caney and Marcellus shales, differing in geology and geochemistry, represent distinct unconventional reservoirs. The Caney shale, is more ductile, with higher produced water volumes, (Smith et al., 2022) contrasts with the brittle Marcellus shale known for lower brine production but significant data availability. This study aims to elucidate the possible environmental health and safety issues that may arise from the hydraulic fracturing processes. The interaction between fracturing fluids and clays presents a significant challenge. The primary base of these fluids is water, which, when introduced to clay, can induce swelling and constrict flow pathways. This phenomenon is attributed to water molecules infiltrating the layers of clay, particularly in 2:1-type clays, leading to an increased distance between layers. To counteract this, clay stabilizers are employed (Awejori et al., 2021). Despite their effectiveness, these stabilizers are considered temporary solutions. Upon completion of the fracturing process, a concomitant amount of contaminated waters (flow back), with varied content is collected at the surface. From these, we can infer the geochemical reactions and the environmental challenges associated with these waters. Flowback waters can be reinjected or used for other purposes such as irrigation. This requires adequate screening and treatment for safe use.

Dje, L. B.↗
DOE OSTI2025

Nonthermal Ionization of Kilonova Ejecta: Observable Impacts

The characteristic rapid rise and decline at optical wavelengths of a kilonova is the product of the low ejecta mass (≲0.05 M ⊙ ) and high ejecta velocity (≳0.1c). We show that, even at very early times (≲2 days), regions of ejecta fall below critical density and temperature thresholds at which nonlocal thermodynamic equilibrium (NLTE) effects become important. Here, we present an approximate method for calculating the ionization state of the ejecta that accounts for the NLTE impact of high-energy electrons produced in the beta decay of freshly synthesized r-process elements. We find that incorporating ionization from high-energy electrons produces an “inverted” and “blended” ionization structure, where the most highly ionized species are located in the fastest moving homologous ejecta, and multiple ionization states coexist. In radiation transport calculations, the higher degree of ionization reduces line blanketing in optical bands, leading to improved agreement with the light-curve properties of AT 2017gfo, such as the duration, decay rates, brightness, and colors. Our quasi-NLTE implementation helps to alleviate tensions in kilonova modeling: for high-velocity (∼0.3 c) ejecta components, our models require less mass for a given peak brightness in optical bands, by as much as a factor of 3; our models can explain the presence of observed features associated to Sr II, W III, Se III, and Te III under conditions where LTE models would predict only neutral species; and we naturally predict the coexistence of species like Sr II and Ce III without the need for fine-tuning of the ejecta properties.

High energy astrophysics↗