Search NASA⌕ Search

SEARCH · Search NASA

Results for “SE fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Non‐Linear Kinetics of The Lithium Metal Anode on Li 6 PS 5 Cl at High Current Density: Dendrite Growth and the Role of Lithium Microstructure on Creep

Abstract Interfacial instability, viz., pore formation in the lithium metal anode (LMA) during discharge leading to high impedance, current focusing induced solid–electrolyte (SE) fracture during charging, and formation/behaviour of the solid–electrolyte interphase (SEI), at the anode, is one of the major hurdles in the development of solid‐state batteries (SSBs). Also, understanding cell polarization behaviour at high current density is critical to achieving the goal of fast‐charging battery and electric vehicle. Herein, via in situ electrochemical scanning electron microscopy (SEM) measurements, performed with freshly deposited lithium microelectrodes on transgranularly fractured fresh Li6PS5Cl (LPSCl), the LiǀLPSCl interface kinetics are investigated beyond the linear regime. Even at relatively small overvoltages of a few mV, the LiǀLPSCl interface shows non‐linear kinetics. The interface kinetics possibly involve multiple rate‐limiting processes, i.e., ion transport across the SEI and SE|SEI interfaces, as well as charge transfer across the LiǀSEI interface. The total polarization resistance R P of the microelectrode interface is determined to be ≈ 0.8 Ω cm 2 . It is further shown that the nanocrystalline lithium microstructure can lead to a stable LiǀSE interface via Coble creep along with uniform stripping. Also, spatially resolved lithium deposition, i.e., at grain surface flaws, grain boundaries, and flaw‐free surfaces, indicates exceptionally high mechanical endurance of flaw‐free surfaces toward cathodic load (>150 mA cm −2 ). This highlights the prominent role of surface defects in dendrite growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mitigating Battery Cell Failure: Role of Ag‐Nanoparticle Fillers in Solid Electrolyte Dendrite Suppression

Abstract The development of solid‐state batteries (SSBs) with lithium Li metal anodes holds significant promise for enhancing the energy density and safety of next‐generation energy storage systems. However, their commercialization is hindered by challenges related to Li dendrite formation, which can lead to short circuits and battery failure. In this study, the role of Ag nanoparticles embedded within solid electrolytes (SE) is investigated in suppressing dendrite propagation. The results demonstrate that Ag nanoparticles effectively mitigate two key failure mechanisms: (1) dendrite growth within porous networks at low current densities and (2) stress intensification‐induced SE fracture at higher current densities (12 mA cm −2 ). Ex situ characterization using focused‐ion beam – scanning electron microscopy (FIB–SEM) and energy dispersive X‐ray spectroscopy (EDS,) reveals that Ag nanoparticles migrate alongside advancing Li dendrites, promoting homogeneous dendrite growth and reducing the likelihood of localized stress concentrations. Additionally, the incorporation of Ag nanoparticles is shown to facilitate a more uniform Li distribution toward the anode side, which can potentially enable the use of higher charging rates in SSBs. This study provides a new perspective on Li dendrite suppression and presents new opportunities for enhancing the performance and safety of SSBs.

Diallo, Mouhamad Said↗

Modeling of internal mechanical failure of all-solid-state batteries during electrochemical cycling, and implications for battery design

This study is the first quantitative analysis of mechanical reliability of all-solid state batteries. Mechanical degradation of the solid electrolyte (SE) is caused by intercalation-induced expansion of the electrode particles, within the constrains of a dense microstructure. A coupled electro-chemo-mechanical model was implemented to quantify the material properties that cause an SE to fracture. The treatment of microstructural details is essential to the understanding of stress-localization phenomena and fracture. A cohesive zone model is employed to simulate the evolution of damage. In the numerical tests, fracture is prevented when electrode-particle's expansion is lower than 7.5% (typical for most Li-intercalating compounds) and the solid-electrolyte's fracture energy higher than G c = 4 J m -2 . Perhaps counter-intuitively, the analyses show that compliant solid electrolytes (with Young's modulus in the order of E SE = 15 GPa) are more prone to micro-cracking. This result, captured by our non-linear kinematics model, contradicts the speculation that sulfide SEs are more suitable for the design of bulk-type batteries than oxide SEs. Mechanical degradation is linked to the battery power-density. Fracture in solid Li-ion conductors represents a barrier for Li transport, and accelerates the decay of rate performance.

25 ENERGY STORAGE↗

Coupling fracture facies with in-situ permeability measurements to generate stochastic simulations of tight carbonate aquifer properties: Example from the Lower Cretaceous aquifer, Northern Provence, SE France

The relationships between fracture facies and permeability distribution have been explored using a well-constrained 3D implicit structural model of hemipelagic low porosity/low permeability carbonate from the Northern Provence region, SE France. Fracture and permeability facies were determined using an extensive dataset of 99 hydrogeological wells. Data processing was undertaken using a step-by-step approach, involving: (i) identification of the fracture facies based on well logs detailing structure and stratigraphy; (ii) determination of permeability facies from the a priori correlation between the dimension of the hydraulic radius of influence (deduced from slug test analyses) and the type of reservoir heterogeneity (fissure, fracture, fault zone, etc.); (iii) three dimensional plot of fracture and permeability facies in the geological model using a variographic analysis of data. Thirty-three sequential indicator simulations (SIS) based on geostatistic analyses were realised on both fracture and permeability facies. Finally, a connectivity algorithm was developed to compute the probability of connection between selected infiltration areas and the major aquifer springs via moderate- to high-permeability geological bodies. Key results are: (i) fault zones have a greater role in controlling permeability facies distribution than on fracture facies repartition; (ii) there is little correlation between permeability and fracture facies distributions; (iii) connectivity results highlight the compartmentalisation of aquifers in the Cadarache area, the extensions of permeable geological bodies being limited by the N130 faults.

58 GEOSCIENCES↗

Imdr Regio: The Geology of A Possible Active Hot Spot on Venus and A Target for Future Exploration By the ESA Envision Mission.

With Venus being the focus of future new missions like ESA’s EnVision, we need to look for target sites for future investigations on Venus. The different instruments will help to study the planet in a unprecedented detail. In particular, the VenSAR instrument will map the 20% of the surface of Venus at a resolution of 5 to 10 meters/pixel, so it gets crucial to select what areas of Venus deserve to be targeted for such a high-resolution mapping. We propose here Imdr Regio as a good candidate location for combined high resolution SAR mapping and for study with the rest of the mission instruments (e.g., Subsurface Radar Sounder). Imdr Regio is a large topographic rise that extends approximately from 35ºS-50ºS and 195ºE-225ºE between the volcanic plains of Helen, Nsomeka and Wawalag Planitiae. Imdr Regio was classified as a volcano-dominated topographic rise with a minimum-maximum diameter of 1200-1400 km and a swell height of 1.6 km. The southeast of Imdr Regio is dominated by Idunn Mons (46.5ºS/214.5ºE). Studies using the 1 µm (derived) surface emissivity from the Venus Express mission of the volcanic flows surrounding Idunn Mons suggest that high emissivity values in the volcano flanks are related to relatively unweathered basaltic rock and therefore indicative of a recent or even ongoing volcanic activity. We have carried out geologic mapping in the area to constrain volcanic and tectonic structures, and the geologic history of the large topographic rise. This geologic mapping reveals that different styles of volcanism are present across Imdr Regio and that this volcanic activity takes place in all the hot spot in close relation with the formation of a rift throughout all time represented by in the area. The first stages on the evolution of this large volcano are characterized by the formation of a radial fracture system and contemporaneous large sheet flows. These large sheet flows are locally difficult to distinguish from regional plains and are also deformed by regional N-trending wrinkle ridges. After this initial phase, multiple overlapping digitate flow units form the flanks and summit of the volcano and are contemporaneous with NW-SE trending fractures and graben of Olapa Chasma, a rift system that cross the topographic rise. To the northwest another large volcano also presents a system of radial fractures but lacks clear large sheet flows. Numerous pit chains are associated to fractures and graben, suggesting that transport of magma under the surface is important. The geologic history based on the mapping suggests that activity in Imdr Regio started with the emplacement of a plume/diapir in the southeast, which resulted in the formation of a radial dyke system and the emplacement of large sheet flows in Idunn Mons. The presence of other large volcanoes to the northwest suggests the presence of another magmatic source (plume or diapir). After this initial stage, volcanism continues in Idunn Mons and activity in the topographic rise is strongly related to the formation of Olapa Chasma. Rift-related volcanic flows postdate these other volcanoes and are contemporaneous with the late activity in Idunn Mons. Monogenetic volcanism is present in the rift and in all the units that are in the area.

I. López↗

Understanding metal propagation in solid electrolytes due to mixed ionic-electronic conduction

Metal penetration into a solid electrolyte (SE) is one of the critical problems impeding the practical application of solid-state batteries. In this study, we investigate the conditions under which electronic conductivity of the SE can lead to metal deposition and fracture within the SE. Three different stages for void filling (metal plating initiation, metal growth, and metal compression) in the SE are identified. We show that a micron-size isolated void in the SE near the anode can be quickly filled in by metal and fractured when the developed pressure in the void grows larger than the maximum pressure the SE material can sustain. We find that the anode voltage and applied current density play a significant role in determining the vulnerability to metal deposition. We discuss several strategies to prevent electronic conductivity-driven metal propagation in electrolytes that are not fully dense, including the densified layers between the anode and SE.

25 ENERGY STORAGE↗

Site-Specific Sodiation Mechanisms of Selenium in Microporous Carbon Host

We combined advanced TEM (HRTEM, HAADF, EELS) with solid-state (SS)MAS NMR and electroanalytical techniques (GITT, etc.) to understand the site-specific sodiation of selenium (Se) encapsulated in a nanoporous carbon host. The architecture employed is representative of a wide number of electrochemically stable and rate-capable Se-based sodium metal battery (SMB) cathodes. SSNMR demonstrates that during the first sodiation, the Se chains are progressively cut to form an amorphous mixture of polyselenides of varying lengths, with no evidence for discrete phase transitions during sodiation. Here, it also shows that Se nearest the carbon pore surface is sodiated first, leading to the formation of a core–shell compositional profile. HRTEM indicates that the vast majority of the pore-confined Se is amorphous, with the only localized presence of nanocrystalline equilibrium Na 2 Se 2 (hcp) and Na 2 Se (fcc). A nanoscale fracture of terminally sodiated Na–Se is observed by HAADF, with SSNMR, indicating a physical separation of some Se from the carbon host after the first cycle. GITT reveals a 3-fold increase in Na + diffusivity at cycle 2, which may be explained by the creation of extra interfaces. These combined findings highlight the complex phenomenology of electrochemical phase transformations in nanoconfined materials, which may profoundly differ from their “free” counterparts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Minimization of Cathode|Solid-Electrolyte Interfacial Delamination through the Application of Interphase Layers

Next-generation lithium-ion batteries are expected to use solid electrolytes (SEs) to enable higher energy density and extreme fast-charge capabilities. One major mode of degradation at the cathode|SE interface is delamination between the cathode active materials and SEs, which leads to performance decay. Experimental observations indicate that implementation of interphase layers can minimize the cathode|SE delamination induced capacity fade. A multiscale computational methodology is developed here to investigate the applicability of boron substituted lithium carbonate (Li 2+x B x C 1–x O 3 , x = 0.5, or LBCO) to minimize the delamination at the cathode|SE interface. Atomistic simulations indicate that the fracture energies at both the cathode|LBCO and LBCO|SE interfaces are higher than those at the cathode|SE interface, which reduces the extent of delamination. Mesoscale simulations indicate that, apart from increasing the fracture energy, decreasing the evolution of strain energy by lowering the elastic modulus of the interphase layer can also minimize the extent of delamination at the cathode|SE interface. However, the adoption of an interphase layer with high ionic conductivity is necessary to minimize the ohmic losses during operation at higher current densities. This study provides guidance on selecting interphase layers with specific properties and thicknesses to minimize both interfacial delamination and impedance growth.

LBCO↗

Development of techniques to simplify the process of investigation and estimate of natural resources in remote and relatively unexplored areas, Venezuela

The author has identified the following significant results. Based upon the results obtained by both interpretations, radar and satellite, highly fractured zones were outlined and checked against geologic rock samples. Most of the rock samples were collected along the Ventuari River that crosses most of the project area from NE to SE. The structural orientation and fracture patterns were taken into consideration during the planning of flight lines, also the magnetic declination of the area. Most of the flight lines were oriented N 30 deg W across known structural trends; the altitude above ground was 450 feet, and the distance between lines was 3000 feet. The ERTS image permits the obtention of a panoramic vision of the area, and facilitates the exact delineation of major drainages. Topographic changes are easily observed. Rocky outcrops are easily distinguishable on band 5 and 7. Shrub vegetation zones are distinguishable on both bands, without possible separation of forest types, this is possible only when the physiographic conditions of small textural differences are taken into account.

Romero, A. C.↗

Clustered BSRs: Evidence for gas hydrate-bearing turbidite complexes in folded regions, example from the Perdido Fold Belt, northern Gulf of Mexico

We detail previously undocumented but extensive gas hydrate accumulations in the mouth of Perdido Canyon in the northern Gulf of Mexico. The accumulations are located within central parts of structural domes (four-way closures) and are characterized by stacked, high-amplitude bottom simulating reflections (BSRs) that we call clustered BSRs. Seismic data from Perdido Canyon show two clustered BSRs associated with turbidite sequences within two dome folds formed from tectonic folding and salt diapir rise. The northwestern (NW) and southeastern (SE) clustered BSRs have aerial extents of ~25 km2 and 50 km2, respectively. Well log data confirm gas hydrate occurs above the NW clustered BSR, within a 225 m-thick consistently high-resistivity interval that we interpret as gas hydrate in near-vertical fractures and turbidite sands. The SE dome is only drilled at the edge of the BSR; nevertheless, the well log data indicate that a 30 m-thick gas hydrate accumulation is present. Gas chromatographic logs in both domes suggest a gradual transition from predominantly microbial gas below the BSR (500–1000 m below seafloor (mbsf)) to thermogenic gas at 1000–2000 mbsf. Based on the well log data and seismic stratigraphic analysis, we find gas hydrate is concentrated in fractures in marine mud, as well as in the pores of submarine fan turbidities, where saturations reach as high as 75%. An estimate of the total gas hydrate-bound gas volume at standard temperature and pressure is between 0.04 and 0.17 trillion cubic meters (TCM) assuming average hydrate saturation of 5-20% in a ~45 m thick turbidite sand unit above the Perdido Canyon BSR area. Measured BSR extent and gas volume estimates indicate that the NW and SE reservoirs are among the largest gas hydrate occurrences known in the Gulf of Mexico.

58 GEOSCIENCES↗

Tuscaloosa Marine Shale: Seal or Source? Petrophysical Comparative Study of Wells in SE Louisiana and SW Mississippi

The Tuscaloosa Marine Shale (TMS) is a versatile Late Cretaceous shale formation present in central and SE Louisiana and SW Mississippi, which drew attention because of the various roles played within the Tuscaloosa Group. In this paper, it is debated whether the Tuscaloosa Marine Shale can act as a source, reservoir, or seal all throughout the shale play or only in certain areas. Well log and core data from Adams County, Mississippi, are compared to data from East Feliciana Parish in Louisiana. Conclusions were drawn based on the results of well log analysis, X-ray Diffraction (XRD), porosity–permeability measurements, programmed pyrolysis, and fracture analysis. It was shown that the Tuscaloosa Marine Shale interval in SE Louisiana consists of important amounts of calcite, exhibits multiple natural fractures, has porosity values as high as 9.3%, and shows a TOC content of up to 2.8 wt%. On the other hand, samples from a well at the Cranfield field, MS, are characterized by considerably lower TOC values of around 0.88 wt%, porosities between 0.33% and 4%, and no serious fracturing. The formation demonstrates better reservoir and source potential in SE Louisiana and reliable CO2 sealing capacity in SW Mississippi. The analysis presented in this paper represents a holistic approach to the characterization of shale formations, is applicable to other plays around the world, and can be used as an integral part of CO2 sequestration or hydraulic fracturing programs.

04 OIL SHALES AND TAR SANDS↗

Direct Observation of Interfacial Mechanical Failure in Thiophosphate Solid Electrolytes with Operando X-Ray Tomography

Herein, the mechanical behaviors of Li 10 GeP 2 S 12 (LGPS) solid electrolytes during electrochemical cycling using operando X-ray tomography are investigated. It is demonstrated that the bulk mechanical decomposition of LGPS when cycled against lithium is a direct result of electrochemical reduction of the solid electrolyte at the LGPS/Li 0 interface. The reductive decomposition of LGPS during lithium plating results in the formation of low-density domains at the electrode/electrolyte interface, which impose sufficient mechanical stress on the underlying LGPS to crack the SE pellet. The critical stress developed prior to pellet fracture is significantly lower than the bulk shear modulus of LGPS, suggesting that the electrochemical instability of LGPS dramatically worsens the mechanical stability of the material near the LGPS/Li 0 interface. It is also shown that the application of a highly concentrated liquid electrolyte to the LGPS surface suppresses the reductive decomposition of LGPS, improving both the electrochemical performance and mechanical stability of the bulk LGPS solid electrolyte.

36 MATERIALS SCIENCE↗

ASTM E399 Standard Development - KIsi Analysis Method

The ASTM E399 test method is used to determine the plane‐strain fracture toughness, K (sub IC), for metallic materials. The test consists of monotonically loading a pre-cracked test specimen to failure while recording the applied load and the crack mouth opening displacement. Several test specimen types are allowable per ASTM E399; two common geometries are the compact tension (C(T)) and the single-edge bend (SE(B)) geometries. The test result is an estimate of the plane‐strain fracture toughness, K (sub q), determined by the intercept of the test record with a 95 percent secant-offset construction line. The 95 percent offset represents crack extension corresponding to approximately 2 percent of the original specimen ligament (assuming that all compliance change is the result of crack extension). If the test meets certain validity requirements based on specimen size and test behavior, the result is valid, and K (sub q) equals K (sub IC).

Tilson, William G.↗

Mechanical Properties of 2D LiInP 2 Se 6 : Implication for Semiconductor Applications

Metal phosphorus trichalcogenides (MPTCs) are emerging 2D semiconductor materials with unique functional properties that set them apart from other 2D systems. Despite the importance of their mechanical properties for improving the semiconductor device’s durability and performance, as well as for utilizing strain effects to customize material properties and create new functionality, our current understanding of MPTCs’ mechanical behavior is lacking and lags behind our knowledge of their other properties. Here, we use LiInP 2 Se 6 as a model example of MPTCs and report the first experimental measurements of the elastic and plastic (fracture) properties along both in-plane and out-of-plane directions by atomic force microscopy and nanoindentation. Being a 2D material that is entirely inorganic, LiInP 2 Se 6 surprisingly exhibits mechanical properties that resemble those of hybrid organic–inorganic materials rather than pure inorganic 2D materials. It has a soft crystal structure with low elastic moduli, a low difference in in-plane vs out-of-plane mechanical properties, and a combination of elastic and plastic characteristics of hybrid organic–inorganic materials. Furthermore, our work provides the mechanical information critically needed to mitigate and/or harness the strain effects in LiInP 2 Se 6 -based semiconductor devices and sheds light on the mechanical behaviors of MPTCs with indispensable insights.

2D semiconductor↗

Geometry and relative age of large patterned fractures in southern Acidalia Planitia, Mars

Extraordinary patterned fractures occur in Elysium, Utopia, and Acidalia Planitiae of Mars. Theories as to their origin range from permafrost patterning to tectonic fracturing. Recent studies indicate the patterned fractures may be a surface reflection of rough, buried terrane in which fracturing occurs as a result of differential compaction. The patterned terrane in the southern portion of the Acidalia region (MC4-SE, MC4-SC) is being studied to determine its age relative to other terranes and events, and to constrain models for the origin of the fractures. Fracturing in this area occurs between 5 and 25 degrees west longitude and 37 and 50 degrees north latitude. Many fracture patterns are roughly polygonal, with polygons ranging in size from approximately 11 to 32 km in diameter. Fracture traces range from the limit of resolution (10's of meters) to 35 km in length.

Borrello, Murray C.↗

Metal plasticity and ductile fracture modeling for cast aluminum alloy parts

Here in this study, plasticity and ductile fracture properties were characterized by performing various tension, shear, and compression tests. A series of 10 experiments were performed using notched round bars, flat-grooved plates, in-plane shear plates, and cylindrical bars. Two cast aluminum alloys used in automotive suspension systems were selected. Plasticity modelling was performed and the results were compared with experimental and corresponding simulation results; further, the relationships among the stress triaxiality, Lode angle parameter, and equivalent plastic strain at the onset of failure were determined to calibrate a ductile fracture model. Finally, the proposed ductile fracture model shows good agreement with experimental results.

36 MATERIALS SCIENCE↗

IAEA Coordinated Research Project on Master Curve Approach to Monitor Fracture Toughness of RPV Steels: Final Results of the Experimental Exercise to Support Constraint Effects

The precracked Charpy single-edge notched bend, SE(B), specimen (PCC) is the most likely specimen type to be used for determination of the reference temperature, T0, with reactor pressure vessel (RPV) surveillance specimens. Unfortunately, for many RPV steels, significant differences have been observed between the T0 temperature for the PCC specimen and that obtained from the 25-mm thick compact specimen [1TC(T)], generally considered the standard reference specimen for T0. This difference in T0 has often been designated a specimen bias effect, and the primary focus for explaining this effect is loss of constraint in the PCC specimen. The International Atomic Energy Agency (IAEA) has developed a coordinated research project (CRP) to evaluate various issues associated with the fracture toughness Master Curve for application to light-water RPVs. Topic Area 1 of the CRP is focused on the issue of test specimen geometry effects, with emphasis on determination of T0 with the PCC specimen and the bias effect. Topic Area 1 has an experimental part and an analytical part. Participating organizations for the experimental part of the CRP performed fracture toughness testing of various steels, including the reference steel JRQ (A533-B-1) often used for IAEA studies, with various types of specimens under various conditions. Additionally, many of the participants took part in a round robin exercise on finite element modeling of the PCVN specimen, discussed in a separate paper. Results from fracture toughness tests are compared with regard to effects of specimen size and type on the reference temperature T0. It is apparent from the results presented that the bias observed between the PCC specimen and larger specimens for Plate JRQ is not nearly as large as that obtained for Plate 13B (-11 C vs -37 C) and for some of the results in the literature (bias values as much as -45 C). This observation is consistent with observations in the literature that show significant variations in the bias that are dependent on the specific materials being tested. There are various methods for constraint adjustments and two methods were used that reduced the bias for Plate 13B from -37 C to -13 C in one case and to -11 C in the second case. Unfortunately, there is not a consensus methodology available that accounts for the differences observed with different materials. Increasing the Mlim value in the ASTM E-1921 to ensure no loss of constraint for the PCC specimen is not a practicable solution because the PCC specimen is derived from CVN specimens in RPV surveillance capsules and larger specimens are normally not available. Resolution of these differences are needed for application of the master curve procedure to operating RPVs, but the research needed for such resolution is beyond the scope of this CRP.

36 MATERIALS SCIENCE↗