SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report continues the work presented in NACA-TM 605 and expands the scope to include the change in specific number of wrinkles from direction x to z, so that b and f become variable in direction z. Moreover, it seems likely that b and f increase from the edge toward the center if the sheet is infinitely thin.
Noting that the stiffness of the girder increases very rapidly as Beta increases, the result can be summed up as follows: When the cross stress preponderates in one direction and when the web plate is to be given the dimensions commensurate to its stresses, it is advisable (regardless of any ensuing structural difficulties) to set the uprights at about Beta = 120 degrees, thereby lowering the weight of the plate wall 15 percent (in contrast to Beta = 90 degrees), and raising the stiffness 55 percent. But, when the cross stresses alternate and are approximately of the same intensity in both directions, or, if the web plate thickness is determined by other structural reasons, then Beta = 90 degrees should be chosen.
Tearing of aluminum sheet metal durinng stretch forming prevented by flame spraying layer of aluminum on edges held in stretch-forming machine. Technique improves grip of machine on metal and reinforced sheet better able to with stand concentration of force in vicinity of grips.
As the in-space economy matures, the migration of typically Earth-bound manufacturing methods, such as metal forming and joining, up to space will be required to meet the increasing demand for refueling and supply depots, habitats, laboratories, lunar surface structures, and sites for deep-space exploration shipbuilding. Only in this way can the magnitude of individual structures begin to exceed what can be launched, deployed, docked, or inflated and allow true economies of scale to be unlocked in space. However, typical terrestrial methods of forming and shaping sheet metal require massive machinery with the ability to deflect reaction forces to a large mass in a fixed reference frame (Earth). To both limit up-mass required for manufacture and to mitigate the issues of reaction forces in the relative reference frames of space, a non-contact, laser-based method of forming metal sheet is proposed. NASA Marshall Space Flight Center (MSFC), in cooperation with DARPA and the University of Florida (UF), have begun investigation of non-contact methods of laser forming sheet metal in thermal vacuum (TVAC) conditions to great success. To date, several grades of aluminum, stainless steel, and titanium coupons have been formed via laser-induced internal stresses in these metals at both ambient atmosphere and vacuum conditions. Temperatures in these tests ranged from -120 to 60 C, and though the total energy required to induce strain does vary with workpiece temperature and environmental pressure, the method remains predictable and controllable for the materials investigated. It is believed that this method will revolutionize manufacturing in-space as it not only continues to build upon the capabilities of the laser (sensing, marking, cutting, drilling, joining, and now forming) as an all-in-one tool, but also reduces the need to counteract forming forces as would be required in mechanical bending. In theory, all required stress to induce bending is generated through thermal gradient and strain within the workpiece, meaning that the need for reaction control and fuel expense on-orbit will be limited. Archimedes once stated, “Give me a lever long enough and a fulcrum on which to place it, and I shall move the world”. With a laser as our lever and our workpiece its own fulcrum, we can move the world’s manufacturing into space.
Sheets only few mils thick bonded together, punched, then debonded. Three-step process yields perforated sheets of metal. (1): Individual sheets bonded together to form laminate. (2): laminate perforated in desired geometric pattern. (3): After baking, laminate separates into individual sheets. Developed for fabricating conductive layer on blankets that collect and remove ions; however, perforated foils have other applications - as conductive surfaces on insulating materials; stiffeners and conductors in plastic laminates; reflectors in antenna dishes; supports for thermal blankets; lightweight grille cover materials; and material for mockup of components.
Tool attachment reduces heat distortion of sheet. Air-guide attachment directs air from grinder motor to grinding wheel and metal sheet being ground. Cooling air reduces thermal distortion of workpiece due to localized frictional heating. Particularly useful when grinding sheet metal.
Electric gathering of sheet stock edges forms metal sheets in the shape of gore sections with heavier edge areas that can be welded without loss of strength. The edges are gathered by progressive resistance heating and upsetting, and are formed automatically. This process avoids disturbance of the metals internal structure.
Strength of sheet metal parts containing cracks studied by simulating fail safe design
This report presents a brief survey of the uses of sheet-metal coverings in conjunction with the inner structure. A method of construction is presented as well as a discussion on the strength of sheet metal.
Primacord which is woven through fish netting in a grid pattern is used for explosive forming of large sheet metal parts. The explosive force generated by the primacord detonation is uniformly distributed over the entire surface of the sheet metal workpiece.
Fiberglass tooling dies accelerate forming of large metal sheets. The dies, fabricated to fit over and fasten to the die bases, are lightweight, quickly replaced and have nongalling surfaces.
Direct lightning strikes melt metal parts of various systems, like fuel and propellant tanks of rockets and airplanes, at the point of strike. Responsible for this melting are the impulse current and, if occurring, the long duration current, both carrying a remarkable charge Q. For studying these meltings the simulation in the laboratory has to be based on the parameters of natural lightnings. International standards exist defining certain threat levels of natural lightnings and giving possible generator circuits for the simulation. The melting caused by both types of lightning currents show different appearance. Their characteristics, their differences in melting and heating of metal sheets are investigated. Nevertheless the simulation of lightning in the laboratory is imperfect. While natural lightning is a discharge without a counter electrode, the simulation always demands a close counter electrode. The influence of this counter electrode is studied.
Admittance of parallel plate waveguide aperture with infinite flange illuminating metal sheet, using wedge diffraction theory and integral transform method
The presence of cracks significantly decreases the structural integrity of thin metal sheets used in aerospace applications. Thermographic detection of surface temperature variations due to these cracks is possible after external heating. An approximate line source of heat is used to produce an inplane flow of heat in the sheet. A crack in the sheet perturbs the inplane flow of heat and can be seen in an image of the surface temperature of the sheet. An effective technique for locating these perturbations is presented which reduces the surface temperature image to an image of variations in the inplane heat flow. This technique is shown to greatly increase the detectability of the cracks. This thermographic method has advantages over other techniques in that it is able to remotely inspect a large area in a short period of time. The effectiveness of this technique depends on the shape, position and orientation of the heat source with respect to the cracks as well as the extent to which the crack perturbs the surface heat flow. The relationship between these parameters and the variation in the heat flow is determined both by experimental and computational techniques. Experimental data is presented for through-the-thickness, subsurface and surface EDM notches. Data for through-the-thickness fatigue cracks are also presented.
The object of this report was to develop the structural method of sheet metal girders and should for that reason be considered solely from this standpoint. The ensuing methods were based on the assumption of the infinitely low stiffness in bending of the metal web. This simplifies the basis of calculations to such an extent that many questions of great practical importance can be examined which otherwise cannot be included in any analysis of the bending stiffness of the buckled plate. This report refers to such points as the safety in buckling of uprights to the effect of bending flexibility of spars, to spars not set parallel, etc.
Fabrication of lightweight turbine components for M-1 engine oxidizer turbopump using electron beam welding for attaching sheet metal blades to discs and shrouds
An isotropic sheet stiffened by means of an orthotropic quarter-plate is considered. The quarter-plate is assumed to be perfectly bonded to the metal sheet everywhere except an area of debonding which may develop due to high stress concentrations. The adhesive which has a small constant thickness is treated as a shear spring. The loads are applied at infinity and supposed to be transmitted through the metal plate. Shear stress distribution between the two plates was obtained from the continuity of displacements along an area where they were bonded to each other.
The main material properties affecting the explosive weldability of a certain metal combination are the yield strength, the ductility, the density and the sonic velocity of the two metals. Successful welding of the metal combination depends mainly on the correct choice of the explosive welding parameters; i.e., the stand off distance, the weight of the explosive charge relative to the weight of the flyer plate and the detonation velocity of the explosive. Based on the measured and the handbook values of the properties of interest, the explosive welding parameters were calculated and the arrangements for the explosive welding of the Al alloy 6061-T6, titanium and zirconium to OFHC copper were determined. The relatively small sheet metal thickness (1/8") and the fact that the thickness of the explosive layer must exceed a certain minimum value were considered during the determination of the explosive welding conditions. The results of the metallographic investigations and the measurements of the shear strength at the interface demonstrate the usefulness of these calculations to minimize the number of experimental trials.