Search NASA⌕ Search

SEARCH · Search NASA

Results for “SIGNAL FORMAT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

A coherent digital demodulator for multiple signal formats and widely varying data rates

The Tracking and Data Relay Satellite System (TDRSS) uses four ground station demodulators for K-band signals with data rates from 1 kb/s to 300 Mb/s. The author discusses the feasibility of replacing these demodulators with a single digital demodulator that may be reconfigured by altering stored parameters to accommodate all signal formats and data rates. This implementation will reduce total ground station cost and facilitate automation of ground station operation. Analysis of system performance concentrates on the carrier tracking loop. Analytic and simulation results relate system performance to parameter values and signal format as data rate and power vary independently on the In-phase and quadrature channels. It is demonstrated that a single digital demodulator can support TDRSS-compatible signals at data rates conservatively extending from 1K symbols/s to 10M symbols/s, using off-the-shelf hardware with 6 or more bits of accuracy.

Mcguffin, Bruce F.↗
DOE OSTI2020

Effects of trapped charge on the signal formation and detection efficiency for subsequent pulses in irradiated silicon sensors

Envisaged high energy physics experiments like the Future Circular Collider require unprecedented radiation hardness of the detectors, as well as short readout time due to high luminosity and occupancy. Silicon has proven to be extremely radiation hard. Sufficient signals can be recorded even at fluences close to 1 ∙ 1 0 16 n e q / cm 2 . Here, the signal formation was studied in silicon strip sensors, irradiated and annealed until the phenomenon of charge multiplication occurred. ATLAS12EC R0 mini sensors were tested by means of edge TCT measurements at temperatures around –20 °C. It was observed that the detection of subsequent signals separated up to several microseconds is altered by the charge trapped during the preceding pulses. The effects of trapped charge on the electrical configuration of a sensor are well known as a polarization or pumping effect in larger band-gap materials like diamond, but is often neglected for silicon at this relatively high temperature. The investigation of the effect created by trapped charges in silicon sensors using subsequent pulses allows to gain information on important parameters such as de-trapping times. Furthermore, it shows a severe impact on the sensor performance in a pile-up scenario. The irradiation fluence and hence the effective doping concentration, the temperature and the amount of initially created charge have a large impact on this phenomenon. The measurements presented help to characterize this phenomenon; particular attention was paid to the application point of view.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

GPU-Accelerated Analytic Simulation of Sparse Ionization Signal Formation in Pixelated Projection Detector

This paper presents a GPU-accelerated simulation package, TRED, for next-generation neutrino detectors with pixelated charge readout, leveraging community-driven software ecosystems to ensure adaptability and extensibility. We introduce two generic contributions: (i) an effective-charge representation based on Gaussian quadrature rules, in which the linear- interpolation factors for the field response inside each voxel are absorbed into the effective charge, and (ii) a sparse, block- binned tensor representation that enables efficient FFT-based computation of induced signals on readout electrodes for sparsely activated detector volumes. The former captures structure inside a voxel without dense sampling, while the latter achieves low memory usage and scalable runtime, as demonstrated in bench- mark studies. The underlying data representation is applicable to large-scale detectors and to other computational problems involving sparse activity.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Signal formation and sharing in AC-LGADs using the ALTIROC 0 front-end chip

The development of detectors that provide high resolution in four dimensions has attracted wide-spread interest in the scientific community for applications in high-energy physics, nuclear physics, medical imaging, mass spectroscopy as well as quantum information. However, finding a technology capable of fulfilling such aspiration proved to be an arduous task. Among other silicon-based candidates, the Low-Gain Avalanche Diode (LGAD) has already shown excellent timing performances but proved to be unsuitable for fine pixelization. Therefore, the AC-coupled LGAD (AC-LGAD) approach was introduced to provide high resolution in both time and space, making it a promising candidate for future 4D detectors. However, appropriate readout electronics must be developed to match the sensor's fast-time and fine-pitch capabilities. This is currently a major technological challenge. Here, we test AC-LGAD prototypes read out by the fast-time ASIC ALTIROC 0, originally developed for the readout of DC-coupled LGADs for the ATLAS experiment at the High Luminosity-LHC. Signal generated by either betas from a 90 Sr source or a focused infra-red laser were analyzed. This paper details the first successful readout of an AC-LGAD sensor using a readout chip. This result will pave the way for the design and construction of a new generation of AC-LGAD-based 4D detectors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

LOXG473A induces the formation of osteoclasts in RAW264.7 cells via IL-6/JAK2/STAT3 signaling

Formation of osteoclasts is known to be closely associated with osteoporosis progression. LOX is a key enzyme that catalyzes the synthesis of collagen, which is the new mediator in osteoclast formation. However, the effect of LOXG473A on of osteoclast formation needs to be explored. Thereby, we sought to explore the effect of LOX{sub G473A} on formation of osteoclasts and its underlying mechanism. To investigate the function of LOX{sub G473A} in osteoclast formation, Raw264.7 cells were stably transfected with LOX-WT or LOX-MUT (LOX{sub G473A}). Real-time PCR and western blotting were used to detect the relative levels of osteoclast formation related genes and proteins. TRAP staining and immunofluorescence staining were used to test the ability of Raw264.7 cells to form osteoclasts and the ability of cells to form rings, respectively. Bone erosion assay was used to test bone resorptive activity. The data indicated that LOX{sub G473A} significantly enhanced the ability of osteoclasts forming, ring-forming and bone resorpting in Raw264.7 cells. Mechanically, LOX{sub G473A} upregulated the expressions of NFATC1, ACP5, CTSK, IL-6, and the proportion of p-JAK2/JAK2 and p-STAT3/STAT3, thereby promoting the formation of osteoclasts. In conclusion, we have verified that LOX{sub G473A} induces the proliferation of osteoclasts in Raw264.7 cells via IL-6/JAK2/STAT3 signaling, suggesting a novel strategy for studying osteoporosis.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1976

Possible methods for USSR-VLF navigation receivers

The U.S.S.R. has a VLF navigation system similar to OMEGA. Beukers has reported some information on the signal format, frequencies used, and the probable radiated power levels. From this data it appears possible to derive receiver operation modes and some implied reasons for the unique choice of the time-multiplexed frequency time base used. Of interest are receiver methods requiring processor gate complexity similar to a digital wristwatch including the use of mass-produced low frequency quartz crystal reference oscillators. The stability required of the local reference oscillator is probably much less critical than for other VLF receivers because of the signal format. One conclusion is that U.S.S.R.-VLF receivers might be fabricated at quite low cost making it possible for all persons in remote areas each to have his own private positioning aid. Further study of the actual transmitted signal format is warranted. While the nature of this memorandum is speculative because of the lack of confirming data, the receiver method proposed has evolved from related principles which have been applied to the operating OMEGA-VLF navigation system.

Burhans, R. W.↗
NASA NTRS1985

Direct-detection optical communication with color coded pulse position modulation signaling

The performance characteristics of a direct-detection optical communication system which is based on a laser transmitter which produces single light pulses at selected nonoverlapping optical center frequencies are discussed. The signal format, called color coded pulse position modulation (CCPPM), uses more of the total available response bandwidth characteristics of the photodetector than does ordinary PPM signaling. The advantages of CCPPM signaling are obtained at the expense of an increased optical bandwidth of the transmitted signal and a more complicated transmitter and receiver structure. When the signal format is used in conjunction with block length Reed-Solomon codes, high data rates and reliable high-speed optical communications under conditions of optimal energy efficiency are obtained.

Davidson, F.↗
NASA NTRS1989

Optical Communication with Semiconductor Laser Diode

Theoretical and experimental performance limits of a free-space direct detection optical communication system were studied using a semiconductor laser diode as the optical transmitter and a silicon avalanche photodiode (APD) as the receiver photodetector. Optical systems using these components are under consideration as replacements for microwave satellite communication links. Optical pulse position modulation (PPM) was chosen as the signal format. An experimental system was constructed that used an aluminum gallium arsenide semiconductor laser diode as the transmitter and a silicon avalanche photodiode photodetector. The system used Q=4 PPM signaling at a source data rate of 25 megabits per second. The PPM signal format requires regeneration of PPM slot clock and word clock waveforms in the receiver. A nearly exact computational procedure was developed to compute receiver bit error rate without using the Gaussion approximation. A transition detector slot clock recovery system using a phase lock loop was developed and implemented. A novel word clock recovery system was also developed. It was found that the results of the nearly exact computational procedure agreed well with actual measurements of receiver performance. The receiver sensitivity achieved was the closest to the quantum limit yet reported for an optical communication system of this type.

Davidson, Frederic↗
DOE OSTI2025

Long-lived neutron-star remnants from asymmetric binary neutron star mergers: element formation, kilonova signals and gravitational waves

We present 3D general-relativistic neutrino-radiation hydrodynamics simulations of two asymmetric binary neutron star mergers producing long-lived neutron stars remnants and spanning a fraction of their cooling time scale. The mergers are characterized by significant tidal disruption with neutron rich material forming a massive disc around the remnant. The latter develops one-armed dynamics that is imprinted in the emitted kilo-Hertz gravitational waves. Angular momentum transport to the disc is initially driven by spiral-density waves and enhanced by turbulent viscosity and neutrino heating on longer timescales. The mass outflows are composed by neutron-rich dynamical ejecta of mass ∼10 −3 –10 −2 M ⊙ followed by a persistent spiral-wave/neutrino-driven wind of ≳ 10 −2 M ⊙ with material spanning a wide range of electron fractions, ∼0.1–0.55. Dynamical ejecta (winds) have fast velocity tails up to ∼0.8 (∼0.4) c. The outflows are further evolved to days timescale using 2D ray-by-ray radiation-hydrodynamics simulations that include an online nuclear network. We find complete r-process yields and identify the production of 56 Ni and the subsequent decay chain to 56 Co and 56 Fe. Synthetic kilonova light curves predict an extended (near-) infrared peak a few days postmerger originating from r-process in the neutron-rich/high-opacity ejecta and UV/optical peaks at a few hours (ten minutes) postmerger originating from weak r-process (free-neutron decay) in the faster ejecta components. Additionally, the fast tail of tidal origin generates kilonova afterglows potentially detectable in radio and X band on a few to ten years time scale. Quantitative effects originating from the tidal disruption merger dynamics are reflected in the multimessenger emissions.

abundances↗
NASA NTRS1974

Anti-multipath digital signal detector

Detector operates in conjunction with radio frequency portion of receiver to detect digital signals transmitted in known modulation formats. Signal is constructed by assigning known and distinct modulation waveforms to sequence of message symbols. It reconstructs transmitted digital sequence with minimum probability that any reconstructed digit will be in error.

Painter, J. H.↗
NASA NTRS1979

Spectral characteristics of convolutionally coded digital signals

The power spectral density of the output symbol sequence of a convolutional encoder is computed for two different input symbol stream source models, namely, an NRZ signaling format and a first order Markov source. In the former, the two signaling states of the binary waveform are not necessarily assumed to occur with equal probability. The effects of alternate symbol inversion on this spectrum are also considered. The mathematical results are illustrated with many examples corresponding to optimal performance codes.

Divsalar, D.↗
NASA NTRS1975

Graphical derivations of radar, sonar, and communication signals

The designer of a communication system often has knowledge concerning the changes in distance between transmitter and receiver as a function of time. This information can be exploited to reduce multipath interference via proper signal design. A radar or sonar may also have good a priori information about possible target trajectories. Such knowledge can again be used to reduce the receiver's response to clutter (MTI), to enhance signal-to-noise ratio, or to simplify receiver design. There are also situations in which prior knowledge about trajectories is lacking. The system should then utilize a single-filter pair which is insensitive to the effects induced by relative motion between transmitter, receiver, and reflectors. For waveforms with large time-bandwidth products, such as long pulse trains, it is possible to graphically derive signal formats for both situations (trajectory known and unknown). Although the exact form of the signal is sometimes not specified by the graphical procedure, the problem in such cases is reduced to one which has already been solved, i.e., the generation of an impulse equivalent code.

Altes, R. A.↗
NASA NTRS1993

A hybrid voice/data modulation for the VHF aeronautical channels

A method of improving the spectral efficiency of the existing Very High Frequency (VHF) Amplitude Modulation (AM) voice communication channels is proposed. The technique is to phase modulate the existing voice amplitude modulated carrier with digital data. This allows the transmission of digital information over an existing AM voice channel with no change to the existing AM signal format. There is no modification to the existing AM receiver to demodulate the voice signal and an additional receiver module can be added for processing of the digital data. The existing VHF AM transmitter requires only a slight modification for the addition of the digital data signal. The past work in the area is summarized and presented together with an improved system design and the proposed implementation.

Akos, Dennis M.↗
NASA NTRS1990

A description of QUALCOMM Automatic Satellite Position Reporting (QASPR(R)) for mobile communications

Two satellite position reporting has been introduced into the OmniTRACS mobile satellite communication system. This system significantly improves position reporting reliability and accuracy while simplifying the terminal's hardware. The positioning technique uses the original OmniTRACS TDMA timing signal formats in the forward and return link directions plus an auxiliary, low power forward link signal through a second satellite to derive distance values. The distances are then converted into the mobile terminal's latitude and longitude in real time. A minor augmentation of the spread spectrum profile of the return link allowed the resolution of periodic ambiguities. The system also locates the two satellites in real time with fixed platforms in known locations using identical mobile terminal hardware. Initial accuracies of 1/4 mile have been realized uniformly throughout the USA using a satellite separation of 22 degrees and there are no dead zones, skywaves, or cycle slips as found in terrestrial systems like LORAN-C.

Ames, William G.↗
NASA NTRS1979

Carrier phase recovery performance for PN-spread TDRSS link with radio-frequency interference

The carrier-phase recovery performance of a Costas loop for a nonlinear satellite channel with uplink and downlink noise is analyzed, and the extension of these results to the case where uplink radio-frequency interference (RFI) is present is considered. The signal format here is binary phase-shift-keyed (BPSK) or unbalanced quaternary phase-shift-keyed (UQPSK), the signals being either the non-return-to-zero (NRZ) or biphase (Manchester) type. With UQPSK, at least one data stream must be PN-spread. The channel comprises additive white Gaussian noise (WGN), a wideband filter, a bandpass nonlinearity and more additive WGN. The RFI being considered is pulsed continuous-wave, pulsed WGN, or a combination of the two. It is noted that the Tracking and Data Relay Satellite System (TDRSS) will be subjected to RFI from certain locations, especially in the S-band of frequencies. The characteristics of this link are generalized to form the assumptions underlying this analysis. The analytical results given include the S-curve of the equivalent loop and the phase-error variance of the linearized loop.

Mckenzie, T. M.↗
NASA NTRS2013

Simultaneous Laser Ranging and Communication from an Earth-Based Satellite Laser Ranging Station to the Lunar Reconnaissance Orbiter in Lunar Orbit

We report a free space laser communication experiment from the satellite laser ranging (SLR) station at NASA Goddard Space Flight Center (GSFC) to the Lunar Reconnaissance Orbiter (LRO) in lunar orbit through the on board one-way Laser Ranging (LR) receiver. Pseudo random data and sample image files were transmitted to LRO using a 4096-ary pulse position modulation (PPM) signal format. Reed-Solomon forward error correction codes were used to achieve error free data transmission at a moderate coding overhead rate. The signal fading due to the atmosphere effect was measured and the coding gain could be estimated.

fee-space optical communication↗
NASA NTRS2013

Performance Evaluation of Large Aperture 'Polished Panel' Optical Receivers Based on Experimental Data

Recent interest in hybrid RF/Optical communications has led to the development and installation of a "polished-panel" optical receiver evaluation assembly on the 34-meter research antenna at Deep-Space Station 13 (DSS-13) at NASA's Goldstone Communications Complex. The test setup consists of a custom aluminum panel polished to optical smoothness, and a large-sensor CCD camera designed to image the point-spread function (PSF) generated by the polished aluminum panel. Extensive data has been obtained via realtime tracking and imaging of planets and stars at DSS-13. Both "on-source" and "off-source" data were recorded at various elevations, enabling the development of realistic simulations and analytic models to help determine the performance of future deep-space communications systems operating with on-off keying (OOK) or pulse-position-modulated (PPM) signaling formats with photon-counting detection, and compared with the ultimate quantum bound on detection performance for these modulations. Experimentally determined PSFs were scaled to provide realistic signal-distributions across a photon-counting detector array when a pulse is received, and uncoded as well as block-coded performance analyzed and evaluated for a well-known class of block codes.

on-off keying (OOK)↗
NASA NTRS1971

Design and performance evaluation of a wideband FM spread-spectrum multiple-access system

The system described performs the tracking and communications functions of a tracking and data relay satellite system (TDRS). The spread-spectrum signal format is achieved through wide deviation FM by a sinusoidal subcarrier unique to each multiple-access user. A compound phase-locked loop tracks carrier and subcarrier and demodulates data and ranging signals. Design parameters of user and ground terminals for TDRS are given. Acquisition procedures are described. Performance analyses are presented including the effects of noise, RFI, multipath and other users.

Wachsman, R. H.↗