Search NASA⌕ Search

SEARCH · Search NASA

Results for “SKID LANDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Skid Landings of Airplanes on Rocker-Type Fuselages

A study is made of the landing of an airplane on a fuselage with "planned" curvature of its lower surface. Initial contact is considered to stop the vertical motion of a point remote from the center of gravity, thus causing rocking on the curved lower surface which converts sinking-speed energy into angular energy in pitch for dissipation by damping forces. Analysis is made of loads and motions for a given fuselage shape, and the contours required to give desired load histories are determined. Most of the calculations involve initial contact at the tail, but there are two cases of unflared landings with initial contact at the nose. The calculations are checked experimentally for the tail - low case.

Mayo, Wilbur L.↗
NASA NTRS2000

X-38 Landing Gear Skid Test Report

NASA incorporates skid-equipped landing gear on its series of X-38 flight test vehicles. The X-38 test program is the proving ground for the Crew Return Vehicle (CRV) a gliding parafoil-equipped vehicle designed to land at relatively low speeds. The skid-equipped landing gear is designed to attenuate the vertical landing energy of the vehicle at touchdown using crushable materials within the struts themselves. The vehicle then slides out as the vehicle horizontal energy is dissipated through the skids. A series of tests was conducted at Edwards Airforce Base (EAFB) in an attempt to quantify the drag force produced while "dragging" various X-38 landing gear skids across lakebed regions of varying surface properties. These data were then used to calculate coefficients of friction for each condition. Coefficient of friction information is critical for landing analyses as well as for landing gear load and interface load analysis. The skid specimens included full- and sub-scale V201 (space test vehicle) nose and main gear designs, a V131/V 132 (atmospheric flight test vehicles) main gear skid (actual flight hardware), and a newly modified, full-scale V201 nose -ear skid with substantially increased edge curvature as compared to its original design. Results of the testing are discussed along with comments on the relative importance of various parameters that influence skid stability and other dynamic behavior.

Gafka, George K.↗
NASA NTRS1978

Summary of NASA landing-gear research

This paper presents a brief summary of the airplane landing gear research underway at NASA. The technology areas include: ground handling simulator, antiskid braking systems, space shuttle nose-gear shimmy, active control landing gear, wire brush skid landing gear, air cushion landing systems, tire/surface friction characteristics, tire mechanical properties, tire-tread materials, powered wheels for taxiing, and crosswind landing gear. This paper deals mainly with the programs on tire-tread materials, powered wheel taxiing, air cushion landing systems, and crosswind landing gear research with particular emphasis on previously unreported results of recently completed flight tests. Work in the remaining areas is only mentioned.

Fisher, B. D.↗
NASA NTRS1964

Dynamic Model Investigation of the Landing Characteristics of a Manned Spacecraft

Investigations were made to study the water-landing and certain grounds-surface landing characteristics of a Gemini spacecraft model. The water landing experiments were made by simulating paraglider and parachute letdowns with two 1/6- scale model configurations. Parameters included various combinations of attitude, horizontal speed, vertical speed, and landing skids extended and retracted. Investigations were made in calm water and in waves. The paraglider landings at horizontal speeds of 63 feet per second (19.8 m/sec) which resulted in a noseover or tumbling shortly after initial water contact. The maximum longitudinal acceleration of the model in calm water was about 14g units, and the maximum angular acceleration was 66 radians per second squared. In the parachute landings with the heat shield forward, the model skidded along the water surface on the heat shield. Parachute landings with the small end forward resulted in behavior similar to that of the paraglider landings. The ground-surface landings were made with a 1/3-scale model by simulating a parachute letdown with braking rockets, which were fired prior to touchdown to dissipate vertical velocity. In these landings, control of timing and aligning the rockets on the model was very critical, and violent behavior resulted when either rocket alignment or timing was in error. In the landings that were correctly controlled, the model either remained upright or slowly rolled over on its side.

EXPERIMENTS↗
NASA NTRS1953

Measurements obtained during the glide-flight program of the Bell X-2 research airplane

Results obtained during the glide-flight program of the Bell X-2 research airplane are presented. Landing characteristics and limited data evaluating static longitudinal stability at low speeds are included. The data indicated positive static longitudinal stability in unaccelerated flight from indicated airspeeds of 152 to 178 miles per hour for the clean configuration, between 142 and 171 miles per hour with the flaps up and gear extended, and between 142 and 204 miles per hour with flaps and gear extended. A region of neutral stability, both stick fixed and stick free, was apparent between 178 and 192 miles per hour for the clean configuration. Data obtained during a turn made at an indicated airspeed of approximately 235 miles per hour with steadily increasing acceleration indicated positive stick-free and stick-fixed longitudinal stability. Stick force per unit normal acceleration was approximately 15 pounds. Pilots' notes indicated that dynamic stability in each plane of reference was apparently positive with satisfactory damping for the speed range covered. The main landing-skid surface area was enlarged 300 percent for flights 2 and 3 with a resulting improvement in landing characteristics. Average longitudinal deceleration during the ground run was decreased from 0.7 unit of acceleration for flight 1 to a value of 0.3 unit of acceleration for flights 2 and 3. Normal acceleration at the nose wheel was correspondingly reduced from 4 to 2.8 units of acceleration. The addition of inboard wing skids prevented rolling onto a wing tip during ground run.

Richard E Day↗
NASA NTRS1990

Supersonic combustion engine testbed, heat lightning

The design of a supersonic combustion engine testbed (SCET) aircraft is presented. The hypersonic waverider will utilize both supersonic combustion ramjet (SCRAMjet) and turbofan-ramjet engines. The waverider concept, system integration, electrical power, weight analysis, cockpit, landing skids, and configuration modeling are addressed in the configuration considerations. The subsonic, supersonic and hypersonic aerodynamics are presented along with the aerodynamic stability and landing analysis of the aircraft. The propulsion design considerations include: engine selection, turbofan ramjet inlets, SCRAMjet inlets and the SCRAMjet diffuser. The cooling requirements and system are covered along with the topics of materials and the hydrogen fuel tanks and insulation system. A cost analysis is presented and the appendices include: information about the subsonic wind tunnel test, shock expansion calculations, and an aerodynamic heat flux program.

Hoying, D.↗
NASA NTRS1950

Tests of a Northrop XSSM-A-3 Missile in the Ames 40- by 80-Foot Wind Tunnel: Stability and Control

This report presents the results of wind-tunnel force tests which were conducted to determine the low-speed stability and control characteristics of a full-scale Northrop XSSM-A-3 missile. Tests were made through a range of angles of attack, sideslip, and control deflection, and at various Reynolds numbers. Characteristics of the complete missile are compared with the characteristics of the missile with the landing skids extended, with the vertical tail removed, and with the fuselage alone. No analysis of the data has been made in order to make the results available as soon as possible.

Maki, Ralph L.↗
NASA NTRS1952

First Landing of Bell X-2 Research Airplane

The Bell X-2 supersonic research airplane is equipped with a skid main landing gear and a nose wheel. Pending completion of the rocket engine, glide flights are being performed to determine low-speed handling qualities of the airplane and the landing characteristics with the skid-type landing gear. The present paper presents data obtained during the approach and landing of the X-2 airplane on its first flight .

Richard E. Day↗
NASA NTRS1961

Considerations of Methods of Improving Helicopter Efficiency

Recent NASA helicopter research indicates that significant improvements in hovering efficiency, up to 7 percent, are available from the use of a special airfoil section formed by combining an NACA 632A015 thickness distribution with an NACA 230 mean line. This airfoil should be considered for flying-crane-type helicopters. Application of standard leading-edge roughness causes a large drop in efficiency; however, the cambered rotor is shown to retain its superiority over a rotor having a symmetrical airfoil when both rotors have leading-edge roughness. A simple analysis of available rotor static-thrust data indicates a greatly reduced effect of compressibility effects on the rotor profile-drag power than predicted from calculations. Preliminary results of an experimental study of helicopter parasite drag indicate the practicability of achieving an equivalent flat-plate parasite-drag area of less than 4 square feet for a rotor-head-pylon-fuselage configuration (landing gear retracted) in the 2,000-pound minimum-flying-weight class. The large drag penalty of a conventional skid-type landing (3.6 square feet) can be reduced by two-thirds by careful design. Clean, fair, and smooth fuselages that tend to have narrow, deep cross sections are shown to have advantages from the standpoint of drag and download. A ferry range of the order of 1,500 miles is indicated to be practicable for the small helicopter considered.

Dingeldein, Richard C.↗