SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Calculation of a thick solenoid coils magnetic field components is made by a superposition of the fields produced by four solenoids of infinite length and zero inner radius. The field produced by this semi-infinite solenoid is dependent on only two variables, the radial and axial field point coordinates.
Calculating magnetic field components in or around thick finite solenoid
Superposition method for calculating the magnetic field components of thick finite solenoids
Design optimization of power solenoids for controllable and stabilizable magnetic suspensions with force compensation in a wind tunnel is shown. It is assumed that the model of a levitating body is a sphere of ferromagnetic material with constant magnetic permeability. This sphere, with a radius much smaller than its distance from the solenoid above, is to be maintained in position on the solenoid axis by balance of the vertical electromagnetic force and the force of gravitation. The necessary vertical (axial) force generated by the solenoid is expressed as a function of relevant system dimensions, solenoid design parameters, and physical properties of the body. Three families of curves are obtained which depict the solenoid power for a given force as a function of the solenoid length with either outside radius or inside radius as a variable parameter and as a function of the outside radius with inside radius as a variable parameter. The curves indicate the optimum solenoid length and outside radius, for minimum power, corresponding to a given outside radius and inside radius, respectively.
A proposed design for a solenoid-based electromechanical actuator would provide greater starting force than does a comparable conventional design. As used here, starting force signifies the magnetic force exerted by the actuator at one end of its stroke when the gap in its magnetic circuit is the widest. A solenoid of conventional design exerts a large force when its gap is closed. The magnetic force decreases as the gap increases. Hence, typically, the starting force exerted by a conventional solenoid is small; depending upon the specific application, the starting force may even be insufficient to initiate closure. Whereas a conventional solenoid design provides for only one core, the proposed design calls for three cores, two of these being fixed to one another with a separate core between these two. Analysis shows that in comparison with conventional solenoids, the solenoids of the proposed design would not have a cost impact, could have longer operational lives, and exhibit larger forces in an open position. It was also reported that the proposed design could be extended to multiple-staged solenoid design, which would yield increased force in the middle of the stroke as well.
Two concentric superconducting solenoids, one rotating, the other stationary are analyzed for energy storage in space. Energy is transferred from the rotating mass through a shaft coupled to a motor-generator. The inner windings interact with the magnetic field of the outer solenoid to cancel the centrifugal and self-field forces of the flywheel rim. Current is induced in the inner solenoid thus requiring no separate power supply, while the current in the outer solenoid must vary with the angular velocity of the flywheel. The effect of the gap and scaling laws are developed. The efficiency in energy per unit mass is marginally attractive.
A solenoid valve is described in which both an inlet and an outlet of the valve are sealed when the valve is closed. This double seal compensates for leakage at either the inlet or the outlet by making the other seal more effective in response to the leakage and allows the reversal of the flow direction by simply switching the inlet and outlet connections. The solenoid valve has a valve chamber within the valve body. Inlet and outlet tubes extend through a plate into the chamber. A movable core in the chamber extends into the solenoid coil. The distal end of the core has a silicone rubber plug. Other than when the solenoid is energized, the compressed spring biases the core downward so that the surface of the plug is in sealing engagement with the ends of the tubes. A leak at either end increases the pressure in the chamber, resulting in increased sealing force of the plug.
New design is proposed for ferrofluidic solenoid with low magnetic flux leakage. Solenoid consists of a coil centered within a football-shaped elastomeric capsule filled with a ferromagnetic fluid. Fluid replaces the solid, movable core of conventional solenoids, and elastomeric capsule acts as return spring.
The development of a solenoid valve failure detection system is described. The technique requires the addition of a radioactive gas to the propellant of a cold gas jet attitude control system. Solenoid failure is detected with an avalanche radiation detector located in the jet nozzle which senses the radiation emitted by the leaking radioactive gas. Measurements of carbon monoxide leakage rates through a Mariner type solenoid valve are presented as a function of gas activity and detector configuration. A cylindrical avalanche detector with a factor of 40 improvement in leak sensitivity is proposed for flight systems because it allows the quantity of radioactive gas that must be added to the propellant to be reduced to a practical level.
The results of experimental demonstrations of a superconducting solenoid model core in the Southampton University Magnetic Suspension and Balance System are detailed. Technology and techniques relevant to large-scale wind tunnel MSBSs comprise the long term goals. The magnetic moment of solenoids, difficulties peculiar to superconducting solenoid cores, lift force and pitching moment, dynamic lift calibration, and helium boil-off measurements are discussed.
The superconducting solenoid model is a pilot model core for levitation in a wind tunnel magnetic suspension system. This type of core would replace the ferromagnetic core typically installed in the model fuselage. For suspension purposes, the solenoid is operated upon by a set of electromagnets surrounding the wind tunnel which are to support and restrain the model at required positions and orientations under the influence of powerful aerodynamic disturbances. The subject of providing sources of magnets rolling moment for use when spanwise magnets, which can be used for winged models, are not available is covered. Several methods have emerged for generating a rolling moment based on the use of additional superconducting loops or magnetic poles positioned around or within the solenoid. Predictions of the moment capacities of superconducting loops in models sized for a large wind tunnel are presented. An existing prototype superconducting model proved a suitable vehicle for demonstrating and calibrating, at a smaller scale, some of the other roll elements based on magnetic pole devices. Calibration data are included.
Compared with conventional ferromagnetic fuselage cores, superconducting solenoid cores appear to offer significant reductions in the projected cost of a large wind tunnel magnetic suspension and balance system. The provision of sufficient magnetic roll torque capability has been a long-standing problem with all magnetic suspension and balance systems; and the spanwise iron magnet scheme appears to be the most powerful system available. This scheme utilizes iron cores which are installed in the wings of the model. It was anticipated that the magnetization of these cores, and hence the roll torque generated, would be affected by the powerful external magnetic field of the superconducting solenoid. A preliminary study has been made of the effect of the superconducting solenoid fuselage model core concept on the spanwise iron magnet roll torque generation schemes. Computed data for one representative configuration indicate that reductions in available roll torque occur over a range of applied magnetic field levels. These results indicate that a 30-percent increase in roll electromagnet capacity over that previously determined will be required for a representative 8-foot wind tunnel magnetic suspension and balance system design.
Electrical properties of solenoids imitated for tests of control circuits. Simulation circuit imitates voltage and current responses of two engine-controlling solenoids. Used in tests of programs of digital engine-control circuits, also provides electronic interface with circuits imitating electrical properties of pressure sensors and linear variable-differential transformers. Produces voltages, currents, delays, and discrete turnon and turnoff signals representing operation of solenoid in engine-control relay. Many such circuits used simulating overall engine circuitry.
A tube-type shutoff valve is electrically positioned to its open or closed position by a concentric electromagnetic solenoid. The valve is dual latching in that the armature of the solenoid maintains the sliding tube of the valve in an open or closed position by means of permanent magnets which are effective when current is not supplied to the solenoid. The valve may also be actuated manually.
The axial and radial fields at any point inside or outside a finite solenoid with infinitely thin walls are derived. Solution of the equations has been obtained in terms of tabulated complete elliptic integrals. For the axial field an accurate approximation is given in terms of elementary functions. Fields internal and external to the solenoid are presented in graphical form for a wide variety of solenoid lengths.
Stop watch which may be remotely controlled by the use of a solenoid mechanism is described. When the solenoid is energized, the coil spring pulls the lever arm and starts the balance wheel. When it is not energized, the spring pulls the lever and stops the watch.
Holding solenoid uses residual magnetism to hold its armature in a desired position after excitation current is removed from the coil. Although no electrical power or mechanical devices are used, the solenoid has a low tolerance to armature displacement from the equilibrium position.
Operation of solenoid braking mechanism is discussed. Illustrations of construction of the brake are provided. Device is used for braking low or medium speed shaft rotations and produces approximately ten times braking torque of similar solenoid brakes.