SEARCH · Search NASA

Results for “SPAN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Low-speed aerodynamic performance of an aspect-ratio-10 supercritical-wing transport model equipped with a full-span slat and part-span and full-span double-slotted flaps

An investigation was conducted in the Langley 4 by 7 Meter Tunnel to determine the static longitudinal and lateral directional aerodynamic characteristics of an advanced aspect ratio 10 supercritical wing transport model equipped with a full span leading edge slat as well as part span and full span trailing edge flaps. This wide body transport model was also equipped with spoiler and aileron roll control surfaces, flow through nacelles, landing gear, and movable horizontal tails. Six basic wing configurations were tested: (1) cruise (slats and flaps nested), (2) climb (slats deflected and flaps nested), (3) part span flap, (4) full span flap, (5) full span flap with low speed ailerons, and (6) full span flap with high speed ailerons. Each of the four flapped wing configurations was tested with leading edge slat and trailing edge flaps deflected to settings representative of both take off and landing conditions. Tests were conducted at free stream conditions corresponding to Reynolds number of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle of attack range of 4 to 24, and a sideslip angle range of -10 deg to 5 deg. The part and full span wing configurations were also tested in ground proximity.

Morgan, H. L., Jr.↗

NASA NTRS1959

Low-Speed Wind-Tunnel Investigation to Determine the Aerodynamic Characteristics of a Rectangular Wing Equipped with a Full-Span and an Inboard Half-Span Jet-Augmented Flap Deflected 55 deg

An investigation to determine the aerodynamic characteristics of a rectangular wing equipped with a full-span and an inboard half-span jet-augmented flap has been made in the Langley 300 MPH 7- by 10-foot tunnel. The wing had an aspect ratio of 8.3 and a thickness-chord ratio of 0.167. A jet of air was blown backward through a small gap, tangentially to the upper surface of a round trailing edge, and was separated from the trailing edge by a very small flap at an angle of 55 deg with respect to the wing-chord plane. The results of the investigation showed that the ratio of total lift to jet-reaction lift for the wing was about 35 percent less for the half-span jet-augmented flap than for the full-span jet-augmented flap. The reduction of the span of the jet-augmented flap from full to half span reduced the maximum value of jet-circulation lift coefficient that could be produced from about 6.8 to a value of about 2.2. The half-span jet- augmented flap gave thrust recoveries considerably poorer than those obtained with the full-span jet-augmented flap. Large nose-down pitching- moment coefficients were produced by the half-span flap, with the greater part of these being the result of the larger jet reactions required to produce a given lift for the half-spin flap compared with that required for the full-span flap.

Gainer, Thomas G.↗

NASA NTRS1934

The effects of full-span and partial-span split flaps on the aerodynamic characteristics of a tapered wing

The investigation was made to determine the effects of full-span and of partial-span split flaps on the aerodynamic characteristics of a tapered wing. Aerodynamic force tests were made in the N.A.C.A. 7 by 10 foot wind tunnel on a highly tapered Clark Y wing equipped with various split flaps. Two sizes of tapered-chord flaps were tested as full-span flaps, and a narrow tapered-chord flap was tested as a partial-span flap by cutting off portions first from the tip and then from the center. The investigation showed that with full-span split flaps the lift and drag characteristics of the tapered wing up to the stall are similar to those of a rectangular wing with flaps of comparable size, but that the stall of the tapered wing with full-span flaps occurs at progressively lower angles of attack with increasing flap deflection up to that for maximum lift. For partial-span tapered split flaps on a tapered wing it was found that the maximum lift is greater, and the lift-drag ratio at maximum lift is less, when the partial-span flap is located at the center of the wing than when it is located at the tip portion.

Wenzinger, Carl J↗

NASA NTRS1978

Comparison of wing-span averaging effects on lift, rolling moment, and bending moment for two span load distributions and for two turbulence representations

An analytical method of computing the averaging effect of wing-span size on the loading of a wing induced by random turbulence was adapted for use on a digital electronic computer. The turbulence input was assumed to have a Dryden power spectral density. The computations were made for lift, rolling moment, and bending moment for two span load distributions, rectangular and elliptic. Data are presented to show the wing-span averaging effect for wing-span ratios encompassing current airplane sizes. The rectangular wing-span loading showed a slightly greater averaging effect than did the elliptic loading. In the frequency range most bothersome to airplane passengers, the wing-span averaging effect can reduce the normal lift load, and thus the acceleration, by about 7 percent for a typical medium-sized transport. Some calculations were made to evaluate the effect of using a Von Karman turbulence representation. These results showed that using the Von Karman representation generally resulted in a span averaging effect about 3 percent larger.

Lichtenstein, J. H.↗

NASA NTRS1937

Full Scale Span Load Distribution on a Tapered Wing with Split Flaps of Various Spans

Pressure-distribution tests were conducted in the full-scale wind tunnel on a 2:1 tapered U.S.A. 45 airfoil equipped with 20 percent chord split trailing-edge flaps of various spans. A special installation was employed in the tests utilizing a half-span airfoil mounted vertically above a reflection plane. The airfoil has a constant chord center section and rounded tips and is tapered in thickness from 18 percent c at the root to 9 percent c at the tip. The aerodynamic characteristics, given by the usual dimension less coefficients, are presented graphically as functions of flap span and angle of attack as well as by semispan load diagrams. The results indicate, in general, that only a relatively small increase in the normal-force coefficient is to be expected by extending the flap span of an airfoil-flap combination, similar to the one tested, beyond 70 percent of the wing span.

Parsons, John F↗

NASA NTRS1998

Buckling mode localization in a multi-span periodic structure with a disorder in a single span

This paper investigates the buckling mode localization in the periodic multi-span beam with disorder occurring in an arbitrary single span. The analytical finite difference calculus is used in conjunction with the conventional displacement method to derive the transcendental equations from which buckling load is calculated. The underlying treatment is general and the solution thus obtained is exact. Numerical results show that the buckling mode is highly localized in the vicinity of the disordered span of the beam.

Li, Y. W.↗

NASA NTRS1979

Low-speed aerodynamic performance of a high-aspect-ratio supercritical-wing transport model equipped with full-span slat and part-span double-slotted flaps

An investigation was conducted in the Langley V/STOL tunnel to determine the static longitudinal and lateral-directional aerodynamic characteristics of an advanced high-aspect-ratio supercritical-wing transport model equipped with a full-span leading-edge slat and part-span double-slotted trailing-edge flaps. This wide-body transport model was also equipped with spoiler and aileron control surfaces, flow-through nacelles, landing gear, movable horizontal tails, and interchangeable wing tips with aspect ratios of 10 and 12. The model was tested with leading-edge slat and trailing-edge flap combinations representative of cruise, climb, takeoff, and landing wing configurations. The tests were conducted at free-stream conditions corresponding to Reynolds numbers (based on mean geometric chord) of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle-of-attack range of -2 deg to 24 deg and a sideslip-angle range of -10 deg to 5 deg.

Morgan, H. L., Jr.↗

NASA NTRS1990

The SPAN cookbook: A practical guide to accessing SPAN

This is a manual for remote users who wish to send electronic mail messages from the Space Physics Analysis Network (SPAN) to scientific colleagues on other computer networks and vice versa. In several instances more than one gateway has been included for the same network. Users are provided with an introduction to each network listed with helpful details about accessing the system and mail syntax examples. Also included is information on file transfers, remote logins, and help telephone numbers.

Mason, Stephanie↗

NASA NTRS1937

Span load distribution for tapered wings with partial-span flaps

Tables are given for determining the load distribution of tapered wings with partial-span flaps placed either at the center or at the wing tips. Seventy-two wing-flap combinations, including two aspect ratios, four taper ratios, and nine flap lengths, are included. The distributions for the flapped wing are divided into two parts, one a zero lift distribution due primarily to the flaps and the other an additional lift distribution due to an angle of attack of the wing as a whole. Comparison between theoretical and experimental results for wings indicate that the theory may be used to predict the load distribution with sufficient accuracy for structural purposes.

Pearson, H A↗

NASA NTRS1947