Accurate Modeling of Material Nonlinearities in a Wind Turbine Spar Cap.
Abstract not provided.
Clarke, Ryan↗
SEARCH · Search NASA
Results for “SPARS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)
The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.
42 ENGINEERING↗
Powering the Woods Hole X-Spar Buoy with Ocean Wave Energy—A Control Co-Design Feasibility Study
Despite its success in measuring air–sea exchange, the Woods Hole Oceanographic Institution’s (WHOI) X-Spar Buoy faces operational limitations due to energy constraints, motivating the integration of an energy harvesting apparatus to improve its deployment duration and capabilities. This work explores the feasibility of an augmented, self-powered system in two parts. Part 1 presents the collaborative design between X-Spar developers and wave energy researchers translating user needs into specific functional requirements. Based on requirements like desired power levels, deployability, survivability, and minimal interference with environmental data collection, unsuitable concepts are pre-eliminated from further feasibility study consideration. In part 2, we focus on one of the promising concepts: an internal rigid body wave energy converter. We apply control co-design methods to consider commercial of the shelf hardware components in the dynamic models and investigate the concept’s power conversion capabilities using linear 2-port wave-to-wire models with concurrently optimized control algorithms that are distinct for every considered hardware configuration. During this feasibility study we utilize two different control algorithms, the numerically optimal (but acausal) benchmark and the optimized damping feedback. We assess the sensitivity of average power to variations in drive-train friction, a parameter with high uncertainty, and analyze stroke limitations to ensure operational constraints are met. Our results indicate that a well-designed power take-off (PTO) system could significantly extend the WEC-Spar’s mission by providing additional electrical power without compromising data quality.
autonomous systems↗
Floating platform effects on power generation in spar and semisubmersible wind turbines
The design and financing of commercial-scale floating offshore wind projects require a better understanding of how power generation differs between newer floating turbines and well-established fixed-bottom turbines. In floating turbines, platform mobility causes additional rotor motion that can change the time-averaged power generation. In this work, OpenFAST simulations examine the power generated by the National Renewable Energy Laboratory's 5-MW reference turbine mounted on the OC3-UMaine spar and OC4-DeepCWind semisubmersible floating platforms, subjected to extreme irregular waves and below-rated turbulent inflow wind from large-eddy simulations of a neutral atmospheric boundary layer. For these below-rated conditions, average power generation in floating turbines is most affected by two types of turbine displacements: an average rotor pitch angle that reduces power, caused by platform pitch; and rotor motion upwind-downwind that increases power, caused by platform surge and pitch. The relative balance between these two effects determines whether a floating platform causes power gains or losses compared to a fixed-bottom turbine; for example, the spar creates modest (3.1%–4.5%) power gains, whereas the semisubmersible creates insignificant (0.1%–0.2%) power gains for the simulated conditions. Furthermore, platform surge and pitch motions must be analyzed concurrently to fully capture power generation in floating turbines, which is not yet universal practice. Finally, a simple analytical model for predicting average power in floating turbines under below-rated wind speeds is proposed, incorporating effects from both the time-averaged pitch displacement and the dynamic upwind-downwind displacements.
17 WIND ENERGY↗
Thermal Instability in the Manufacturing of Wind Turbine Blade Spar Caps
As wind turbine blades continue to scale in length and total mass, the acceptability of traditional approaches for the engineering of processes to build these products has reached a limit. The continued need to reduce the levelized cost of energy (LCOE) drives manufacturing cycle times lower and the net mass of critical components challenges even the most experienced fabricators to meet the quality requirements for safe operating performance over the 25-year design life of the blade. In trying to reduce cycle time for key components of wind turbines, manufacturers discovered occasional buckling of fibers in wind turbine blade spar caps. The cause of the buckling was unknown. The goal of this project was to show that a comprehensive simulation, which considered all of the physics of the VARTM process, could identify the cause of the fiber buckling in spar caps that has been observed during the manufacturing process. Ultimately, the simulation determined the manufacturing process and parameters could lead to significant compressive stresses in the fibers eventually causing buckling. Simulation results suggest that the stress introduced from friction is the largest source of compressive stress in the fibers, the stress from the weight of gravity is significant but secondary, and the compressive stress from cure shrinkage does not play a significant role in the buckling of fibers. This report provides details of the testing and simulation methodology used to identify the cause of the fiber buckling.
17 WIND ENERGY↗
Thermal Instability in the Manufacturing of Wind Turbine Blade Spar Caps – Phase 2
As the wind turbine industry continues to develop, the technology surrounding the design, development, and manufacturing of blades requires advancement as well. Wind turbine blades continue to increase in size, increasing the cost and time associated with manufacturing. Simulation driven manufacturing cycle design is required for the industry to maintain manufacturing schedules and optimize the manufacturing process. A recent effort to reduce the cycle time of wind blade spar caps encountered a recurring manufacturing defect during the exotherm and curing of the resin system after filling in the vacuum-assisted resin transfer molding (VARTM) process. Thermal waves developed in sections of the spar cap resulting in unacceptable part tolerances, requiring the parts to be thrown out. The first phase of this IACMI project focused on characterizing the fabric and epoxy system used in manufacturing and simulating the manufacturing process to determine the root cause of the thermal waves. The second phase of this project refined and validated the manufacturing simulations. The simulation workflow was then used to analyze multiple cure cycle options to determine if the thermal waves would appear. The estimated filling time from the filling simulation was shown to match well to experiment, and the temperature history from the curing simulation lined up well with experiment. This indicates that these simulations could be used to evaluate future curing cycles to be used with manufacturing. It is recommended that the distortion simulation work be completed for this project, as it would allow for further manufacturing cycle evaluation through the prediction of stresses and strains in the part. This could provide indicators of defects like the thermal waves seen in manufacturing earlier.
17 WIND ENERGY↗
Nested control co-design of a spar buoy horizontal-axis floating offshore wind turbine
Not Available
Bayat, Saeid↗
Accurate Modeling of Material Nonlinearities in a Wind Turbine Spar Cap.
Abstract not provided.
Ennis, Brandon↗
Oak Ridge National Laboratory Thermoplastic Composite Joining of Pultruded Continuous Fiber Spars for Multi-Functional Battery Enclosure
Oak Ridge National Laboratory (ORNL) worked with DowAksa Industry to investigate the potential of using PA66 material to produce larger composite parts, transcending the limitations of traditional presses. The project aimed to develop a suitable material for printing battery boxes using Nylon 66 infused with 40 wt.% carbon fiber, compatible with the ORNL Additive Manufacturing and Compression Molding (AM-CM) system. However, even with extensive work, it was concluded that the material is not compatible with the AMCM process and suitable for joining using compression technique. Main reason for the incompatibility were found to be very high crystallinity of the PA66 grade chosen for this work. To improve printability, a modifier (proprietary) was added to decrease crystallinity, but this led to reduced thermal stability and adhesion issues.
36 MATERIALS SCIENCE↗
Additive Manufacturing for Powering the Blue Economy Applications: A Tidal Turbine Blade Case Study: Preprint
As the marine renewable energy industry continues to expand, innovation in the manufacturing space must grow accordingly to reduce costs and ensure the economic feasibility of new technologies. Additive manufacturing, more commonly known as 3D printing, provides an alternative for rapid prototyping of marine hydrokinetic technologies, particularly supporting Powering the Blue Economy initiatives of the U.S. Department of Energy Water Power Technologies Office. This study explores the application of additive manufacturing in the development of marine hydrokinetic structures, focusing on material and printing method selection, design, and analysis of a 3D-printed spar for an axial-flow tidal turbine blade. Corrosion-resistant metals were deemed ideal due to the loads and harsh marine environment the blade would experience. Laser metal deposition methods were determined to be the most effective and scalable for the considered scale. The designed spar adapts its geometry to the blade - a feature uniquely suited to additive manufacturing - and is intended to serve as the blade's primary structural component. A finite element model was used to study stresses and deformations under loading conditions. The spar was manufactured using 316L stainless steel through direct energy deposition, and defects were assessed and recorded. Future efforts will include mechanical testing of the spar. This research establishes a benchmark process for using additive manufacturing in developing marine hydrokinetic structures, paving the way for future optimization and techno-economic analysis.
additive manufacturing↗
Nozzle assembly and method for forming nozzle assembly
A nozzle assembly is disclosed, including a CMC nozzle shell, a nozzle spar, and an endwall. The CMC nozzle shell includes a CMC composition and an interior cavity. The nozzle spar is partially disposed within the interior cavity and includes a metallic composition, a cross-sectional conformation, a plurality of spacers protruding from the cross-sectional conformation, the plurality of spacers contacting the CMC nozzle shell, and a spar cap. The endwall includes at least one surface in lateral contact with the spar cap and maintains a lateral orientation of the CMC nozzle shell and the nozzle spar relative to the endwall. The lateral orientation maintains a predetermined throat area of the nozzle assembly. A method for forming the nozzle assembly includes inserting the nozzle spar into the interior cavity, rotating the CMC nozzle shell and the nozzle spar laterally relative to the endwall, and maintaining the lateral orientation.
Hafner, Matthew Troy↗
Economic competitiveness of pultruded fiber composites for wind turbine applications
Pultrusion manufacturing of fiber reinforced polymers has been shown to yield some of the highest mechanical properties for unidirectional composites, having a high degree of fiber alignment with consistent performance. Pultrusions offer a low-cost manufacturing approach for producing unidirectional composites with a constant cross-section and are used in many applications, including spar caps of wind turbine blades. However, as an intermediate processing step for wind blades, the additional cost of manufacturing pultrusions must be accompanied by sufficient increases in mechanical performance and system benefits. Wind turbine blades are manufactured using vacuum-assisted resin transfer molding with infused unidirectional fiberglass or carbon pultrusions for the spar cap. Infused fiberglass composites are among the most cost-effective structural materials available and replacing this material in the cost-driven wind industry has proven challenging, where infused fiberglass spar caps are still the predominant material system in use. To evaluate alternative material systems in a pultruded composite form, it is necessary to understand the costs for this additional manufacturing step which are shown to add 33%–55% on top of the material costs. A pultrusion cost model has been developed and used to quantify cost sensitivities to various processing parameters. The mechanical performance for pultruded composites is improved versus resin-infusion manufacturing with a 17% increase in design strength at a constant fiber volume fraction, but also enables higher achievable fiber volume fractions. The cost-specific mechanical performance is compared as a function of processing parameters for pultruded composites to identify the opportunities for alternative material and manufacturing approaches for wind turbine spar caps. Finally, four materials are compared in a representative wind turbine blade model to assess the performance of pultruded carbon fiber systems and pultruded fiberglass relative to infused fiberglass, where the pultruded systems produce lower weight blades with various cost distinctions.
42 ENGINEERING↗
Optimized Carbon Fiber Composites in Wind Turbine Blade Design: Follow-On Studies
This project has identified opportunities to bring further reductions in the mass and cost of modern wind turbine blades through the use of alternative material systems and manufacturing processes. The fiber reinforced polymer material systems currently used by the wind industry have stagnated as the technology continues to mature and as a means to reduce risk while introducing new products with continually increasing blade lengths. However, as blade lengths continue to increase, the challenge of controlling blade mass becomes even more critical to enabling the associated levelized cost of energy reductions. Stiffer and stronger reinforcement fibers can help to resolve the challenges of meeting the loading demands while limiting the increase in weight, but these materials are substantially more expensive than the traditional E-glass fiber systems. One goal of this project and associated work is to identify pathways that improve the cost-effectiveness of carbon fiber such that it is the reinforcement of choice in the primary structural elements of wind blades. The use of heavy-tow textile carbon fiber material systems has been shown to reduce the blade mass by 30-31% when used in the spar cap and by up to 7% when used in edgewise reinforcement. A pultrusion cost model was developed to enable a material cost comparison that includes an accurate estimate of the intermediate manufacturing step of pultrusion for the carbon fiber composite. Material cost reductions were revealed in most cases for the heavy-tow textile carbon fiber compared to infused fiberglass. The use of carbon fiber in the edgewise reinforcement produced the most notable material cost reduction of 33% for the heavy-tow textile carbon fiber. The mass and cost savings observed when using carbon fiber in edgewise reinforcement demonstrate a clear opportunity of this design approach. A carbon fiber conversion cost model was expanded to include a characterization of manufacturing costs when using advanced conversion processes with atmospheric plasma oxidation. This manufacturing approach was estimated to reduce the cost of carbon fiber material systems by greater than 10% and can be used with textile carbon systems or traditional carbon fiber precursors. The pultrusion cost model was also used to assess the opportunity for using pultruded fiberglass in wind blades, studying conventional E-glass fiber reinforcement. When using pultruded fiberglass as the spar cap material for two design classifications, the blade weight was reduced by 6% and 9% compared to infused fiberglass. However, due to the relatively large share of the pultrusion manufacturing cost compared to fiber cost, the spar cap material cost increased by 12% and 7%. When considering the system benefits of reduced blade mass and potentially lower blade manufacturing costs for pultruded composites, there may be opportunity for pultruded E-glass in wind blade spar caps, but further studies are needed. There is a clearer outcome for using pultruded fiberglass in the edgewise reinforcement where it resulted in a blade mass reduction of 2% and associated reinforcement material cost reduction of 1% compared to infused E-glass. The use of higher performing glass fibers, such as S-glass and H-glass systems, will produce greater mass savings but a study is needed to assess the cost implications for these more expensive systems. The most likely opportunity for these high-performance glass fibers is in the edgewise reinforcement, where the increased strength will reduce the damage accumulation of this fatigue-driven component. The blade design assessments in this project characterize the controlling material properties for the primary structural components in the flapwise and edgewise directions for modern wind blades. The observed trends with low and high wind speed turbine classifications for carbon and glass fiber reinforced polymer systems help to identify where cost reductions are needed, and where improvements in mechanical properties would help to reduce the material demands.
17 WIND ENERGY↗
Feasibility Study of Developing Alternative Common-Cause Failure Model for Event Assessment
This report is a revision of the original report, INL/LTD-14-33376. The original report, which was a limited distribution to the Nuclear Regulatory Commission (NRC) only and not available to the public, was revised as this report for public distribution. The report presents the feasibility study of alternative common-cause failure (CCF) models that could be used for event assessment in the Standardized Plant Analysis Risk (SPAR) models. The current CCF model used by the SPAR models is the alpha factor model. The proposed alternative CCF models are the partial alpha factor model and general dependency model. These alternative CCF models are reviewed and compared to the current alpha factor model, with the partial alpha factor model being identified as the preferred CCF model that could be used for event assessment in the SPAR models.
21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
The HUNTER Dynamic Human Reliability Analysis Tool: Development of a Module for Performance Shaping Factors
Human Unimodel for Nuclear Technology to Enhance Reliability (HUNTER) is a framework to support dynamic human reliability analysis (HRA) in communication with a variety of methods and tools. In this paper, how we have developed one of the HUNTER modules, the individual module for evaluating performance shaping factors (PSFs), is introduced. The PSF refers to any factor that influences human performance such as workload or complexity. It has been used for highlighting human errors and adjusting the error probabilities in the existing HRA. We consider the eight PSFs suggested in the Standardized Plant Analysis Risk-HRA (SPAR-H) method, which is the representative HRA method widely used in the nuclear field. To support our dynamic modeling using the eight SPAR-H PSFs, we reviewed human performance literature and developed data-based mathematical models to rate and quantify PSFs in the context of dynamic HRA. We also design the individual module composed of the two functions: 1) the PSF qualification function that automatically or manually evaluates a PSF level, and 2) the PSF quantification function that dynamically or statically determines the PSF multiplier values and integrate them to adjust human error probabilities (HEPs). How each function works with the SPAR-H PSFs and how the PSFs adjust the HEPs are investigated through literature and discussed in this paper.
99 GENERAL AND MISCELLANEOUS↗
The HUNTER Dynamic Human Reliability Analysis Tool: Development of a Module for Performance Shaping Factors
The Human Unimodel for Nuclear Technology to Enhance Reliability (HUNTER) is a framework to support dynamic human reliability analysis (HRA) in communication with a variety of methods and tools. This paper explores how we developed one of the HUNTER modules: namely, the Individual module for evaluating performance shaping factors (PSFs). A PSF is any factor that influences human performance (e.g., workload or complexity). In the existing HRA, they are used to highlight human errors and adjust error probabilities. We consider the eight PSFs suggested in the Standardized Plant Analysis Risk-HRA (SPAR-H) method, a representative HRA method widely used in the nuclear field. To support our dynamic modeling using the eight SPAR-H PSFs, we reviewed the human performance literature and developed data-based mathematical models to rate and quantify PSFs in the context of dynamic HRA. We also designed the Individual module to consist of two functions: (1) the PSF qualification function for automatically or manually evaluating PSF levels, and (2) the PSF quantification function for dynamically or statically determining PSF multiplier values and integrating them to adjust human error probabilities (HEPs). How each function works in regard to the SPAR-H PSFs, and how the PSFs serve to adjust the HEPs, were investigated via literature review and are discussed in this paper.
99 GENERAL AND MISCELLANEOUS↗
Wave-powered water pump for upwelling in aquaculture: Numerical model and ocean test
Wave-powered upwelling can increase the productivity and survivability of several aquaculture species. This enhancement is due to transporting cold, nutrient-rich ocean water, typically found lower in the water column, to the surface. Macroalgaes, like kelp, exhibit increased growth from these altered conditions. The University of New Hampshire’s (UNH) wave-powered water pump (wave pump) is a point absorber wave energy converter (WEC) that uses ocean waves to create relative motion between a spar buoy and a concentric float which drives an internal pump. A numerical model of the wave pump was developed using WEC-Sim to predict device performance in the ocean. Wave pump performance was evaluated during a five day ocean test near Appledore Island in Maine in March 2023, where volumetric flow rate, relative distance between spar and float, and wave conditions were measured. These data were then used for numerical model validation. The ocean deployment recorded the device’s performance in a variety of sea states, with average significant wave heights up to 0.7 m. The ocean test data were compared to the WEC-Sim numerical model of the device with favorable results. Average values of device stroke period, stroke height, and flow rate agreed between the ocean test and model data to within approximately 16 to 22%. Furthermore, the validated numerical model provides a valuable tool for improving the design and developing a commercial-scale, wave-powered water pump for use in aquaculture.
16 TIDAL AND WAVE POWER↗