Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A Method for Producing a Shaped Contour Radiation Pattern Using a Single Shaped Reflector and a Single Feed

Eliminating the corporate feed network in shaped contour beam antennas will reduce the expense, weight, and RF loss of the antenna system. One way of producing a shaped contour beam without using a feed network is to use a single shaped reflector with a single feed element. For a prescribed contour beam and feed, an optimization method for designing the reflector shape is given. As a design example, a shaped reflector is designed to produce a continental U.S. coverage (CONUS) beam. The RF performance of the shaped reflector is then verified by physical optics.

Cherrette, A. R.↗
NASA NTRS1989

A method for producing a shaped contour radiation pattern using a single shaped reflector and a single feed

Eliminating the corporate feed network in shaped contour beam antennas will reduce the expense, weight, and RF loss of the antenna system. One way of producing a shaped contour beam without using a feed network is to use a single shaped reflector with a single feed element. For a prescribed contour beam and feed, an optimization method for designing the reflector shape is given. As a design example, a shaped reflector is designed to produce a continental U.S. coverage (CONUS) beam. The RF performance of the shaped reflector is then verified by physical optics.

Cherrette, Alan R.↗
NASA NTRS1996

Shape Control of Solar Collectors Using Shape Memory Alloy Actuators

Solar collectors that are focused on a central receiver are designed with a mechanism for defocusing the collector or disabling it by turning it out of the path of the sun's rays. This is required to avoid damaging the receiver during periods of inoperability. In either of these two cases a fail-safe operation is very desirable where during power outages the collector passively goes to its defocused or deactivated state. This paper is principally concerned with focusing and defocusing the collector in a fail-safe manner using shape memory alloy actuators. Shape memory alloys are well suited to this application in that once calibrated the actuators can be operated in an on/off mode using a minimal amount of electric power. Also, in contrast to other smart materials that were investigated for this application, shape memory alloys are capable of providing enough stroke at the appropriate force levels to focus the collector. Design and analysis details presented, along with comparisons to test data taken from an actual prototype, demonstrate that the collector can be repeatedly focused and defocused within accuracies required by typical solar energy systems. In this paper the design, analysis and testing of a solar collector which is deformed into its desired shape by shape memory alloy actuators is presented. Computations indicate collector shapes much closer to spherical and with smaller focal lengths can be achieved by moving the actuators inward to a radius of approximately 6 inches. This would require actuators with considerably more stroke and some alternate SMA actuators are currently under consideration. Whatever SMA actuator is finally chosen for this application, repeatability and fatigue tests will be required to investigate the long term performance of the actuator.

Lobitz, D. W.↗
NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 feet per second. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise. The total noise power generation was essentially the same for circular, slot, and plug nozzles of good aerodynamic shape. The noise radiation patterns were essentially the same for these nozzle shapes except near the nozzle exhaust axis.

Olsen, W. A.↗
NASA NTRS1988

Equilibrium shapes of rotating spheroids and drop shape oscillations

Recent work on the equilibrium shapes of a rotating spheroid and drop shape oscillations is reviewed. The related theoretical aspects of the equilibrium shapes of a rotating drop, the stability, shape oscillations, gravitational forces, and drop fission are examined. Experimental findings on figures of a rotating drop in an immiscible system, drop oscillations in an immiscible system, oscillations of a rotating drop, compound drop oscillations, and drop dynamics in space are addressed.

Wang, Taylor G.↗
NASA NTRS2004

Shaping off-axis metallic membrane reflectors using optimal boundary shapes and inelastic strains

This paper will describe a novel concept for constructing off-axis membrane reflector surfaces. Membrane reflectors have been extensively studied, including investigations into inflated lenticular architectures, shaping by spin casting, shaping using electrostatic forces, and shaping by evacuating behind a membrane surface stretched between circular or annular-shaped supports.

membrane↗
NASA NTRS1979

Shape integral method for magnetospheric shapes

A method is developed for calculating the shape of any magnetopause to arbitrarily high precision. The method uses an integral equation which is evaluated for a trial shape. The resulting values of the integral equation as a function of auxiliary variables indicate how close one is to the desired solution. A variational method can then be used to improve the trial shape. Some potential applications are briefly mentioned.

Michel, F. C.↗
NASA NTRS2010

Improvement in the Shape Memory Response of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy with Scandium Microalloying

A Ti(50.5)Ni(24.5)Pd25 high-temperature shape memory alloy (HTSMA) is microalloyed with 0.5 at. pct scandium (Sc) to enhance its shape-memory characteristics, in particular, dimensional stability under repeated thermomechanical cycles. For both Ti(50.5)Ni(24.5)Pd25 and the Sc-alloyed material, differential scanning calorimetry is conducted for multiple cycles to characterize cyclic stability of the transformation temperatures. The microstructure is evaluated using electron microscopy, X-ray diffractometry, and wavelength dispersive spectroscopy. Isobaric thermal cycling experiments are used to determine transformation temperatures, dimensional stability, and work output as a function of stress. The Sc-doped alloy displays more stable shape memory response with smaller irrecoverable strain and narrower thermal hysteresis than the baseline ternary alloy. This improvement in performance is attributed to the solid solution hardening effect of Sc.

Atli, K. C.↗
NASA NTRS2011

Shape Memory Characteristics of Ti(sub 49.5)Ni(sub 25)Pd(sub 25)Sc(sub 0.5) High-Temperature Shape Memory Alloy After Severe Plastic Deformation

A Ti(49.5)Ni25Pd25Sc(0.5) high-temperature shape memory alloy is thermomechanically processed to obtain enhanced shape-memory characteristics: in particular, dimensional stability upon repeated thermal cycles under constant loads. This is accomplished using severe plastic deformation via equal channel angular extrusion (ECAE) and post-processing annealing heat treatments. The results of the thermomechanical experiments reveal that the processed materials display enhanced shape memory response, exhibiting higher recoverable transformation and reduced irrecoverable strain levels upon thermal cycling compared with the unprocessed material. This improvement is attributed to the increased strength and resistance of the material against defect generation upon phase transformation as a result of the microstructural refinement due to the ECAE process, as supported by the electron microscopy observations.

Atli, K. C.↗
NASA NTRS2014

Shape Sensing Using a Multi-Core Optical Fiber Having an Arbitrary Initial Shape in the Presence of Extrinsic Forces

Shape of a multi-core optical fiber is determined by positioning the fiber in an arbitrary initial shape and measuring strain over the fiber's length using strain sensors. A three-coordinate p-vector is defined for each core as a function of the distance of the corresponding cores from a center point of the fiber and a bending angle of the cores. The method includes calculating, via a controller, an applied strain value of the fiber using the p-vector and the measured strain for each core, and calculating strain due to bending as a function of the measured and the applied strain values. Additionally, an apparent local curvature vector is defined for each core as a function of the calculated strain due to bending. Curvature and bend direction are calculated using the apparent local curvature vector, and fiber shape is determined via the controller using the calculated curvature and bend direction.

Rogge, Matthew D.↗
NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise.

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 ft/sec. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise.

Olsen, W. A.↗
NASA NTRS2008

A Faceted Shape Model Approach to Altimetry and Velocimetry for Irregularly Shaped Bodies

Range and velocity sensors based on lidar or radar with multiple beams are often used to measure the altitude and velocity, respectively, of a spacecraft above a targetbody. A difficulty that arises when navigating about small bodies such as asteroids or comets, is that the notion of altitude is largely obscured by the irregular shape of the target surface. This paper develops a method to incorporate the multibeam altimeter and Doppler velocimeter measurements into the on-board spacecraft state estimator by using information from a faceted shape model representation of the target body surface.

state estimation↗
NASA NTRS2012

Aeroelastic Modeling of Elastically Shaped Aircraft Concept via Wing Shaping Control for Drag Reduction

Lightweight aircraft design has received a considerable attention in recent years as a means for improving cruise efficiency. Reducing aircraft weight results in lower lift requirements which directly translate into lower drag, hence reduced engine thrust requirements during cruise. The use of lightweight materials such as advanced composite materials has been adopted by airframe manufacturers in current and future aircraft. Modern lightweight materials can provide less structural rigidity while maintaining load-carrying capacity. As structural flexibility increases, aeroelastic interactions with aerodynamic forces and moments become an increasingly important consideration in aircraft design and aerodynamic performance. Furthermore, aeroelastic interactions with flight dynamics can result in issues with vehicle stability and control. Abstract This paper describes a recent aeroelastic modeling effort for an elastically shaped aircraft concept (ESAC). The aircraft model is based on the rigid-body generic transport model (GTM) originally developed at NASA Langley Research Center. The ESAC distinguishes itself from the GTM in that it is equipped with highly flexible wing structures as a weight reduction design feature. More significantly, the wings are outfitted with a novel control effector concept called variable camber continuous trailing edge (VCCTE) flap system for active control of wing aeroelastic deflections to optimize the local angle of attack of wing sections for improved aerodynamic efficiency through cruise drag reduction and lift enhancement during take-off and landing. The VCCTE flap is a multi-functional and aerodynamically efficient device capable of achieving high lift-to-drag ratios. The flap system is comprised of three chordwise segments that form the variable camber feature of the flap and multiple spanwise segments that form a piecewise continuous trailing edge. By configuring the flap camber and trailing edge shape, drag reduction could be achieved. Moreover, some parts of the flap system can be made to have a high frequency response for roll control, gust load alleviation, and aeroservoelastic (ASE) modal suppression control. Abstract The aeroelastic model of the ESAC is based on one-dimensional structural dynamic theory that captures the aeroelastic deformation of a wing structure in a combined motion that involves flapwise bending, chordwise bending, and torsion. The model includes the effect of aircraft propulsion due to wing flexibility which causes the propulsive forces and moments to couple with the wing elastic motion. Engine mass is also accounted in the model. A fuel management model is developed to describe the wing mass change due to fuel usage in the main tank and wing tanks during cruise. Abstract The model computes both static and dynamic responses of the wing structures. The static aeroelastic deflections are used to estimate the effect of wing flexibility on induced drag and the potential drag reduction by the VCCTE flap system. A flutter analysis is conducted to estimate the flutter speed boundary. Gust load alleviation via adaptive control has been recently investigated to address flexibility of aircraft structures. A multi-objective flight control approach is presented for drag reduction control. The approach is based on an optimal control framework using a multi-objective cost function. Future studies will demonstrate the potential benefits of the approach.

Aeroelasticity↗
NASA NTRS2022

Ruggedness Evaluation of ASTM International Standard Test Methods for Shape Memory Materials: E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys

This paper evaluates the ruggedness testing of the newly released ASTM International E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors of strain rate (ė), heating and cooling rates (Ṫ(heat) and Ṫ(cool), respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (thold), and minimum load (Fmin) imparted on the samples. The results indicate that the hold time factor had no effect on any result variable. The minimum load factor, alternatively, had the greatest effect on several result variables, with the greatest influence on the strains at martensite start and finish (strain variation ~0.1 percent), and the strains at the upper and lower cycle temperatures (strain variation of 0.14 percent). The UCT was found to have a large effect on the austenite and martensite finish tangent line and data intersect, denoted by Af* and Mf*, by ~17 and 4 °C, respectively. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test methods are presented.

shape memory alloy↗
NASA NTRS2023

Ruggedness Evaluation of ASTM International Standard Test Methods for Shape Memory Materials: E3098 Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys

This paper evaluates the ruggedness testing of the recently released ASTM International E3098 Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors: strain rate (ė), heating and cooling rates (Ṫ heat and Ṫ cool , respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (t hold ), and minimum load (F min ) imparted on the samples. The results indicate that the strain rate factor had no effect on any result variable, whereas the minimum load factor had a large effect on several result variables including the austenite start and martensite finish temperatures as well as most of the strain measurements from the thermal cycle. The lower cycle temperature factor had a large effect on the stress at maximum strain during pre-straining (e i ), denoted by S i , at ~7.2 MPa, as well as the A f , at 5.47 °C. Closely following the LCT effect, Ṫ heat was found to have a large effect on the austenite start temperature (A s ), at a value of ~2.72 °C. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test method are presented.

Shape memory alloys↗
NASA NTRS1980

An empirical model of the Venusian outer environment. I - The shape of the dayside solar wind-atmosphere interface. II - The shape and location of the bow shock

Solar wind plasma and magnetic field data and ionospheric data obtained from the Pioneer Venus orbiter are discussed. The variation in the magnetic field pressure within the magnetic barrier is shown to be similar to that expected for the solar wind pressure variations along an obstacle's boundary when a more realistic approximation of the shape of the ionosphere is included. Simultaneous solar wind pressure, ionospheric pressure, and magnetic barrier pressure data reveal that the ionospheric pressure below the ionopause is approximately equal to the solar wind pressure. The magnetic barrier pressure is found to be equal to approximately 2/3 to 3/4 of both the solar wind pressure and the ionospheric pressure. Estimates of the hot plasma pressure contribution to the total pressure in the magnetic barrier vary from 1/4 to 1/3. Just below the ionopause the ionospheric pressure deviations from the mean ionospheric pressure are significant, especially below approximately 400 km; they appear to be indicative of the adjustment of the ionospheric structure to changeing solar wind conditions. A first-order model of the ionopause pressure variations as a function of height and solar-zenith angle is proposed. Venera 9 and Venera 10 bow shock crossings are then analyzed for solar zenith angles in the range from approximately 25 deg to approximately 153 deg. A comparison of Venera 9 and Venera 10 bow shock crossings with those observed by the Pioneer Venus orbiter suggests that both the secular variation and the latitudinal asymmetry may be responsible for the closer shock crossings of the Venera 9 and Venera 10 spacecraft.

Vaisberg, O. L.↗
NASA NTRS2011

An Estimate of the Size and Shape of Sunspot Cycle 24 Based on its Early Cycle Behavior using the Hathaway-Wilson-Reichmann Shape-Fitting Function

On the basis of 12-month moving averages (12-mma) of monthly mean sunspot number (R), sunspot cycle 24 had its minimum amplitude (Rm = 1.7) in December 2008. At 12 mo past minimum, R measured 8.3, and at 18 mo past minimum, it measured 16.4. Thus far, the maximum month-to-month rate of rise in 12-mma values of monthly mean sunspot number (AR(t) max) has been 1.7, having occurred at elapsed times past minimum amplitude (t) of 14 and 15 mo. Compared to other sunspot cycles of the modern era, cycle 24?s Rm and AR(t) max (as observed so far) are the smallest on record, suggesting that it likely will be a slow-rising, long-period sunspot cycle of below average maximum amplitude (RM). Supporting this view is the now observed relative strength of cycle 24?s geomagnetic minimum amplitude as measured using the 12-mma value of the aa-geomagnetic index (aam = 8.4), which also is the smallest on record, having occurred at t equals 8 and 9 mo. From the method of Ohl (the inferred preferential association between RM and aam), one predicts RM = 55 +/- 17 (the ?1 se prediction interval) for cycle 24. Furthermore, from the Waldmeier effect (the inferred preferential association between the ascent duration (ASC) and RM) one predicts an ASC longer than 48 mo for cycle 24; hence, maximum amplitude occurrence should be after December 2012. Application of the Hathaway-Wilson-Reichmann shape-fitting function, using an RM = 70 and ASC = 56 mo, is found to adequately fit the early sunspot number growth of cycle 24.

Wilson, Robert M.↗