Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shear failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

What is (and Isn't) Wrong with Both the Tension and Shear Failure Models for the Formation of Lineae on Europa

An unresolved problem in the interpretation of lineae on Europa is whether they formed as tension- or shear-fractures. Voyager image analyses led to hypotheses that Europan lineaments are tension cracks induced by tidal deformation of the ice crust. This interpretation continued with Galileo image analyses, with lineae being classified as crust- penetrating tension cracks. Tension fracturing has also been an implicit assumption of nonsynchronous rotation (NSR) studies. However, recent hypotheses invoke shear failure to explain lineae development. If a shear failure mechanism is correct, it will be necessary to re-evaluate any models for the evolution of Europa's crust that are based on tensile failure models, such as NSR estimates. For this reason, it is imperative that the mechanism by which fractures are initiated on Europa be unambiguously unraveled. A logical starting point is an evaluation of the pros and cons of each failure model, highlighting the lines of evidence that are needed to fully justify either model.

Kattenhorn, S. A.↗
NASA NTRS1989

An analysis of shear failure mechanisms for compression-loaded (+/-theta)s laminates

An analysis of interlaminar and in-plane shear failures for (+/-theta)s composite laminates loaded in uniaxial compression is described. A laminate model is presented that idealizes each ply as a plate supported by an elastic foundation. A nonlinear analysis for plies with short-wavelength initial imperfections is used to determine laminate stresses and interlaminar strains. A failure criterion that uses the results of the nonlinear analysis is introduced.

Shuart, Mark J.↗
NASA NTRS1985

Short-wavelength buckling and shear failures for compression-loaded composite laminates

The short-wavelength buckling (or the microbuckling) and the interlaminar and inplane shear failures of multi-directional composite laminates loaded in uniaxial compression are investigated. A laminate model is presented that idealizes each lamina. The fibers in the lamina are modeled as a plate, and the matrix in the lamina is modeled as an elastic foundation. The out-of-plane w displacement for each plate is expressed as a trigonometric series in the half-wavelength of the mode shape for laminate short-wavelength buckling. Nonlinear strain-displacement relations are used. The model is applied to symmetric laminates having linear material behavior. The laminates are loaded in uniform end shortening and are simply supported. A linear analysis is used to determine the laminate stress, strain, and mode shape when short-wavelength buckling occurs. The equations for the laminate compressive stress at short-wavelength buckling are dominated by matrix contributions.

Shuart, M. J.↗
NASA NTRS1992

Seismicity, shear failure and modes of deformation in deep subduction zones

The joint hypocentral determination method is used to relocate deep seismicity reported in the International Seismological Center catalog for earthquakes deeper than 400 km in the Honshu, Bonin, Mariannas, Java, Banda, and South America subduction zones. Each deep seismic zone is found to display planar features of seismicity parallel to the Harvard centroid-moment tensor nodal planes, which are identified as planes of shear failure. The sense of displacement on these planes is one of resistance to deeper penetration.

Lundgren, Paul R.↗
DOE OSTI2024

Utah FORGE: Direct Shear Test Data for Investigating Seismic Precursors to Shear Failure of Fractures

This dataset includes results of direct shear tests to investigate the mechanical and geophysical response of dry and saturated fractures in Indiana limestone and Sierra White granite. Direct shear tests were performed on tensile-induced fractures in Indiana limestone and Sierra White granite in a custom water-pressurized chamber. The provided Excel files include the representative seismic wave signals and the normalized wave amplitudes of ultrasonic wave transducers. A link to the published journal article presenting the data and describing the experiment in detail is provided as well.

15 GEOTHERMAL ENERGY↗
NASA NTRS1992

Shear failure and impact resistance in graphite fiber laminates

The multispan beam (MSB) test was evaluated as a predictor of damage resistance and damage tolerance in quasi-isotropic graphite laminates. Materials studied were five commercial prepreg system using high-strain and intermediate-modulus carbon fibers, as well as an amorphous thermoplastic system. Failure loads and displacements in the MSB tests showed little rate dependence. Values of compressive strength after a standard low-velocity impact correlated fairly well with the MSB results.

Srinivasan, Krishna↗
NASA NTRS1985

Longitudinal splitting in unidirectional composites, analysis and experiments

An experimental study is conducted to determine the fracture behavior of center notched, unidirectional graphite/epoxy laminates when subjected to tensile loading. The actual behavior is compared to the behavior predicted by a mathematical model based on classical shear-lag assumptions. The model allows for damage to occur in the form of longitudinal matrix yielding and splitting with the matrix assumed to fail in pure shear. Results indicate that the model is capable of predicting split initiation stress levels accurately, but does not describe the subsequent split growth adequately. The model predicts rapid split growth following split initiation due to shear failure, while the actual behavior involves a slow split growth region prior to the rapid growth region. It is suggested that transverse matrix normal stresses are responsible for split initiation and the early, slow split growth. The model predicts the actual initiation stress levels reliably, and also appears to be able to predict the point at which the shear failure mode begins to dominate. The shear failure mode does eventually dominate, but at a slower rate than predicted. The nonuniform structure of the graphite/epoxy laminates is thought to be responsible for decreasing the split growth rate due to shear failure.

Goree, J. G.↗
NASA NTRS1992

Mechanism of slip and twinning

The objectives are to: (1) demonstrate the mechanisms of deformation in body centered cubic (BCC), face centered cubic (FCC), and hexagonal close-packed (HCP)-structure metals and alloys and in some ceramics as well; (2) examine the deformed microstructures (slip lines and twin boundaries) in different grains of metallic and ceramic specimens; and (3) study visually the deformed macrostructure (slip and twin bands) of metals and alloys. Some of the topics covered include: deformation behavior of materials, mechanisms of plastic deformation, slip bands, twin bands, ductile failure, intergranular fracture, shear failure, slip planes, crystal deformation, and dislocations in ceramics.

Rastani, Mansur↗
NASA NTRS1994

Post-impact fatigue of cross-plied, through-the-thickness reinforced carbon/epoxy composites

An experimental investigation of the post-impact fatigue response of integrally woven carbon/epoxy composites was conducted. Five different through-the-thickness (TTT) reinforcing fibers were used in an experimental textile process that produced an integrally woven (0/90/0/90/0/90/0/90/0)(sub T) ply layup with 21K AS4 carbon tow fiber. The resin was Hercules 3501-6, and the five TTT reinforcing fibers were Kevlar, Toray carbon, AS4 carbon, glass, and IM6 carbon. The purpose of this investigation was to study the post-impact fatigue response of these material systems and to identify the optimum TTT fiber. Samples were impacted with one half inch diameter aluminum balls with an average velocity of 543 ft/sec. Post-impact static compression and constant amplitude tension-compression fatigue tests were conducted. Fatigue tests were conducted with a loading ratio of R=-5, and frequency of 4 Hz. Damage growth was monitored using x-radiographic and sectioning techniques and by examining the stress-strain response (across the impact site) throughout the fatigue tests. The static compressive stress versus far-field strain response was nearly linear for all material groups. All the samples had a transverse shear failure mode. The average compressive modulus (from far-field strain) was about 10 Msi. The average post-impact static compressive strength was about 35.5 Ksi. The IM6 carbon sample had a strength of over 40 Ksi, more than 16 percent stronger than average. There was considerable scatter in the S-N data. However, the IM6 carbon samples clearly had the best fatigue response. The response of the other materials, while worse than IM6 carbon, could not be ranked definitively. The initial damage zones caused by the impact loading and damage growth from fatigue loading were similar for all five TTT reinforcing materials. The initial damage zones were circular and consisted of delaminations, matrix cracks and ply cracks. Post-impact fatigue loading caused delamination growth, ply cracking and fiber bundle failures, typically 45 deg from impact load direction. During the initial 97 percent of fatigue life, delaminations, ply cracks and fiber bundle failures primarily grew at and near the impact site. During the final 3 percent of life, damage grew rapidly transverse to the loading direction as a through-the-thickness transverse shear failure. The stress-strain response was typically linear during the initial 50 percent of life, and stiffness dropped about 20 percent during this period. During the next 47 percent of life, stiffness dropped about 34 percent, and the stress-strain response was no longer linear. The stiffness decreased about 23 percent during the final 3 percent of life. These trends were typical of all the materials tested. Therefore, by monitoring stiffness loss, fatigue failure could be accurately anticipated.

Serdinak, Thomas E.↗
NASA NTRS1992

Postbuckling failure of composite plates with central holes

The postbuckling failure of square composite plates with central holes is analyzed numerically and experimentally. The particular plates studies have stacking sequences of: (+ and - 45/0/90)(sub 2S); (+ and - 45/0(sub 2))(sub 2S); (+ and - 45/0(sub 6))(sub S); and (+ and - 45)(sub 4S). A simple plate geometry, one with a hole diameter to plate width ratio of 0.3 is compared. Failure load, failure mode, and failure location are predicted numerically by using the finite element method. Predictions are compared with experimental results. In numerical failure analysis the interlaminar shear stresses, as well as the inplane stresses are taken into account. An issue addressed in this study is the possible mode shape change of the plate during loading. It is predicted that the first three laminates fail due to excessive stresses in the fiber direction, and more importantly, that the load level is independent of whether the laminate is deformed in a one-half or two-half wave configuration. It is predicted that the fourth laminate fails due to excessive inplane shear stress. Interlaminar shear failure is not predicted for any laminates. For the first two laminates the experimental observations correlated well with the predictions. Experimentally, the third laminate failed along the side support due to interlaminar shear strength S(sub 23). The fourth experimental laminate failed due to inplane shear in the location predicted, however material softening resulted in a different failure load from predictions.

Lee, H. H.↗
DOE OSTI2024

Physics informed neural network can retrieve rate and state friction parameters from acoustic monitoring of laboratory stick-slip experiments

Various machine learning (ML) and deep learning (DL) techniques have been recently applied to the forecasting of laboratory earthquakes from friction experiments. The magnitude and timing of shear failures in stick-slip cycles are predicted using features extracted from the recorded ultrasonic or acoustic emission (AE) signals. In addition, the Rate and State Friction (RSF) constitutive laws are extensively used to model the frictional behavior of faults. In this work, we use data from shear experiments coupled with passive acoustic (variance, kurtosis, and AE rate) interleaved with active source ultrasonic monitoring (transmitted wave amplitude) to develop physics-informed neural network (PINN) models incorporating the RSF law and AE rate generation equation with wave amplitude serving as a proxy for friction state variable. This PINN framework allows learning RSF parameters from stick-slip experiments rather than measuring them through a series of velocity step experiments. We observe that when the stick-slip cycles are irregular, the PINN models outperform the data-driven DL models. Transfer learning (TL) PINN models are also developed by pre-training on data collected at one normal stress level followed by forecasting shear failures and retrieving RSF parameters at other stress levels (i.e., with different recurrence intervals) after retraining on a limited amount of new data. Our findings suggest that TL models perform better compared to standalone models. Both standalone and TL PINN-estimated RSF parameters and their ground truth values show excellent agreements thus demonstrating that RSF parameters can be retrieved from laboratory stick-slip experiments using the corresponding acoustic data and that the transmitted wave amplitude provides a good representation of the evolving frictional state during stick-slips.

58 GEOSCIENCES↗
NASA NTRS1985

A compressive failure model for anisotropic plates with a cutout under compressive and shear loads

Failure models for the prediction of compressive strength of plates with a hole are investigated. One of the models is based on the strength failure of the fibers that leads to fiber kinking failure. A different version is developed for cases where shear failure of the fibers is expected to be a dominate failure mode. Both models are capable of including the effects of combined shearing and compressive stresses around a hole in a plate and, therefore, are expected to be applicable to plates under combined shearing and compressive loadings, as well as anisotropic plates.

Guerdal, Zafer↗
DOE OSTI2026

Laser interference structuring of Cu for adhesive joining of HVAC equipment

Due to potential energy and cost savings benefits, adhesive joining has been recently considered for heating, ventilation, air conditioning, and refrigeration (HVAC&R) systems. HVAC adhesive bonding requires cost-effective and adequate surface preparations of adherents. Here, this article investigates the use of abrasion, traditional single-beam laser, and a laser-interference technique as surface preparations of copper surfaces. Surface morphology is characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Effective submicrometer peak-to-valley structuring with a periodicity of ∼2.7μ⁢m was demonstrated for laser-interference processing. Single-lap shear tests were conducted for 89 joints made with bondline thicknesses of 0.15 and 0.3 mm. Data on process variables and measured variables included open-time, bond length, maximum load, displacement at failure, shear lap strength, and failure mode. A statistical analysis was conducted on each lot to determine the lower limit with 95% confidence intervals for displacements at failure and shear lap strengths. A comparison is presented between the properties of laser-structured joints with respect to those prepared by abrasion, which is considered the baseline surface preparation technique. Based on this comparison, one single-beam laser technique and two laser-interference techniques were shown to exhibit vastly superior performance over the joints made with abraded specimens.

Sabau, Adrian S. [Oak Ridge National Laboratory (O↗
NASA NTRS1971

New primers for adhesive bonding of aluminum alloys

Synthetic polypeptide adhesive primers are effective, with high temperature epoxy resins, at temperatures from 100 deg to 300 deg C. Lap-shear failure loads and lap-shear strength of both primers are discussed.

Burrell, B. W.↗
NASA NTRS1984

Application of Iosipescu specimen geometry to determination of shear strength in unidirectional composites

The Iosipescu (1967) test method, in conjunction with a finite element analysis of anisotropic, unidirectionally reinforced composite specimens, can be used to derive composite shear strength values despite the small size of the samples used. When such a specimen is loaded parallel to the fiber direction, fracture occurs by shear within a narrow region near the center of the specimen; this is consistent with the maximum shear area determined by finite element analysis. The resulting fracture surface, as observed, is characteristic of shear failure, occurring either within the matrix or at the fiber-matrix interface. Problems of compressive and mixed mode failure which accrue to short beam shear specimens are by the present method precluded.

Hurwitz, F. I.↗
DOE OSTI2024

A high-resolution pseudo-polygon discrete element model for regional sea ice

Here, this work presents a pseudo-polygon discrete element model for high-resolution sea ice simulations. A scale-invariant bonded particle contact model is proposed to model joints between sea ice floes based on the smeared fracture model and a lattice spring beam model, and the Mohr–Coulomb failure criterion is implemented to represent the shearing failure mechanism of sea ice packings under complex loadings. All mechanical parameters of the bond model can be directly determined from laboratory tests. Validations of the proposed model are made by investigations of mechanical response and failure criteria of field sea ice sheets. Compared with the field observations of sea ice from satellite radar and in situ stress sensors, the proposed model is capable of reproducing the typical constitutive behavior and the Coulomb friction envelope of field sea ice. Finally, the proposed discrete element sea ice model is used to study the effect of loading rates on mechanical behavior including failure strength of regional sea ice.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1991

Micromechanics of fatigue in woven and stitched composites

The goal is to determine how microstructural factors, especially the architecture of microstructural factors, control fatigue damage in 3D reinforced polymer composites. Test materials were fabricated from various preforms, including stitched quasi-isotropic laminates, and through-the-thickness angle interlock, layer-to-layer angle interlock, and through-the-thickness stitching effect weaves. Preforms were impregnated with a tough resin by a special vacuum infiltration method. Most tests are being performed in uniaxial compression/compression loading. In all cases to date, failure has occurred not by delamination, but by shear failure, which occurs suddenly rather than by gradual macroscopic crack growth. Some theoretical aspects of bridging are also examined.

Cox, B. N.↗