Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shell effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Toward Effective Shell Modeling of Wrinkled Thin-Film Membranes Exhibiting Stress Concentrations

Geometrically nonlinear shell finite element analysis has recently been applied to solar-sail membrane problems in order to model the out-of-plane deformations due to structural wrinkling. Whereas certain problems lend themselves to achieving converged nonlinear solutions that compare favorably with experimental observations, solutions to tensioned membranes exhibiting high stress concentrations have been difficult to obtain even with the best nonlinear finite element codes and advanced shell element technology. In this paper, two numerical studies are presented that pave the way to improving the modeling of this class of nonlinear problems. The studies address the issues of mesh refinement and stress-concentration alleviation, and the effects of these modeling strategies on the ability to attain converged nonlinear deformations due to wrinkling. The numerical studies demonstrate that excessive mesh refinement in the regions of stress concentration may be disadvantageous to achieving wrinkled equilibrium states, causing the nonlinear solution to lock in the membrane response mode, while totally discarding the very low-energy bending response that is necessary to cause wrinkling deformation patterns. An element-level, strain-energy density criterion is suggested for facilitating automated, adaptive mesh refinements specifically aimed at the modeling of thin-film membranes undergoing wrinkling deformations.

Tessler, Alexander↗
NASA NTRS1983

Laser-modified electron scattering from a slowly ionising atom

When an electron scatters from an atom in the presence of a laser field which is resonant with an atomic transition, off-shell effects enter into the cross section. These only become significant at higher laser intensities where the atom may also be ionised by the laser. Cross-sections are obtained for electron-atom scattering in which these off-shell effects appear and in which the slow ionisation of the atom by the laser is included. Experiments are suggested in which simplifications can occur and which still retain these 'exotic' effects.

Fiordilino, E.↗
NASA NTRS1991

Lessons learned in the development of the STOL intelligent tutoring system

Lessons learned during the development of the NASA Systems Test and Operations Language (STOL) Intelligent Tutoring System (ITS), being developed at NASA Goddard Space Flight Center are presented. The purpose of the intelligent tutor is to train STOL users by adapting tutoring based on inferred student strengths and weaknesses. This system has been under development for over one year and numerous lessons learned have emerged. These observations are presented in three sections, as follows. The first section addresses the methodology employed in the development of the STOL ITS and briefly presents the ITS architecture. The second presents lessons learned, in the areas of: intelligent tutor development; documentation and reporting; cost and schedule control; and tools and shells effectiveness. The third section presents recommendations which may be considered by other ITS developers, addressing: access, use and selection of subject matter experts; steps involved in ITS development; use of ITS interface design prototypes as part of knowledge engineering; and tools and shells effectiveness.

Seamster, Thomas↗
NASA NTRS2024

Test and Analysis of the 8-foot Diameter Cylindrical Sandwich Composite Test Article CTA8.2B: As part of the NASA Engineering and Safety Center Shell Buckling Knockdown Factor Project

The buckling response of thin-walled cylindrical structures have long been shown to be sensitive to various imperfections. That is, imperfections related to load introduction, boundary conditions, material property variation, and geometric deviations can all contribute to experimentally obtained buckling loads being lower than the buckling loads predicted for perfect representations of the same thin-walled cylindrical structure. To account for the influence of geometry-based imperfections of a thin-walled cylindrical structure on buckling response, a design factor (also known as a buckling knockdown factor) is used during the design phase. Guidelines for buckling knockdown factors are readily available in NASA SP-8007, Buckling of Thin Walled Circular Cylinders, which was updated in 2020. Prior to this recent update, NASA SP-8007 had not been updated since 1969, and since that time, computational analysis, experimental testing, and manufacturing methods have significantly improved. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF, NESC Assessment 07-010-E) had the goal of developing buckling design recommendations for select classes of metallic and composite launch-vehicle structures [3]. Specifically, the test and analysis results from the fourth SBKF composite test article SBKF-P3-CYL-CTA8.2B, which is referred to as CTA8.2B, are described in this paper. This test was the fourth in a series of four tests on sandwich composite cylinders that will be used to experimentally validate analysis methods, which in turn can be used to develop new analysis-based shell buckling design guidelines for typical sandwich composite launch vehicle cylindrical structures. Publications describing previous test validation with analysis are available in Refs. CTA8.2B was designed to occupy one corner of the design space with approximately equal bending stiffnesses in the axial and transverse directions and have a larger ratio of radius to effective shell thickness. Each test article had a unique design and was designed to occupy a specific region of the design space. CTA8.2B was an 8-foot diameter honeycomb-core sandwich cylinder that was fabricated and tested at the NASA Marshall Space Flight Center (MSFC). The primary objectives of this test were to interrogate the structural capability of a composite test article, and to verify the test article design and analysis approach for cylinders subjected to axial compression and combined axial and bending loads. First, descriptions of the test article design and test are given in Section 2.0, and modeling and analysis methods used in support of the test article design and testing activities are described briefly in Section 3.0. Then, select test results are presented and compared to predicted results in Section 4.0, and concluding remarks are presented in Section 5.0. Finally, drawings of CTA8.2B and references used to support the test and analysis are provided in the Appendix.

Nonlinear analysis↗
NASA NTRS2010

Effects of Buckling Knockdown Factor, Internal Pressure and Material on the Design of Stiffened Cylinders

A design study was conducted to investigate the effect shell buckling knockdown factor (SBKF), internal pressure and aluminum alloy material selection on the structural weight of stiffened cylindrical shells. Two structural optimization codes were used for the design study to determine the optimum minimum-weight design for a series of design cases, and included an in-house developed genetic algorithm (GA) code and PANDA2. Each design case specified a unique set of geometry, material, knockdown factor combinations and loads. The resulting designs were examined and compared to determine the effects of SBKF, internal pressure and material selection on the acreage design weight and controlling failure mode. This design study shows that use of less conservative SBKF values, including internal pressure, and proper selection of material alloy can result in significant weight savings for stiffened cylinders. In particular, buckling-critical cylinders with integrally machined stiffener construction can benefit from the use of thicker plate material that enables taller stiffeners, even when the stiffness, strength and density properties of these materials appear to be inferior.

Lovejoy, Andrew E.↗
NASA NTRS1990

Charge exchange of low-energy ions in thin carbon foils

In order to calibrate a time-of-flight mass spectrometer which is to be flown in the solar wind, the charge exchange properties of low-energy ions in thin carbon foils have been investigated. Incident ions of He, C, N, O, Ne, and Ar with energies in the range 0.5-2 keV/nucleon have been used to measure charge-state distribution, residual energy, and angular distribution after transmission through thin (1-6 microgram/sq cm) carbon foils. Within such foils, an equilibrium between ionization and recombination of the projectile is rapidly established, and, consequently, the charge state of the emerging particle depends essentially on its residual velocity. A comparison of the charge exchange properties of Ne-22 with Ne-20 demonstrates that indeed the velocity (and not the energy) of the emerging particle determines its final charge. A comparison of properties of different elements provides an indication of an electron shell effect. Predictions for the energy loss of ions within the carbon foils made with the TRIM code are in good agreement with the experimental results presented in this paper.

Buergi, Alfred↗
NASA NTRSDate not supplied

Multiscale Simulation of Deployable Composite Structures

In this paper, a multiscale simulation method for analyzing deployable composite structures is presented. Effective shell properties of the composites are obtained based on Mechanics of Structure Genome (MSG) homogenization, and then implemented into a user-subroutine UGENS for structural simulation with shell elements in Abaqus. The column bending test(CBT) of a flat thin flexure and lenticular composite boom in a simplified deployer structure are studied for demonstration. A viscoelastic material model with direct integration is adopted in this paper. The CBT simulation shows good agreement with experiments during relaxation, while errors are observed when comparing residual deformation. It is shown that this CBT model can be calibrated to CBT test results. For the lenticular boom analysis, the complete process of flattening, coiling, stowage, deployment and recovery is simulated with the viscoelastic shell model.

Finite element analysis↗