Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sideband”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Experimental study of the influence of wind on Benjamin-Feir sideband instability

A laboratory investigation of the influence of wind on the evolution of mechanically generated regular (m.g.r.) waves is reported. Surface elevation measurements were made at four fetches for steep (0.1 less than ak(bar) less than 0.2, 2 Hz) m.g.r. waves, moderate (15 less than u(asterisk) less than 25 cm/s, 3-6 Hz) wind waves, and combinations of the m.g.r. and wind waves. The m.g.r. wave spectra exhibit Benjamin-Feir sidebands that grow exponentially with fetch and whose growth rate increases as the initial wave steepness increases. As fetch increases for the wind cases, total energy increases and the frequency of the spectral maximum downshifts, but no spectral lines representing Benjamin-Feir sidebands were detected even though the wave steepness and fetch were similar to the m.g.r. waves whose spectra displayed sidebands. As wind speed increased over the m.g.r. waves, sideband magnitude, sideband growth rate, and low-frequency perturbation components associated with the instability mechanism were reduced.

Bliven, L. F.↗
NASA NTRS1989

HF sideband generation in the ionosphere

The temporal development of sidebands excited near sunrise by two strong HF waves separated by a few hertz is presented. Sidebands are not observed before sunrise when the ionospheric critical frequency is less than the heater frequency. As the ionospheric density increases following sunrise and overdense conditions are established, strong sidebands emerge. Even though these results favor a mechanism which phase modulates the reflected HF wave over one which first downconverts the HF power to ULF before exciting sidebands, it is possible that either mechanism could at times contribute to sideband production.

Noble, S. T.↗
DOE OSTI2026

Fast Sideband Control of a Multimode Cavity Memory with Weak Dispersive Coupling to a Transmon

Mitigating ancilla-mediated error channels is a critical challenge in controlling high-quality superconducting cavities using circuit quantum electrodynamics (cQED). We address this by weakening the dispersive coupling while demonstrating fast, high-fidelity multimode control through transmon-mediated sideband interactions. We implement transmon-cavity SWAP gates with speeds up to 30 times larger than the bare dispersive coupling. Combined with transmon rotations, this enables universal state preparation in a single mode, though achieving unitary gates and extending control to multiple modes remains a challenge. In this work, we overcome this limitation by introducing two control strategies: (i) a shelving technique that stores populations in sideband-transparent states, and (ii) a method that exploits the dispersive shift to implement photon-number-selective transmon-cavity SWAP gates. We use these protocols to prepare Fock and binomial code states across any of the ten modes of a multimode cavity with millisecond coherence times—serving as a multimode quantum memory. We demonstrate unitaries that encode and decode an arbitrary qubit state from the transmon into corresponding vacuum and Fock state superpositions, as well as entangled NOON states of cavity mode pairs—a scheme extendable to arbitrary multimode Fock encodings in the cavity modes. Furthermore, we implement a new binomial encoding gate that converts arbitrary transmon superpositions into binomial code states in any cavity mode at a rate exceeding the dispersive shifts in our system, achieving an average post-selected state fidelity of 96.3% in a 4 μ⁢s gate time. By using precalibrated transmon and sideband pulses, our work demonstrates multimode control with significantly reduced calibration overhead, enabling efficient unitary operations using sideband interactions in multimode cQED systems.

Huang, Jordan [Rutgers Univ., Piscataway, NJ (Unit↗
DOE OSTI2025

Fast Sideband Control of a Weakly Coupled Multimode Bosonic Memory

Circuit quantum electrodynamics (cQED) with superconducting cavities coupled to nonlinear circuits like transmons offers a promising platform for hardware-efficient quantum information processing. We address critical challenges in realizing this architecture by weakening the dispersive coupling while also demonstrating fast, high-fidelity multimode control by dynamically amplifying gate speeds through transmon-mediated sideband interactions. This approach enables transmon-cavity SWAP gates, for which we achieve speeds up to 30 times larger than the bare dispersive coupling. Combined with transmon rotations, this allows for efficient, universal state preparation in a single cavity mode, though achieving unitary gates and extending control to multiple modes remains a challenge. In this work, we overcome this by introducing two sideband control strategies: (1) a shelving technique that prevents unwanted transitions by temporarily storing populations in sideband-transparent transmon states and (2) a method that exploits the dispersive shift to synchronize sideband transition rates across chosen photon-number pairs to implement transmon-cavity SWAP gates that are selective on photon number. We leverage these protocols to prepare Fock and binomial code states across any of ten modes of a multimode cavity with millisecond cavity coherence times. We demonstrate the encoding of a qubit from a transmon into arbitrary vacuum and Fock state superpositions, as well as entangled NOON states of cavity mode pairs— a scheme extendable to arbitrary multimode Fock encodings. Furthermore, we implement a new binomial encoding gate that converts arbitrary transmon superpositions into binomial code states in $\qty{4}{\micro\second}$ (less than $1/\chi$), achieving an average post-selected final state fidelity of $\qty{96.3}{\percent}$ across different fiducial input states.

Huang, Jordan [Rutgers U., Piscataway]↗
DOE OSTI2024

Tunable UV ∼ IR frequency comb generation via high-order sideband generation

Abstract We propose the generation of a widely tunable UV-to-IR frequency comb by high-order sideband generation (HSB) spectrum emitted from semiconductors. In our theoretical simulations, we demonstrate the high-order sideband signals of two series (2m Ω seed + (2n + 1) ω driver , and (2m + 1) Ω seed + 2 n ω driver ), wheremandnare integers of a seed pulse and a driver laser frequency, respectively. The simulations also reveal the intensity of HSB scale with the driver laser power, both perturbatively and non-perturbatively. We find that the harmonic position and spacing of the high-order sideband emission can be controlled by varying the seed pulse and driver photon energies. In the experiment, we applied a visible ( ℏ Ω seed = 3.1 eV, ∼400 nm) seed pulse and mid-infrared (MIR, ℏ ω driver = 0.4 eV, 3.1 μm) driver pulses to ZnSe target. Our experimental observations confirmed the UV (4.7 eV, 263 nm and 3.9 eV, 317 nm) HSB generation.

Physics↗
NASA NTRS1972

Binary single-sideband phase-modulated communication systems.

Single-sideband phase modulation (SSBPM), in which a signal is simultaneously phase- and amplitude-modulated by a signal and its Hilbert transform, is shown to be suboptimum for binary signaling in white Gaussian noise. An alternative single-sideband technique based on the properties of binary suppressed-carrier phase modulation is proposed and shown to give performance equivalent to the double-sideband version.

Chadwick, H. D.↗
NASA NTRS1982

Sideband-aided receiver arraying

Efforts to increase the amount of data that can be received from outer planet missions by coherently combining signals from ground antennas in such a way as to increase the total effective aperture of the receiving system are discussed. As these signals become weaker, the baseband arraying technique in current use degrades somewhat due to carrier jitter. One solution to this problem is Sideband-Aided Receiver Arraying (SARA). In SARA, sidebands demodulated to baseband in a master receiver at the largest antenna are used to allow slave receivers in the other antennas to track the sideband power in the signal rather than the carrier power. The already existing receivers can be used in the slaves to track and demodulate the signals in either a residual carrier or a suppressed carrier environment. The resultant baseband signals from all the antennas can then be combined using existing baseband combining equiment. Computer simulations of SARA show increases in throughput (measured in data bits per second) over baseband-only combining 17 percent at Voyager 2 Uranum encounter and 31 percent at Neptune for a four-element antenna array and (7, 1/2) convolutional coding.

Butman, S. A.↗
NASA NTRS1999

177-207 GHz Radiometer Front End: Single Sideband Measurements

Twenty years of progress in 200 GHz receivers for spaceborne remote sensing has yielded a 180-220 GHz technology with maturing characteristics, as evident by increasing availability of relevant hardware, paralleled by further refinement in receiver performance requirements at this spectrum band. The 177-207 GHz superheterodyne receiver, for the Earth observing system (EOS) microwave limb sounder (MLS), effectively illustrates such technology developments. This MLS receiver simultaneously detects six different signals, located at sidebands below and above its 191.95 GHZ local-oscillator (LO). The paper describes the MLS 177-207 GHz receiver front-end (RFE), and provides measured data for its lower and upper sidebands. Sideband ratio data is provided as a function of IF frequency, at different LO power drive, and for variation in the ambient temperature.

Galin, I.↗
NASA NTRS2003

Methods and devices based on brillouin selective sideband amplification

Opto-electronic devices and techniques using Brillouin scattering to select a sideband in a modulated optical carrier signal for amplification. Two lasers respectively provide a carrier signal beam and a Brillouin pump beam which are fed into an Brillouin optical medium in opposite directions. The relative frequency separation between the lasers is adjusted to align the frequency of the backscattered Brillouin signal with a desired sideband in the carrier signal to effect a Brillouin gain on the sideband. This effect can be used to implement photonic RF signal mixing and conversion with gain, conversion from phase modulation to amplitude modulation, photonic RF frequency multiplication, optical and RF pulse generation and manipulation, and frequency-locking of lasers.

Yao, X. Steve↗
NASA NTRS2010

Optical Sidebands Multiplier

Optical sidebands have been generated with relative frequency tens to hundreds of GHz by using optical sidebands that are generated in a cascade process in high-quality optical resonators with Kerr nonlinearity, such as whispering gallery mode (WGM) resonators. For this purpose, the WGM resonator needs to be optically pumped at two frequencies matching its resonances. These two optical components can be one or several free spectral ranges (FSRs), equal to approximately 12 GHz, in this example, apart from each other, and can be easily derived from a monochromatic pump with an ordinary EOM (electro-optic modulation) operating at half the FSR frequency. With sufficient nonlinearity, an optical cascade process will convert the two pump frequencies into a comb-like structure extending many FSRs around the carrier frequency. This has a demonstratively efficient frequency conversion of this type with only a few milliwatt optical pump power. The concept of using Kerr nonlinearity in a resonator for non-degenerate wave mixing has been discussed before, but it was a common belief that this was a weak process requiring very high peak powers to be observable. It was not thought possible for this approach to compete with electro-optical modulators in CW applications, especially those at lower optical powers. By using the high-Q WGM resonators, the effective Kerr nonlinearity can be made so high that, using even weak seeding bands available from a conventional EOM, one can effectively multiply the optical sidebands, extending them into an otherwise inaccessible frequency range.

Strekalov, Dmitry V.↗
DOE OSTI2024

High-performance silicon photonic single-sideband modulators for cold-atom interferometry

The laser system is the most complex component of a light-pulse atom interferometer (LPAI), controlling frequencies and intensities of multiple laser beams to configure quantum gravity and inertial sensors. Its main functions include cold-atom generation, state preparation, state-selective detection, and generating a coherent two-photon process for the light-pulse sequence. To achieve substantial miniaturization and ruggedization, we integrate key laser system functions onto a photonic integrated circuit. Our study focuses on a high-performance silicon photonic suppressed-carrier single-sideband (SC-SSB) modulator at 1560 nanometers, capable of dynamic frequency shifting within the LPAI. By independently controlling radio frequency (RF) channels, we achieve 30-decibel carrier suppression and unprecedented 47.8-decibel sideband suppression at peak conversion efficiency of –6.846 decibels (20.7%). We investigate imbalances in both amplitudes and phases between the RF signals. Using this modulator, we demonstrate cold-atom generation, state-selective detection, and atom interferometer fringes to estimate gravitational acceleration, g ≈ 9.77 ± 0.01 meters per second squared, in a rubidium ( 87 Rb) atom system.

47 OTHER INSTRUMENTATION↗
NASA NTRS1985

High-amplitude VLF transmitter signals and associated sidebands observed near the magnetic equatorial plane on the ISEE 1 satellite

New high-altitude ISEE 1 satellite observations of high-amplitude nonducted signals from the Omega navigation transmitter in North Dakota are reported. The amplitude of the signal was approximately 16-26 dB higher than that of similar signals observed at comparable locations on other days. Over the range L = 3.3-3.7, the transmitter pulses at 13.1 and 13.6 kHz were associated with sideband signals spaced in frequency roughly symmetrically about the carrier and generally reduced in amplitude by about 5 dB with respect to the carrier. The strongest sidebands were generally offset in frequency from the carrier by about + or - 55 Hz. Reasons are discussed for believing that the unusually high amplitude of the signals was due to wave amplification through the whistler-mode instability.

Bell, T. F.↗
NASA NTRS1987

Method and means for generation of tunable laser sidebands in the far-infrared region

A method for generating tunable far-infrared radiation is described. The apparatus includes a Schottky-barrier diode which has one side coupled through a conductor to a waveguide that carries a tunable microwave frequency; the diode has an opposite side which is coupled through a radiating whisker to a bias source. Infrared light is directed at the diode, and infrared light with tunable sidebands is radiated by the whisker through an open space to a reflector. The original infrared is separated from a tunable infrared sideband by a polarizing Michelson interferometer.

Pickett, Herbert M.↗
NASA NTRS1990

A Tone-Aided/Dual Vestigial Sideband (TA/DVSB) system for mobile satellite channels

Tone-aided modulation is one way of combatting the effects of multipath fading and Doppler frequency shifts. A new tone-aided modulation format for M-ary phase-shift keyed signals (MPSK) is discussed. A spectral null for the placement of the tone is created in the center of the MPSK signal by translating the upper sideband upwards in frequency by the same amount. The key element of the system is the algorithm for recombining the data sidebands in the receiver, a function that is performed by a specialized phase-locked loop (PLL). The system structure is discussed and simulation results showing the PLL acquisition performance are presented.

Saulnier, Gary J.↗
NASA NTRS1992

Measurements of the single sideband suppression for a 650 GHz heterodyne receiver

A large number of atmospheric trace gases, involved in the process of stratospheric ozone depletion, show emission features in the submillimeter wavelength range (lambda = 0.1-1mm). High-resolution heterodyne techniques are a particularly useful tool in this spectral region as vertical distribution of these species can be deduced. Here the receiver has to be operated in the single sideband (ssb) mode preferably to avoid any interferences between the contributions in both receiver sidebands. In the 625-655 GHz heterodyne receiver developed at the University of Bremen a Martin-Puplett interferometer is used as a ssb-filter. A laboratory set-up has been built up to measure the performance of this interferometer.

Crewell, S.↗
NASA NTRS2008

Frequency-Tuneable Pre-Stabilized Lasers for LISA via Sideband Locking

Laser frequency noise mitigation is one of the most challenging aspects of the LISA interferometric measurement system. The unstabilized frequency fluctuations must be suppressed by roughly twelve orders of magnitude in order to achieve a stability sufficient for gravitational wave detection. This enormous suppression will be achieved through a combination of stabilization and common-mode rejection. The stabilization component will itself be achieved in two stages: pre-stabilization to a local optical cavity followed by arm-locking to some combination of the inter-spacecraft distances. In order for these two stabilization stages to work simultaneously, the lock-point of the pre-stabilization loop must be frequency tunable. The current baseline stabilization technique, locking to an optical cavity, does not provide tunability between cavity resonance, which are typically spaced by 100s of MHz. Here we present a modification to the traditional Pound-Drever-Hall cavity locking technique that allows the laser to be locked to a cavity resonance with an adjustable frequency offset. This technique requires no modifications to the optical cavity itself, thus preserving the stability of the frequency reference. We present measurements of the system stability, demonstrating that the pre-stabilization level satisfies LISA requirements. We also present a demonstration of a phase-lock loop which utilizes the tunable sideband locking technique as a pre-stabilizations tage. The performance of the pre-stabilized phase-lock-loop indicates that the tunable sideband technique will meet the requirements as an actuator for arm-locking in LISA.

Thorpe, James Ira↗