Behavior of a single-turn magnetic coil under dynamic load conditions
Stress calculation for single turn magnetic coil under dynamic load conditions - plasma physics
PLASMA PHYSICS↗
SEARCH · Search NASA
Results for “Single Turn Magnet”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A Novel Single-Turn Permanent Magnet Synchronous Machine for Electric Aircraft
Explore the source record for details and available documents.
Zeyu Cheng↗
Hohlraum used as a single turn solenoid to generate seed magnetic field for inertial confinement fusion
Application of axial seed magnetic fields in the range 20-100 T that compress to greater than 10,000 T (100 MG) under typical NIF implosion conditions may significantly relax the conditions required for ignition and propagating burn in NIF ignition targets that are degraded by hydrodynamic instabilities. Such magnetic fields can: (a) permit the recovery of ignition, or at least significant alpha particle heating, in submarginal NIF targets that would otherwise fail because of adverse hydrodynamic instability growth, (b) permit the attainment of ignition in conventional cryogenic layered solid-DT targets redesigned to operate under reduced drive conditions, (c) permit the attainment of volumetric ignition in simpler, room-temperature single-shell DT gas capsules, and (d) ameliorate adverse hohlraum plasma conditions during laser drive and capsule compression. In general, an applied magnetic field should always improve the ignition condition for any NIF ignition target design.
Perkins, Lindsay John↗
Hohlraum used as a single turn solenoid to generate seed magnetic field for inertial confinement fusion
Application of axial seed magnetic fields in the range 20-100 T that compress to greater than 10,000 T (100 MG) under typical NIF implosion conditions may significantly relax the conditions required for ignition and propagating burn in NIF ignition targets that are degraded by hydrodynamic instabilities. Such magnetic fields can: (a) permit the recovery of ignition, or at least significant alpha particle heating, in submarginal NIF targets that would otherwise fail because of adverse hydrodynamic instability growth, (b) permit the attainment of ignition in conventional cryogenic layered solid-DT targets redesigned to operate under reduced drive conditions, (c) permit the attainment of volumetric ignition in simpler, room-temperature single-shell DT gas capsules, and (d) ameliorate adverse hohlraum plasma conditions during laser drive and capsule compression. In general, an applied magnetic field should always improve the ignition condition for any NIF ignition target design.
Perkins, Lindsay John↗
Inductively coupled 30 T magnetic field platform for magnetized high-energy-density plasma studies
A pulsed high magnetic field device based on the inductively coupled coil concept [D. H. Barnak et al., Rev. Sci. Instrum. 89, 033501 (2018)] is described. The device can be used for studying magnetized high-energy-density plasma and is capable of producing a pulsed magnetic field of 30 T inside a single-turn coil with an inner diameter of 6.5 mm and a length of 6.3 mm. The magnetic field is created by discharging a high-voltage capacitor through a multi-turn solenoid, which is inductively coupled to a small single-turn coil. The solenoid electric current pulse of tens of kA and a duration of several μs is inductively transformed to hundreds of kA in the single-turn coil, thus enabling a high magnetic field. Unlike directly driven single-turn systems that require a high-current and low-inductive power supply, the inductively coupled system operates using a relatively low-current power supply with very relaxed requirements for its inductance. Finally, this arrangement significantly simplifies the design of the power supply and also makes it possible to place the power supply at a significant distance from the coil. In addition, the device is designed to contain possible wire debris, which makes it attractive for debris-sensitive applications.
47 OTHER INSTRUMENTATION↗
Single Turn Shot Sequence
Pictures of a single turn shot sequence are included in this report.
36 MATERIALS SCIENCE↗
Mechanical Design of the PIP-II ORBUMP Pulsed Dipole Magnet
The Proton Improvement Plan II (PIP-II) project is a vital upgrade to the Fermilab accelerator complex. The magnet pulse rate of the PIP-II Injection system requires an increase from the current rate of 15 Hz to 20 Hz as well as a roughly 30% increase in the magnetic field of the new Orbital Bump (ORBUMP) pulsed dipole magnets in the Booster. Here, the ORBUMP magnet mechanical design is presented in this paper. The ORBUMP magnet is secured in a vacuum box and the core is made up of 0.127 mm thick, low carbon steel laminations with a C-5 inorganic magnesium phosphate coating. The core is clamped using external tie bars welded to the core end plates. ANSYS Finite Element Analysis (FEA) was used to evaluate the clamping design to minimize the deflection of the core post welding of the tie bars. The water-cooled, single turn coil, which shapes the magnetic field by acting as the pole tips, is critical for the integrated field homogeneity. The coil manufacturing tolerances and fabrication techniques were evaluated to ensure the magnetic properties of the magnet could be obtained. The coil is electrically isolated from the core using virgin Polyether ether ketone (PEEK) insulating material in the gap. An investigation into the high voltage performance of the virgin PEEK insulator was conducted via partial discharge testing using a 1:1 scale sample.
Karas, D. [Fermi National Accelerator Laboratory (↗
Electrostatic and electromagnetic turbulence associated with the earth's bow shock
Simultaneous measurements were made of the electric and magnetic field spectral densities in the earth's bow shock by a plasma wave experiment on the Imp 6 spacecraft. The frequency range of the plasma wave detector was 20 Hz to 200 kHz. Electric fields were measured with high-sensitivity 100-m long dipole antennas and magnetic fields were measured with single-turn loop antennas. Two components are distinguished in the electric field spectrum in the bow shock: one component has a broad peak centered in the region 200-800 Hz, while the other component increases monotonically with decreasing frequency. The magnetic field spectrum has only one component that increases monotonically with decreasing frequency and has an upper cutoff frequency near the local electron gyrofrequency. This magnetic field turbulence is judged to be caused by whistler mode waves. The monotonic component of the electric field spectrum is thought to be the electric field spectrum of these whistler mode waves.
Rodriguez, P.↗
Generation of strong pulsed magnetic fields using a compact, short pulse generator
The generation of strong magnetic fields (∼50 T) using single- or multi-turn coils immersed in water was studied. A pulse generator with stored energy of ∼3.6 kJ, discharge current amplitude of ∼220 kA, and rise time of ∼1.5 μs was used in these experiments. Using the advantage of water that it has a large Verdet constant, the magnetic field was measured using the non-disturbing method of Faraday rotation of a polarized collimated laser beam. This approach does not require the use of magnetic probes, which are sensitive to electromagnetic noise and damaged in each shot. It also avoids the possible formation of plasma by either a flashover along the conductor or gas breakdown inside the coil caused by an induced electric field. In addition, it was shown that this approach can be used successfully to investigate the interesting phenomenon of magnetic field enhanced diffusion into a conductor.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
ORBUMP Pulsed Dipole Magnet Design for Fermilab Booster
Fermilab initiated the accelerator magnet system upgrade project PIP-II for future neutrino experiments. Old ORBUMP pulsed dipoles should be replaced with new stronger magnets occupying the same space as old ones. Four of these magnets connected in series form dogleg type of proton beam orbit. The magnet field and 19 kA current pulse length are close to 1 ms. Old magnet cores were based on a ferrite material. For new magnets, a magnet gap field is above 0.4 T, which completely saturates ferrite material. So, for the magnet core, 0.127 mm thick laminations of low carbon steel with inorganic coating, as the magnet were placed in a vacuum box. There were investigated transient magnet parameters including skin effect in the iron core and in the single-turn copper coil. The integrated field homogeneity was improved by the copper coil shimming. Simulated by OPERA3D power losses were used for the thermal analysis by ANSYS code. The magnet performance is strongly coupled with the power source. The dynamic magnet inductance and resistance were included in the pulsed power source design. Finally, the paper presented the ORBUMP magnet system design.
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
Dynamic control of spin wave spectra using spin-polarized currents
We describe a method of controlling the spin wave spectra dynamically in a uniform nanostripe waveguide through spin-polarized currents. A stable periodic magnetization structure is observed when the current flows vertically through the center of nanostripe waveguide. After being excited, the spin wave is transmitted at the sides of the waveguide. Numerical simulations of spin-wave transmission and dispersion curves reveal a single, pronounced band gap. Moreover, the periodic magnetization structure can be turned on and off by the spin-polarized current. The switching process from full rejection to full transmission takes place within less than 3 ns. Thus, this type magnonic waveguide can be utilized for low-dissipation spin wave based filters.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Upgrades to the ion cyclotron emission diagnostic on the DIII-D tokamak
The ion cyclotron emission diagnostic on the DIII-D tokamak comprises seven single-turn loops that measure high-frequency (1–100 MHz) magnetic field fluctuations that are often excited by energetic particles in the plasma. The raw voltage signals induced in the loops in response to these fluctuations travel through a series of cables, isolation transformer DC blocks, low-pass filters, and finally a digitizer before being analyzed in frequency space. The diagnostic has been recently upgraded, most notably to include four additional graphite tile loops and a new eight-channel digitizer. The previous three loops are all on the low-field side of the tokamak. The measurement capabilities of the system have been expanded by the addition of a new horizontally oriented loop on the low-field side, an additional toroidal loop on the low-field side, and two toroidal loops on the high-field side. These loops will be used to provide approximate mode polarization, improved toroidal mode number calculations, and information on modes in inward-shifted plasmas, respectively.
47 OTHER INSTRUMENTATION↗
Computational discovery of ferromagnetic semiconducting single-layer CrSnTe 3
Despite many single-layer materials being reported in the past decade, few of them exhibit magnetism. Here we perform first-principles calculations using accurate hybrid density functional methods (HSE06) to predict that single-layer CrSnTe 3 (CST) is a ferromagnetic semiconductor, with band gaps of 0.9 and 1.2 eV for the majority and minority spin channels, respectively. We determine the Curie temperature as 170 K, significantly higher than that of single-layer CrSiTe 3 (90K) and CrGeTe 3 (130 K). This is due to the enhanced ionicity of the Sn-Te bond, which in turn increases the superexchange coupling between the magnetic Cr atoms. We further explore the mechanical and dynamical stability and strain response of this single-layer material for possible epitaxial growth. Lastly, our study provides an intuitive approach to understand and design novel single-layer magnetic semiconductors for a wide range of spintronics and energy applications.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Design and Fabrication of the Superconducting Horizontal Bend Magnet for the Super High Momentum Spectrometer at Jefferson Lab
A collaboration exists between NSCL and JLab to design and build JLab's Super High Momentum Spectrometer (SHMS) horizontal bend magnet that allows the bending of the 12 GeV/c particles horizontally by 3° to allow SHMS to reach angles as low as 5.5°. Two full size coils have been wound and are cold tested for both magnetic and structural properties. Each coil is built from 90 layers of single-turn SSC outer conductor cable. An initial test coil with one third the turns was fabricated to demonstrate that the unique saddle shape with fully contoured ends could be wound with Rutherford superconducting cable. Learned lessons during the trial winding were integrated into the two complete full-scale coils that are now installed in the helium vessel. The fabrication of the iron yoke, cold mass, and thermal shield is complete, and assembly of the vacuum vessel is in progress. This paper presents the process and progress along with the modified magnet design to reduce the fringe field in the primary beam region and also includes the impact of the changes on coil forces and coil restraint system.
43 PARTICLE ACCELERATORS↗
Diffusion Through Single And Double Layer Shields And Induced Voltages From Low Frequency Electromagnetic Environments
The diffusion through shells consisting of either a single conducting or double conducting layers are examined. Exterior drives resulting from Electromagnetic Radiation (EMR), Electromagnetic Pulse (EMP), nearby (indirect) lightning, and DC (low frequency) magnetic fields are used. Both the interior field and the induced voltage from a maximally oriented and sized single turn loop are estimated. It is shown that the loop voltage with the empty cavity bounds the case where the center region is excluded by a conducting object. The cases of interior magnetic and electric fields from an exterior magnetic drive and the interior electric field from an exterior electric drive are both solved; the magnetic interior field from an exterior magnetic drive is the only case that results in a nonzero low frequency penetration.
42 ENGINEERING↗
Magnetoelastic standing waves induced in UO 2 by microsecond magnetic field pulses
Significance UO 2 is of particular interest due to its use as a nuclear fuel, its unusually poor thermal conductivity, and its uniquely strong magnetoelastic properties characterized by a linear coupling between strain and magnetization. We clearly observe mechanical standing waves and elastic resonances in a single crystal, induced by microsecond magnetic field pulses. The phase and amplitude of the mechanical resonances are modulated by the piezomagnetic switching behavior, offering a sensitive probe for otherwise hard to detect magnetic dynamics in UO 2 . We highlight the importance of magnetic domains in the attenuation of the mechanical resonances and the robustness of the antiferromagnetic state in UO 2 against externally applied magnetic fields to 150 T.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Enhancement of beam pulse controllability for a single-pulse formation system of a cyclotron
The single-pulse formation technique using a beam chopping system consisting of two types of high-voltage beam kickers was improved to enhance the quality and intensity of the single-pulse beam with a pulse interval over 1 μs at the Japan Atomic Energy Agency cyclotron facility. A contamination rate of neighboring beam bunches in the single-pulse beam was reduced to less than 0.1%. Long-term purification of the single pulse beam was guaranteed by the well-controlled magnetic field stabilization system for the cyclotron magnet. Reduction of the multi-turn extraction number for suppressing the neighboring beam bunch contamination was achieved by restriction of a beam phase width and precise optimization of a particle acceleration phase. In addition, the single-pulse beam intensity was increased by a factor of two or more by a combination of two types of beam bunchers using sinusoidal and saw-tooth voltage waveforms. Provision of the high quality intense single-pulse beam contributed to improve the accuracy of experiments for investigation of scintillation light time-profile and for neutron energy measurement by a time-of-flight method.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
The Quench Protection of Direct Wind Magnets
The direct wind magnets have several unique features. The conductor layout is characterized by thin single conductors wound over long lengths and separated from the other turns with thick layer of insulation. Moreover, there are several layers of winding. The strong non-uniformity in the magnetic field distribution results in different current and thermal margins for quenching in different regions. The quench protection modeling involves multi-physics coupling between electrical, thermal and magnetic transient. The material properties vary over time and location. This coupled with the complexity in the geometry adds to long computation times. The objective of this study is to understand the quench propagation in an EIC high inductance direct wind magnet which enables one to design appropriate quench protection strategies to protect the magnet. An advanced modeling program has been developed to simulate direct wind magnet quench. In conclusion, we validate theoretical simulations with experimental data.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗