SEARCH · Search NASA
Results for “Size effect”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Prediction of Size Effects in Notched Laminates Using Continuum Damage Mechanics
This paper examines the use of a continuum damage model to predict strength and size effects in notched carbon-epoxy laminates. The effects of size and the development of a fracture process zone before final failure are identified in an experimental program. The continuum damage model is described and the resulting predictions of size effects are compared with alternative approaches: the point stress and the inherent flaw models, the Linear-Elastic Fracture Mechanics approach, and the strength of materials approach. The results indicate that the continuum damage model is the most accurate technique to predict size effects in composites. Furthermore, the continuum damage model does not require any calibration and it is applicable to general geometries and boundary conditions.
Size effect in composite materials and structures: Basic concepts and design considerations
Composite materials display strength characteristics that are similar to those of brittle ceramics, whose strengths are known to decrease with increasing volume for a uniform state of stress (size effect) and also are dependent on stress distribution. These similarities raise the question of whether there is also a size effect in composite materials and structures. There is significant, but inconclusive experimental evidence for the existence of a size effect in composites. Macroscopic and micromechanical statistical models have been developed which predict a size effect and are in general agreement with experimental data. The existence of a significant size effect in composites would be of great importance. For example, it would mean that use of standard test coupons to establish design allowables for large structures could be very nonconservative. Further, it would be necessary to analyze the strength of large composite structures using statistical methods, as is done for ceramics.
Statistical model for the size effect in electrical conduction.
Statistical model for size effect in electrical conduction
Projectile size effects on hypervelocity impact craters in aluminum
Projectile size effects on hypervelocity impact craters in aluminum
Characterizing the Joint Effect of Diverse Test-Statistic Correlation Structures and Effect Size on False Discovery Rates in a Multiple-Comparison Study of Many Outcome Measures
In their 2009 Annals of Statistics paper, Gavrilov, Benjamini, and Sarkar report the results of a simulation assessing the robustness of their adaptive step-down procedure (GBS) for controlling the false discovery rate (FDR) when normally distributed test statistics are serially correlated. In this study we extend the investigation to the case of multiple comparisons involving correlated non-central t-statistics, in particular when several treatments or time periods are being compared to a control in a repeated-measures design with many dependent outcome measures. In addition, we consider several dependence structures other than serial correlation and illustrate how the FDR depends on the interaction between effect size and the type of correlation structure as indexed by Foerstner s distance metric from an identity. The relationship between the correlation matrix R of the original dependent variables and R~, the correlation matrix of associated t-statistics is also studied. In general R~ depends not only on R, but also on sample size and the signed effect sizes for the multiple comparisons.
Drop size effects in spray detonations
Experimental results of drop size effects in spray detonations of liquid diethylcyclohexane
Electrode size effects in combustion-driven MHD generators
Electrode size effects on combustion driven MHD generator performance, examining voltage losses, gas boundary layer temperature and surface conditions
Anomalous size effects in the galvanomagnetic properties of zinc caused by compensation.
Anomalous size effects in galvanomagnetic properties of zinc crystal samples caused by compensation
Drop-size effects in spray detonations
Liquid diethylcyclohexane /DECH/ sprays detonation propagation in gaseous oxygen, studying drop size effect on steady state development
Study of Size Effect in Sheet-stringer Panels
An investigation was conducted to determine whether there are significant size effects in compressive strength of large Z-stiffened sheet-stringer panels as compared with geometrically similar smaller models and thus to ascertain whether the prediction of the strength of large panels by model tests is reliable. The specimens studied were manufactured from 7075-T6 aluminum alloy and included four representative types of panel designs, with full- and one-quarter-scale panels of each type.
Fundamental studies relating particle size effects to infrared spectra Final report, 1 Jun. 1967 - 31 May 1968
Infrared spectra of powdered rocks - effects of particle size, surface roughness, and spectrometer angle of view on emission spectra variations
Investigation of Pore Size Effect On Spray Cooling Heat Transfer With Porous Tunnels
Previous studies have shown that spray cooling heat flux enhancement may be attained by using enhanced surface structures. However, most enhanced surface spray cooling studies have been limited to extended surfaces relative to the base surface. In this study, experiments were conducted to study the effects of pore size on spray cooling heat flux when using porous tunnels. The porous tunnels where placed sub-surface relative to the top of the heater block. Pores of varying size were machined in the top of the heater block leading into the sub-surface tunnels. Pore diameters varied between 0.25 mm and 1.0 mm. Each copper block had a projected cross-sectional area of 2.0 cm(sup 2). Measurements were also obtained on a heater block with a flat surface for baseline comparison purposes. A 2x2 nozzle array was used with PF-5060 as the working fluid. Thermal performance data was obtained under nominally degassed (chamber pressure of 41.4 kPa) conditions with a bulk fluid temperature of 20.5 "C. Results for both the study show that the highest critical heat flux (CHF) attained was 141 w/cm2 using pores 1.0 mm in diameter. This gave an enhancement of 75% relative to the flat surface case under nominally degassed conditions.
Finite-Size Effects on the Behavior of the Susceptibility in van der Waals Films Bounded by Strongly Absorbing Substrates
We study critical point finite-size effects in the case of the susceptibility of a film in which interactions are characterized by a van der Waals-type power law tail. The geometry is appropriate to a slab-like system with two bounding surfaces. Boundary conditions are consistent with surfaces that both prefer the same phase in the low temperature, or broken symmetry, state. We take into account both interactions within the system and interactions between the constituents of the system and the material surrounding it. Specific predictions are made with respect to the behavior of 3He and 4He films in the vicinity of their respective liquid-vapor critical points.
An engineering method for estimating notch-size effect in fatigue tests on steel
Neuber's proposed method of calculating a practical factor of stress concentration for parts containing notches of arbitrary size depends on the knowledge of a "new material constant" which can be established only indirectly. In this paper, the new constant has been evaluated for a large variety of steels from fatigue tests reported in the literature, attention being confined to stresses near the endurance limit. Reasonably satisfactory results were obtained with the assumption that the constant depends only on the tensile strength of the steel. Even in cases where the notches were cracks of which only the depth was known, reasonably satisfactory agreement was found between calculated and experimental factors. It is also shown that the material constant can be used in an empirical formula to estimate the size effect on unnotched specimens tested in bending fatigue.
Fundamental studies relating particle size effects to infrared spectra Semiannual report, 1 Jun. - 30 Nov. 1967
Design criteria for circular variable filter spectrometer optical, electronic, and data handling systems for relating particle size effects to infrared spectra
The surface-brightness-effective-size relation for elliptical galaxies in the cores of clusters
Surface photometry of 372 elliptical galaxies has been performed using CCD images of the centers of 97 nearby rich Abell clusters. The strong correlation between surface brightness and effective size, originally found by Kormendy (1977), is clear in the data. Brightest cluster galaxies show much less scatter about the mean relation defined by these data than do lower-luminosity cluster ellipticals, and the slope of the relation is shallower for the brightest galaxies; these two results are tentative, however, because of uncertain selection and environmental effects. When combined with published central velocity dispersions, the photometry yields a relation for brightest cluster galaxies that is in good agreement with the mean relation for elliptical galaxies found by Djorgovski and Davis (1987). Use of the surface-brightness/scale-length relation to measure the lookback luminosity evolution of the stellar content in galaxies is promising.
Effects of Muscle Atrophy on Motor Control: Cage-size Effects
Two populations of male Sprague-Dawley rats were raised either in conventional minimum-specification cages or in a larger cage. When the animals were mature (125 to 150 d), the physiological status of the soleus (SOL) and extensor digitorum longus (EDL) muscles of the small- and large-cage animals were compared. Analysis of whole-muscle properties including the performance of the test muscle during a standardized fatigue test in which the nerve to the test muscle was subjected to supramaximal intermittent stimulation shows: (1) the amplitude, area, mean amplitude, and peak-to-peak rate of the compound muscle action potential decreased per the course of the fatigue test; (2) cage size did not affect the profile of changes for any of the action-potential measurements; (3) changes exhibited in the compound muscle action potential by SOL and EDL were substantially different; and (4) except for SOL of the large-cage rats, there was a high correlation between all four measures of the compound muscle action potential and the peak tetanic force during the fatigue test; i.e., either the electrical activity largely etermines the force profile during the fatigue test or else contractile-related activity substantially affects the compound muscle action potential.