Search NASA⌕ Search

SEARCH · Search NASA

Results for “Slag Viscosity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

A Brief Review of Viscosity Models for Slag in Coal Gasification

Many researchers have defined the phenomenon of 'slagging' as the deposition of ash in the radiative section of a boiler, while 'fouling' refers to the deposition of ash in the convective-pass region. Among the important parameters affecting ash deposition that need to be studied are ash chemistry, its transport, deposit growth, and strength development; removability of the ash deposit; heat transfer mechanisms; and the mode of operation for boilers. The heat transfer at the walls of a combustor depends on many parameters including ash deposition. This depends on the processes or parameters controlling the impact efficiency and the sticking efficiency. For a slagging combustor or furnace, however, the temperatures are so high that much of the coal particles are melted and the molten layer, in turn, captures more particles as it flows. The main problems with ash deposition are reduced heat transfer in the boiler and corrosion of the tubes. Common ways of dealing with these issues are soot blowing and wall blowing on a routine basis; however, unexpected or uncontrolled depositions can also complicate the situation, and there are always locations inaccessible to the use of such techniques. Studies have indicated that slag viscosity must be within a certain range of temperatures for tapping and the membrane wall to be accessible, for example, between 1300 C and 1500 C, the viscosity is approximately 25 Pa {center_dot} s. As the operating temperature decreases, the slag cools and solid crystals begin to form. In such cases the slag should be regarded as a non-Newtonian suspension, consisting of liquid silicate and crystals. A better understanding of the rheological properties of the slag, such as yield stress and shear-thinning, are critical in determining the optimum operating conditions. To develop an accurate heat transfer model in any type of coal combustion or gasification process, the heat transfer and to some extent the rheological properties of ash and slag, especially in high-temperature environments need to be understood and properly modeled. The viscosity of slag and the thermal conductivity of ash deposits are among two of the most important constitutive parameters that need to be studied. The accurate formulation or representations of the (transport) properties of coal (and biomass for co-firing cases) present a special challenge of modeling efforts in computational fluid dynamics applications. In this report, we first provide a brief review of the various approaches taken by different researchers in formulating or obtaining a slag viscosity model. In general, these models are based on experiments. Since slag behaves as a non-linear fluid, we discuss the constitutive modeling of slag and the important parameters that must be studied.

01 COAL, LIGNITE, AND PEAT↗

Viscosity measurements and empirical predictions for coal slags

Slag viscosity in slagging coal gasifier is an important factor affecting the gasification regime and operating cost. Most of the empirical viscosity models of coal slags that are available in the literature are applicable to only limited ranges of temperature and composition. To develop a reliable slag viscosity model, additional data are needed. Slag viscosity was measured under air or reducing atmosphere (calculated pO2~1.2 10-12 atm at 1400°C) at temperatures in the range of 1150-1550°C on 63 statistically designed slags, including 5 actual coal slag compositions and 4 validation slag compositions. The Arrhenius equation, with Arrhenius coefficients A = constant and B expressed as linear function of mass fractions of nine major components was used to fit the viscosity/temperature data. This Arrhenius relationship represents the viscosity–temperature relationship of tested slags reasonably well, = 0.981 (reducing atmosphere) and = 0.974 (air atmosphere). The validation of the model with four randomly selected slags (two from the SciGlass database and two from experimental design) indicated an accurately measured viscosity-temperature data and a fairly good predictive performance of slag viscosity models over designed compositions. The capability of the developed model to predict the viscosity of coal slags under reducing atmosphere was found to be a superior to a number of the most commonly used empirical models in the literature that are based on simplified oxide melts and British or Australian coal ash slags.

01 COAL, LIGNITE, AND PEAT↗

Novel Approach to Studying Influences of Na{sub 2}O and K{sub 2}O Additions on Viscosity and Thermodynamic Properties of BF Slags

Abstract:: The present work calculated the heat capacity, enthalpy change, and slag temperature of CaO–MgO–Al{sub 2}O{sub 3}–SiO{sub 2} slags after adding Na{sub 2}O or K{sub 2}O, and investigated the influences of Na{sub 2}O and K{sub 2}O on the slag viscosity under given temperatures and heat quantities. It was found that the slag viscosity decreases with the addition of Na{sub 2}O and tends to increase with K{sub 2}O additions at the same temperature. The heat capacity of the slag increases, while the enthalpy change decreases obviously with the increasing addition of Na{sub 2}O or K{sub 2}O. Under the constant heat quantity, an increase in content of Na{sub 2}O or K{sub 2}O of the slag leads to an appreciable increase in slag temperature, whereas the viscosity decreases significantly. Besides, the Na{sub 2}O or K{sub 2}O additions also help to stabilize the slag fluidity and lower energy consumption of blast furnace.

36 MATERIALS SCIENCE↗

An Integrated Approach to Coal Gasifier Testing, Modeling, and Process Optimization

Gasification is an important method of converting coal into clean burning fuels and high-value industrial chemicals. However, gasifier reliability can be severely limited by rapid degradation of the refractory lining in hot-wall gasifiers. The Pacific Northwest National Laboratory (PNNL) is performing multidisciplinary research to provide the experimental data and the engineering models needed to control gasifier operation for extended refractory life. Our experimental program includes prediction of slag viscosity using empirical viscosity models encompassing US coals, characterization of selected slag-refractory interaction including transport of slag/refractory components at the slag-refractory interface, and measurement of slag penetration into refractories as a function of time and temperature. The experimental data is used in slag flow, slag penetration, and refractory damage models to predict the operating temperature limits for increased refractory life. A simplified entrained flow gasifier model is also being developed to simulate one-dimensional axial flow with average axial velocity, coal devolatilization, and combustion kinetics. Combining the slag flow, refractory degradation, and gasifier models will provide a powerful tool to predict the coal and oxidant feed rates and control the gasifier operation to balance coal conversion efficiency with increased refractory life. A research scale gasifier has also been constructed at PNNL to provide syngas for coal conversion and carbon sequestration research, and also valuable datasets on operating conditions for validating the modeling results.

01 COAL, LIGNITE, AND PEAT↗

Slag Behavior in Gasifiers. Part II: Constitutive Modeling of Slag

The viscosity of slag and the thermal conductivity of ash deposits are among two of the most important constitutive parameters that need to be studied. The accurate formulation or representations of the (transport) properties of coal present a special challenge of modeling efforts in computational fluid dynamics applications. Studies have indicated that slag viscosity must be within a certain range of temperatures for tapping and the membrane wall to be accessible, for example, between 1,300 °C and 1,500 °C, the viscosity is approximately 25 Pa·s. As the operating temperature decreases, the slag cools and solid crystals begin to form. Since slag behaves as a non-linear fluid, we discuss the constitutive modeling of slag and the important parameters that must be studied. We propose a new constitutive model, where the stress tensor not only has a yield stress part, but it also has a viscous part with a shear rate dependency of the viscosity, along with temperature and concentration dependency, while allowing for the possibility of the normal stress effects. In Part I, we reviewed, identify and discuss the key coal ash properties and the operating conditions impacting slag behavior.

Massoudi, Mehrdad↗

Slag Management of Carbon Feedstock Used in Gasification FY17 TCF between Eastman Chemical and NETL (Final Report)

NETL, in collaboration with Eastman Chemical Corp (Kingsport, TN), targeted the joint evaluation and refinement of a slag management program developed by NETL (NETL IP, patent applied for) to control gasifier slag properties formed from ash in individual or combinations of different coal-based carbon feedstock materials and specific slag modifiers used in gasification. Slag forms from mineral or organic-metallic impurities in the carbon feedstock that melt at the high temperatures of gasification, coalescing to form a liquid (slag) that must flow from the gasifier. Slag additives, also known as slag modifiers, are often added to the carbon feedstock to modify the ash chemistry and achieve desired slag flow properties at target temperatures used in gasification. If slag does not flow from a gasifier, its buildup within the gasification chamber will cause either gasifier shutdown to physically remove the slag (consuming time and damaging the protective refractory lining), or the gasification temperature must be increased to lower slag viscosity so it can flow from the gasifier, leading to greater refractory wear/corrosion, along with increased fouling and downstream component wear. Because of these issues, gasification is typically targeted at the lowest temperature possible where slag will flow in a controlled manner (a temperature range called T100 for the lowest temperature, with T250 being the highest temperature where the slag has achieved the desired fluidity). That temperature range also needs to yield a desired syngas composition, highlighting the importance of knowing and being able to control carbon feedstock slag viscosity and the temperature of thermal breakdown of the carbon feedstock. Slag viscosity varies with changes in the gasification chamber temperature, oxygen partial pressure, and slag chemistry. The slag model work with Eastman Chemical targeted predicting and controlling molten coal ash slag behavior at specific gasification conditions. The final goal of the refined model was to develop/refine the NETL slag model so a gasifier operator would be able to predict slag behavior prior to purchasing or using a carbon feedstock and control slag properties once a carbon feedstock is being gasified, allowing a gasifier user to determine what mineral additives or blends of different carbon materials would be needed to achieve desired slag properties at targeted gasification conditions. For a given carbon feedstock and desired gasification condition, the actual gasification cost and slag behavior would be able to be predicted using the slag management program in advance of purchasing or using the carbon feedstock – allowing accurate control of slag ash behavior in real time. As part of the TCF project work with Eastman Chemical, the viscosity of several ash compositions of interest to them would be measured and used to populate the slag model, along with a large database of historical slag temperature, chemistry, and viscosity information they possess – information that would in-crease the predictive accuracy of the slag management model with slag ash chemistry of interest to them. As part of the model evaluation and refinement, the predictive model and its database will be installed on computers at Eastman Chemical and used to manage slag properties in a gasifier during real-time operation of their gasifier. In summary, success of the slag management program at Eastman Chemical would support its use by other gasifier operators to manage slag chemistry and properties over other desired gasification temperature ranges, allowing greater process control and efficiency of their carbon feedstock conversion during gasification.

01 COAL, LIGNITE, AND PEAT↗

Effects of Measurement Materials and Oxygen Partial Pressure on the Viscosity of synthetic Eastern and Western United States Coal Slags

The viscosity of the molten ash (slag) resulting from the mineral constituents in carbon feedstock used in slagging gasifiers is critical for controlling the gasification process. The viscosity of two synthetic slags with compositions resembling the mineral impurities in average eastern and western coal feedstock was examined at temperatures from 1300–1500 °C using a rotating bob viscometer. A few combinations of atmospheres and experimental materials were investigated with respect to one another to determine slag viscosity. A CO/CO{sub 2} atmosphere (CO/CO{sub 2} = 1.8, corresponding to a P{sub O{sub 2}} = 10–8 atm) is required to sustain ferrous ions in FeO-containing slags, an environment that is oxidizing to most metals. Iron oxide in the slag prevents usage of Fe parts. In unpurified Ar, the Fe metal surface oxidizes. Using purified argon prevents iron measurement components from oxidation; however, the metallic surfaces act as nucleation sites for the reduction of the Fe oxide in the slag into metallic Fe. Dissolution of ceramic materials into the slag, including Al{sub 2}O{sub 3} and ZrO{sub 2}, occurs in both atmospheres. Therefore, evaluating slag properties in the laboratory is challenging. The measured viscosities of two synthetic slags in this study diverged depending upon material selection. This difference is likely attributable to container/spindle-slag interactions. Viscosity measurements of the eastern coal slag using all ceramic parts agreed best with FactSage prediction above 1350 °C, with an average activation energy of 271.2 kJ. For western coal slag, the dissolution of container/spindle materials was substantial during the measurement, with precipitation of crystalline phase noted. The experimental viscosity data of the western coal slag agreed best with Kalmanovitch prediction above 1350 °C. The activation energy changed dramatically for both data sets of western coal slag, likely indicating the Newtonian-to-non-Newtonian transition.

01 COAL, LIGNITE, AND PEAT↗

Correlation between the critical viscosity and ash fusion temperatures of coal gasifier ashes

Coal gasification yields synthesis gas, an important intermediate in chemical manufacturing. It is also vital to the production of liquid fuels through the Fischer-Tropsch process and electricity in Integrated Gasification Combined Cycle power generation. Minerals naturally present in coal become molten in entrained-flow slagging gasifiers. Molten coal ash slag penetrates and dissolves refractory bricks, leading to costly plant shutdowns. The extent of coal ash slag penetration and refractory brick dissolution depends on the slag viscosity, the gasification temperature, and the composition of slag and bricks. We measured the viscosity of several synthetic coal ash slags with a high-temperature rotary viscometer and their ash fusion temperatures through optical image analysis. All measurements were made in a carbon monoxide-carbon dioxide reducing atmosphere that approximates coal gasification conditions. Empirical correlation models based on ash fusion temperatures were used to calculate critical viscosity temperatures based on the coal ash compositions. These values were then compared with those obtained from thermodynamic phase-transition models. An understanding of slag viscosity as a function of ash composition is important to reducing refractory wear in slagging coal gasifiers, which would help to reduce the cost and environmental impact of coal for chemical and electricity production.

01 COAL, LIGNITE, AND PEAT↗

Manganese Recovery by Silicothermic Reduction of MnO in BaO-MnO-MgO-CaF{sub 2} (-SiO{sub 2}) Slags

The effects of reducing agent, CaF{sub 2} content, and reaction temperature upon the silicothermic reduction of MnO in the BaO-MnO-MgO-CaF{sub 2} (-SiO{sub 2}) slags were investigated. Mn recovery was proportional to Si activity in the molten alloy. Moreover, 90 pct yield of Mn recovery was obtained under 5 mass pct CaF{sub 2} content and 1873 K (1600 °C) reaction temperature. Increasing CaF{sub 2} content above 5 pct yielded little or no further increase in Mn recovery, because it was accompanied by increased slag viscosity owing to the precipitation of high melting point compounds such as Ba{sub 2}SiO{sub 4}.

36 MATERIALS SCIENCE↗

Advanced Gasification (Annual Report)

The Advanced Gasification team is addressing many factors that impact the current and future development and deployment of gasification-based power generation. For example, the service life of gasifiers does not meet the performance needs of users, failing to achieve an online gasifier availability of 85-95 percent in utility applications and 95 percent in applications such as chemical production. The inability to meet these goals has created a potential roadblock to widespread acceptance and commercialization of advanced gasification technologies, with refractory liners, sensors, and syngas coolers among key components identified as negatively impacting gasifier availability. Ash originating from impurities in gasifier carbon feedstock is the root cause of many problems; attacking or fouling components, leading to their unplanned shutdowns for repair, replacement, or cleaning. Technology gaps exist in the understanding of how fuel properties impact carbon conversion, slag viscosity, and downstream fouling. Fuel flexibility has potential advantages for gasifier operators to lower fuel cost or impact future carbon emission credits, but operators need to know how feedstock changes impact gasifier operation. Mixed feedstock combinations have not been studied as to how ash properties impact gasifier operation, efficiency, and capacity factors. Further gaps exist in technology which specifically target reducing the cost of multiple and mixed feed stocks at 90 percent capture, including low-rank coal (half the U.S. coal supply) and affordable gas clean-up technology.

Additives↗

Understanding the Relationship Between Structure and Thermophysical Properties of CaO-SiO{sub 2}-MgO-Al{sub 2}O{sub 3} Molten Slags

In the present work, the relationship between the microscopic structure and macroscopic thermophysical properties in a basic CaO-SiO{sub 2}-MgO-Al{sub 2}O{sub 3} quaternary system was identified using Fourier transformation infrared, Raman and {sup 27}Al magic angular spinning nuclear magnetic resonance (MAS-NMR) techniques. The Raman spectra quantitatively proved that with increasing Al{sub 2}O{sub 3} content, the concentrations of the symmetric units of Q{sup 0}(Si) and Q{sup 2}(Si) decreased, while those of the asymmetric units of Q{sup 1}(Si) and Q{sup 3}(Si) increased; consequently, the degree of polymerization of the networks increased, which resulted in an increase in slag viscosity. The {sup 27}Al MAS-NMR spectra demonstrated that three structural units of Al atoms, namely, AlO{sub 4}, AlO{sub 5}, and AlO{sub 6}, mainly existed in the networks. With increasing Al{sub 2}O{sub 3} content, the concentration of AlO{sub 4} slightly decreased, while those of AlO{sub 5} and AlO{sub 6} increased; overall, Al{sub 2}O{sub 3} acted as a network former in the present system. The increasing Al{sub 2}O{sub 3} content led to additional AlO{sub 6} and Si-NBO-Ca-NBO-Al frameworks, which replaced Si-NBO-Ca-NBO-Si in the networks (NBO: non-bridging oxygen) and induced a change in the primarily precipitated crystalline phase from Ca{sub 2}MgSi{sub 2}O{sub 7} and Ca{sub 2}Al{sub 2}SiO{sub 7} to MgAlO{sub 4}.

36 MATERIALS SCIENCE↗

Effect of Iron Phase Evolution on Copper Separation from Slag Via Coal-Based Reduction

Copper slag, a by-product of copper pyrometallurgy, inevitably contains a certain amount of copper. Oxygen-enriched smelting technologies increase the copper content in slag indirectly because of the production of higher-grade matte. The effect of iron phase evolution on the copper content in slag during the slag cleaning process in an electric furnace was investigated using the method of combining theory with experiments. Based on the analysis, the main factors that impede the separation of slag and copper/matte were determined. Subsequently, the properties of slag were analyzed after decreasing the magnetite content within the slag. The experimental results showed that decreases in magnetite content were beneficial for the separation of copper and slag because of the decrease of slag viscosity. Nevertheless, Cu-Fe alloys formed when magnetite was completely reduced to metallic iron, and the foaming slag was formed at 1250 °C. Furthermore, the distribution of copper in the reduced slags was studied in detail.

36 MATERIALS SCIENCE↗

High temperature millimeter wave radiometric and interferometric measurements of slag-refractory interaction for application to coal gasifiers

Millimeter wave (MMW) radiometry can be used for simultaneous measurement of emissivity and temperature of materials under extreme environments (high temperature, pressure, and corrosive environments) such as in slagging coal gasifiers, where sensors have been identified as a key enabling technology need for process optimization. We present a state-of-the-art dual-channel MMW heterodyne radiometer with active interferometric capability that allows simultaneous radiometric measurements of sample temperature, emissivity, and flow dynamics to over 1873 K. Interferometric capability is supplied via a probe signal originating from the 137 GHz radiometer local oscillator (LO). The interferometric 'video' channels allow measurement of additional parameters simultaneously, such as volume expansion, thickness change, and slag viscosity along with temperature or emissivity. This capability has been used to demonstrate measurement of temperature and simulated coal slag infiltration into a chromia refractory brick sample as well as slag flow down a vertically placed refractory brick. Observed phenomena include slag melting and slumping, slag reboil and foam with oxygen evolution, and eventual failure of the alumina crucible through corrosion by the molten slag. These results show the promise of the MMW system for extracting quantitative and qualitative process parameters from operating slagging coal gasifiers, providing valuable information for process efficiency, control, and increased productivity.

01 COAL, LIGNITE, AND PEAT↗

Conversion of Coal Wastes and Coal Plus Other Opportunity Fuel Mixtures, Such as Coal Plus Municipal Solids, to Produce Electricity and/or Liquid Fuels

For the foreseeable future, the Nation’s energy demand will continue to come largely from indigenous fossil energy resources and hydrocarbon fuels. Specifically waste coal plus other opportunity fuels need to be utilized as a feedstock to eliminate a waste stream and optimized to maximize energy yield and cleanly minimize pollutant emissions. Modular equipment is needed for installation in coal preparation locations, military installations, and research park facilities. Thermal decomposition of coal, biomass, and mixed solid waste (MSW) have been shown to reduce a waste stream while providing liquid and gaseous fuel products with low pollutant emissions. However, thermal decomposition processes have several challenges associated with preprocessing biomass and MSW, feeding and conveying material into the reactor, and post processing of syngas to remove undesirable products while upgrading to increase yield of high value products. Increasing total energy output from power plants by utilizing biomass and mixed wastes ultimately lowers energy costs, harmful environmental impacts of emissions, and has significant impacts on the energy security and sustainability of the U.S. economy. Entrained flow gasifiers (EFGs) produce very little CH4 and a wide range of H2/CO ratios (0.5–2.0) but are limited in their ability to effectively feed large biomass or MSW particles into the reactor. A solution to the feeding problems is to use pyrolysis torrefaction (PT) for conversion of waste materials to create a feedstock similar to coal and capable of grinding down and mixing with the coal feed. Mainstream experimentally explored reaction pathways for the conversion of coal waste plus municipal solids (CWPMS) and demonstrated a bench-scale reactor used for torrefaction of the municipal solid waste (MSW) to create a coal-like feed for blending with the coal waste. The material was processed in a pilot-scale EFG to determine product yield and emissions with CWPMS fuels, as well as the ash content and slagging properties of these feedstocks. The PT-EFG system was experimentally validated, where emissions and yield data were used to develop a high-fidelity process model and economic analysis. The following was accomplished in the Phase I: Determined optimal torrefaction process conditions for MSW and biomass through TGA; maximized heating value of fuel while maximizing final mass of torrefied product Demonstrated torrefaction of MSW and biomass feedstocks at 334°C, pulverized to uniform 74 µm particle size, and processed into coal-like feedstocks Demonstrated 8 lb/h pilot-scale EFG using MSW and biomass blends with waste coal; demonstrated 100% biomass in EFG Determined major effects of MSW torrefaction and co-gasifying high-ash coal waste-MSW blends have on pilot-scale EFG Demonstrated blending low-ash, low-sulfur torrefied biomass with high-ash waste bituminous and anthracite refuse coals generates a higher quality syngas compared to syngas from high-ash waste coals Demonstrated a high carbon conversion (> 99.5%) and syngas with 29.47% H2 content, and 0% CH4 content; greater water–gas shift occurs in EFG than predicted by equilibrium ASPEN Plus model Blended lower-ash, high-alkali biomass MSW to lower slag viscosities of the high-ash coal refuse sufficiently for better slag flow compared to feeding the high-ash coal Used low-sulfur biomass to greatly reduce the EFG syngas H2S concentrations and produce non-leachable slag and quench water with very little organic and trace metal contamination Developed a process model and TEA showing the modular PT EFG is cost competitive to existing power plants with the advantage of using low- or negative-value feedstocks such as waste coal stockpiles and non-landfilled MSW; providing a large incentive to implement an economical PT-EFG process

30 DIRECT ENERGY CONVERSION↗

In Situ Observation of Calcium Aluminate Inclusions Dissolution into Steelmaking Slag

The dissolution rate of calcium aluminate inclusions in CaO-SiO{sub 2}-Al{sub 2}O{sub 3} slags has been studied using confocal scanning laser microscopy (CSLM) at elevated temperatures: 1773 K, 1823 K, and 1873 K (1500 °C, 1550 °C, and 1600 °C). The inclusion particles used in this experimental work were produced in our laboratory and their production technique is explained in detail. Even though the particles had irregular shapes, there was no rotation observed. Further, the total dissolution time decreased with increasing temperature and decreasing SiO{sub 2} content in the slag. The rate limiting steps are discussed in terms of shrinking core models and diffusion into a stagnant fluid model. It is shown that the rate limiting step for dissolution is mass transfer in the slag at 1823 K and 1873 K (1550 °C and 1600 °C). Further investigations are required to determine the dissolution mechanism at 1773 K (1500 °C). The calculated diffusion coefficients were inversely proportional to the slag viscosity and the obtained values for the systems studied ranged between 5.64 × 10{sup −12} and 5.8 × 10{sup −10} m{sup 2}/s.

36 MATERIALS SCIENCE↗

Synthetic Coal Slag Infiltration into Varying Refractory Materials

The infiltrations of synthetic coal slag into 99%Al{sub 2}O{sub 3}, 85%Al{sub 2}O{sub 3}–15%SiO{sub 2}, and 90%Cr{sub 2}O{sub 3}–10%Al{sub 2}O{sub 3} refractories with a temperature gradient induced along the penetration direction were compared to one another. The infiltrating slag was synthesized with a composition that is representative of an average of the ash contents from U S coal feedstock. Experiments were conducted with a hot-face temperature of 1450°C in a CO/CO{sub 2} atmosphere. Minimal penetration was observed in the 90%Cr{sub 2}O{sub 3}–10%Al{sub 2}O{sub 3} material because interactions between the refractory and the slag produced a protective layer of FeCr{sub 2}O{sub 4}, which impeded slag flow into the bulk of the refractory. After 5 h, the 99%Al{sub 2}O{sub 3} sample exhibited an average penetration of 12.7 mm whereas the 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} sample showed 3.8 mm. Slag infiltrated into the 99%Al{sub 2}O{sub 3} and 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} refractory systems by dissolving the respective refractories' matrix materials, which consist of fine Al{sub 2}O{sub 3} particles and an amorphous alumino-silicate phase. Due to enrichment in SiO{sub 2}, a network-former, infiltration into the 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} system yielded a higher viscosity slag and hence, a shallower penetration depth. The results suggest that slag infiltration can be limited by interactions with the refractory through the formation of either a solid layer that physically impedes fluid flow or a more viscous slag that retards infiltration.

01 COAL, LIGNITE, AND PEAT↗

Assessment of Physicochemical Properties of Electrical Arc Furnace Slag and Their Effects on Foamability

The composition of slags of an electric arc furnace (EAF) in a commercial melt shop was systematically analyzed with a focus on slag foaming. Basic behavior of FeO in an EAF slag was confirmed using fundamental thermodynamics. Monoxide ([Mg,Fe,Mn]O = M’O) and spinel ([Mg,Fe]Al{sub 2}O{sub 4}) phases in EAF slag were confirmed by X-ray diffraction analysis, and these results were interpreted in the context of equilibrium cooling calculation using FactSage™ software. Furthermore, the distribution of MgO with respect to the M’O-saturation limit at different basicity ratios (=CaO/SiO{sub 2}=C/S) and temperatures was evaluated. In particular, the relationship between MgO and FeO for C/S ratios ranging from 1.3 to 1.6 was considered with reference to phase equilibria. Foam height was affected by slag viscosity (η) and gas generation according to changes in C/S ratio and FeO content. Foaming index (Σ) decreased with the increasing C/S ratio and FeO content. The measured foam heights were relatively higher than the calculated values, and the result indicates that the effect of M’O on slag foaming in commercial process is remarkable. Therefore, slag chemistry should be optimized based on thermodynamic considerations and thermophysical properties to achieve good foaming characteristics.

36 MATERIALS SCIENCE↗

Kinetic Investigations of SiMn Slags From Different Mn Sources

The kinetics of MnO and SiO 2 reduction were investigated for Silicomanganese (SiMn) slags using a Thermogravimetric analysis (TGA) between 1773 K and 1923 K (1500 °C and 1650 °C) under CO atmospheric pressure. The charge materials were based on Assmang ore and HC FeMn Slag. Rate models for MnO and SiO 2 reduction were applied to describe the metal-producing rates, as shown by the following equations: r MnO =k MnO ×A×(a MnO -((a Mn )/(K{sub T})))r SiO 2 =k SiO 2 ×A×(a SiO 2 -((a Si )/(K T ))).The results show that the choice of raw materials in the charge considerably affected the reduction rate of MnO and SiO 2 . The highest reduction rate was found to be from charges using HC FeMn slag. The difference in the driving forces was insignificant among the SiMn slags, and the similar slag viscosities could not explain the different reduction rates. Instead, the difference is attributed to small amounts of sulfur and the amount of iron in the charge. In addition, the rate models were applicable to describe the reduction of MnO and SiO 2 in SiMn slags.

36 MATERIALS SCIENCE↗